I just updated my system and it is now using kernel 2.6.14-gentoo-r5. I have also re-built nvidia-kernel and nvidia-glx. The gdm login screen looks fine; however, after I login, it would kick me out immediately. There appeared to be a few message boxes, but I got kicked out so quick couldn't make out anything.
BTW. when I was emerging nvidia-glx, it had a QA warning about not running well on certain execute stack. Once again, my eyes are too slow for the message. Could this be related?
Has anyone seen this problem? If so, any solutions? Any help is appreciated. Thanks!
-- G5
nvidia problem
Message
- thoffmeyer
- Apprentice
- Posts: 208
- Joined: Sun Apr 11, 2004 3:46 am
- Location: GMT -5 Hours
okay, here it goes.
and here is the xorg.log:
and xorg.conf
Code: Select all
Linux version 2.6.14-gentoo-r5 (root@amd) (gcc version 3.4.4 (Gentoo 3.4.4-r1, ssp-3.4.4-1.0, pie-8.7.8)) #1 SMP PREEMPT Thu Jan 5 11:02:10 EST 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003bff0000 (usable)
BIOS-e820: 000000003bff0000 - 000000003bff3000 (ACPI NVS)
BIOS-e820: 000000003bff3000 - 000000003c000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
63MB HIGHMEM available.
896MB LOWMEM available.
On node 0 totalpages: 245744
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 16368 pages, LIFO batch:7
DMI 2.3 present.
ACPI: RSDP (v000 FIC ) @ 0x000f7260
ACPI: RSDT (v001 FIC AU31 0x42302e31 AWRD 0x00000000) @ 0x3bff3000
ACPI: FADT (v001 FIC AU31 0x42302e31 AWRD 0x00000000) @ 0x3bff3040
ACPI: MADT (v001 FIC AU31 0x42302e31 AWRD 0x00000000) @ 0x3bff6c80
ACPI: DSDT (v001 FIC AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:10 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 3c000000:c2c00000)
Built 1 zonelists
Kernel command line: root=/dev/ram0 init=/linuxrc ramdisk=8192 real_root=/dev/hda4 udev
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
CPU 0 irqstacks, hard=c049f000 soft=c0497000
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 2088.391 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 967820k/982976k available (2694k kernel code, 14488k reserved, 738k data, 216k init, 65472k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 4181.07 BogoMIPS (lpj=8362156)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000020 00000000 00000000 00000000
mtrr: v2.0 (20020519)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: AMD Athlon(tm) XP 2800+ stepping 00
Total of 1 processors activated (4181.07 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=0 pin2=-1
Brought up 1 CPUs
checking if image is initramfs...softlockup thread 0 started up.
it is
Freeing initrd memory: 1713k freed
NET: Registered protocol family 16
EISA bus registered
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfbcb0, last bus=2
PCI: Using configuration type 1
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: nForce2 C1 Halt Disconnect fixup
Boot video device is 0000:02:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs *0 20)
ACPI: PCI Interrupt Link [LNK2] (IRQs *0 20), disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs *0 20), disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs *0 20), disabled.
ACPI: PCI Interrupt Link [LNK5] (IRQs *0 20)
ACPI: PCI Interrupt Link [LUBA] (IRQs *0 20)
ACPI: PCI Interrupt Link [LUBB] (IRQs *0 20)
ACPI: PCI Interrupt Link [LMAC] (IRQs *0 20)
ACPI: PCI Interrupt Link [LACI] (IRQs *0 20)
ACPI: PCI Interrupt Link [LSMB] (IRQs *0 20)
ACPI: PCI Interrupt Link [LUB2] (IRQs *0 20)
ACPI: PCI Interrupt Link [LFIR] (IRQs *0 20), disabled.
ACPI: PCI Interrupt Link [LIDE] (IRQs *0 20), disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs *17), disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs *18), disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs *19), disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs *23), disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:00: ioport range 0x4000-0x407f could not be reserved
pnp: 00:00: ioport range 0x4080-0x40ff has been reserved
pnp: 00:00: ioport range 0x4400-0x447f has been reserved
pnp: 00:00: ioport range 0x4480-0x44ff could not be reserved
pnp: 00:00: ioport range 0x4200-0x427f has been reserved
pnp: 00:00: ioport range 0x4280-0x42ff has been reserved
pnp: 00:01: ioport range 0x5000-0x503f has been reserved
pnp: 00:01: ioport range 0x5100-0x513f has been reserved
PCI: Bridge: 0000:00:08.0
IO window: c000-cfff
MEM window: ec000000-ecffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
IO window: disabled.
