Code: Select all
dmesg
[ 1.331401] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
[ 1.334331] kvm: Nested Virtualization enabled
[ 1.334335] kvm: Nested Paging enabled
[ 1.334713] LVT offset 1 assigned for vector 0x400
[ 1.334722] IBS: LVT offset 1 assigned
[ 1.334735] perf: AMD IBS detected (0x0000001f)
[ 1.334963] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 1.335060] audit: initializing netlink subsys (disabled)
[ 1.335077] audit: type=2000 audit(1443343345.224:1): initialized
[ 1.335532] VFS: Disk quotas dquot_6.5.2
[ 1.335567] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.335714] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.335788] fuse init (API version 7.23)
[ 1.335835] SGI XFS with ACLs, security attributes, realtime, no debug enabled
[ 1.336049] ocfs2: Registered cluster interface o2cb
[ 1.336093] OCFS2 User DLM kernel interface loaded
[ 1.336400] gfs2: GFS2 installed
[ 1.336639] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 1.336642] io scheduler noop registered
[ 1.336643] io scheduler deadline registered
[ 1.336654] io scheduler cfq registered (default)
[ 1.336945] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.357280] 00:03: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[ 1.357561] Linux agpgart interface v0.103
[ 1.357569] vesafb: mode is 1280x1024x32, linelength=5120, pages=0
[ 1.357570] vesafb: scrolling: redraw
[ 1.357571] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 1.357580] vesafb: framebuffer at 0xf9000000, mapped to 0xffffc90010100000, using 5120k, total 5120k
[ 1.373386] Console: switching to colour frame buffer device 160x64
[ 1.388522] fb0: VESA VGA frame buffer device
[ 1.389676] brd: module loaded
[ 1.390525] loop: module loaded
[ 1.390570] i8042: PNP: No PS/2 controller found. Probing ports directly.
[ 1.390919] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.390925] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.391089] mousedev: PS/2 mouse device common for all mice
[ 1.391217] f71882fg: Found f71889a chip at 0x480, revision 49
[ 1.391299] f71882fg f71882fg.1152: Fan: 1 is in duty-cycle mode
[ 1.391319] f71882fg f71882fg.1152: Fan: 2 is in duty-cycle mode
[ 1.391336] f71882fg f71882fg.1152: Fan: 3 is in duty-cycle mode
[ 1.391409] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.391483] TCP: cubic registered
[ 1.391485] NET: Registered protocol family 17
[ 1.391857] registered taskstats version 1
[ 1.392164] Btrfs loaded, assert=on
[ 1.392181] BTRFS: selftest: Running btrfs free space cache tests
[ 1.392182] BTRFS: selftest: Running extent only tests
[ 1.392185] BTRFS: selftest: Running bitmap only tests
[ 1.392190] BTRFS: selftest: Running bitmap and extent tests
[ 1.392195] BTRFS: selftest: Running space stealing from bitmap to extent
[ 1.392376] BTRFS: selftest: Free space cache tests finished
[ 1.392376] BTRFS: selftest: Running extent buffer operation tests
[ 1.392377] BTRFS: selftest: Running btrfs_split_item tests
[ 1.392386] BTRFS: selftest: Running find delalloc tests
[ 1.424140] BTRFS: selftest: Running btrfs_get_extent tests
[ 1.424185] BTRFS: selftest: Running hole first btrfs_get_extent test
[ 1.424191] BTRFS: selftest: Running outstanding_extents tests
[ 1.424206] BTRFS: selftest: Running qgroup tests
[ 1.424206] BTRFS: selftest: Qgroup basic add
[ 1.424212] BTRFS: selftest: Qgroup multiple refs test
[ 1.448437] drivers/rtc/hctosys.c: unable to open rtc device ()
[ 1.448590] ALSA device list:
[ 1.448590] No soundcards found.
[ 1.448951] Freeing unused kernel memory: 992K (ffffffff81a85000 - ffffffff81b7d000)
[ 1.698604] libata version 3.00 loaded.
[ 1.826414] ahci 0000:00:11.0: version 3.0
[ 1.826586] ahci 0000:00:11.0: AHCI 0001.0200 32 slots 6 ports 6 Gbps 0x3f impl SATA mode
[ 1.826589] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part
[ 1.827310] scsi host0: ahci
[ 1.827550] scsi host1: ahci
[ 1.827688] scsi host2: ahci
[ 1.827807] scsi host3: ahci
[ 1.827920] scsi host4: ahci
[ 1.828030] scsi host5: ahci
[ 1.828091] ata1: SATA max UDMA/133 abar m1024@0xfe30b000 port 0xfe30b100 irq 19
[ 1.828094] ata2: SATA max UDMA/133 abar m1024@0xfe30b000 port 0xfe30b180 irq 19
[ 1.828095] ata3: SATA max UDMA/133 abar m1024@0xfe30b000 port 0xfe30b200 irq 19
[ 1.828097] ata4: SATA max UDMA/133 abar m1024@0xfe30b000 port 0xfe30b280 irq 19
[ 1.828099] ata5: SATA max UDMA/133 abar m1024@0xfe30b000 port 0xfe30b300 irq 19
[ 1.828101] ata6: SATA max UDMA/133 abar m1024@0xfe30b000 port 0xfe30b380 irq 19
[ 2.147397] ata2: SATA link down (SStatus 0 SControl 300)
[ 2.147445] ata5: SATA link down (SStatus 0 SControl 300)
[ 2.151436] ata3: SATA link down (SStatus 0 SControl 300)
[ 2.315238] ata6: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 2.315701] ata6.00: ATA-9: WDC WD30EZRX-00SPEB0, 80.00A80, max UDMA/133
[ 2.315703] ata6.00: 5860533168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 2.316209] ata6.00: configured for UDMA/133
[ 2.323241] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2.324880] ata1.00: ATAPI: Optiarc DVD RW AD-5280S, 1.Z8, max UDMA/100
[ 2.326689] ata1.00: configured for UDMA/100
[ 2.327244] ata4: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 2.327789] ata4.00: supports DRM functions and may not be fully accessible
[ 2.327844] scsi 0:0:0:0: CD-ROM Optiarc DVD RW AD-5280S 1.Z8 PQ: 0 ANSI: 5
[ 2.327899] ata4.00: ATA-9: ST1000DM003-1ER162, CC43, max UDMA/133
[ 2.327901] ata4.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 2.328408] ata4.00: supports DRM functions and may not be fully accessible
[ 2.328506] ata4.00: configured for UDMA/133
[ 2.331213] tsc: Refined TSC clocksource calibration: 3300.176 MHz
[ 2.345224] sr 0:0:0:0: [sr0] scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[ 2.345231] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 2.345456] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 2.345634] scsi 3:0:0:0: Direct-Access ATA ST1000DM003-1ER1 CC43 PQ: 0 ANSI: 5
[ 2.345842] sd 3:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 2.345844] sd 3:0:0:0: [sda] 4096-byte physical blocks
[ 2.345900] scsi 5:0:0:0: Direct-Access ATA WDC WD30EZRX-00S 0A80 PQ: 0 ANSI: 5
[ 2.345907] sd 3:0:0:0: [sda] Write Protect is off
[ 2.345910] sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.345941] sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.346172] sd 5:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
[ 2.346173] sd 5:0:0:0: [sdb] 4096-byte physical blocks
[ 2.346223] sd 5:0:0:0: [sdb] Write Protect is off
[ 2.346226] sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 2.346239] sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.391956] sda: sda1 sda2 sda3
[ 2.392329] sd 3:0:0:0: [sda] Attached SCSI disk
[ 2.901074] sd 5:0:0:0: [sdb] Attached SCSI disk
[ 2.918225] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 2.918296] sd 3:0:0:0: Attached scsi generic sg1 type 0
[ 2.918342] sd 5:0:0:0: Attached scsi generic sg2 type 0
[ 2.963007] scsi: <fdomain> Detection failed (no card)
[ 3.024420] GDT-HA: Storage RAID Controller Driver. Version: 3.05
[ 3.083152] imm: Version 2.05 (for Linux 2.4.0)
[ 3.125232] Fusion MPT base driver 3.04.20
[ 3.125234] Copyright (c) 1999-2008 LSI Corporation
[ 3.128753] Fusion MPT SPI Host driver 3.04.20
[ 3.130528] Fusion MPT FC Host driver 3.04.20
[ 3.132580] Fusion MPT SAS Host driver 3.04.20
[ 3.134061] 3ware Storage Controller device driver for Linux v1.26.02.003.
