| View previous topic :: View next topic |
| Author |
Message |
JumboAg
Apprentice
Joined: 03 Mar 2007
Posts: 220
Location: Dallas, TX
|
 Posted: Sat Apr 19, 2025 2:35 am Post subject: [SOLVED] Cannnot boot new amlogic SBC |
 |
|
Trying to setup yet another SBC and have run into a couple of problems.
#1 - No framebuffer. I'll figure this one out later. For now I'm using a UART for testing anyway.
#2 - Wont finish booting. (See output below)
The sd card is not encrypted so not sure why it would be hanging on that service..
| Code: | U-Boot 2023.07+ (Sep 20 2023 - 03:58:15 -0400) Libre Computer AML-S905D3-CC
Model: Libre Computer AML-S905D3-CC
SoC: Amlogic Meson SM1 (S905D3) Revision 2b:c (4:2)
DRAM: 2 GiB (effective 3.8 GiB)
Core: 403 devices, 30 uclasses, devicetree: separate
WDT: Not starting watchdog@f0d0
MMC: mmc@ffe05000: 1, mmc@ffe07000: 0
Loading Environment from FAT... Card did not respond to voltage select! : -110
** Bad device specification mmc 0 **
Card did not respond to voltage select! : -110
** Bad device specification mmc 0 **
Couldn't find partition mmc 0
Card did not respond to voltage select! : -110
** Bad device specification mmc 0 **
Couldn't find partition mmc 0
Error: could not access storage.
starting USB...
Bus usb@ff500000: Register 3000140 NbrPorts 3
Starting the controller
USB XHCI 1.10
scanning bus usb@ff500000 for devices... Device NOT ready
Request Sense returned 02 3A 00
Device NOT ready
Request Sense returned 02 3A 00
5 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
Scanning for bootflows in all bootdevs
Seq Method State Uclass Part Name Filename
--- ----------- ------ -------- ---- ------------------------ ----------------
Scanning global bootmeth 'efi_mgr':
Scanning bootdev 'mmc@ffe07000.bootdev':
Card did not respond to voltage select! : -110
Scanning bootdev 'mmc@ffe05000.bootdev':
0 efi ready mmc 1 mmc@ffe05000.bootdev.part efi/boot/bootaa64.efi
** Booting bootflow 'mmc@ffe05000.bootdev.part_1' with efi
Card did not respond to voltage select! : -110
Booting /efi\boot\bootaa64.efi
EFI stub: Decompressing Linux Kernel...
EFI stub: Loaded initrd from LINUX_EFI_INITRD_MEDIA_GUID device path
EFI stub: Using DTB from configuration table
EFI stub: Exiting boot services...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x411fd050]
[ 0.000000] Linux version 6.12.21-gentoo-dist (root@dola.arm.dev.gentoo.org) (aarch64-unknown-linux-gnu-gcc (Gentoo 14.2.1_p20241221 p7) 14.2.1 20241221, GNU ld (Gentoo 2.44 p1) 2.44.0) #1 SMP PREEMPT_DYNAMIC Sat Mar 29 11:37:58 -00 2025
[ 0.000000] KASLR enabled
[ 0.000000] Machine model: Libre Computer AML-S905D3-CC
[ 0.000000] efi: EFI v2.10 by Das U-Boot
[ 0.000000] efi: RTPROP=0xe9e7f040 SMBIOS=0xe9e7e000 INITRD=0xe6bb4040 RNG=0xe56f8040 MEMRESERVE=0xe56f7040
[ 0.000000] random: crng init done
[ 0.000000] Reserved memory: created CMA memory pool at 0x00000000cf800000, size 256 MiB
[ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[ 0.000000] OF: reserved mem: 0x00000000cf800000..0x00000000df7fffff (262144 KiB) map reusable linux,cma
[ 0.000000] OF: reserved mem: 0x0000000005000000..0x00000000052fffff (3072 KiB) nomap non-reusable secmon@5000000
[ 0.000000] OF: reserved mem: 0x0000000005300000..0x00000000072fffff (32768 KiB) nomap non-reusable secmon@5300000
[ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x00000000f4ffffff]
[ 0.000000] NODE_DATA(0) allocated [mem 0xf3d1b200-0xf3d31f3f]
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000000000-0x00000000f4ffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Device empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000004ffffff]
[ 0.000000] node 0: [mem 0x0000000005000000-0x00000000072fffff]
[ 0.000000] node 0: [mem 0x0000000007300000-0x00000000e9e7dfff]
[ 0.000000] node 0: [mem 0x00000000e9e7e000-0x00000000e9e7ffff]
