no wireless on raspberry pi 4 (solved)

Message

JumboAg · Post by **JumboAg** » Wed Oct 19, 2022 1:30 pm

Been playing with gentoo on a spare raspberry pi and cant get its wireless interface to show up after a fresh install. Not sure what I missed/did wrong. Running the 5.15 kernel. Checked that the correct firmware is in /lib/firmware. Using wired temporarily until I figure it out.

Any insight?

Code: Select all

gentoopi ~ # uname -a
Linux gentoopi 5.15.61-v8+ #1579 SMP PREEMPT Fri Aug 26 11:16:44 BST 2022 aarch64 GNU/Linux

Code: Select all

gentoopi ~ # ls -la /lib/firmware/brcm/brcmfmac43455*
-rw-r--r-- 1 root root   1723 Oct 19 08:03  /lib/firmware/brcm/brcmfmac43455-sdio.acepc-t8.txt
-rw-r--r-- 1 root root   1475 Oct 19 08:03  /lib/firmware/brcm/brcmfmac43455-sdio.AW-CM256SM.txt
lrwxrwxrwx 1 root root     33 Oct 19 08:06  /lib/firmware/brcm/brcmfmac43455-sdio.beagle,am5729-beagleboneai.txt -> brcmfmac43455-sdio.AW-CM256SM.txt
-rw-r--r-- 1 root root 631467 Oct 19 07:57  /lib/firmware/brcm/brcmfmac43455-sdio.bin
-rw-r--r-- 1 root root   7163 Oct 19 07:57  /lib/firmware/brcm/brcmfmac43455-sdio.clm_blob
-rw-r--r-- 1 root root   2510 Oct 19 08:03 '/lib/firmware/brcm/brcmfmac43455-sdio.MINIX-NEO Z83-4.txt'
lrwxrwxrwx 1 root root     33 Oct 19 08:06  /lib/firmware/brcm/brcmfmac43455-sdio.pine64,pinebook-pro.txt -> brcmfmac43455-sdio.AW-CM256SM.txt
lrwxrwxrwx 1 root root     33 Oct 19 08:06  /lib/firmware/brcm/brcmfmac43455-sdio.pine64,pinephone-pro.txt -> brcmfmac43455-sdio.AW-CM256SM.txt
lrwxrwxrwx 1 root root     33 Oct 19 08:06  /lib/firmware/brcm/brcmfmac43455-sdio.pine64,quartz64-b.txt -> brcmfmac43455-sdio.AW-CM256SM.txt
lrwxrwxrwx 1 root root     49 Oct 19 08:06  /lib/firmware/brcm/brcmfmac43455-sdio.raspberrypi,3-model-a-plus.txt -> brcmfmac43455-sdio.raspberrypi,3-model-b-plus.txt
-rw-r--r-- 1 root root   1884 Oct 19 08:03  /lib/firmware/brcm/brcmfmac43455-sdio.raspberrypi,3-model-b-plus.txt
-rw-r--r-- 1 root root   1883 Oct 19 08:03  /lib/firmware/brcm/brcmfmac43455-sdio.raspberrypi,4-model-b.txt
lrwxrwxrwx 1 root root     44 Oct 19 08:06 '/lib/firmware/brcm/brcmfmac43455-sdio.Raspberry Pi Foundation-Raspberry Pi 4 Model B.txt' -> brcmfmac43455-sdio.raspberrypi,4-model-b.txt
lrwxrwxrwx 1 root root     44 Oct 19 08:06 '/lib/firmware/brcm/brcmfmac43455-sdio.Raspberry Pi Foundation-Raspberry Pi Compute Module 4.txt' -> brcmfmac43455-sdio.raspberrypi,4-model-b.txt
-rw-r--r-- 1 root root   2074 Oct 19 07:57  /lib/firmware/brcm/brcmfmac43455-sdio.txt

Code: Select all

gentoopi ~ # grep boardflags3 /lib/firmware/brcm/brcmfmac43455-sdio.txt
boardflags3=0x44200100