[ 3.135411] 3ware 9000 Storage Controller device driver for Linux v2.26.02.014.
[ 3.141430] HP CISS Driver (v 3.6.26)
[ 3.150739] Adaptec aacraid driver 1.2-0[30300]-ms
[ 3.153585] megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
[ 3.153842] megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
[ 3.156804] megasas: 06.806.08.00-rc1
[ 3.159722] qla2xxx [0000:00:00.0]-0005: : QLogic Fibre Channel HBA Driver: 8.07.00.16-k.
[ 3.169508] Emulex LightPulse Fibre Channel SCSI driver 10.4.8000.0.
[ 3.169509] Copyright(c) 2004-2014 Emulex. All rights reserved.
[ 3.173451] aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded
[ 3.181130] ACPI: bus type USB registered
[ 3.181172] usbcore: registered new interface driver usbfs
[ 3.181189] usbcore: registered new interface driver hub
[ 3.181243] usbcore: registered new device driver usb
[ 3.181492] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.181581] ehci-pci: EHCI PCI platform driver
[ 3.181690] QUIRK: Enable AMD PLL fix
[ 3.181743] ehci-pci 0000:00:12.2: EHCI Host Controller
[ 3.181749] ehci-pci 0000:00:12.2: new USB bus registered, assigned bus number 1
[ 3.181761] ehci-pci 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 3.181769] ehci-pci 0000:00:12.2: debug port 1
[ 3.181799] ehci-pci 0000:00:12.2: irq 17, io mem 0xfe309000
[ 3.190422] ehci-pci 0000:00:12.2: USB 2.0 started, EHCI 1.00
[ 3.190682] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.190685] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.190686] usb usb1: Product: EHCI Host Controller
[ 3.190687] usb usb1: Manufacturer: Linux 4.0.5-gentoo-syd ehci_hcd
[ 3.190688] usb usb1: SerialNumber: 0000:00:12.2
[ 3.190813] hub 1-0:1.0: USB hub found
[ 3.190831] hub 1-0:1.0: 5 ports detected
[ 3.191050] ehci-pci 0000:00:13.2: EHCI Host Controller
[ 3.191055] ehci-pci 0000:00:13.2: new USB bus registered, assigned bus number 2
[ 3.191058] ehci-pci 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 3.191065] ehci-pci 0000:00:13.2: debug port 1
[ 3.191088] ehci-pci 0000:00:13.2: irq 17, io mem 0xfe307000
[ 3.202450] ehci-pci 0000:00:13.2: USB 2.0 started, EHCI 1.00
[ 3.202686] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.202688] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.202689] usb usb2: Product: EHCI Host Controller
[ 3.202690] usb usb2: Manufacturer: Linux 4.0.5-gentoo-syd ehci_hcd
[ 3.202691] usb usb2: SerialNumber: 0000:00:13.2
[ 3.202832] hub 2-0:1.0: USB hub found
[ 3.202859] hub 2-0:1.0: 5 ports detected
[ 3.203078] ehci-pci 0000:00:16.2: EHCI Host Controller
[ 3.203083] ehci-pci 0000:00:16.2: new USB bus registered, assigned bus number 3
[ 3.203086] ehci-pci 0000:00:16.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 3.203095] ehci-pci 0000:00:16.2: debug port 1
[ 3.203119] ehci-pci 0000:00:16.2: irq 17, io mem 0xfe304000
[ 3.214406] ehci-pci 0000:00:16.2: USB 2.0 started, EHCI 1.00
[ 3.214633] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.214640] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.214644] usb usb3: Product: EHCI Host Controller
[ 3.214649] usb usb3: Manufacturer: Linux 4.0.5-gentoo-syd ehci_hcd
[ 3.214653] usb usb3: SerialNumber: 0000:00:16.2
[ 3.214785] hub 3-0:1.0: USB hub found
[ 3.214802] hub 3-0:1.0: 4 ports detected
[ 3.230914] usbcore: registered new interface driver usb-storage
[ 3.232536] uhci_hcd: USB Universal Host Controller Interface driver
[ 3.234146] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.242109] usbcore: registered new interface driver usbhid
[ 3.242113] usbhid: USB HID core driver
[ 3.324278] device-mapper: uevent: version 1.0.3
[ 3.324375] device-mapper: ioctl: 4.30.0-ioctl (2014-12-22) initialised: dm-devel@redhat.com
[ 3.330287] Switched to clocksource tsc
[ 3.407024] JFS: nTxBlock = 8192, nTxLock = 65536
[ 3.412871] RPC: Registered named UNIX socket transport module.
[ 3.412873] RPC: Registered udp transport module.
[ 3.412873] RPC: Registered tcp transport module.
[ 3.412874] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 3.421607] zavl: module license 'CDDL' taints kernel.
[ 3.421614] Disabling lock debugging due to kernel taint
[ 3.423273] SPL: Loaded module v0.6.5-1
[ 3.455156] ZFS: Loaded module v0.6.5-1, ZFS pool version 5000, ZFS filesystem version 5
[ 3.462495] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
[ 3.462497] e1000: Copyright (c) 1999-2006 Intel Corporation.
[ 3.464837] pps_core: LinuxPPS API ver. 1 registered
[ 3.464839] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 3.465020] PTP clock support registered
[ 3.468023] Loading iSCSI transport class v2.0-870.