MEM window: ea000000-ebffffff
PREFETCH window: e0000000-e7ffffff
PCI: Setting latency timer of device 0000:00:08.0 to 64
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
vesafb: NVIDIA Corporation, CR17 Board, Chip Rev A3 (OEM: NVIDIA)
vesafb: VBE version: 3.0
vesafb: VBIOS/hardware supports DDC2 transfers
vesafb: monitor limits: vf = 75 Hz, hf = 82 kHz, clk = 140 MHz
vesafb: scrolling: redraw
Console: switching to colour frame buffer device 80x30
vesafb: framebuffer at 0xe0000000, mapped to 0xf8880000, using 24576k, total 65536k
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 0) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC1] -> GSI 16 (level, high) -> IRQ 16
ttyS1 at I/O 0xc028 (irq = 16) is a 8250
ttyS2 at I/O 0xc040 (irq = 16) is a 8250
ttyS3 at I/O 0xc050 (irq = 16) is a 8250
Couldn't register serial port 0000:01:08.0: -28
mice: PS/2 mouse device common for all mice
io scheduler noop registered
io scheduler deadline registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE2: IDE controller at PCI slot 0000:00:09.0
NFORCE2: chipset revision 162
NFORCE2: not 100% native mode: will probe irqs later
NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
input: AT Translated Set 2 keyboard on isa0060/serio0
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
hda: WDC WD1200AB-22DYA0, ATA DISK drive
hdb: ST3120026A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: JLMS XJ-HD166S, ATAPI CD/DVD-ROM drive
hdd: SONY DVD RW DRU-720A, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3 < hda5 hda6 hda7 hda8 hda9 > hda4
hdb: max request size: 1024KiB
hdb: 234441648 sectors (120034 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100)
hdb: cache flushes supported
hdb: hdb1 < hdb5 hdb6 hdb7 hdb8 hdb9 hdb10 >
hdc: ATAPI 48X DVD-ROM drive, 512kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
EISA: Probing bus 0 at eisa.0
Cannot allocate resource for EISA slot 4
Cannot allocate resource for EISA slot 5
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
Freeing unused kernel memory: 216k freed
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [APCL] -> GSI 22 (level, high) -> IRQ 17
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: EHCI Host Controller
ehci_hcd 0000:00:02.2: debug port 1
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.2: irq 17, io mem 0xed005000
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: park 0
ehci_hcd 0000:00:02.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
USB Universal Host Controller Interface driver v2.3
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 21 (level, high) -> IRQ 18
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.0: irq 18, io mem 0xed003000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ACPI: PCI Interrupt Link [APCG] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCG] -> GSI 20 (level, high) -> IRQ 19
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: OHCI Host Controller
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:02.1: irq 19, io mem 0xed004000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
sl811: driver sl811-hcd, 19 May 2005
ieee1394: Initialized config rom entry `ip1394'
sbp2: $Rev: 1306 $ Ben Collins <bcollins@debian.org>
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
libata version 1.12 loaded.
usb 3-3: new full speed USB device using ohci_hcd and address 2
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
ReiserFS: hda4: warning: sh-2021: reiserfs_fill_super: can not find reiserfs on hda4
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 2104472k swap on /dev/hdb5. Priority:-1 extents:1 across:2104472k
Vendor: eM Model: Bay Reader Rev: 1.00
Type: Direct-Access ANSI SCSI revision: 00
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
usb-storage: device scan complete
EXT3 FS on hda4, internal journal
NTFS driver 2.1.24 [Flags: R/O MODULE].
NTFS volume version 3.1.
NTFS volume version 3.1.
NTFS volume version 3.1.
NTFS volume version 3.1.
NTFS volume version 3.1.
NTFS volume version 3.1.
NTFS volume version 3.1.
NTFS volume version 3.1.
NTFS volume version 3.1.
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected NVIDIA nForce2 chipset
agpgart: AGP aperture is 32M @ 0xe8000000
i2c_adapter i2c-0: nForce2 SMBus adapter at 0x5000
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x5100
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.41.