Code: Select all

gentoopi ~ # ifconfig -a
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 192.168.86.61  netmask 255.255.255.0  broadcast 192.168.86.255
        ether dc:a6:32:06:06:f1  txqueuelen 1000  (Ethernet)
        RX packets 2058  bytes 252426 (246.5 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 382  bytes 52769 (51.5 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        loop  txqueuelen 1000  (Local Loopback)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

Code: Select all

gentoopi ~ # dmesg
[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083]
[    0.000000] Linux version 5.15.61-v8+ (dom@buildbot) (aarch64-linux-gnu-gcc-8 (Ubuntu/Linaro 8.4.0-3ubuntu1) 8.4.0, GNU ld (GNU Binutils for Ubuntu) 2.34) #1579 SMP PREEMPT Fri Aug 26 11:16:44 BST 2022
[    0.000000] random: crng init done
[    0.000000] Machine model: Raspberry Pi 4 Model B Rev 1.1
[    0.000000] efi: UEFI not found.
[    0.000000] Reserved memory: created CMA memory pool at 0x000000001ac00000, size 320 MiB
[    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000000000-0x000000003fffffff]
[    0.000000]   DMA32    [mem 0x0000000040000000-0x000000007fffffff]
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x000000003b3fffff]
[    0.000000]   node   0: [mem 0x0000000040000000-0x000000007fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fffffff]
[    0.000000] On node 0, zone DMA32: 19456 pages in unavailable ranges
[    0.000000] percpu: Embedded 28 pages/cpu s77272 r8192 d29224 u114688
[    0.000000] pcpu-alloc: s77272 r8192 d29224 u114688 alloc=28*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[    0.000000] Detected PIPT I-cache on CPU0
[    0.000000] CPU features: detected: Spectre-v2
[    0.000000] CPU features: detected: Spectre-v3a
[    0.000000] CPU features: detected: Spectre-v4
[    0.000000] CPU features: detected: Spectre-BHB
[    0.000000] CPU features: kernel page table isolation forced ON by KASLR
[    0.000000] CPU features: detected: Kernel page table isolation (KPTI)
[    0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 496944
[    0.000000] Kernel command line: coherent_pool=1M 8250.nr_uarts=0 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1 video=HDMI-A-1:1920x1080M@60,margin_left=48,margin_right=48,margin_top=48,margin_bottom=48 smsc95xx.macaddr=DC:A6:32:06:06:F1 vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000  console=ttyS0,115200 console=tty1 root=PARTUUID=dd08d348-03 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait
[    0.000000] Kernel parameter elevator= does not have any effect anymore.
               Please use sysfs to set IO scheduler for individual devices.
[    0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[    0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] software IO TLB: mapped [mem 0x0000000037400000-0x000000003b400000] (64MB)
[    0.000000] Memory: 1562108K/2019328K available (11520K kernel code, 1956K rwdata, 4140K rodata, 3840K init, 974K bss, 129540K reserved, 327680K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] ftrace: allocating 38040 entries in 149 pages
[    0.000000] ftrace: allocated 149 pages with 4 groups
[    0.000000] trace event string verifier disabled
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu:     RCU event tracing is enabled.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4.
[    0.000000]  Trampoline variant of Tasks RCU enabled.
[    0.000000]  Rude variant of Tasks RCU enabled.
[    0.000000]  Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] Root IRQ handler: gic_handle_irq
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] arch_timer: cp15 timer(s) running at 54.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xc743ce346, max_idle_ns: 440795203123 ns
[    0.000001] sched_clock: 56 bits at 54MHz, resolution 18ns, wraps every 4398046511102ns
[    0.000327] Console: colour dummy device 80x25
[    0.000907] printk: console [tty1] enabled
[    0.000981] Calibrating delay loop (skipped), value calculated using timer frequency.. 108.00 BogoMIPS (lpj=216000)
[    0.001022] pid_max: default: 32768 minimum: 301
[    0.001167] LSM: Security Framework initializing
[    0.001416] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.001473] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.002796] cgroup: Disabling memory control group subsystem
[    0.005600] rcu: Hierarchical SRCU implementation.
[    0.006767] EFI services will not be available.
[    0.007333] smp: Bringing up secondary CPUs ...
[    0.008523] Detected PIPT I-cache on CPU1
