DVD+R burning problems

Message

bdonlan · Post by **bdonlan** » Sun Oct 10, 2004 7:44 pm

I've been trying to burn a DVD+R with dvdrtools-0.1.6, but it fails with:

dvdrecord -fs=10m speed=16 dev=0,0,0 -vvvv -dao ^M -dummy driveropts=burnfree -data image.iso 
dvdrtools v0.1.6
Portions (c) 2002-2003 Ark Linux <bero@arklinux.org>
This program is free software; you can redistribute it and/or modify it under
the terms of the GNU General Public License as published by the Free Software
Foundation; either version 2, or (at your option) any later version.

This program is distributed in the hope that it will be useful, but WITHOUT ANY
WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR
A PARTICULAR PURPOSE.  See the GNU General Public License for more details.

You should have received a copy of the GNU General Public License along with
this program; see the file COPYING.  If not, write to the Free Software
Foundation, 59 Temple Place, Suite 330, Boston, MA 02111-1307, USA.
Based on:
Cdrecord 1.11a15 (i686-pc-linux-gnu) Copyright (C) 1995-2001 J�rg Schilling
TOC Type: 1 = CD-ROM
scsidev: '0,0,0'
scsibus: 0 target: 0 lun: 0
Linux sg driver version: 3.5.31
Using libscg version 'bero-0.5a'
dvdrecord: Warning: using inofficial version of libscg (bero-0.5a '@(#)scsitransp.c     1.81 01/04/20 Copyright 1988,1995,2000
 J. Schilling').
Using libscg transport code version 'schily-scsi-linux-sg.c-1.69'
Driveropts: 'burnfree'
atapi: 1
Device type    : Removable CD-ROM
Version        : 2
Response Format: 2
Capabilities   : 
Vendor_info    : 'HP      '
Identifikation : 'DVD Writer 300n '
Revision       : '3.11'
Device seems to be: Generic mmc2 DVD-ROM.
Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
Driver flags   : SWABAUDIO BURNFREE 
Supported modes: TAO PACKET SAO SAO/R96R RAW/R96R
Drive buf size : 1605632 = 1568 KB
FIFO size      : 10485760 = 10240 KB
Track 01: data  4375 MB        
track: 1 start: 0 pregap: 150
Total size:     5025 MB (497:50.50) = 2240288 sectors
Lout start:     5025 MB (497:52/38) = 2240288 sectors
 41 00 00 14 00 00 00 00
 41 01 00 10 00 00 00 00
 41 01 01 10 00 00 02 00
 41 AA 01 14 00 F1 34 26
Track 1 start 0
Track 2 start 2240288
 41 00 A0 00 00 00 00 01 00 00 00 00
 41 00 A1 00 00 00 00 01 00 00 00 00
 41 00 A2 00 00 00 00 FB 52 38 00 00
 41 00 01 00 00 00 00 00 02 00 00 00
Current Secsize: 2048
  ATIP start of lead in:  -150 (00:00/00)
  ATIP start of lead out: 157789 (35:05/64)
Disk type:    unknown dye (reserved id code)
Manuf. index: -1
Manufacturer: unknown (not in table)
Blocks total: 157789 Blocks current: 157789 Blocks remaining: -2082499
dvdrecord: WARNING: Data may not fit on current disk.
dvdrecord: Notice: Most recorders cannot write CD's >= 90 minutes.
dvdrecord: Notice: Use -ignsize option to allow >= 90 minutes.
dvdrecord: Notice: Use -overburn option to write more than the official disk capacity.
dvdrecord: Notice: Most CD-writers do overburning only on DAO mode.

When I specify -ignsize and -overburn, it fails with:

Code: Select all

dvdrtools v0.1.6
Portions (c) 2002-2003 Ark Linux <bero@arklinux.org>
This program is free software; you can redistribute it and/or modify it under
the terms of the GNU General Public License as published by the Free Software
Foundation; either version 2, or (at your option) any later version.

This program is distributed in the hope that it will be useful, but WITHOUT ANY
WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR
A PARTICULAR PURPOSE.  See the GNU General Public License for more details.