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [APCH] -> GSI 22 (level, high) -> IRQ 17
PCI: Setting latency timer of device 0000:00:04.0 to 64
eth0: forcedeth.c: subsystem: 01509:904d bound to 0000:00:04.0
ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [APCJ] -> GSI 21 (level, high) -> IRQ 18
PCI: Setting latency timer of device 0000:00:06.0 to 64
intel8x0_measure_ac97_clock: measured 56845 usecs
intel8x0: clocking to 47453
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt Link [APC5] enabled at IRQ 16
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [APC5] -> GSI 16 (level, high) -> IRQ 16
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-6629 Wed Nov 3 13:12:51 PST 2004
Real Time Clock Driver v1.12
input: PC Speaker
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
and here is the xorg.log:
Code: Select all
amd log # cat Xorg.0.log
X Window System Version 6.8.2
Release Date: 9 February 2005
X Protocol Version 11, Revision 0, Release 6.8.2
Build Operating System: Linux 2.6.14-gentoo-r2 i686 [ELF]
Current Operating System: Linux amd 2.6.14-gentoo-r5 #1 SMP PREEMPT Thu Jan 5 11:02:10 EST 2006 i686
Build Date: 02 December 2005
Before reporting problems, check http://wiki.X.Org
to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Thu Jan 5 21:40:26 2006
(==) Using config file: "/etc/X11/xorg.conf"
(==) ServerLayout "Main Layout"
(**) |-->Screen "Screen0" (0)
(**) | |-->Monitor "ViewSonic VA720"
(**) | |-->Device "nVidia GeForce"
(**) |-->Input Device "Mouse1"
(**) |-->Input Device "Keyboard1"
(WW) The directory "/usr/share/fonts/CID/" does not exist.
Entry deleted from font path.
(WW) The directory "/usr/share/fonts/Speedo/" does not exist.
Entry deleted from font path.
(**) FontPath set to "/usr/share/fonts/local/,/usr/share/fonts/misc/,/usr/share/fonts/75dpi/:unscaled,/usr/share/fonts/100dpi/:unscaled,/usr/share/fonts/Type1/,/usr/share/fonts/TTF/,/usr/share/fonts/75dpi/,/usr/share/fonts/100dpi/,/usr/share/fonts/arphicfonts/,/usr/share/fonts/cjkuni-fonts/,/usr/share/fonts/corefonts/,/usr/share/fonts/cronyx/,/usr/share/fonts/cyrillic/,/usr/share/fonts/default/,/usr/share/fonts/freefont/,/usr/share/fonts/hkscs-ming/,/usr/share/fonts/intlfonts/,/usr/share/fonts/terminus/,/usr/share/fonts/twmoefonts/,/usr/share/fonts/ukr/,/usr/share/fonts/util/,/usr/share/fonts/zh-kcfonts/"
(**) RgbPath set to "/usr/lib/X11/rgb"
(==) ModulePath set to "/usr/lib/modules"
(**) Option "BlankTime" "10"
(**) Option "StandbyTime" "20"
(**) Option "SuspendTime" "30"
(**) Option "OffTime" "60"
(WW) Open APM failed (/dev/apm_bios) (No such file or directory)
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.2
X.Org Video Driver: 0.7
X.Org XInput driver : 0.4
X.Org Server Extension : 0.2
X.Org Font Renderer : 0.4
(II) Loader running on linux
(II) LoadModule: "bitmap"
(II) Loading /usr/lib/modules/fonts/libbitmap.a
(II) Module bitmap: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.0
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.4
(II) Loading font Bitmap
(II) LoadModule: "pcidata"
(II) Loading /usr/lib/modules/libpcidata.a
(II) Module pcidata: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.0
ABI class: X.Org Video Driver, version 0.7
(++) using VT number 7
(II) PCI: PCI scan (all values are in hex)
(II) PCI: 00:00:0: chip 10de,01e0 card 0000,0000 rev a2 class 06,00,00 hdr 80
(II) PCI: 00:00:1: chip 10de,01eb card 1509,904d rev a2 class 05,00,00 hdr 80
(II) PCI: 00:00:2: chip 10de,01ee card 1509,904d rev a2 class 05,00,00 hdr 80
(II) PCI: 00:00:3: chip 10de,01ed card 1509,904d rev a2 class 05,00,00 hdr 80