[ 3.506115] usb 1-5: new high-speed USB device number 2 using ehci-pci
[ 3.522137] usb 2-1: new high-speed USB device number 2 using ehci-pci
[ 3.647486] usb 1-5: New USB device found, idVendor=05e3, idProduct=0608
[ 3.647495] usb 1-5: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 3.647500] usb 1-5: Product: USB2.0 Hub
[ 3.648122] hub 1-5:1.0: USB hub found
[ 3.648448] hub 1-5:1.0: 4 ports detected
[ 3.674841] usb 2-1: New USB device found, idVendor=0cf3, idProduct=9271
[ 3.674843] usb 2-1: New USB device strings: Mfr=16, Product=32, SerialNumber=48
[ 3.674844] usb 2-1: Product: UB91C
[ 3.674845] usb 2-1: Manufacturer: ATHEROS
[ 3.674846] usb 2-1: SerialNumber: 12345
[ 3.812231] BTRFS: device label BTROOT devid 1 transid 21279 /dev/sda3
[ 3.813966] BTRFS info (device sda3): disk space caching is enabled
[ 3.871066] BTRFS: bdev /dev/sda3 errs: wr 0, rd 10, flush 0, corrupt 0, gen 0
[ 4.689353] usb 1-5-port3: Cannot enable. Maybe the USB cable is bad?
[ 5.173569] random: nonblocking pool is initialized
[ 5.520601] usb 1-5-port3: Cannot enable. Maybe the USB cable is bad?
[ 6.351903] usb 1-5-port3: Cannot enable. Maybe the USB cable is bad?
[ 7.170948] systemd-udevd[2358]: starting version 216
[ 7.187363] usb 1-5-port3: Cannot enable. Maybe the USB cable is bad?
[ 7.187596] usb 1-5-port3: unable to enumerate USB device
[ 7.570922] ohci-pci: OHCI PCI platform driver
[ 7.571044] ohci-pci 0000:00:12.0: OHCI PCI host controller
[ 7.571050] ohci-pci 0000:00:12.0: new USB bus registered, assigned bus number 4
[ 7.571073] ohci-pci 0000:00:12.0: irq 18, io mem 0xfe30a000
[ 7.605322] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 7.605328] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 5
[ 7.613814] rtc_cmos 00:04: RTC can wake from S4
[ 7.613998] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 7.614025] rtc_cmos 00:04: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 7.620566] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 7.620575] r8169 0000:01:00.0: can't disable ASPM; OS doesn't have ASPM control
[ 7.621024] r8169 0000:01:00.0 eth0: RTL8168evl/8111evl at 0xffffc900158aa000, 44:8a:5b:8f:f9:aa, XID 0c900800 IRQ 29
[ 7.621026] r8169 0000:01:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[ 7.630472] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 7.630474] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.630475] usb usb4: Product: OHCI PCI host controller
[ 7.630476] usb usb4: Manufacturer: Linux 4.0.5-gentoo-syd ohci_hcd
[ 7.630477] usb usb4: SerialNumber: 0000:00:12.0
[ 7.630595] hub 4-0:1.0: USB hub found
[ 7.630612] hub 4-0:1.0: 5 ports detected
[ 7.630831] ohci-pci 0000:00:13.0: OHCI PCI host controller
[ 7.630835] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 6
[ 7.630852] ohci-pci 0000:00:13.0: irq 18, io mem 0xfe308000
[ 7.641711] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input3
[ 7.641742] ACPI: Power Button [PWRB]
[ 7.641783] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[ 7.641810] ACPI: Power Button [PWRF]
[ 7.642136] ACPI: acpi_idle registered with cpuidle
[ 7.689308] [drm] Initialized drm 1.1.0 20060810
[ 7.690414] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 7.690416] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.690417] usb usb6: Product: OHCI PCI host controller
[ 7.690418] usb usb6: Manufacturer: Linux 4.0.5-gentoo-syd ohci_hcd
[ 7.690419] usb usb6: SerialNumber: 0000:00:13.0
[ 7.690541] hub 6-0:1.0: USB hub found
[ 7.690572] hub 6-0:1.0: 5 ports detected
[ 7.690804] ohci-pci 0000:00:14.5: OHCI PCI host controller
[ 7.690808] ohci-pci 0000:00:14.5: new USB bus registered, assigned bus number 7
[ 7.690829] ohci-pci 0000:00:14.5: irq 18, io mem 0xfe306000
[ 7.723800] xhci_hcd 0000:02:00.0: hcc params 0x014042cb hci version 0x96 quirks 0x00000004
[ 7.724137] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[ 7.724139] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.724140] usb usb5: Product: xHCI Host Controller
[ 7.724141] usb usb5: Manufacturer: Linux 4.0.5-gentoo-syd xhci-hcd
[ 7.724142] usb usb5: SerialNumber: 0000:02:00.0
[ 7.724299] hub 5-0:1.0: USB hub found
[ 7.724309] hub 5-0:1.0: 2 ports detected
[ 7.724652] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 7.724655] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 8
[ 7.727392] usb usb8: New USB device found, idVendor=1d6b, idProduct=0003
[ 7.727393] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.727394] usb usb8: Product: xHCI Host Controller
[ 7.727395] usb usb8: Manufacturer: Linux 4.0.5-gentoo-syd xhci-hcd
[ 7.727396] usb usb8: SerialNumber: 0000:02:00.0
[ 7.727505] hub 8-0:1.0: USB hub found
[ 7.727521] hub 8-0:1.0: 2 ports detected
[ 7.750415] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[ 7.750417] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.750418] usb usb7: Product: OHCI PCI host controller
[ 7.750419] usb usb7: Manufacturer: Linux 4.0.5-gentoo-syd ohci_hcd
[ 7.750420] usb usb7: SerialNumber: 0000:00:14.5
[ 7.750554] hub 7-0:1.0: USB hub found
[ 7.750570] hub 7-0:1.0: 2 ports detected
[ 7.750759] ohci-pci 0000:00:16.0: OHCI PCI host controller
[ 7.750764] ohci-pci 0000:00:16.0: new USB bus registered, assigned bus number 9
[ 7.750781] ohci-pci 0000:00:16.0: irq 18, io mem 0xfe305000
[ 7.810321] usb usb9: New USB device found, idVendor=1d6b, idProduct=0001
[ 7.810323] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.810324] usb usb9: Product: OHCI PCI host controller
[ 7.810325] usb usb9: Manufacturer: Linux 4.0.5-gentoo-syd ohci_hcd
[ 7.810326] usb usb9: SerialNumber: 0000:00:16.0
[ 7.810453] hub 9-0:1.0: USB hub found
[ 7.810501] hub 9-0:1.0: 4 ports detected
[ 7.811048] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
[ 7.811054] snd_hda_intel 0000:03:00.1: Disabling MSI
[ 7.811092] piix4_smbus 0000:00:14.0: Auxiliary SMBus Host Controller at 0xb20
[ 7.838891] acpi-cpufreq: overriding BIOS provided _PSD data
[ 7.840283] microcode: CPU0: patch_level=0x010000bf
[ 7.889414] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 7.904023] sound hdaudioC0D0: autoconfig for ALC892: line_outs=4 (0x14/0x15/0x16/0x17/0x0) type:line
[ 7.904027] sound hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 7.904028] sound hdaudioC0D0: hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[ 7.904029] sound hdaudioC0D0: mono: mono_out=0x0
[ 7.904030] sound hdaudioC0D0: dig-out=0x11/0x1e
[ 7.904031] sound hdaudioC0D0: inputs:
[ 7.904032] sound hdaudioC0D0: Front Mic=0x19
[ 7.904033] sound hdaudioC0D0: Rear Mic=0x18
[ 7.904034] sound hdaudioC0D0: Line=0x1a
[ 8.033389] microcode: CPU0: new patch_level=0x010000dc
[ 8.033433] microcode: CPU1: patch_level=0x010000bf
[ 8.033451] microcode: CPU1: new patch_level=0x010000dc
[ 8.033493] microcode: CPU2: patch_level=0x010000bf
