Hi!
I can't boot system for installation. Once it hits sata_sx4 - system stops for 15 minuts, then continues to boot. When it gets to "configuring to use with udev" - it hangs! Any ideas?
Hardware:
ASUS P4C800 with 1024 RAM with P4-3.0Ghz HT
promise s150 sx4-m raid 5 controller
4x seagate 400GB sata hdds
Thanks!
promise S150 SX4-M
Message
I booted up system with "nosata" option to kernel.
That's what I got:
System hanged here!
Mike
That's what I got:
Code: Select all
livecd ~ # lspci
0000:00:00.0 Host bridge: Intel Corporation 82875P/E7210 Memory Controller Hub (rev 02)
0000:00:01.0 PCI bridge: Intel Corporation 82875P Processor to AGP Controller (rev 02)
0000:00:03.0 PCI bridge: Intel Corporation 82875P/E7210 Processor to PCI to CSA Bridge (rev 02)
0000:00:1d.0 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1 (rev 02)
0000:00:1d.1 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2 (rev 02)
0000:00:1d.2 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI #3 (rev 02)
0000:00:1d.3 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #4 (rev 02)
0000:00:1d.7 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller (rev 02)
0000:00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev c2)
0000:00:1f.0 ISA bridge: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge (rev 02)
0000:00:1f.1 IDE interface: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE Controller (rev 02)
0000:00:1f.3 SMBus: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus Controller (rev 02)
0000:00:1f.5 Multimedia audio controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) AC'97 Audio Controller (rev 02)
0000:01:00.0 VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX 440 AGP 8x] (rev c1)
0000:02:01.0 Ethernet controller: Intel Corporation 82547EI Gigabit Ethernet Controller (LOM)
0000:03:03.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 80)
0000:03:0a.0 RAID bus controller: Promise Technology, Inc. PDC20621 [SATA150 SX4] 4 Channel IDE RAID Controller (rev 01)
Code: Select all
livecd ~ # dmesg
Linux version 2.6.12-gentoo-r6 (root@poseidon) (gcc version 3.3.5-20050130 (Gentoo 3.3.5.20050130-r1, ssp-3.3.5.20050130-1, pie-8.7.7.1)) #1 SMP Tue Aug 2 16:32:16 UTC 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003ff30000 (usable)
BIOS-e820: 000000003ff30000 - 000000003ff40000 (ACPI data)
BIOS-e820: 000000003ff40000 - 000000003fff0000 (ACPI NVS)
BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved)
BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000ff780
On node 0 totalpages: 261936
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 32560 pages, LIFO batch:15
DMI 2.3 present.
ACPI: RSDP (v000 ACPIAM ) @ 0x000f9e30
ACPI: RSDT (v001 A M I OEMRSDT 0x09000424 MSFT 0x00000097) @ 0x3ff30000
ACPI: FADT (v002 A M I OEMFACP 0x09000424 MSFT 0x00000097) @ 0x3ff30200
ACPI: MADT (v001 A M I OEMAPIC 0x09000424 MSFT 0x00000097) @ 0x3ff30390
ACPI: OEMB (v001 A M I OEMBIOS 0x09000424 MSFT 0x00000097) @ 0x3ff40040
ACPI: DSDT (v001 P4CED P4CED105 0x00000105 INTL 0x02002026) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:2 APIC version 20
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 40000000:bfb80000)
Built 1 zonelists
Kernel command line: initrd=gentoo.igz root=/dev/ram0 init=/linuxrc looptype=squashfs loop=/livecd.squashfs dokeymap cdroot BOOT_IMAGE=gentoo nosata
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
CPU 0 irqstacks, hard=c0409000 soft=c0401000
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 2998.857 MHz processor.
Using tsc for high-res timesource
Speakup v-2.00 CVS: Wed Mar 2 20:22:02 EST 2005 : initialized
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1017760k/1047744k available (2263k kernel code, 29104k reserved, 596k data, 192k init, 130240k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 5914.62 BogoMIPS (lpj=2957312)
Mount-cache hash table entries: 512
Couldn't initialize miscdevice /dev/synth.
