im trying to install gentoo on HP Compaq ML150. It has 2 sata hard drives in raid1. Raid controller is Marvell MV88SX6041 4-port SATA II PCI-X Controller. Problem is, it doesnt make me device( /dev/* ) and i cannot acces disks for installation.. bad sutff
lspci:
0000:00:00.0 Host bridge: Intel Corporation E7320 Memory Controller Hub (rev 0c)
0000:00:02.0 PCI bridge: Intel Corporation E7525/E7520/E7320 PCI Express Port A (rev 0c)
0000:00:03.0 PCI bridge: Intel Corporation E7525/E7520/E7320 PCI Express Port A1 (rev 0c)
0000:00:1c.0 PCI bridge: Intel Corporation 6300ESB 64-bit PCI-X Bridge (rev 02)
0000:00:1d.0 USB Controller: Intel Corporation 6300ESB USB Universal Host Controller (rev 02)
0000:00:1d.1 USB Controller: Intel Corporation 6300ESB USB Universal Host Controller (rev 02)
0000:00:1d.4 System peripheral: Intel Corporation 6300ESB Watchdog Timer (rev 02)
0000:00:1d.5 PIC: Intel Corporation 6300ESB I/O Advanced Programmable Interrupt Controller (rev 02)
0000:00:1d.7 USB Controller: Intel Corporation 6300ESB USB2 Enhanced Host Controller (rev 02)
0000:00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 0a)
0000:00:1f.0 ISA bridge: Intel Corporation 6300ESB LPC Interface Controller (rev 02)
0000:00:1f.1 IDE interface: Intel Corporation 6300ESB PATA Storage Controller (rev 02)
0000:00:1f.3 SMBus: Intel Corporation 6300ESB SMBus Controller (rev 02)
0000:02:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express (rev 11)
0000:03:04.0 SCSI storage controller: Marvell Technology Group Ltd. MV88SX6041 4-port SATA II PCI-X Controller (rev 07)
0000:04:04.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27)
dmesg:
Linux version 2.6.11-gentoo-r3 (root@nemo) (gcc version 3.3.5 (Gentoo Linux 3.3.5-r1, ssp-3.3.2-3, pie-8.7.7.1)) #1 SMP Fri Mar 18 21:30:04 UTC 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 0000000000097800 (usable)
BIOS-e820: 0000000000097800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000ce000 - 00000000000d0000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007ff70000 (usable)
BIOS-e820: 000000007ff70000 - 000000007ff7b000 (ACPI data)
BIOS-e820: 000000007ff7b000 - 000000007ff80000 (ACPI NVS)
BIOS-e820: 000000007ff80000 - 0000000080000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fffffc00 - 0000000100000000 (reserved)
1151MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f6a90
On node 0 totalpages: 524144
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 225280 pages, LIFO batch:16
HighMem zone: 294768 pages, LIFO batch:16
DMI present.
ACPI: RSDP (v000 PTLTD ) @ 0x000f6a10
ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x7ff77716
ACPI: FADT (v001 HP TUMWATER 0x06040000 PTL 0x00000003) @ 0x7ff7af18
ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0x7ff7af8c
ACPI: DSDT (v001 HP TUMWATER 0x06040000 MSFT 0x0100000e) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:4 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 15:4 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x03] address[0xfec10000] gsi_base[24])
IOAPIC[1]: apic_id 3, version 32, address 0xfec10000, GSI 24-47
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 2 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 80000000 (gap: 80000000:60000000)
Built 1 zonelists
Kernel command line: initrd=gentoo.igz root=/dev/ram0 init=/linuxrc looptype=squashfs loop=/livecd.squashfs udev nodevfs cdroot vga=791 dokeymap splash=silent,theme:livecd-2005.0 BOOT_IMAGE=gentoo
fbsplash: silent
fbsplash: theme livecd-2005.0
__iounmap: bad address c00fffd9
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
mapped IOAPIC to ffffb000 (fec10000)
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 2993.863 MHz processor.