[ 8.033499] microcode: CPU2: new patch_level=0x010000dc
[ 8.033509] microcode: CPU3: patch_level=0x010000bf
[ 8.033515] microcode: CPU3: new patch_level=0x010000dc
[ 8.033520] microcode: CPU4: patch_level=0x010000bf
[ 8.033524] microcode: CPU4: new patch_level=0x010000dc
[ 8.033531] microcode: CPU5: patch_level=0x010000bf
[ 8.033536] microcode: CPU5: new patch_level=0x010000dc
[ 8.033587] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 8.038236] usb 8-2: new SuperSpeed USB device number 2 using xhci_hcd
[ 8.060212] usb 8-2: New USB device found, idVendor=0480, idProduct=0200
[ 8.060214] usb 8-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[ 8.060215] usb 8-2: Product: External USB 3.0
[ 8.060216] usb 8-2: Manufacturer: TOSHIBA
[ 8.060217] usb 8-2: SerialNumber: 20141211001430C
[ 8.061233] usb-storage 8-2:1.0: USB Mass Storage device detected
[ 8.061458] scsi host6: usb-storage 8-2:1.0
[ 8.133872] usb 6-5: new full-speed USB device number 2 using ohci-pci
[ 8.145881] usb 9-4: new full-speed USB device number 2 using ohci-pci
[ 8.301741] usb 6-5: New USB device found, idVendor=12c9, idProduct=1001
[ 8.301750] usb 6-5: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[ 8.301754] usb 6-5: Product: 2.4GHz 2way RF Receiver
[ 8.313330] input: 2.4GHz 2way RF Receiver as /devices/pci0000:00/0000:00:13.0/usb6/6-5/6-5:1.0/0003:12C9:1001.0001/input/input6
[ 8.318744] usb 9-4: New USB device found, idVendor=046d, idProduct=c52b
[ 8.318752] usb 9-4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 8.318756] usb 9-4: Product: USB Receiver
[ 8.318760] usb 9-4: Manufacturer: Logitech
[ 8.327015] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:16.0/usb9/9-4/9-4:1.0/0003:046D:C52B.0002/input/input7
[ 8.365646] sound hdaudioC1D0: autoconfig for ID 14: line_outs=0 (0x0/0x0/0x0/0x0/0x0) type:line
[ 8.365655] sound hdaudioC1D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 8.365659] sound hdaudioC1D0: hp_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 8.365665] sound hdaudioC1D0: mono: mono_out=0x0
[ 8.365669] sound hdaudioC1D0: dig-out=0x5/0x0
[ 8.365672] sound hdaudioC1D0: inputs:
[ 8.366007] hid-generic 0003:12C9:1001.0001: input,hiddev0,hidraw0: USB HID v1.10 Mouse [2.4GHz 2way RF Receiver] on usb-0000:00:13.0-5/input0
[ 8.389643] sound hdaudioC1D1: autoconfig for ID 14: line_outs=0 (0x0/0x0/0x0/0x0/0x0) type:line
[ 8.389652] sound hdaudioC1D1: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 8.389657] sound hdaudioC1D1: hp_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 8.389661] sound hdaudioC1D1: mono: mono_out=0x0
[ 8.389664] sound hdaudioC1D1: dig-out=0x5/0x0
[ 8.389667] sound hdaudioC1D1: inputs:
[ 8.417610] sound hdaudioC1D2: autoconfig for ID 14: line_outs=0 (0x0/0x0/0x0/0x0/0x0) type:line
[ 8.417618] sound hdaudioC1D2: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 8.417623] sound hdaudioC1D2: hp_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 8.417626] sound hdaudioC1D2: mono: mono_out=0x0
[ 8.417630] sound hdaudioC1D2: dig-out=0x5/0x0
[ 8.417633] sound hdaudioC1D2: inputs:
[ 8.421868] hid-generic 0003:046D:C52B.0002: input,hidraw1: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-0000:00:16.0-4/input0
[ 8.427109] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:16.0/usb9/9-4/9-4:1.1/0003:046D:C52B.0003/input/input8
[ 8.445576] sound hdaudioC1D3: autoconfig for ID 14: line_outs=0 (0x0/0x0/0x0/0x0/0x0) type:line
[ 8.445584] sound hdaudioC1D3: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 8.445589] sound hdaudioC1D3: hp_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 8.445592] sound hdaudioC1D3: mono: mono_out=0x0
[ 8.445596] sound hdaudioC1D3: dig-out=0x5/0x0
[ 8.445598] sound hdaudioC1D3: inputs:
[ 8.481853] hid-generic 0003:046D:C52B.0003: input,hiddev0,hidraw2: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:16.0-4/input1
[ 8.488534] cfg80211: Calling CRDA to update world regulatory domain
[ 8.490735] hid-generic 0003:046D:C52B.0004: hiddev0,hidraw3: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:16.0-4/input2
[ 8.553438] snd_hda_intel 0000:03:00.1: control 0:0:0:HDMI Jack:0 is already present
[ 8.553442] sound hdaudioC1D1: cannot build controls for #1 (error -16)
[ 8.561471] snd_hda_intel 0000:03:00.1: control 0:0:0:HDMI Jack:0 is already present
[ 8.561480] sound hdaudioC1D2: cannot build controls for #2 (error -16)
[ 8.569468] snd_hda_intel 0000:03:00.1: control 0:0:0:HDMI Jack:0 is already present
[ 8.569477] sound hdaudioC1D3: cannot build controls for #3 (error -16)
[ 8.635132] vgaarb: device changed decodes: PCI:0000:03:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
[ 8.635414] NVLINK: Nvlink Core is being initialized, major device number 244
[ 8.635578] [drm] Initialized nvidia-drm 0.0.0 20150116 for 0000:03:00.0 on minor 0
[ 8.635582] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 355.11 Wed Aug 26 16:35:41 PDT 2015
[ 8.840923] usb 2-1: ath9k_htc: Firmware htc_9271.fw requested
[ 8.840973] usbcore: registered new interface driver ath9k_htc
[ 9.057816] scsi 6:0:0:0: Direct-Access TOSHIBA External USB 3.0 0 PQ: 0 ANSI: 6
[ 9.058007] sd 6:0:0:0: Attached scsi generic sg3 type 0
[ 9.061599] sd 6:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 9.062107] sd 6:0:0:0: [sdc] Write Protect is off
[ 9.062110] sd 6:0:0:0: [sdc] Mode Sense: 43 00 00 00
[ 9.062605] sd 6:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 9.134506] sdc: sdc1
[ 9.136042] sd 6:0:0:0: [sdc] Attached SCSI disk
[ 9.229866] usb 2-1: ath9k_htc: Transferred FW: htc_9271.fw, size: 51272
[ 9.253855] cfg80211: World regulatory domain updated:
[ 9.253857] cfg80211: DFS Master region: unset
[ 9.253857] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 9.253858] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 9.253859] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 9.253860] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 9.253861] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 9.253861] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 9.253862] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 9.253863] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 9.253863] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 9.391522] BTRFS: device label BOOT devid 1 transid 20 /dev/sda2
[ 9.466125] ath9k_htc 2-1:1.0: ath9k_htc: HTC initialized with 33 credits
[ 9.599206] NVRM: Your system is not currently configured to drive a VGA console
[ 9.599209] NVRM: on the primary VGA device. The NVIDIA Linux graphics driver
[ 9.599210] NVRM: requires the use of a text-mode VGA console. Use of other console
[ 9.599210] NVRM: drivers including, but not limited to, vesafb, may result in
[ 9.599211] NVRM: corruption and stability problems, and is not supported.