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09
Booting processor 1/1 eip 2000
CPU 1 irqstacks, hard=c040a000 soft=c0402000
Initializing CPU#1
Calibrating delay loop... 5980.16 BogoMIPS (lpj=2990080)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000
CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09
Total of 2 processors activated (11894.78 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
CPU0 attaching sched-domain:
domain 0: span 03
groups: 01 02
domain 1: span 03
groups: 03
CPU1 attaching sched-domain:
domain 0: span 03
groups: 02 01
domain 1: span 03
groups: 03
checking if image is initramfs... it is
Freeing initrd memory: 16420k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=3
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050309
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:09: ioport range 0x680-0x6ff has been reserved
pnp: 00:09: ioport range 0x290-0x297 has been reserved
highmem bounce pool size: 64 pages
inotify device minor=63
Squashfs 2.1 (released 2004/12/10) (C) 2002-2004 Phillip Lougher
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PNP: PS/2 controller doesn't have AUX irq; using default 0xc
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 112
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
mice: PS/2 mouse device common for all mice
io scheduler noop registered
io scheduler deadline registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH5: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:pio, hdb:DMA
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
input: AT Translated Set 2 keyboard on isa0060/serio0
logips2pp: Detected unknown logitech mouse model 0
input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
hdb: LITE-ON DVDRW SOHW-1633S, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hdb: ATAPI 63X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
EISA: Probing bus 0 at eisa.0
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 64Kbytes
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 1
NET: Registered protocol family 17
Starting balanced_irq
Freeing unused kernel memory: 192k freed
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfebfbc00
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
USB Universal Host Controller Interface driver v2.2
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000ef00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000ef20
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ef40
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000ef80
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
sl811: driver sl811-hcd, 19 May 2005
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1250 $ Ben Collins <bcollins@debian.org>
ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 20 (level, low) -> IRQ 20
PCI: Via IRQ fixup for 0000:03:03.0, from 10 to 4
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[20] MMIO=[feafe800-feafefff] Max Packet=[2048]
sbp2: $Rev: 1219 $ Ben Collins <bcollins@debian.org>
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e0180000a8d6af]
ReiserFS: hdb: warning: sh-2021: reiserfs_fill_super: can not find reiserfs on hdb
VFS: Can't find ext3 filesystem on dev hdb.
VFS: Can't find an ext2 filesystem on dev hdb.
SQUASHFS error: Can't find a SQUASHFS superblock on hdb
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev hdb.
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
pnp: Device 00:08 disabled.
Intel(R) PRO/1000 Network Driver - version 6.0.54-k2
Copyright (c) 1999-2004 Intel Corporation.
ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:02:01.0 to 64
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
Intel(R) PRO/1000 Network Driver - version 6.0.54-k2
Copyright (c) 1999-2004 Intel Corporation.
ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:02:01.0 to 64
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
libata version 1.11 loaded.
sata_sx4 version 0.7
ACPI: PCI Interrupt 0000:03:0a.0[A] -> GSI 22 (level, low) -> IRQ 22
Local DIMM ECC Enabled
e1000: eth0: e1000_watchdog_task: NIC Link is Up 100 Mbps Full Duplex
Real Time Clock Driver v1.12
input: PC Speaker
e1000: eth0: e1000_watchdog_task: NIC Link is Up 100 Mbps Full Duplex
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
pnp: Device 00:08 activated.
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
ata1: SATA max UDMA/133 cmd 0xF8A40200 ctl 0xF8A40238 bmdma 0x0 irq 22
ata2: SATA max UDMA/133 cmd 0xF8A40280 ctl 0xF8A402B8 bmdma 0x0 irq 22
ata3: SATA max UDMA/133 cmd 0xF8A40300 ctl 0xF8A40338 bmdma 0x0 irq 22
ata4: SATA max UDMA/133 cmd 0xF8A40380 ctl 0xF8A403B8 bmdma 0x0 irq 22
ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:207f
ata1: dev 0 ATA, max UDMA/133, 781422768 sectors: lba48
ata1: dev 0 configured for UDMA/133
scsi0 : sata_sx4
ata2: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:207f
ata2: dev 0 ATA, max UDMA/133, 781422768 sectors: lba48
ata2: dev 0 configured for UDMA/133
scsi1 : sata_sx4
ata3: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:207f
ata3: dev 0 ATA, max UDMA/133, 781422768 sectors: lba48
ata3: dev 0 configured for UDMA/133
scsi2 : sata_sx4
ata4: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:207f
ata4: dev 0 ATA, max UDMA/133, 781422768 sectors: lba48
ata4: dev 0 configured for UDMA/133
scsi3 : sata_sx4
Vendor: ATA Model: ST3400832AS Rev: 3.01
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 781422768 512-byte hdwr sectors (400088 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 781422768 512-byte hdwr sectors (400088 MB)
SCSI device sda: drive cache: write back
sda: unknown partition table
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Vendor: ATA Model: ST3400832AS Rev: 3.01
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdb: 781422768 512-byte hdwr sectors (400088 MB)
SCSI device sdb: drive cache: write back
SCSI device sdb: 781422768 512-byte hdwr sectors (400088 MB)
SCSI device sdb: drive cache: write back
sdb:<3>ata2: command timeout
ata2: status=0x51 { DriveReady SeekComplete Error }
ata2: called with no error (51)!