[    0.008609] CPU1: Booted secondary processor 0x0000000001 [0x410fd083]
[    0.009812] Detected PIPT I-cache on CPU2
[    0.009864] CPU2: Booted secondary processor 0x0000000002 [0x410fd083]
[    0.010995] Detected PIPT I-cache on CPU3
[    0.011046] CPU3: Booted secondary processor 0x0000000003 [0x410fd083]
[    0.011200] smp: Brought up 1 node, 4 CPUs
[    0.011289] SMP: Total of 4 processors activated.
[    0.011309] CPU features: detected: 32-bit EL0 Support
[    0.011327] CPU features: detected: 32-bit EL1 Support
[    0.011349] CPU features: detected: CRC32 instructions
[    0.043633] CPU: All CPU(s) started at EL2
[    0.043735] alternatives: patching kernel code
[    0.045341] devtmpfs: initialized
[    0.056461] Enabled cp15_barrier support
[    0.056533] Enabled setend support
[    0.056562] KASLR enabled
[    0.056773] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.056825] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.066288] pinctrl core: initialized pinctrl subsystem
[    0.067194] DMI not present or invalid.
[    0.067933] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.071724] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations
[    0.072050] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.073013] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.073134] audit: initializing netlink subsys (disabled)
[    0.073451] audit: type=2000 audit(0.072:1): state=initialized audit_enabled=0 res=1
[    0.074011] thermal_sys: Registered thermal governor 'step_wise'
[    0.074241] cpuidle: using governor menu
[    0.074590] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.074807] ASID allocator initialised with 32768 entries
[    0.074977] Serial: AMBA PL011 UART driver
[    0.085259] bcm2835-mbox fe00b880.mailbox: mailbox enabled
[    0.100457] raspberrypi-firmware soc:firmware: Attached to firmware from 2022-08-26T14:03:16, variant start
[    0.104481] raspberrypi-firmware soc:firmware: Firmware hash is 102f1e848393c2112206fadffaaf86db04e98326
[    0.155425] bcm2835-dma fe007000.dma: DMA legacy API manager, dmachans=0x1
[    0.159676] vgaarb: loaded
[    0.160143] SCSI subsystem initialized
[    0.160364] usbcore: registered new interface driver usbfs
[    0.160428] usbcore: registered new interface driver hub
[    0.160506] usbcore: registered new device driver usb
[    0.160953] usb_phy_generic phy: supply vcc not found, using dummy regulator
[    0.161175] usb_phy_generic phy: dummy supplies not allowed for exclusive requests
[    0.161502] pps_core: LinuxPPS API ver. 1 registered
[    0.161526] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.161563] PTP clock support registered
[    0.163135] clocksource: Switched to clocksource arch_sys_counter
[    0.251727] VFS: Disk quotas dquot_6.6.0
[    0.251861] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.252047] FS-Cache: Loaded
[    0.252307] CacheFiles: Loaded
[    0.253558] simple-framebuffer 3e4e0000.framebuffer: framebuffer at 0x3e4e0000, 0x6e7000 bytes
[    0.253595] simple-framebuffer 3e4e0000.framebuffer: format=a8r8g8b8, mode=1824x984x32, linelength=7296
[    0.264152] Console: switching to colour frame buffer device 228x61
[    0.273572] simple-framebuffer 3e4e0000.framebuffer: fb0: simplefb registered!
[    0.284222] NET: Registered PF_INET protocol family
[    0.284662] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.286673] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear)
[    0.286805] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.286909] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.287147] TCP bind hash table entries: 16384 (order: 6, 262144 bytes, linear)
[    0.287507] TCP: Hash tables configured (established 16384 bind 16384)
[    0.287811] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear)
[    0.287931] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear)
[    0.288277] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.289421] RPC: Registered named UNIX socket transport module.
[    0.289508] RPC: Registered udp transport module.
[    0.289567] RPC: Registered tcp transport module.
[    0.289626] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.289712] PCI: CLS 0 bytes, default 64
[    0.292353] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
[    0.292805] kvm [1]: IPA Size Limit: 44 bits
[    0.294054] kvm [1]: vgic interrupt IRQ9
[    0.294396] kvm [1]: Hyp mode initialized successfully
[    1.082644] Initialise system trusted keyrings
[    1.083180] workingset: timestamp_bits=46 max_order=19 bucket_order=0