Using tsc for high-res timesource
Speakup v-2.00 CVS: Wed Mar 2 20:22:02 EST 2005 : initialized
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 2071464k/2096576k available (2240k kernel code, 24244k reserved, 587k data, 1228k init, 1179072k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 5914.62 BogoMIPS (lpj=2957312)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Couldn't initialize miscdevice /dev/synth.
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000641d 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000 0000641d 00000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 20100000 00000000 00000080 0000641d 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: Intel(R) Xeon(TM) CPU 3.00GHz stepping 01
per-CPU timeslice cutoff: 2925.86 usecs.
task migration cache decay timeout: 3 msecs.
Booting processor 1/1 eip 2000
Initializing CPU#1
Calibrating delay loop... 5980.16 BogoMIPS (lpj=2990080)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000641d 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000 0000641d 00000000 00000000
monitor/mwait feature present.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 20100000 00000000 00000080 0000641d 00000000 00000000
CPU1: Intel(R) Xeon(TM) CPU 3.00GHz stepping 01
Total of 2 processors activated (11894.78 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
CPU0 attaching sched-domain:
domain 0: span 03
groups: 01 02
domain 1: span 03
groups: 03
CPU1 attaching sched-domain:
domain 0: span 03
groups: 02 01
domain 1: span 03
groups: 03
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 2414k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfde4f, last bus=4
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIX._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 4 5 6 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 4 5 6 7 10 *11 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 11 devices
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to bjorn.helgaas@hp.com
** so I can fix the driver.
highmem bounce pool size: 64 pages
inotify device minor=63
Squashfs 2.1 (released 2004/12/10) (C) 2002-2004 Phillip Lougher
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:02.0 to 64
Allocate Port Service[pcie00]
ACPI: PCI interrupt 0000:00:03.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:03.0 to 64
Allocate Port Service[pcie00]
vesafb: framebuffer at 0xde000000, mapped to 0xf8880000, using 3072k, total 8128k
vesafb: mode is 1024x768x16, linelength=2048, pages=4
vesafb: protected mode interface info at c000:4a64
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fbsplash: console 0 using theme 'livecd-2005.0'
fbsplash: switched splash state to 'on' on console 0
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
io scheduler noop registered
io scheduler deadline registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH5: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1440-0x1447, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1448-0x144f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: SAMSUNG CD-ROM SC-148A, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
fbsplash: switching to verbose mode
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: ATAPI 48X CD-ROM drive, 128kB Cache, UDMA(25)
Uniform CD-ROM driver Revision: 3.20
CAPI Subsystem Rev 1.1.2.8
EISA: Probing bus 0 at eisa0
Cannot allocate resource for EISA slot 1
Cannot allocate resource for EISA slot 2
Cannot allocate resource for EISA slot 3
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 16384 buckets, 128Kbytes
TCP established hash table entries: 524288 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 524288 bind 65536)
NET: Registered protocol family 1
NET: Registered protocol family 17
Starting balanced_irq
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 1228k freed
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 23, pci mem 0xdd001400
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.0: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 16, io base 0x1400
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.1 -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 19, io base 0x1420
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
sl811: driver sl811-hcd, 15 Dec 2004
ieee1394: Initialized config rom entry `ip1394'
sbp2: $Rev: 1219 $ Ben Collins <bcollins@debian.org>
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
dm_snapshot: Unknown symbol dm_table_get_size
libata version 1.10 loaded.
ReiserFS: hda: warning: sh-2021: reiserfs_fill_super: can not find reiserfs on hda
VFS: Can't find ext3 filesystem on dev hda.
VFS: Can't find an ext2 filesystem on dev hda.
SQUASHFS error: Can't find a SQUASHFS superblock on hda
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev hda.
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
tg3.c:v3.23 (February 15, 2005)
ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:02:00.0 to 64
eth0: Tigon3 [partno(BCM95721) rev 4101 PHY(5750)] (PCIX:100MHz:32-bit) 10/100/1000BaseT Ethernet 00:13:21:b4:a6:39
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
Real Time Clock Driver v1.12
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
fbsplash: console 11 using theme 'livecd-2005.0'
fbsplash: switched splash state to 'on' on console 11
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
greets
marduk21
