Siec problem z konfiguracja (brak modulow)

[jacis]

Preblem jest nastepujacy przy probie uruchomienia sieci /etc/init.d/net.eth0 start wyswietla mi liste na czerwono o braku adsl i takich roznych a na koncu "no interface module has been loaded".W pliku net wszysko jest dobrze ustawione.Mam sieciowke na plycie zintegrowana nforce2 i do niej sterownik 'forcedeth',ktory jest ladowany ze startem.Instalowalem od nowa gentoo z livecd-2005.1-r1 i wszystko na poczatku bylo ok siec dzialala. Moj kernel to 2.6.12-r10 wszysko zaczelo sie od instalacji dbus,hal i ivman.Dbus zainstalowal sie i wszystkie zaleznosci ale hal i ivman nie tylko zaleznosci poniewaz najnowsze wersje wymagaja kernela w wersji >=2.6.13.Po restarcie nie dzialala juz siec.Karta jest widziana ale po route wyskakuje brak sieci.Teraz jestem w kropce bo nie moge zainstalowac nowego jadra i reszty programow.
Prosilbym o pomoc.



pozdro

[jacis]

Tutaj mam dokladnie jak wyswietla sie podczas startu systemu:

Code: Select all

 apipa does not support the required function check_installed
 arping does not support the required function provides
 bonding does not support the required function provides
 bridge does not support the required function provides
 dhclient does not support the required function provides
 dhcpcd does not support the required function provides
 essidnet does not support the required function check_installed
 ifconfig does not support the required function provides
 ifplugd does not support the required function provides
 ipppd does not support the required function provides
 iproute2 does not support the required function provides
 iptunnel does not support the required function check_installed
 iwconfig does not support the required function provides
 macchanger does not support the required function check_installed
 macnet does not support the required function check_installed
 netplugd does not support the required function provides
 pppd does not support the required function provides
 pump does not support the required function provides
 rename does not support the required function check_installed
 system does not support the required function check_installed
 tuntap does not support the required function provides
 udhcpc does not support the required function provides
 vlan does not support the required function provides
 wpa_supplicant does not support the required function provides
 ifconfig is not a valid module (missing provides) 

moze ktos wie jak ten problem rozwiazac?

[Raku]

skonfiguruj sobie dobrze /etc/conf.d/net

[jacis]

raku jezeli chodzi o /etc/conf.d/net to mam wszystko wpisane ok.

Code: Select all

# /etc/conf.d/net:
# $Header: /home/cvsroot/gentoo-src/rc-scripts/etc/conf.d/net,v 1.7 2002/11/18 19:39:22 azarah Exp $

# Global config file for net.* rc-scripts

modules=( "ifconfig" )

# This is basically the ifconfig argument without the ifconfig $iface
#
iface_eth0="192.168.2.2 broadcast 192.168.2.255 netmask 255.255.255.0"
#iface_eth1="207.170.82.202 broadcast 207.0.255.255 netmask 255.255.0.0"

# For DHCP set iface_eth? to "dhcp"
# For passing options to dhcpcd use dhcpcd_eth?
#
#iface_eth0="dhcp"
#dhcpcd_eth0="..."

# For adding aliases to a interface
#
#alias_eth0="192.168.0.3 192.168.0.4"

# NB:  The next is only used for aliases.
#
# To add a custom netmask/broadcast address to created aliases,
# uncomment and change accordingly.  Leave commented to assign
# defaults for that interface.
#
broadcast_eth0="192.168.2.1 192.168.2.1"
netmask_eth0="255.255.255.0 255.255.255.0"


# For setting the default gateway
#
gateway="eth0/192.168.2.1"

routes_eth0=( "default nvidia 192.168.2.1" )

i na tych ustawieniach wszystko dzialalo az do momentu instalacji dbus i ivman i ponownym uruchomieniu.

[milu]

zacznij używać znaczników code do umieszczania configów, wyników błędów etc!
Wyedytuj swoje posty i to popraw.