[ 0.000000] node 0: [mem 0x00000000e9e80000-0x00000000e9e80fff]
[ 0.000000] node 0: [mem 0x00000000e9e81000-0x00000000e9e86fff]
[ 0.000000] node 0: [mem 0x00000000e9e87000-0x00000000f2e9ffff]
[ 0.000000] node 0: [mem 0x00000000f2ea0000-0x00000000f2eaffff]
[ 0.000000] node 0: [mem 0x00000000f2eb0000-0x00000000f4725fff]
[ 0.000000] node 0: [mem 0x00000000f4726000-0x00000000f4ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00000000f4ffffff]
[ 0.000000] On node 0, zone DMA: 12288 pages in unavailable ranges
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.1
[ 0.000000] percpu: Embedded 56 pages/cpu s104600 r8192 d116584 u229376
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: Virtualization Host Extensions
[ 0.000000] CPU features: kernel page table isolation forced ON by KASLR
[ 0.000000] CPU features: detected: Kernel page table isolation (KPTI)
[ 0.000000] CPU features: detected: Qualcomm erratum 1009, or ARM erratum 1286807, 2441009
[ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[ 0.000000] alternatives: applying boot alternatives
[ 0.000000] Kernel command line: BOOT_IMAGE=/kernel-6.12.21-gentoo-dist root=UUID=a39c0ab6-c7fb-4958-b691-178604eaa03d ro nomodeset
[ 0.000000] Booted with the nomodeset parameter. Only the system framebuffer will be available
[ 0.000000] Unknown kernel command line parameters "BOOT_IMAGE=/kernel-6.12.21-gentoo-dist", will be passed to user space.
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[ 0.000000] Fallback order for Node 0: 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1003520
[ 0.000000] Policy zone: DMA
[ 0.000000] mem auto-init: stack:all(zero), heap alloc:on, heap free:off
[ 0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 3MB
[ 0.000000] software IO TLB: area num 4.
[ 0.000000] software IO TLB: mapped [mem 0x00000000f31ca000-0x00000000f35ca000] (4MB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] ftrace: allocating 68944 entries in 270 pages
[ 0.000000] ftrace: allocated 270 pages with 4 groups
[ 0.000000] Dynamic Preempt: voluntary
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=4.
[ 0.000000] Trampoline variant of Tasks RCU enabled.
[ 0.000000] Rude variant of Tasks RCU enabled.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] RCU Tasks: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
[ 0.000000] RCU Tasks Rude: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
[ 0.000000] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] Root IRQ handler: gic_handle_irq
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.000506] kfence: initialized - using 2097152 bytes for 255 objects at 0x(____ptrval____)-0x(____ptrval____)
[ 0.000730] Console: colour dummy device 80x25
[ 0.000745] printk: legacy console [tty0] enabled
[ 0.001557] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[ 0.001589] pid_max: default: 32768 minimum: 301
[ 0.001796] LSM: initializing lsm=lockdown,capability,yama,ima,evm
[ 0.001906] Yama: becoming mindful.
[ 0.002155] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.002191] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.003796] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.017150] rcu: Hierarchical SRCU implementation.
[ 0.017193] rcu: Max phase no-delay instances is 1000.
[ 0.017508] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level
[ 0.022895] Remapping and enabling EFI services.
[ 0.023498] smp: Bringing up secondary CPUs ...
[ 0.034010] Detected VIPT I-cache on CPU1
[ 0.034099] CPU1: Booted secondary processor 0x0000000100 [0x411fd050]
[ 0.050606] Detected VIPT I-cache on CPU2
[ 0.050688] CPU2: Booted secondary processor 0x0000000200 [0x411fd050]
[ 0.064000] Detected VIPT I-cache on CPU3
[ 0.064080] CPU3: Booted secondary processor 0x0000000300 [0x411fd050]
[ 0.064283] smp: Brought up 1 node, 4 CPUs
[ 0.064362] SMP: Total of 4 processors activated.