[    1.090167] zbud: loaded
[    1.092074] FS-Cache: Netfs 'nfs' registered for caching
[    1.092860] NFS: Registering the id_resolver key type
[    1.092967] Key type id_resolver registered
[    1.093027] Key type id_legacy registered
[    1.093199] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    1.093283] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[    1.094600] Key type asymmetric registered
[    1.094668] Asymmetric key parser 'x509' registered
[    1.097468] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    1.100351] io scheduler mq-deadline registered
[    1.103008] io scheduler kyber registered
[    1.113819] brcm-pcie fd500000.pcie: host bridge /scb/pcie@7d500000 ranges:
[    1.116478] brcm-pcie fd500000.pcie:   No bus range found for /scb/pcie@7d500000, using [bus 00-ff]
[    1.119265] brcm-pcie fd500000.pcie:      MEM 0x0600000000..0x063fffffff -> 0x00c0000000
[    1.122061] brcm-pcie fd500000.pcie:   IB MEM 0x0000000000..0x007fffffff -> 0x0400000000
[    1.173247] brcm-pcie fd500000.pcie: link up, 5.0 GT/s PCIe x1 (SSC)
[    1.176343] brcm-pcie fd500000.pcie: PCI host bridge to bus 0000:00
[    1.179047] pci_bus 0000:00: root bus resource [bus 00-ff]
[    1.181688] pci_bus 0000:00: root bus resource [mem 0x600000000-0x63fffffff] (bus address [0xc0000000-0xffffffff])
[    1.184471] pci 0000:00:00.0: [14e4:2711] type 01 class 0x060400
[    1.187454] pci 0000:00:00.0: PME# supported from D0 D3hot
[    1.194233] pci 0000:01:00.0: [1106:3483] type 00 class 0x0c0330
[    1.197076] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00000fff 64bit]
[    1.200124] pci 0000:01:00.0: PME# supported from D0 D3cold
[    1.206700] pci 0000:00:00.0: BAR 8: assigned [mem 0x600000000-0x6000fffff]
[    1.209418] pci 0000:01:00.0: BAR 0: assigned [mem 0x600000000-0x600000fff 64bit]
[    1.212106] pci 0000:00:00.0: PCI bridge to [bus 01]
[    1.214708] pci 0000:00:00.0:   bridge window [mem 0x600000000-0x6000fffff]
[    1.228509] iproc-rng200 fe104000.rng: hwrng registered
[    1.231576] vc-mem: phys_addr:0x00000000 mem_base=0x3ec00000 mem_size:0x40000000(1024 MiB)
[    1.235524] gpiomem-bcm2835 fe200000.gpiomem: Initialised: Registers at 0xfe200000
[    1.250871] brd: module loaded
[    1.263482] loop: module loaded
[    1.266757] Loading iSCSI transport class v2.0-870.
[    1.274363] bcmgenet fd580000.ethernet: GENET 5.0 EPHY: 0x0000
[    1.335297] unimac-mdio unimac-mdio.-19: Broadcom UniMAC MDIO bus
[    1.339077] usbcore: registered new interface driver r8152
[    1.341755] usbcore: registered new interface driver lan78xx
[    1.344333] usbcore: registered new interface driver smsc95xx
[    1.348393] pci 0000:00:00.0: enabling device (0000 -> 0002)
[    1.350836] xhci_hcd 0000:01:00.0: enabling device (0000 -> 0002)
[    1.353421] xhci_hcd 0000:01:00.0: xHCI Host Controller
[    1.355887] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 1
[    1.359092] xhci_hcd 0000:01:00.0: hcc params 0x002841eb hci version 0x100 quirks 0x00003c0000000890
[    1.362677] xhci_hcd 0000:01:00.0: xHCI Host Controller
[    1.365081] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
[    1.367559] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed
[    1.370486] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.15
[    1.373067] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.375605] usb usb1: Product: xHCI Host Controller
[    1.378076] usb usb1: Manufacturer: Linux 5.15.61-v8+ xhci-hcd
[    1.380592] usb usb1: SerialNumber: 0000:01:00.0
[    1.383729] hub 1-0:1.0: USB hub found
[    1.386268] hub 1-0:1.0: 1 port detected
[    1.389736] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.15
[    1.392267] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.394761] usb usb2: Product: xHCI Host Controller
[    1.397297] usb usb2: Manufacturer: Linux 5.15.61-v8+ xhci-hcd
[    1.399692] usb usb2: SerialNumber: 0000:01:00.0
[    1.402849] hub 2-0:1.0: USB hub found
[    1.405429] hub 2-0:1.0: 4 ports detected
[    1.409546] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[    1.412496] dwc_otg: FIQ enabled
[    1.412509] dwc_otg: NAK holdoff enabled
[    1.412519] dwc_otg: FIQ split-transaction FSM enabled
[    1.412533] Module dwc_common_port init
[    1.413122] usbcore: registered new interface driver uas
[    1.415605] usbcore: registered new interface driver usb-storage
[    1.418236] mousedev: PS/2 mouse device common for all mice
[    1.425606] sdhci: Secure Digital Host Controller Interface driver
[    1.428101] sdhci: Copyright(c) Pierre Ossman