(II) PCI: 00:00:4: chip 10de,01ec card 1509,904d rev a2 class 05,00,00 hdr 80
(II) PCI: 00:00:5: chip 10de,01ef card 1509,904d rev a2 class 05,00,00 hdr 80
(II) PCI: 00:01:0: chip 10de,0060 card 1509,904d rev a4 class 06,01,00 hdr 80
(II) PCI: 00:01:1: chip 10de,0064 card 1509,904d rev a2 class 0c,05,00 hdr 80
(II) PCI: 00:02:0: chip 10de,0067 card 1509,904d rev a4 class 0c,03,10 hdr 80
(II) PCI: 00:02:1: chip 10de,0067 card 1509,904d rev a4 class 0c,03,10 hdr 80
(II) PCI: 00:02:2: chip 10de,0068 card 1509,904d rev a4 class 0c,03,20 hdr 80
(II) PCI: 00:04:0: chip 10de,0066 card 1509,904d rev a1 class 02,00,00 hdr 00
(II) PCI: 00:06:0: chip 10de,006a card 1509,904d rev a1 class 04,01,00 hdr 00
(II) PCI: 00:08:0: chip 10de,006c card 0000,0000 rev a3 class 06,04,00 hdr 01
(II) PCI: 00:09:0: chip 10de,0065 card 1509,904d rev a2 class 01,01,8a hdr 00
(II) PCI: 00:1e:0: chip 10de,01e8 card 0000,0000 rev a2 class 06,04,00 hdr 01
(II) PCI: 01:08:0: chip 10b9,5459 card 14fe,9100 rev 00 class 07,03,00 hdr 00
(II) PCI: 02:00:0: chip 10de,01f0 card 1509,904d rev a3 class 03,00,00 hdr 00
(II) PCI: End of PCI scan
(II) Host-to-PCI bridge:
(II) Bus 0: bridge is at (0:0:0), (0,0,2), BCTRL: 0x0008 (VGA_EN is set)
(II) Bus 0 I/O range:
[0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) Bus 0 non-prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus 0 prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
(II) PCI-to-ISA bridge:
(II) Bus -1: bridge is at (0:1:0), (0,-1,-1), BCTRL: 0x0008 (VGA_EN is set)
(II) PCI-to-PCI bridge:
(II) Bus 1: bridge is at (0:8:0), (0,1,1), BCTRL: 0x0002 (VGA_EN is cleared)
(II) Bus 1 I/O range:
[0] -1 0 0x0000c000 - 0x0000cfff (0x1000) IX[B]
(II) Bus 1 non-prefetchable memory range:
[0] -1 0 0xec000000 - 0xecffffff (0x1000000) MX[B]
(II) PCI-to-PCI bridge:
(II) Bus 2: bridge is at (0:30:0), (0,2,2), BCTRL: 0x000a (VGA_EN is set)
(II) Bus 2 non-prefetchable memory range:
[0] -1 0 0xea000000 - 0xebffffff (0x2000000) MX[B]
(II) Bus 2 prefetchable memory range:
[0] -1 0 0xe0000000 - 0xe7ffffff (0x8000000) MX[B]
(--) PCI:*(2:0:0) nVidia Corporation NV18 [GeForce4 MX - nForce GPU] rev 163, Mem @ 0xea000000/24, 0xe0000000/26, 0xe4000000/19
(II) Addressable bus resource ranges are
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
[1] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) OS-reported resource ranges:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[6] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
(II) PCI Memory resource overlap reduced 0xe8000000 from 0xe9ffffff to 0xe7ffffff
(II) Active PCI resource ranges:
[0] -1 0 0xec000000 - 0xec000fff (0x1000) MX[B]
[1] -1 0 0xed001000 - 0xed001fff (0x1000) MX[B]
[2] -1 0 0xed000000 - 0xed000fff (0x1000) MX[B]
[3] -1 0 0xed005000 - 0xed0050ff (0x100) MX[B]
[4] -1 0 0xed004000 - 0xed004fff (0x1000) MX[B]
[5] -1 0 0xed003000 - 0xed003fff (0x1000) MX[B]
[6] -1 0 0xe8000000 - 0xe7ffffff (0x0) MX[B]O
[7] -1 0 0xe4000000 - 0xe407ffff (0x80000) MX[B](B)
[8] -1 0 0xe0000000 - 0xe3ffffff (0x4000000) MX[B](B)
[9] -1 0 0xea000000 - 0xeaffffff (0x1000000) MX[B](B)
[10] -1 0 0x0000c000 - 0x0000c0ff (0x100) IX[B]
[11] -1 0 0x0000f000 - 0x0000f00f (0x10) IX[B]
[12] -1 0 0x0000d800 - 0x0000d87f (0x80) IX[B]
[13] -1 0 0x0000d400 - 0x0000d4ff (0x100) IX[B]
[14] -1 0 0x0000d000 - 0x0000d007 (0x8) IX[B]
[15] -1 0 0x0000e400 - 0x0000e41f (0x20) IX[B]
(II) Active PCI resource ranges after removing overlaps:
[0] -1 0 0xec000000 - 0xec000fff (0x1000) MX[B]
[1] -1 0 0xed001000 - 0xed001fff (0x1000) MX[B]
[2] -1 0 0xed000000 - 0xed000fff (0x1000) MX[B]
[3] -1 0 0xed005000 - 0xed0050ff (0x100) MX[B]