[ 0.064375] CPU: All CPU(s) started at EL2
[ 0.064389] CPU features: detected: 32-bit EL0 Support
[ 0.064402] CPU features: detected: 32-bit EL1 Support
[ 0.064417] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[ 0.064435] CPU features: detected: Common not Private translations
[ 0.064449] CPU features: detected: CRC32 instructions
[ 0.064462] CPU features: detected: Data cache clean to Point of Persistence
[ 0.064483] CPU features: detected: RCpc load-acquire (LDAPR)
[ 0.064497] CPU features: detected: LSE atomic instructions
[ 0.064511] CPU features: detected: Privileged Access Never
[ 0.064524] CPU features: detected: RAS Extension Support
[ 0.064596] alternatives: applying system-wide alternatives
[ 0.069489] Memory: 3539672K/4014080K available (22208K kernel code, 5532K rwdata, 18040K rodata, 13440K init, 1485K bss, 205028K reserved, 262144K cma-reserved)
[ 0.070970] devtmpfs: initialized
[ 0.085132] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[ 0.085202] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.092140] 2G module region forced by RANDOMIZE_MODULE_REGION_FULL
[ 0.092193] 0 pages in range for non-PLT usage
[ 0.092199] 509056 pages in range for PLT usage
[ 0.092572] pinctrl core: initialized pinctrl subsystem
[ 0.095421] SMBIOS 3.0 present.
[ 0.095463] DMI: libre-computer aml-s905d3-cc/aml-s905d3-cc, BIOS 2023.07+ 07/01/2023
[ 0.095493] DMI: Memory slots populated: 0/0
[ 0.098567] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.100403] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations
[ 0.101114] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.102412] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.102542] audit: initializing netlink subsys (disabled)
[ 0.102885] audit: type=2000 audit(0.099:1): state=initialized audit_enabled=0 res=1
[ 0.104662] thermal_sys: Registered thermal governor 'fair_share'
[ 0.104675] thermal_sys: Registered thermal governor 'step_wise'
[ 0.104702] thermal_sys: Registered thermal governor 'user_space'
[ 0.104820] cpuidle: using governor menu
[ 0.105080] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.105269] ASID allocator initialised with 32768 entries
[ 0.105864] Serial: AMBA PL011 UART driver
[ 0.114972] /soc/bus@ff600000/hdmi-tx@0: Fixed dependency cycle(s) with /soc/vpu@ff900000
[ 0.115512] /soc/vpu@ff900000: Fixed dependency cycle(s) with /soc/bus@ff600000/hdmi-tx@0
[ 0.115559] /soc/interrupt-controller@ffc01000: Fixed dependency cycle(s) with /soc/interrupt-controller@ffc01000
[ 0.116516] /soc/bus@ff600000/hdmi-tx@0: Fixed dependency cycle(s) with /soc/vpu@ff900000
[ 0.117194] /soc/bus@ff600000/hdmi-tx@0: Fixed dependency cycle(s) with /soc/vpu@ff900000
[ 0.129921] /soc/bus@ff600000/hdmi-tx@0: Fixed dependency cycle(s) with /soc/vpu@ff900000
[ 0.130036] /soc/vpu@ff900000: Fixed dependency cycle(s) with /soc/bus@ff600000/hdmi-tx@0
[ 0.134936] /soc/vpu@ff900000: Fixed dependency cycle(s) with /cvbs-connector
[ 0.135062] /cvbs-connector: Fixed dependency cycle(s) with /soc/vpu@ff900000
[ 0.135600] /soc/bus@ff600000/hdmi-tx@0: Fixed dependency cycle(s) with /hdmi-connector
[ 0.135705] /hdmi-connector: Fixed dependency cycle(s) with /soc/bus@ff600000/hdmi-tx@0
[ 0.140927] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages
[ 0.140969] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page
[ 0.140987] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages
[ 0.141002] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page
[ 0.141018] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.141033] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page
[ 0.141048] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages
[ 0.141062] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page
[ 0.142607] cryptd: max_cpu_qlen set to 1000
[ 0.143575] raid6: skipped pq benchmark and selected neonx8
[ 0.143608] raid6: using neon recovery algorithm
[ 0.144259] fbcon: Taking over console
[ 0.144302] ACPI: Interpreter disabled.