[ 9.863304] ath9k_htc 2-1:1.0: ath9k_htc: FW Version: 1.3
[ 9.863306] ath: EEPROM regdomain: 0x833a
[ 9.863307] ath: EEPROM indicates we should expect a country code
[ 9.863308] ath: doing EEPROM country->regdmn map search
[ 9.863308] ath: country maps to regdmn code: 0x37
[ 9.863309] ath: Country alpha2 being used: GB
[ 9.863310] ath: Regpair used: 0x37
[ 9.947797] ieee80211 phy0: Atheros AR9271 Rev:1
[ 9.947812] cfg80211: Calling CRDA for country: GB
[ 9.949529] cfg80211: Regulatory domain changed to country: GB
[ 9.949533] cfg80211: DFS Master region: unset
[ 9.949533] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 9.949534] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 9.949536] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 9.949537] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 9.949538] cfg80211: (5490000 KHz - 5710000 KHz @ 160000 KHz), (N/A, 2700 mBm), (0 s)
[ 9.949540] cfg80211: (57000000 KHz - 66000000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 11.064895] vboxdrv: Found 6 processor cores
[ 11.083412] vboxdrv: TSC mode is Invariant, tentative frequency 3300166188 Hz
[ 11.083413] vboxdrv: Successfully loaded version 5.0.4 (interface 0x00240000)
[ 11.146649] VBoxNetAdp: Successfully started.
[ 11.222031] BTRFS info (device sda3): enabling auto defrag
[ 11.222034] BTRFS info (device sda3): disk space caching is enabled
[ 11.420705] BTRFS info (device sda2): disk space caching is enabled
[ 14.809704] r8169 0000:01:00.0 eth0: link down
[ 491.475670] ata4.00: exception Emask 0x0 SAct 0x30000000 SErr 0x0 action 0x0
[ 491.475677] ata4.00: irq_stat 0x40000008
[ 491.475684] ata4.00: failed command: READ FPDMA QUEUED
[ 491.475697] ata4.00: cmd 60/20:e0:e0:6d:29/00:00:00:00:00/40 tag 28 ncq 16384 in
res 41/40:20:e8:6d:29/00:00:00:00:00/00 Emask 0x409 (media error) <F>
[ 491.475701] ata4.00: status: { DRDY ERR }
[ 491.475705] ata4.00: error: { UNC }
[ 491.476293] ata4.00: supports DRM functions and may not be fully accessible
[ 491.476963] ata4.00: supports DRM functions and may not be fully accessible
[ 491.477068] ata4.00: configured for UDMA/133
[ 491.477078] sd 3:0:0:0: [sda] tag#28 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x08
[ 491.477080] sd 3:0:0:0: [sda] tag#28 Sense Key : 0x3 [current] [descriptor]
[ 491.477081] sd 3:0:0:0: [sda] tag#28 ASC=0x11 ASCQ=0x4
[ 491.477083] sd 3:0:0:0: [sda] tag#28 CDB: opcode=0x28 28 00 00 29 6d e0 00 00 20 00
[ 491.477084] blk_update_request: I/O error, dev sda, sector 2715112
[ 491.477086] BTRFS: bdev /dev/sda3 errs: wr 0, rd 11, flush 0, corrupt 0, gen 0
[ 491.477104] ata4: EH complete
[ 491.495784] BTRFS: read error corrected: ino 1 off 854310912 (dev /dev/sda3 sector 1684960)
[ 491.517850] BTRFS: read error corrected: ino 1 off 854315008 (dev /dev/sda3 sector 1684968)
[ 491.575941] BTRFS: read error corrected: ino 1 off 854319104 (dev /dev/sda3 sector 1684976)
[ 491.917556] BTRFS: read error corrected: ino 1 off 854323200 (dev /dev/sda3 sector 1684984)
[ 504.128048] wlan0: authenticate with 6c:b0:ce:e2:78:d9
[ 504.426052] wlan0: send auth to 6c:b0:ce:e2:78:d9 (try 1/3)
[ 504.427934] wlan0: authenticated
[ 504.431203] wlan0: associate with 6c:b0:ce:e2:78:d9 (try 1/3)
[ 504.441713] wlan0: RX AssocResp from 6c:b0:ce:e2:78:d9 (capab=0x431 status=0 aid=1)
[ 504.448894] wlan0: associated
[ 548.113619] SPL: using hostid 0x00000000
[ 783.790151] ata4.00: exception Emask 0x0 SAct 0xc00000 SErr 0x0 action 0x0
[ 783.790158] ata4.00: irq_stat 0x40000008
[ 783.790166] ata4.00: failed command: READ FPDMA QUEUED
[ 783.790180] ata4.00: cmd 60/18:b0:80:b2:57/00:00:00:00:00/40 tag 22 ncq 12288 in
res 41/40:18:88:b2:57/00:00:00:00:00/00 Emask 0x409 (media error) <F>
[ 783.790184] ata4.00: status: { DRDY ERR }
[ 783.790187] ata4.00: error: { UNC }
[ 783.790774] ata4.00: supports DRM functions and may not be fully accessible
[ 783.791457] ata4.00: supports DRM functions and may not be fully accessible
[ 783.791558] ata4.00: configured for UDMA/133
[ 783.791569] sd 3:0:0:0: [sda] tag#22 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x08
[ 783.791571] sd 3:0:0:0: [sda] tag#22 Sense Key : 0x3 [current] [descriptor]
[ 783.791572] sd 3:0:0:0: [sda] tag#22 ASC=0x11 ASCQ=0x4
[ 783.791574] sd 3:0:0:0: [sda] tag#22 CDB: opcode=0x28 28 00 00 57 b2 80 00 00 18 00
[ 783.791575] blk_update_request: I/O error, dev sda, sector 5747336
[ 783.791577] BTRFS: bdev /dev/sda3 errs: wr 0, rd 12, flush 0, corrupt 0, gen 0
[ 783.791599] ata4: EH complete
[ 783.791610] BTRFS info (device sda3): csum failed ino 1876961 extent 2942644224 csum 2605917013 wanted 2638472761 mirror 0
[ 787.424818] ata4.00: exception Emask 0x0 SAct 0x1e0 SErr 0x0 action 0x0
[ 787.424821] ata4.00: irq_stat 0x40000008
[ 787.424824] ata4.00: failed command: READ FPDMA QUEUED
[ 787.424828] ata4.00: cmd 60/18:28:80:b2:57/00:00:00:00:00/40 tag 5 ncq 12288 in
res 41/40:18:88:b2:57/00:00:00:00:00/00 Emask 0x409 (media error) <F>
[ 787.424830] ata4.00: status: { DRDY ERR }
[ 787.424830] ata4.00: error: { UNC }
[ 787.425401] ata4.00: supports DRM functions and may not be fully accessible
[ 787.426122] ata4.00: supports DRM functions and may not be fully accessible
[ 787.426233] ata4.00: configured for UDMA/133