[4] -1 0 0xed004000 - 0xed004fff (0x1000) MX[B]
[5] -1 0 0xed003000 - 0xed003fff (0x1000) MX[B]
[6] -1 0 0xe8000000 - 0xe7ffffff (0x0) MX[B]O
[7] -1 0 0xe4000000 - 0xe407ffff (0x80000) MX[B](B)
[8] -1 0 0xe0000000 - 0xe3ffffff (0x4000000) MX[B](B)
[9] -1 0 0xea000000 - 0xeaffffff (0x1000000) MX[B](B)
[10] -1 0 0x0000c000 - 0x0000c0ff (0x100) IX[B]
[11] -1 0 0x0000f000 - 0x0000f00f (0x10) IX[B]
[12] -1 0 0x0000d800 - 0x0000d87f (0x80) IX[B]
[13] -1 0 0x0000d400 - 0x0000d4ff (0x100) IX[B]
[14] -1 0 0x0000d000 - 0x0000d007 (0x8) IX[B]
[15] -1 0 0x0000e400 - 0x0000e41f (0x20) IX[B]
(II) OS-reported resource ranges after removing overlaps with PCI:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[6] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
(II) All system resource ranges:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0xec000000 - 0xec000fff (0x1000) MX[B]
[6] -1 0 0xed001000 - 0xed001fff (0x1000) MX[B]
[7] -1 0 0xed000000 - 0xed000fff (0x1000) MX[B]
[8] -1 0 0xed005000 - 0xed0050ff (0x100) MX[B]
[9] -1 0 0xed004000 - 0xed004fff (0x1000) MX[B]
[10] -1 0 0xed003000 - 0xed003fff (0x1000) MX[B]
[11] -1 0 0xe8000000 - 0xe7ffffff (0x0) MX[B]O
[12] -1 0 0xe4000000 - 0xe407ffff (0x80000) MX[B](B)
[13] -1 0 0xe0000000 - 0xe3ffffff (0x4000000) MX[B](B)
[14] -1 0 0xea000000 - 0xeaffffff (0x1000000) MX[B](B)
[15] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[16] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[17] -1 0 0x0000c000 - 0x0000c0ff (0x100) IX[B]
[18] -1 0 0x0000f000 - 0x0000f00f (0x10) IX[B]
[19] -1 0 0x0000d800 - 0x0000d87f (0x80) IX[B]
[20] -1 0 0x0000d400 - 0x0000d4ff (0x100) IX[B]
[21] -1 0 0x0000d000 - 0x0000d007 (0x8) IX[B]
[22] -1 0 0x0000e400 - 0x0000e41f (0x20) IX[B]
(II) LoadModule: "dbe"
(II) Loading /usr/lib/modules/extensions/libdbe.a
(II) Module dbe: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.2
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "glx"
(II) Loading /usr/lib/modules/extensions/libglx.a
(II) Module glx: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.2
(II) Loading sub module "GLcore"
(II) LoadModule: "GLcore"
(II) Loading /usr/lib/modules/extensions/libGLcore.a
(II) Module GLcore: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.2
(II) Loading extension GLX
(II) LoadModule: "extmod"
(II) Loading /usr/lib/modules/extensions/libextmod.a
(II) Module extmod: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.2
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "type1"
(II) Loading /usr/lib/modules/fonts/libtype1.a
(II) Module type1: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.2
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.4
(II) Loading font Type1
(II) Loading font CID
(II) LoadModule: "freetype"
(II) Loading /usr/lib/modules/fonts/libfreetype.so
(II) Module freetype: vendor="X.Org Foundation & the After X-TT Project"
compiled for 6.8.2, module version = 2.1.0
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.4
(II) Loading font FreeType
(II) LoadModule: "nvidia"
(WW) Warning, couldn't open module nvidia
(II) UnloadModule: "nvidia"
(EE) Failed to load module "nvidia" (module does not exist, 0)
(II) LoadModule: "mouse"
(II) Loading /usr/lib/modules/input/mouse_drv.o
(II) Module mouse: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.0
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 0.4
(II) LoadModule: "kbd"
(II) Loading /usr/lib/modules/input/kbd_drv.o
(II) Module kbd: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.0
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 0.4
(EE) No drivers available.