[ 0.146680] iommu: Default domain type: Translated
[ 0.146716] iommu: DMA domain TLB invalidation policy: lazy mode
[ 0.150311] SCSI subsystem initialized
[ 0.150876] usbcore: registered new interface driver usbfs
[ 0.150933] usbcore: registered new interface driver hub
[ 0.150982] usbcore: registered new device driver usb
[ 0.151412] pps_core: LinuxPPS API ver. 1 registered
[ 0.151431] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.151461] PTP clock support registered
[ 0.151901] EDAC MC: Ver: 3.0.0
[ 0.152278] scmi_core: SCMI protocol bus registered
[ 0.152374] efivars: Registered efivars operations
[ 0.154996] NetLabel: Initializing
[ 0.155033] NetLabel: domain hash size = 128
[ 0.155047] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
[ 0.155181] NetLabel: unlabeled traffic allowed by default
[ 0.155217] mctp: management component transport protocol core
[ 0.155234] NET: Registered PF_MCTP protocol family
[ 0.155754] vgaarb: loaded
[ 0.156564] clocksource: Switched to clocksource arch_sys_counter
[ 0.402649] VFS: Disk quotas dquot_6.6.0
[ 0.402721] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.403353] pnp: PnP ACPI: disabled
[ 0.413000] NET: Registered PF_INET protocol family
[ 0.413351] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.478423] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
[ 0.478549] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.478709] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 0.479119] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear)
[ 0.479805] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.480220] MPTCP token hash table entries: 4096 (order: 4, 98304 bytes, linear)
[ 0.480362] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 0.480451] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 0.480681] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.480729] NET: Registered PF_XDP protocol family
[ 0.480756] PCI: CLS 0 bytes, default 64
[ 0.481030] Trying to unpack rootfs image as initramfs...
[ 0.485171] kvm [1]: nv: 554 coarse grained trap handlers
[ 0.485666] kvm [1]: IPA Size Limit: 40 bits
[ 0.485782] kvm [1]: vgic interrupt IRQ9
[ 0.485844] kvm [1]: VHE mode initialized successfully
[ 0.637804] Initialise system trusted keyrings
[ 0.637892] Key type blacklist registered
[ 0.638262] workingset: timestamp_bits=37 max_order=20 bucket_order=0
[ 0.638394] zbud: loaded
[ 0.639989] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled
[ 0.641168] integrity: Platform Keyring initialized
[ 0.641219] integrity: Machine keyring initialized
[ 0.695731] NET: Registered PF_ALG protocol family
[ 0.695813] xor: measuring software checksum speed
[ 0.697220] 8regs : 2363 MB/sec
[ 0.698593] 32regs : 2449 MB/sec
[ 0.699954] arm64_neon : 2457 MB/sec
[ 0.699988] xor: using function: arm64_neon (2457 MB/sec)
[ 0.700016] Key type asymmetric registered
[ 0.700032] Asymmetric key parser 'x509' registered
[ 0.700186] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
[ 0.700498] io scheduler mq-deadline registered
[ 0.700520] io scheduler kyber registered
[ 0.700574] io scheduler bfq registered
[ 0.701866] atomic64_test: passed
[ 0.703774] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized
[ 0.718273] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.738868] soc soc0: Amlogic Meson SM1 (S905D3) Revision 2b:c (4:2) Detected
[ 0.745747] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 0.761901] ff803000.serial: ttyAML0 at MMIO 0xff803000 (irq = 14, base_baud = 1500000) is a meson_uart
[ 0.761980] printk: legacy console [ttyAML0] enabled
[ 1.132100] Freeing initrd memory: 13572K
[ 1.140555] msm_serial: driver initialized
[ 2.147559] SuperH (H)SCI(F) driver initialized
[ 2.158377] usbcore: registered new interface driver usbserial_generic
[ 2.159313] usbserial: USB Serial support registered for generic
[ 2.165505] mousedev: PS/2 mouse device common for all mice
[ 2.173711] device-mapper: core: CONFIG_IMA_DISABLE_HTABLE is disabled. Duplicate IMA measurements will not be recorded in the IMA log.