You should have received a copy of the GNU General Public License along with
this program; see the file COPYING.  If not, write to the Free Software
Foundation, 59 Temple Place, Suite 330, Boston, MA 02111-1307, USA.
Based on:
Cdrecord 1.11a15 (i686-pc-linux-gnu) Copyright (C) 1995-2001 J�rg Schilling
TOC Type: 1 = CD-ROM
scsidev: '0,0,0'
scsibus: 0 target: 0 lun: 0
Linux sg driver version: 3.5.31
Using libscg version 'bero-0.5a'
dvdrecord: Warning: using inofficial version of libscg (bero-0.5a '@(#)scsitransp.c     1.81 01/04/20 Copyright 1988,1995,2000
 J. Schilling').
Using libscg transport code version 'schily-scsi-linux-sg.c-1.69'
Driveropts: 'burnfree'
atapi: 1
Device type    : Removable CD-ROM
Version        : 2
Response Format: 2
Capabilities   : 
Vendor_info    : 'HP      '
Identifikation : 'DVD Writer 300n '
Revision       : '3.11'
Device seems to be: Generic mmc2 DVD-ROM.
Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
Driver flags   : SWABAUDIO BURNFREE 
Supported modes: TAO PACKET SAO SAO/R96R RAW/R96R
Drive buf size : 1605632 = 1568 KB
FIFO size      : 10485760 = 10240 KB
Track 01: data  4375 MB        
track: 1 start: 0 pregap: 150
Total size:     5025 MB (497:50.50) = 2240288 sectors
Lout start:     5025 MB (497:52/38) = 2240288 sectors
 41 00 00 14 00 00 00 00
 41 01 00 10 00 00 00 00
 41 01 01 10 00 00 02 00
 41 AA 01 14 00 F1 34 26
Track 1 start 0
Track 2 start 2240288
 41 00 A0 00 00 00 00 01 00 00 00 00
 41 00 A1 00 00 00 00 01 00 00 00 00
 41 00 A2 00 00 00 00 FB 52 38 00 00
 41 00 01 00 00 00 00 00 02 00 00 00
Current Secsize: 2048
  ATIP start of lead in:  -150 (00:00/00)
  ATIP start of lead out: 157789 (35:05/64)
Disk type:    unknown dye (reserved id code)
Manuf. index: -1
Manufacturer: unknown (not in table)
Blocks total: 157789 Blocks current: 157789 Blocks remaining: -2082499
dvdrecord: WARNING: Data may not fit on current disk.
dvdrecord: Notice: Overburning active. Trying to write more than the official disk capacity.
Starting to write CD/DVD at speed 16 in dummy mode for single session.
Last chance to quit, starting dummy write in 0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
BURN-Free is ON.
dvdrecord: Turning BURN-Free on
Sending CUE sheet...
 41 00 00 14 00 00 00 00
 41 01 00 10 00 00 00 00
 41 01 01 10 00 00 02 00
 41 AA 01 14 00 F1 34 26
dvdrecord: CUE sheet not accepted. Retrying with minimum pregapsize = 1.
 41 00 00 14 00 00 00 00
 41 01 00 10 00 00 00 00
 41 01 01 10 00 00 02 00
 41 AA 01 14 00 F1 34 26
dvdrecord: Input/output error. send_cue_sheet: scsi sendcmd: no error
CDB:  5D 00 00 00 00 00 00 00 20 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0A 00 00 00 00 26 00 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x26 Qual 0x00 (invalid field in parameter list) Fru 0x0
Sense flags: Blk 0 (not valid) 
cmd finished after 0.002s timeout 200s
dvdrecord: Cannot send CUE sheet.
dvdrecord: fifo had 160 puts and 0 gets.
dvdrecord: fifo was 0 times empty and 0 times full, min fill was 100%.

I'm using Memorex 4x DVD+Rs, and kernel 2.6.8-gentoo-r3 with ide-scsi. How can I get it to record correctly? Also, how can I get DVD burning with ATAPI to work?

snowbum · Post by **snowbum** » Sun Oct 10, 2004 9:32 pm

I'm not at all sure what your problem is as far as the SCSI is concerned. But to get your ATAPI writer working, AFAIK, you need to config this in the kernel. You should also not use SCSI emulation. I've never been able to get an ATAPI DVD writer to work with SCSI emulation. I'd say ATAPI is you best shot.

If you have no SCSI devices, you can completly turn of SCSI support. I think USB devices and the like will still show up as SCSI devices fine.

Someone correct me if I'm wrong.

bdonlan · Post by **bdonlan** » Sun Oct 10, 2004 9:51 pm

snowbum wrote:I'm not at all sure what your problem is as far as the SCSI is concerned. But to get your ATAPI writer working, AFAIK, you need to config this in the kernel. You should also not use SCSI emulation. I've never been able to get an ATAPI DVD writer to work with SCSI emulation. I'd say ATAPI is you best shot.

If you have no SCSI devices, you can completly turn of SCSI support. I think USB devices and the like will still show up as SCSI devices fine.

Someone correct me if I'm wrong.

dvdrtools does not support ATAPI burning.

snowbum · Post by **snowbum** » Sun Oct 10, 2004 10:06 pm

I must have used cdrecord... Yes, that is what I used.

Gavrila · Post by **Gavrila** » Sun Oct 10, 2004 10:29 pm

dunno what k3b uses (but I guess dvdrecord), yet I burnt a dvd+rw with k3b and I don't use SCSI emulation at all

snowbum · Post by **snowbum** » Sun Oct 10, 2004 11:37 pm

I'm pretty sure K3b uses cdrecord. Though I could be wrong. Well, to be fair, my K3b uses it.

bdonlan · Post by **bdonlan** » Mon Oct 11, 2004 12:05 am

nm, cdrecord-ProDVD fixed it.

Gavrila · Post by **Gavrila** » Mon Oct 11, 2004 7:43 am

snowbum wrote:I'm pretty sure K3b uses cdrecord. Though I could be wrong. Well, to be fair, my K3b uses it.

not to be silly but I guess that cdrecord is a symlink to dvdrecord... so we're starting over agian: Though it has been stated that it doesnt work with ATAPI, I succeded at it.