[    1.431016] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.436762] ledtrig-cpu: registered to indicate activity on CPUs
[    1.439790] hid: raw HID events driver (C) Jiri Kosina
[    1.442364] usbcore: registered new interface driver usbhid
[    1.444806] usbhid: USB HID core driver
[    1.447548] ashmem: initialized
[    1.458556] NET: Registered PF_PACKET protocol family
[    1.461218] Key type dns_resolver registered
[    1.464890] registered taskstats version 1
[    1.467268] Loading compiled-in X.509 certificates
[    1.470269] Key type ._fscrypt registered
[    1.472657] Key type .fscrypt registered
[    1.474978] Key type fscrypt-provisioning registered
[    1.488843] uart-pl011 fe201000.serial: there is not valid maps for state default
[    1.491597] uart-pl011 fe201000.serial: cts_event_workaround enabled
[    1.494137] fe201000.serial: ttyAMA0 at MMIO 0xfe201000 (irq = 17, base_baud = 0) is a PL011 rev2
[    1.505576] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer
[    1.508511] bcm2835-power bcm2835-power: Broadcom BCM2835 power domains driver
[    1.512132] mmc-bcm2835 fe300000.mmcnr: mmc_debug:0 mmc_debug2:0
[    1.514484] mmc-bcm2835 fe300000.mmcnr: DMA channel allocated
[    1.548535] of_cfs_init
[    1.550995] of_cfs_init: OK
[    1.581295] mmc0: SDHCI controller on fe340000.mmc [fe340000.mmc] using ADMA
[    1.584324] Waiting for root device PARTUUID=dd08d348-03...
[    1.643223] usb 1-1: new high-speed USB device number 2 using xhci_hcd
[    1.657404] mmc1: new high speed SDIO card at address 0001
[    1.688892] mmc0: new ultra high speed DDR50 SDHC card at address 0001
[    1.692400] mmcblk0: mmc0:0001 EB1QT 29.8 GiB
[    1.698127]  mmcblk0: p1 p2 p3
[    1.701353] mmcblk0: mmc0:0001 EB1QT 29.8 GiB
[    1.722066] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none.
[    1.724821] VFS: Mounted root (ext4 filesystem) readonly on device 179:3.
[    1.733146] devtmpfs: mounted
[    1.743885] Freeing unused kernel memory: 3840K
[    1.746575] Run /sbin/init as init process
[    1.748953]   with arguments:
[    1.748963]     /sbin/init
[    1.748972]   with environment:
[    1.748981]     HOME=/
[    1.748991]     TERM=linux
[    1.797834] usb 1-1: New USB device found, idVendor=2109, idProduct=3431, bcdDevice= 4.21
[    1.800533] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    1.803279] usb 1-1: Product: USB2.0 Hub
[    1.808522] hub 1-1:1.0: USB hub found
[    1.811265] hub 1-1:1.0: 4 ports detected
[    2.107217] usb 1-1.1: new low-speed USB device number 3 using xhci_hcd
[    2.228720] usb 1-1.1: New USB device found, idVendor=04d9, idProduct=1203, bcdDevice= 2.80
[    2.231423] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    2.253768] input: HID 04d9:1203 as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.1/1-1.1:1.0/0003:04D9:1203.0001/input/input0
[    2.320039] hid-generic 0003:04D9:1203.0001: input,hidraw0: USB HID v1.11 Keyboard [HID 04d9:1203] on usb-0000:01:00.0-1.1/input0
[    2.345264] input: HID 04d9:1203 System Control as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.1/1-1.1:1.1/0003:04D9:1203.0002/input/input1
[    2.407689] input: HID 04d9:1203 Consumer Control as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.1/1-1.1:1.1/0003:04D9:1203.0002/input/input2
[    2.411382] hid-generic 0003:04D9:1203.0002: input,hidraw1: USB HID v1.11 Device [HID 04d9:1203] on usb-0000:01:00.0-1.1/input1
[    2.499191] usb 1-1.2: new low-speed USB device number 4 using xhci_hcd
[    2.614983] usb 1-1.2: New USB device found, idVendor=046d, idProduct=c404, bcdDevice= 2.20
[    2.618409] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.621743] usb 1-1.2: Product: Trackball
[    2.625176] usb 1-1.2: Manufacturer: Logitech
[    2.640985] input: Logitech Trackball as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.2/1-1.2:1.0/0003:046D:C404.0003/input/input3
[    2.645117] hid-generic 0003:046D:C404.0003: input,hidraw2: USB HID v1.10 Mouse [Logitech Trackball] on usb-0000:01:00.0-1.2/input0
[    9.640603] EXT4-fs (mmcblk0p3): re-mounted. Opts: (null). Quota mode: none.
[   10.155512] Adding 2097148k swap on /dev/mmcblk0p2.  Priority:-2 extents:1 across:2097148k SSFS
[   14.032793] bcmgenet fd580000.ethernet: configuring instance for external RGMII (RX delay)
[   14.034258] bcmgenet fd580000.ethernet eth0: Link is Down
[   16.046718] uart-pl011 fe201000.serial: no DMA platform data
[   18.111370] bcmgenet fd580000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[   31.711194] cam-dummy-reg: disabling

