[SOLVED]ndisw+INPROCOMM IPN 2220 no scan result on first try

[magowiz]

Hi,
I've got this wireless card on my laptop :

Code: Select all

02:02.0 Ethernet controller: Linksys, A Division of Cisco Systems [AirConn] INPROCOMM IPN 2220 Wireless LAN Adapter (rev 01)

I use ndiswrapper to make it work:

Code: Select all

# ndiswrapper -l
neti2220 : driver installed
	device (17FE:2220) present

If I connect with static configuration from /etc/conf.d/net to a specific AP I can connect to the Internet but before connecting my card hasn't got scan results :

Code: Select all

 # iwlist wlan0 scanning
wlan0     No scan results

so for example if I want to use NetworkManager or wicd I can't since they cannot find any network to join to.

AFTER I get connected with net.wlan0 initscript then I can get scan results :

Code: Select all

# iwlist wlan0 scanning
wlan0     Scan completed :
          Cell 01 - Address: 00:0F:A3:5B:D8:E8
                    ESSID:"PP"
                    Protocol:IEEE 802.11g
                    Mode:Managed
                    Frequency:2.417 GHz (Channel 2)
                    Quality:35/100  Signal level:-73 dBm  Noise level:-96 dBm
                    Encryption key:on
                    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
                              12 Mb/s; 24 Mb/s; 36 Mb/s; 9 Mb/s; 18 Mb/s
                              48 Mb/s; 54 Mb/s
                    Extra:bcn_int=100
                    Extra:atim=0
          Cell 02 - Address: 00:0F:A3:5B:DA:76
                    ESSID:"PP"
                    Protocol:IEEE 802.11g
                    Mode:Managed
                    Frequency:2.417 GHz (Channel 2)
                    Quality:39/100  Signal level:-71 dBm  Noise level:-96 dBm
                    Encryption key:on
                    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
                              12 Mb/s; 24 Mb/s; 36 Mb/s; 9 Mb/s; 18 Mb/s
                              48 Mb/s; 54 Mb/s
                    Extra:bcn_int=100
                    Extra:atim=0
          Cell 03 - Address: 00:14:6C:AA:73:28
                    ESSID:"wire"
                    Protocol:IEEE 802.11g
                    Mode:Managed
                    Frequency:2.437 GHz (Channel 6)
                    Quality:62/100  Signal level:-56 dBm  Noise level:-96 dBm
                    Encryption key:on
                    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 22 Mb/s
                              6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s
                              36 Mb/s; 48 Mb/s; 54 Mb/s
                    Extra:bcn_int=100
                    Extra:atim=0

What should it be ? Is there any native driver for my card ?

[magowiz]

I solved, it was a windows driver issue, before I was using the one provided by acer (my laptop manufacter) , I switched to a driver provided by toshiba that has a laptop with my same wlan nic , the working one can be found here : http://driverscollection.com/?file_id=32880