[ 787.426249] sd 3:0:0:0: [sda] tag#5 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x08
[ 787.426251] sd 3:0:0:0: [sda] tag#5 Sense Key : 0x3 [current] [descriptor]
[ 787.426253] sd 3:0:0:0: [sda] tag#5 ASC=0x11 ASCQ=0x4
[ 787.426255] sd 3:0:0:0: [sda] tag#5 CDB: opcode=0x28 28 00 00 57 b2 80 00 00 18 00
[ 787.426256] blk_update_request: I/O error, dev sda, sector 5747336
[ 787.426258] BTRFS: bdev /dev/sda3 errs: wr 0, rd 13, flush 0, corrupt 0, gen 0
[ 787.426284] ata4: EH complete
[ 787.426295] BTRFS info (device sda3): csum failed ino 1876961 extent 2942644224 csum 2079165314 wanted 2638472761 mirror 0
[ 1152.575852] ata4.00: exception Emask 0x0 SAct 0x4000 SErr 0x0 action 0x0
[ 1152.575858] ata4.00: irq_stat 0x40000008
[ 1152.575866] ata4.00: failed command: READ FPDMA QUEUED
[ 1152.575880] ata4.00: cmd 60/18:70:80:b2:57/00:00:00:00:00/40 tag 14 ncq 12288 in
res 41/40:18:88:b2:57/00:00:00:00:00/00 Emask 0x409 (media error) <F>
[ 1152.575884] ata4.00: status: { DRDY ERR }
[ 1152.575888] ata4.00: error: { UNC }
[ 1152.576509] ata4.00: supports DRM functions and may not be fully accessible
[ 1152.577189] ata4.00: supports DRM functions and may not be fully accessible
[ 1152.577294] ata4.00: configured for UDMA/133
[ 1152.577305] sd 3:0:0:0: [sda] tag#14 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x08
[ 1152.577307] sd 3:0:0:0: [sda] tag#14 Sense Key : 0x3 [current] [descriptor]
[ 1152.577308] sd 3:0:0:0: [sda] tag#14 ASC=0x11 ASCQ=0x4
[ 1152.577309] sd 3:0:0:0: [sda] tag#14 CDB: opcode=0x28 28 00 00 57 b2 80 00 00 18 00
[ 1152.577311] blk_update_request: I/O error, dev sda, sector 5747336
[ 1152.577313] BTRFS: bdev /dev/sda3 errs: wr 0, rd 14, flush 0, corrupt 0, gen 0
[ 1152.577338] ata4: EH complete
[ 1152.577347] BTRFS info (device sda3): csum failed ino 1876961 extent 2942644224 csum 2206149261 wanted 2638472761 mirror 0
[ 1505.416079] ata4.00: exception Emask 0x0 SAct 0x4 SErr 0x0 action 0x0
[ 1505.416085] ata4.00: irq_stat 0x40000008
[ 1505.416093] ata4.00: failed command: READ FPDMA QUEUED
[ 1505.416106] ata4.00: cmd 60/18:10:80:b2:57/00:00:00:00:00/40 tag 2 ncq 12288 in
res 41/40:18:88:b2:57/00:00:00:00:00/00 Emask 0x409 (media error) <F>
[ 1505.416111] ata4.00: status: { DRDY ERR }
[ 1505.416115] ata4.00: error: { UNC }
[ 1505.416721] ata4.00: supports DRM functions and may not be fully accessible
[ 1505.417409] ata4.00: supports DRM functions and may not be fully accessible
[ 1505.417511] ata4.00: configured for UDMA/133
[ 1505.417522] sd 3:0:0:0: [sda] tag#2 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x08
[ 1505.417524] sd 3:0:0:0: [sda] tag#2 Sense Key : 0x3 [current] [descriptor]
[ 1505.417525] sd 3:0:0:0: [sda] tag#2 ASC=0x11 ASCQ=0x4
[ 1505.417527] sd 3:0:0:0: [sda] tag#2 CDB: opcode=0x28 28 00 00 57 b2 80 00 00 18 00
[ 1505.417528] blk_update_request: I/O error, dev sda, sector 5747336
[ 1505.417530] BTRFS: bdev /dev/sda3 errs: wr 0, rd 15, flush 0, corrupt 0, gen 0
[ 1505.417554] ata4: EH complete
[ 1505.417562] BTRFS info (device sda3): csum failed ino 1876961 extent 2942644224 csum 2566472073 wanted 2638472761 mirror 0
[ 4089.997688] usb 1-5.3: new low-speed USB device number 7 using ehci-pci
[ 4090.069614] usb 1-5.3: device descriptor read/64, error -32
[ 4090.245418] usb 1-5.3: device descriptor read/64, error -32
[ 4090.421403] usb 1-5.3: new low-speed USB device number 8 using ehci-pci
[ 4090.493322] usb 1-5.3: device descriptor read/64, error -32
[ 4090.669138] usb 1-5.3: device descriptor read/64, error -32
[ 4090.844952] usb 1-5.3: new low-speed USB device number 9 using ehci-pci
[ 4091.252274] usb 1-5.3: device not accepting address 9, error -32
[ 4091.324574] usb 1-5.3: new low-speed USB device number 10 using ehci-pci
[ 4091.731791] usb 1-5.3: device not accepting address 10, error -32
[ 4091.732105] usb 1-5-port3: unable to enumerate USB device
[ 4818.140785] usb 1-5.3: new low-speed USB device number 11 using ehci-pci
[ 4818.212732] usb 1-5.3: device descriptor read/64, error -32
[ 4818.388520] usb 1-5.3: device descriptor read/64, error -32
[ 4818.564319] usb 1-5.3: new low-speed USB device number 12 using ehci-pci
[ 4818.636283] usb 1-5.3: device descriptor read/64, error -32
[ 4818.812220] usb 1-5.3: device descriptor read/64, error -32
[ 4818.988037] usb 1-5.3: new low-speed USB device number 13 using ehci-pci
[ 4819.395338] usb 1-5.3: device not accepting address 13, error -32
[ 4819.467618] usb 1-5.3: new low-speed USB device number 14 using ehci-pci
[ 4819.874894] usb 1-5.3: device not accepting address 14, error -32
[ 4819.875230] usb 1-5-port3: unable to enumerate USB device
[ 5436.385487] usb 1-5.3: new low-speed USB device number 15 using ehci-pci
[ 5436.785063] usb 1-5.3: new low-speed USB device number 16 using ehci-pci
[ 5436.856945] usb 1-5.3: device descriptor read/64, error -32
[ 5437.032759] usb 1-5.3: device descriptor read/64, error -32
[ 5437.208587] usb 1-5.3: new low-speed USB device number 17 using ehci-pci
[ 5437.280495] usb 1-5.3: device descriptor read/64, error -32
[ 5437.456473] usb 1-5.3: device descriptor read/64, error -32
[ 5437.632290] usb 1-5.3: new low-speed USB device number 18 using ehci-pci
[ 5443.042932] usb 1-5.3: device not accepting address 18, error -71