Fatal server error:
no screens found
Please consult the The X.Org Foundation support
at http://wiki.X.Org
for help.
Please also check the log file at "/var/log/Xorg.0.log" for additional information.
and xorg.conf
Code: Select all
amd X11 # cat xorg.conf
# **********************************************************************
# Files section. This allows default font and rgb paths to be set
# **********************************************************************
Section "Files"
RgbPath "/usr/lib/X11/rgb"
# For XFS, uncomment this and comment the others
# FontPath "unix/:-1"
FontPath "/usr/share/fonts/local/"
FontPath "/usr/share/fonts/misc/"
FontPath "/usr/share/fonts/75dpi/:unscaled"
FontPath "/usr/share/fonts/100dpi/:unscaled"
FontPath "/usr/share/fonts/Type1/"
FontPath "/usr/share/fonts/TTF/"
FontPath "/usr/share/fonts/CID/"
FontPath "/usr/share/fonts/Speedo/"
FontPath "/usr/share/fonts/75dpi/"
FontPath "/usr/share/fonts/100dpi/"
FontPath "/usr/share/fonts/arphicfonts/"
FontPath "/usr/share/fonts/cjkuni-fonts/"
FontPath "/usr/share/fonts/corefonts/"
FontPath "/usr/share/fonts/cronyx/"
FontPath "/usr/share/fonts/cyrillic/"
FontPath "/usr/share/fonts/default/"
FontPath "/usr/share/fonts/freefont/"
FontPath "/usr/share/fonts/hkscs-ming/"
FontPath "/usr/share/fonts/intlfonts/"
FontPath "/usr/share/fonts/terminus/"
FontPath "/usr/share/fonts/twmoefonts/"
FontPath "/usr/share/fonts/ukr/"
FontPath "/usr/share/fonts/util/"
FontPath "/usr/share/fonts/zh-kcfonts/"
EndSection
# **********************************************************************
# Module section -- this is an optional section which is used to specify
# which run-time loadable modules to load when the X server starts up.
# **********************************************************************
Section "Module"
# This loads the DBE extension module.
Load "dbe"
Load "glx"
Load "extmod"
# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
# SubSection "extmod"
# Option "omit xfree86-dga"
# EndSubSection
# This loads the Type1 and FreeType font modules
Load "type1"
Load "freetype"
EndSection
# **********************************************************************
# Server flags section. This contains various server-wide Options.
# **********************************************************************
Section "ServerFlags"
# Uncomment this to cause a core dump at the spot where a signal is
# received. This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging
# Option "NoTrapSignals"
# Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence
# (where n is 1 through 12). This allows clients to receive these key
# events.
# Option "DontVTSwitch"
# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
# This allows clients to receive this key event.
# Option "DontZap"
# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
# sequences. This allows clients to receive these key events.
# Option "DontZoom"
# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.
# Option "DisableVidModeExtension"
# Uncomment this to enable the use of a non-local xvidtune client.
# Option "AllowNonLocalXvidtune"
# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings.
# Option "DisableModInDev"
# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).