[ 2.183020] device-mapper: uevent: version 1.0.3
[ 2.187877] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev
[ 2.198956] meson-sm: secure-monitor enabled
[ 2.201844] hid: raw HID events driver (C) Jiri Kosina
[ 2.205939] usbcore: registered new interface driver usbhid
[ 2.211309] usbhid: USB HID core driver
[ 2.219147] drop_monitor: Initializing network drop monitor service
[ 2.221663] Initializing XFRM netlink socket
[ 2.225717] NET: Registered PF_INET6 protocol family
[ 2.252261] Segment Routing with IPv6
[ 2.252318] RPL Segment Routing with IPv6
[ 2.254381] In-situ OAM (IOAM) with IPv6
[ 2.258286] mip6: Mobile IPv6
[ 2.261173] NET: Registered PF_PACKET protocol family
[ 2.278191] registered taskstats version 1
[ 2.279198] Loading compiled-in X.509 certificates
[ 2.284044] Loaded X.509 cert 'Gentoo Linux: Distribution Kernel Signing Key: c3aaa779efbdcf321e7d5b89033ee251722fd93b'
[ 2.319793] Demotion targets for Node 0: null
[ 2.319908] page_owner is disabled
[ 2.322289] Key type .fscrypt registered
[ 2.325835] Key type fscrypt-provisioning registered
[ 2.333813] Btrfs loaded, zoned=yes, fsverity=yes
[ 2.335563] Key type big_key registered
[ 2.339342] Key type encrypted registered
[ 2.343498] ima: secureboot mode disabled
[ 2.347270] ima: No TPM chip found, activating TPM-bypass!
[ 2.352740] Loading compiled-in module X.509 certificates
[ 2.360278] Loaded X.509 cert 'Gentoo Linux: Distribution Kernel Signing Key: c3aaa779efbdcf321e7d5b89033ee251722fd93b'
[ 2.368852] ima: Allocated hash algorithm: sha256
[ 2.373566] ima: No architecture policies found
[ 2.378101] evm: Initialising EVM extended attributes:
[ 2.383115] evm: security.selinux
[ 2.386405] evm: security.SMACK64 (disabled)
[ 2.390660] evm: security.SMACK64EXEC (disabled)
[ 2.395244] evm: security.SMACK64TRANSMUTE (disabled)
[ 2.400279] evm: security.SMACK64MMAP (disabled)
[ 2.404865] evm: security.apparmor
[ 2.408242] evm: security.ima
[ 2.411204] evm: security.capability
[ 2.414743] evm: HMAC attrs: 0x1
[ 2.542320] clk: Disabling unused clocks
[ 2.542571] PM: genpd: Disabling unused power domains
[ 2.560794] Freeing unused kernel memory: 13440K
[ 2.623555] Checked W+X mappings: passed, no W+X pages found
[ 2.623659] Run /init as init process
[ 2.645377] systemd[1]: System time before build time, advancing clock.
[ 2.669201] systemd[1]: Successfully made /usr/ read-only.
[ 2.680020] systemd[1]: systemd 256.10 running in system mode (+PAM -AUDIT -SELINUX -APPARMOR +IMA +SMACK +SECCOMP +GCRYPT -GNUTLS +OPENSSL +ACL +BLKID -CURL -ELFUTILS -FIDO2 +IDN2 -IDN -IPTC +KMOD -LIBCRYPTSETUP -LIBCRYPTSETUP_PLUGINS +LIBFDISK +PCRE2 -PWQUALITY -P11KIT -QRENCODE -TPM2 -BZIP2 +LZ4 -XZ -ZLIB +ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP -SYSVINIT -LIBARCHIVE)
[ 2.707043] systemd[1]: Detected architecture arm64.
[ 2.711901] systemd[1]: Running in initrd.