SCSI error : <1 0 0 0> return code = 0x8000002
sdb: Current: sense key=0x3
ASC=0x11 ASCQ=0x4
end_request: I/O error, dev sdb, sector 0
Buffer I/O error on device sdb, logical block 0
ata2: command timeout
ata2: status=0x51 { DriveReady SeekComplete Error }
ata2: called with no error (51)!
SCSI error : <1 0 0 0> return code = 0x8000002
sdb: Current: sense key=0x3
ASC=0x11 ASCQ=0x4
end_request: I/O error, dev sdb, sector 0
Buffer I/O error on device sdb, logical block 0
ldm_validate_partition_table(): Disk read failed.
ata2: command timeout
ata2: status=0x51 { DriveReady SeekComplete Error }
ata2: called with no error (51)!
SCSI error : <1 0 0 0> return code = 0x8000002
sdb: Current: sense key=0x3
ASC=0x11 ASCQ=0x4
end_request: I/O error, dev sdb, sector 0
Buffer I/O error on device sdb, logical block 0
unable to read partition table
Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
Vendor: ATA Model: ST3400832AS Rev: 3.01
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdc: 781422768 512-byte hdwr sectors (400088 MB)
SCSI device sdc: drive cache: write back
SCSI device sdc: 781422768 512-byte hdwr sectors (400088 MB)
SCSI device sdc: drive cache: write back
sdc:<3>ata3: command timeout
ata3: status=0x51 { DriveReady SeekComplete Error }
ata3: called with no error (51)!
SCSI error : <2 0 0 0> return code = 0x8000002
sdc: Current: sense key=0x3
ASC=0x11 ASCQ=0x4
end_request: I/O error, dev sdc, sector 0
Buffer I/O error on device sdc, logical block 0
ata3: command timeout
ata3: status=0x51 { DriveReady SeekComplete Error }
ata3: called with no error (51)!
SCSI error : <2 0 0 0> return code = 0x8000002
sdc: Current: sense key=0x3
ASC=0x11 ASCQ=0x4
end_request: I/O error, dev sdc, sector 0
Buffer I/O error on device sdc, logical block 0
ldm_validate_partition_table(): Disk read failed.
ata3: command timeout
ata3: status=0x51 { DriveReady SeekComplete Error }
ata3: called with no error (51)!
SCSI error : <2 0 0 0> return code = 0x8000002
sdc: Current: sense key=0x3
ASC=0x11 ASCQ=0x4
end_request: I/O error, dev sdc, sector 0
Buffer I/O error on device sdc, logical block 0
unable to read partition table
Attached scsi disk sdc at scsi2, channel 0, id 0, lun 0
Vendor: ATA Model: ST3400832AS Rev: 3.01
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdd: 781422768 512-byte hdwr sectors (400088 MB)
SCSI device sdd: drive cache: write back
SCSI device sdd: 781422768 512-byte hdwr sectors (400088 MB)
SCSI device sdd: drive cache: write back
sdd:<3>ata4: command timeout
ata4: status=0x51 { DriveReady SeekComplete Error }
ata4: called with no error (51)!
SCSI error : <3 0 0 0> return code = 0x8000002
sdd: Current: sense key=0x3
ASC=0x11 ASCQ=0x4
end_request: I/O error, dev sdd, sector 0
Buffer I/O error on device sdd, logical block 0
ata4: command timeout
ata4: status=0x51 { DriveReady SeekComplete Error }
ata4: called with no error (51)!
SCSI error : <3 0 0 0> return code = 0x8000002
sdd: Current: sense key=0x3
ASC=0x11 ASCQ=0x4
end_request: I/O error, dev sdd, sector 0
Buffer I/O error on device sdd, logical block 0
ldm_validate_partition_table(): Disk read failed.
ata4: command timeout
ata4: status=0x51 { DriveReady SeekComplete Error }
ata4: called with no error (51)!
SCSI error : <3 0 0 0> return code = 0x8000002
sdd: Current: sense key=0x3
ASC=0x11 ASCQ=0x4
end_request: I/O error, dev sdd, sector 0
Buffer I/O error on device sdd, logical block 0
unable to read partition table
Attached scsi disk sdd at scsi3, channel 0, id 0, lun 0
NET: Registered protocol family 10
Disabled Privacy Extensions on device c03b6720(lo)
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
Code: Select all
livecd ~ # ls /dev/sd*
/dev/sda /dev/sdb /dev/sdc /dev/sdd
livecd ~ # fdisk
Usage: fdisk [-l] [-b SSZ] [-u] device
E.g.: fdisk /dev/hda (for the first IDE disk)
or: fdisk /dev/sdc (for the third SCSI disk)
or: fdisk /dev/eda (for the first PS/2 ESDI drive)
or: fdisk /dev/rd/c0d0 or: fdisk /dev/ida/c0d0 (for RAID devices)
...
livecd ~ # fdisk /dev/sda
Mike