pingtoo · Post by **pingtoo** » Wed Oct 19, 2022 2:18 pm

Can you share /boot/config.txt?

I suspect you disable your wifi in device tree.

JumboAg · Post by **JumboAg** » Wed Oct 19, 2022 2:22 pm

Code: Select all

gentoopi ~ # cat /boot/config.txt
# For more options and information see
# http://rpf.io/configtxt
# Some settings may impact device functionality. See link above for details

# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1

# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
#disable_overscan=1

# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16

# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720

# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1

# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1

# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
hdmi_drive=2

# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4

# uncomment for composite PAL
#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800

# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on

# Uncomment this to enable infrared communication.
#dtoverlay=gpio-ir,gpio_pin=17
#dtoverlay=gpio-ir-tx,gpio_pin=18

# Additional overlays and parameters are documented /boot/overlays/README

# Enable audio (loads snd_bcm2835)
dtparam=audio=on

[pi4]
# Enable DRM VC4 V3D driver on top of the dispmanx display stack
dtoverlay=vc4-fkms-v3d
max_framebuffers=2

[all]
#dtoverlay=vc4-fkms-v3d
arm_64bit=1

And for good measure:

Code: Select all

gentoopi /boot # cat cmdline.txt
console=serial0,115200 console=tty1 root=PARTUUID=dd08d348-03 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait

pingtoo · Post by **pingtoo** » Thu Oct 20, 2022 3:39 am

Thanks!

Or is it possible you blocklist modules?

Do you have brcmfmac and brcmutil both modules loaded?

JumboAg · Post by **JumboAg** » Thu Oct 20, 2022 9:08 pm

according to lsmod, no modules are loading for me. I may have found my problem. Somehow my nodules directory doesnt seem to match my kernel version. Going to recompile everything and try cleaning things up for another try.

JumboAg · Post by **JumboAg** » Fri Oct 21, 2022 1:46 pm

Confirmed: It was a version mismatch with all the modules. How I messed it up no idea but everything matches now and all the modules I would expect to see load have (including wireless)