# Option "AllowNonLocalModInDev"
# Set the basic blanking screen saver timeout.
Option "blank time" "10" # 10 minutes
# Set the DPMS timeouts. These are set here because they are global
# rather than screen-specific. These settings alone don't enable DPMS.
# It is enabled per-screen (or per-monitor), and even then only when
# the driver supports it.
Option "standby time" "20"
Option "suspend time" "30"
Option "off time" "60"
# On some platform the server needs to estimate the sizes of PCI
# memory and pio ranges. This is done by assuming that PCI ranges
# don't overlap. Some broken BIOSes tend to set ranges of inactive
# devices wrong. Here one can adjust how aggressive the assumptions
# should be. Default is 0.
# Option "EstimateSizesAggresively" "0"
EndSection
# **********************************************************************
# Input devices
# **********************************************************************
# **********************************************************************
# Core keyboard's InputDevice section
# **********************************************************************
Section "InputDevice"
Identifier "Keyboard1"
Driver "kbd"
# Option "Protocol" "Xqueue"
Option "AutoRepeat" "500 30"
# Specifiy which keyboard LEDs can be user-controlled (eg, with xset(1)).
# Option "Xleds" "1 2 3"
# To disable the XKEYBOARD extension, uncomment XkbDisable.
# Option "XkbDisable"
# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults). For example, for a European
# keyboard, you will probably want to use one of:
#
# Option "XkbModel" "pc102"
# Option "XkbModel" "pc105"
#
# If you have a Microsoft Natural keyboard, you can use:
#
# Option "XkbModel" "microsoft"
#
# If you have a US "windows" keyboard you will want:
#
Option "XkbModel" "pc104"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
#
# Option "XkbLayout" "de"
#
# or:
#
# Option "XkbLayout" "de"
# Option "XkbVariant" "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
#
# Option "XkbOptions" "ctrl:swapcaps"
# These are the default XKB settings for xorg
#
# Option "XkbModel" "pc101"
Option "XkbLayout" "us"
# Option "XkbVariant" ""
# Option "XkbOptions" ""
EndSection
# **********************************************************************
# Core Pointer's InputDevice section
# **********************************************************************
Section "InputDevice"
# Identifier and driver
Identifier "Mouse1"
Driver "mouse"
# The mouse protocol and device. The device is normally set to /dev/mouse,
# which is usually a symbolic link to the real device.
Option "Protocol" "IMPS/2"
# Option "Protocol" "Microsoft"
# Option "Device" "/dev/mouse"
Option "Device" "/dev/input/mice"
# On platforms where PnP mouse detection is supported the following
# protocol setting can be used when using a newer PnP mouse:
# Option "Protocol" "Auto"
# When using mouse connected to a PS/2 port (aka "MousePort"), set the
# the protocol as follows. On some platforms some other settings may
# be available.
# Option "Protocol" "PS/2"
# When using XQUEUE (only for SVR3 and SVR4, but not Solaris), use
# the following instead of any of the lines above. The Device line
# is not required in this case.
# Option "Protocol" "Xqueue"
# Baudrate and SampleRate are only for some older Logitech mice. In
# almost every case these lines should be omitted.
# Option "BaudRate" "9600"
# Option "SampleRate" "150"
# Emulate3Buttons is an option for 2-button mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)
Option "Emulate3Buttons"
Option "ZAxisMapping" "4 5"
# Option "Emulate3Timeout" "50"
# ChordMiddle is an option for some 3-button Logitech mice, or any
# 3-button mouse where the middle button generates left+right button
# events.
# Option "ChordMiddle"
EndSection
# **********************************************************************
# Monitor section
# **********************************************************************
# Any number of monitor sections may be present
Section "Monitor"
# The identifier line must be present.
Identifier "ViewSonic VA720"