[ 5443.259091] usb 1-5.3: new low-speed USB device number 20 using ehci-pci
[ 5443.330969] usb 1-5.3: device descriptor read/64, error -32
[ 5443.506797] usb 1-5.3: device descriptor read/64, error -32
[ 5443.682605] usb 1-5.3: new low-speed USB device number 21 using ehci-pci
[ 5443.754522] usb 1-5.3: device descriptor read/64, error -32
[ 5443.930337] usb 1-5.3: device descriptor read/64, error -32
[ 5444.106351] usb 1-5.3: new low-speed USB device number 22 using ehci-pci
[ 5444.513605] usb 1-5.3: device not accepting address 22, error -32
[ 5444.585814] usb 1-5.3: new low-speed USB device number 23 using ehci-pci
[ 5444.993171] usb 1-5.3: device not accepting address 23, error -32
[ 5444.993508] usb 1-5-port3: unable to enumerate USB device
[ 5756.390834] cfg80211: Calling CRDA to update world regulatory domain
[ 5756.393743] cfg80211: World regulatory domain updated:
[ 5756.393747] cfg80211: DFS Master region: unset
[ 5756.393748] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 5756.393749] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 5756.393750] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 5756.393751] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 5756.393752] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 5756.393754] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 5756.393755] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 5756.393756] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 5756.393757] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 5757.736773] wlan0: authenticate with 6c:b0:ce:e2:78:d9
[ 5758.040858] wlan0: send auth to 6c:b0:ce:e2:78:d9 (try 1/3)
[ 5758.046838] wlan0: authenticated
[ 5758.047793] wlan0: associate with 6c:b0:ce:e2:78:d9 (try 1/3)
[ 5758.057151] wlan0: RX AssocResp from 6c:b0:ce:e2:78:d9 (capab=0x431 status=0 aid=1)
[ 5758.065048] wlan0: associated
[ 6888.239555] usb 1-5.3: new low-speed USB device number 24 using ehci-pci
[ 6888.311630] usb 1-5.3: device descriptor read/64, error -32
[ 6888.487446] usb 1-5.3: device descriptor read/64, error -32
[ 6888.663259] usb 1-5.3: new low-speed USB device number 25 using ehci-pci
[ 6888.735140] usb 1-5.3: device descriptor read/64, error -32
[ 6888.910966] usb 1-5.3: device descriptor read/64, error -32
[ 6889.086767] usb 1-5.3: new low-speed USB device number 26 using ehci-pci
[ 6889.494174] usb 1-5.3: device not accepting address 26, error -32
[ 6889.566464] usb 1-5.3: new low-speed USB device number 27 using ehci-pci
[ 6889.973738] usb 1-5.3: device not accepting address 27, error -32
[ 6889.974125] usb 1-5-port3: unable to enumerate USB device
[ 7805.188129] usb 1-5.3: new low-speed USB device number 28 using ehci-pci
[ 7805.260043] usb 1-5.3: device descriptor read/64, error -32
[ 7805.435859] usb 1-5.3: device descriptor read/64, error -32
[ 7805.611843] usb 1-5.3: new low-speed USB device number 29 using ehci-pci
[ 7805.683724] usb 1-5.3: device descriptor read/64, error -32
[ 7805.859580] usb 1-5.3: device descriptor read/64, error -32
[ 7806.035381] usb 1-5.3: new low-speed USB device number 30 using ehci-pci
[ 7806.442735] usb 1-5.3: device not accepting address 30, error -32
[ 7806.514972] usb 1-5.3: new low-speed USB device number 31 using ehci-pci
[ 7806.922287] usb 1-5.3: device not accepting address 31, error -32
[ 7806.922548] usb 1-5-port3: unable to enumerate USB device
[ 7946.181919] usb 1-5.3: new low-speed USB device number 32 using ehci-pci
[ 7946.253840] usb 1-5.3: device descriptor read/64, error -32
[ 7946.429637] usb 1-5.3: device descriptor read/64, error -32
[ 7946.605440] usb 1-5.3: new low-speed USB device number 33 using ehci-pci
[ 7946.677365] usb 1-5.3: device descriptor read/64, error -32
[ 7946.853307] usb 1-5.3: device descriptor read/64, error -32
[ 7947.029233] usb 1-5.3: new low-speed USB device number 34 using ehci-pci
[ 7947.436429] usb 1-5.3: device not accepting address 34, error -32
[ 7947.508632] usb 1-5.3: new low-speed USB device number 35 using ehci-pci
[ 7947.916472] usb 1-5.3: device not accepting address 35, error -32
[ 7947.916865] usb 1-5-port3: unable to enumerate USB device
[ 8268.104239] usb 1-5.3: new low-speed USB device number 36 using ehci-pci
[ 8268.176312] usb 1-5.3: device descriptor read/64, error -32
[ 8268.352251] usb 1-5.3: device descriptor read/64, error -32
[ 8268.527949] usb 1-5.3: new low-speed USB device number 37 using ehci-pci
[ 8268.599862] usb 1-5.3: device descriptor read/64, error -32
[ 8268.775802] usb 1-5.3: device descriptor read/64, error -32
[ 8268.951450] usb 1-5.3: new low-speed USB device number 38 using ehci-pci
[ 8269.358918] usb 1-5.3: device not accepting address 38, error -32
[ 8269.431083] usb 1-5.3: new low-speed USB device number 39 using ehci-pci
[ 8269.838477] usb 1-5.3: device not accepting address 39, error -32
[ 8269.838770] usb 1-5-port3: unable to enumerate USB device
[ 8735.476355] usb 1-5.3: new low-speed USB device number 40 using ehci-pci
[ 8735.548273] usb 1-5.3: device descriptor read/64, error -32
[ 8735.724258] usb 1-5.3: device descriptor read/64, error -32
[ 8735.900075] usb 1-5.3: new low-speed USB device number 41 using ehci-pci