HorizSync 30-82
VertRefresh 50-75
# A generic VGA 640x480 mode (hsync = 31.5kHz, refresh = 60Hz)
# These two are equivalent
# ModeLine "640x480" 25.175 640 664 760 800 480 491 493 525
# Mode "1024x768"
# DotClock 25.175
# EndMode
# Mode "640x480"
# DotClock 25.175
# HTimings 640 664 760 800
# VTimings 480 491 493 525
# EndMode
# These two are equivalent
# ModeLine "1024x768i" 45 1024 1048 1208 1264 768 776 784 817 Interlace
# Mode "1024x768i"
# DotClock 45
# HTimings 1024 1048 1208 1264
# VTimings 768 776 784 817
# Flags "Interlace"
# EndMode
# If a monitor has DPMS support, that can be indicated here. This will
# enable DPMS when the monitor is used with drivers that support it.
Option "dpms"
# If a monitor requires that the sync signals be superimposed on the
# green signal, the following option will enable this when used with
# drivers that support it. Only a relatively small range of hardware
# (and drivers) actually support this.
# Option "sync on green"
EndSection
# **********************************************************************
# Graphics device section
# **********************************************************************
# Any number of graphics device sections may be present
Section "Device"
Identifier "nVidia GeForce"
Driver "nvidia"
VideoRam 65536
BusID "PCI:2:0:0"
Screen 0
EndSection
# **********************************************************************
# Screen sections.
# **********************************************************************
# Any number of screen sections may be present. Each describes
# the configuration of a single screen. A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
# The Identifier, Device and Monitor lines must be present
Identifier "Screen0"
# Device "Generic VGA"
Device "nVidia GeForce"
Monitor "ViewSonic VA720"
# The favoured Depth and/or Bpp may be specified here
DefaultDepth 24
SubSection "Display"
Depth 24
Modes "1280x1024"
ViewPort 0 0
# Virtual 1024 768
EndSubsection
# SubSection "Display"
# Depth 8
# Modes "640x480"
# ViewPort 0 0
# Virtual 800 600
# EndSubsection
# SubSection "Display"
# Depth 4
# Modes "640x480"
# EndSubSection
# SubSection "Display"
# Depth 1
# Modes "640x480"
# EndSubSection
EndSection
Section "ServerLayout"
# The Identifier line must be present
Identifier "Main Layout"
Screen 0 "Screen0"
InputDevice "Mouse1" "CorePointer"
# InputDevice "Mouse2" "SendCoreEvents"
InputDevice "Keyboard1" "CoreKeyboard"
EndSection
amd X11 #
ditto
almost the exact same issue here - I get the messege "Failed to initialize the nvidia kernel module" even though the nvidia module was loaded earlier with no warnings that I could see in dmesg. Not sure whether to downgrade.....urgh.
I don't know whether this is just a recent thing as I don't use it myself, but I'm pretty sure the framebuffer (from dmesg it looks like you're using that) is incompatible with the nvidia kernel module. I don't know if it works with the kernel's agp module instead.
Try rebuilding your kernel without framebuffer support and see how it goes.
Try rebuilding your kernel without framebuffer support and see how it goes.
Jingle Jangle Jewellery
- PsychoticRetina
- Guru
- Posts: 352
- Joined: Sun Dec 18, 2005 10:59 pm
- Location: behind the scalpel
concur. 2.6.14-r5 and 1.0.8178 nvidia on my box. as soon as i got rid of framebuffer support, X started without problems.agent_jdh wrote:I don't know whether this is just a recent thing as I don't use it myself, but I'm pretty sure the framebuffer (from dmesg it looks like you're using that) is incompatible with the nvidia kernel module. I don't know if it works with the kernel's agp module instead.
Try rebuilding your kernel without framebuffer support and see how it goes.
Quite strange. Its working fine for me gentoo-2.6.14-r5 kernel, 8178 drivers, fancy framebuffer, Xorg 7.0 (worked on 6.8.99 too).
Have you tried the run package from the nvidia site aswell as the ebuild (both work for me). Framebuffer wise, as long as your using the vesa buffer and NOT the nvidia one, it shouldn't conflict.
Have you tried the run package from the nvidia site aswell as the ebuild (both work for me). Framebuffer wise, as long as your using the vesa buffer and NOT the nvidia one, it shouldn't conflict.
Maybe the combination of the vesa framebuffer and/or xorg 7/6.8.99 is the key here.riven wrote:Quite strange. Its working fine for me gentoo-2.6.14-r5 kernel, 8178 drivers, fancy framebuffer, Xorg 7.0 (worked on 6.8.99 too).
Have you tried the run package from the nvidia site aswell as the ebuild (both work for me). Framebuffer wise, as long as your using the vesa buffer and NOT the nvidia one, it shouldn't conflict.
I'd avoid running the nvidia driver binary installer though - it can be a nightmare to clean up from. Trust me, I've been there when it starts causing trouble. Stick to the ebuilds.
Jingle Jangle Jewellery