[ 8735.971997] usb 1-5.3: device descriptor read/64, error -32
[ 8736.147804] usb 1-5.3: device descriptor read/64, error -32
[ 8736.323625] usb 1-5.3: new low-speed USB device number 42 using ehci-pci
[ 8736.730966] usb 1-5.3: device not accepting address 42, error -32
[ 8736.803243] usb 1-5.3: new low-speed USB device number 43 using ehci-pci
[ 8737.210519] usb 1-5.3: device not accepting address 43, error -32
[ 8737.210777] usb 1-5-port3: unable to enumerate USB device
[ 9023.706107] usb 1-5.3: new low-speed USB device number 44 using ehci-pci
[ 9023.778029] usb 1-5.3: device descriptor read/64, error -32
[ 9023.953842] usb 1-5.3: device descriptor read/64, error -32
[ 9024.129659] usb 1-5.3: new low-speed USB device number 45 using ehci-pci
[ 9024.201545] usb 1-5.3: device descriptor read/64, error -32
[ 9024.377520] usb 1-5.3: device descriptor read/64, error -32
[ 9024.553336] usb 1-5.3: new low-speed USB device number 46 using ehci-pci
[ 9024.960586] usb 1-5.3: device not accepting address 46, error -32
[ 9025.032835] usb 1-5.3: new low-speed USB device number 47 using ehci-pci
[ 9025.440139] usb 1-5.3: device not accepting address 47, error -32
[ 9025.440355] usb 1-5-port3: unable to enumerate USB device
[ 9401.976493] usb 1-5.3: new low-speed USB device number 48 using ehci-pci
[ 9402.048300] usb 1-5.3: device descriptor read/64, error -32
[ 9402.224183] usb 1-5.3: device descriptor read/64, error -32
[ 9402.399998] usb 1-5.3: new low-speed USB device number 49 using ehci-pci
[ 9402.471922] usb 1-5.3: device descriptor read/64, error -32
[ 9402.647901] usb 1-5.3: device descriptor read/64, error -32
[ 9402.823719] usb 1-5.3: new low-speed USB device number 50 using ehci-pci
[ 9403.231009] usb 1-5.3: device not accepting address 50, error -32
[ 9403.303179] usb 1-5.3: new low-speed USB device number 51 using ehci-pci
[ 9403.710562] usb 1-5.3: device not accepting address 51, error -32
[ 9403.710863] usb 1-5-port3: unable to enumerate USB device
[ 9887.483676] usb 1-5.3: new low-speed USB device number 52 using ehci-pci
[ 9887.555630] usb 1-5.3: device descriptor read/64, error -32
[ 9887.731580] usb 1-5.3: device descriptor read/64, error -32
[ 9887.907401] usb 1-5.3: new low-speed USB device number 53 using ehci-pci
[ 9887.979320] usb 1-5.3: device descriptor read/64, error -32
[ 9888.155132] usb 1-5.3: device descriptor read/64, error -32
[ 9888.330909] usb 1-5.3: new low-speed USB device number 54 using ehci-pci
[ 9888.738297] usb 1-5.3: device not accepting address 54, error -32
[ 9888.810573] usb 1-5.3: new low-speed USB device number 55 using ehci-pci
[ 9889.217847] usb 1-5.3: device not accepting address 55, error -32
[ 9889.218107] usb 1-5-port3: unable to enumerate USB device
[10286.618845] usb 1-5.3: new low-speed USB device number 57 using ehci-pci
[10286.690757] usb 1-5.3: device descriptor read/64, error -32
[10286.866610] usb 1-5.3: device descriptor read/64, error -32
[10287.042552] usb 1-5.3: new low-speed USB device number 58 using ehci-pci
[10287.114476] usb 1-5.3: device descriptor read/64, error -32
[10287.290258] usb 1-5.3: device descriptor read/64, error -32
[10287.466059] usb 1-5.3: new low-speed USB device number 59 using ehci-pci
[10287.873417] usb 1-5.3: device not accepting address 59, error -32
[10287.945720] usb 1-5.3: new low-speed USB device number 60 using ehci-pci
[10288.352979] usb 1-5.3: device not accepting address 60, error -32
[10288.353292] usb 1-5-port3: unable to enumerate USB device
[10896.655023] usb 1-5.3: new low-speed USB device number 62 using ehci-pci
[10896.726940] usb 1-5.3: device descriptor read/64, error -32
[10896.902919] usb 1-5.3: device descriptor read/64, error -32
[10897.078706] usb 1-5.3: new low-speed USB device number 63 using ehci-pci
[10897.150657] usb 1-5.3: device descriptor read/64, error -32
[10897.326473] usb 1-5.3: device descriptor read/64, error -32
[10897.502252] usb 1-5.3: new low-speed USB device number 64 using ehci-pci
[10897.909658] usb 1-5.3: device not accepting address 64, error -32
[10897.981905] usb 1-5.3: new low-speed USB device number 65 using ehci-pci
[10898.389187] usb 1-5.3: device not accepting address 65, error -32
[10898.389441] usb 1-5-port3: unable to enumerate USB device
[11834.636169] usb 1-5.3: new low-speed USB device number 66 using ehci-pci
[11834.708083] usb 1-5.3: device descriptor read/64, error -32
[11834.883915] usb 1-5.3: device descriptor read/64, error -32
[11835.059956] usb 1-5.3: new low-speed USB device number 67 using ehci-pci
[11835.131770] usb 1-5.3: device descriptor read/64, error -32
[11835.307643] usb 1-5.3: device descriptor read/64, error -32
[11835.483394] usb 1-5.3: new low-speed USB device number 68 using ehci-pci
[11835.890758] usb 1-5.3: device not accepting address 68, error -32
[11835.963051] usb 1-5.3: new low-speed USB device number 69 using ehci-pci
[11836.370314] usb 1-5.3: device not accepting address 69, error -32
[11836.370623] usb 1-5-port3: unable to enumerate USB device
[12904.983035] usb 1-5.3: new low-speed USB device number 70 using ehci-pci
[12905.054932] usb 1-5.3: device descriptor read/64, error -32
[12905.230768] usb 1-5.3: device descriptor read/64, error -32
[12905.406541] usb 1-5.3: new low-speed USB de