Welcome to dracut!
[ 2.726879] systemd[1]: Hostname set to <solitudepi>.
[ 3.027141] systemd[1]: Queued start job for default target Initrd Default Target.
[ 3.072783] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ OK ] Started Dispatch Password Requests to Console Directory Watch.
[ 3.093435] systemd[1]: Expecting device /dev/disk/by-uuid/8E33-D949...
Expecting device /dev/disk/by-uuid/8E33-D949...
[ 3.110025] systemd[1]: Expecting device /dev/disk/by-uuid/a39c0ab6-c7fb-4958-b691-178604eaa03d...
Expecting device /dev/disk/by-uuid…0ab6-c7fb-4958-b691-178604eaa03d...
[ 3.130140] systemd[1]: Reached target Initrd /usr File System.
[ OK ] Reached target Initrd /usr File System.
[ 3.146755] systemd[1]: Reached target Path Units.
[ OK ] Reached target Path Units.
[ 3.160086] systemd[1]: Reached target Slice Units.
[ OK ] Reached target Slice Units.
[ 3.173434] systemd[1]: Reached target Swaps.
[ OK ] Reached target Swaps.
[ 3.186754] systemd[1]: Reached target Timer Units.
[ OK ] Reached target Timer Units.
[ 3.200644] systemd[1]: Listening on Journal Socket (/dev/log).
[ OK ] Listening on Journal Socket (/dev/log).
[ 3.217244] systemd[1]: Listening on Journal Sockets.
[ OK ] Listening on Journal Sockets.
[ 3.230598] systemd[1]: Listening on udev Control Socket.
[ OK ] Listening on udev Control Socket.
[ 3.243789] systemd[1]: Listening on udev Kernel Socket.
[ OK ] Listening on udev Kernel Socket.
[ 3.256764] systemd[1]: Reached target Socket Units.
[ OK ] Reached target Socket Units.
[ 3.275989] systemd[1]: Starting Create List of Static Device Nodes...
Starting Create List of Static Device Nodes...
[ 3.293760] systemd[1]: Check battery level during early boot was skipped because of an unmet condition check (ConditionDirectoryNotEmpty=/sys/class/power_supply).
[ 3.344297] systemd[1]: Starting Journal Service...
Starting Journal Service...
[ 3.360784] systemd[1]: Load Kernel Modules was skipped because no trigger condition checks were met.
[ 3.368461] systemd[1]: Starting Apply Kernel Variables...
Starting Apply Kernel Variables...
[ 3.430305] systemd[1]: Starting Virtual Console Setup...
Starting Virtual Console Setup...
[ 3.451104] systemd[1]: Finished Create List of Static Device Nodes.
[ OK ] Finished Create List of Static Device Nodes.
[ 3.473435] systemd[1]: Finished Apply Kernel Variables.
[ OK ] Finished 3.478617] systemd[1]: Starting Create Static Device Nodes in /dev gracefully...
mApply Kernel Variables.
Starting Create Static Device Nodes in /dev gracefu[ 3.493197] systemd-journald[123]: Collecting audit messages is disabled.
lly...
[ 3.523773] systemd[1]: Finished Virtual Console Setup.
[ OK ] Finished Virtual Console Setup.
[ 3.538715] systemd[1]: Started Journal Service.
[ OK ] Started Journal Service.
Starting dracut ask for additional cmdline parameters...
[ OK ] Finished Create Static Device Nodes in /dev gracefully.
Starting Create Static Device Nodes in /dev...
[ OK ] Finished dracut ask for additional cmdline parameters.
Starting dracut cmdline hook...
[ OK ] Finished Create Static Device Nodes in /dev.
[ OK ] Reached target Preparation for Local File Systems.
[ OK ] Reached target Local File Systems.
Starting Create System Files and Directories...
[ OK ] Finished dracut cmdline hook.
Starting dracut pre-udev hook...
[ OK ] Finished Create System Files and Directories.
[ OK ] Finished dracut pre-udev hook.
Starting Rule-based Manager for Device Events and Files...
[ OK ] Started Rule-based Manager for Device Events and Files.
Starting Coldplug All udev Devices...
[ OK ] Created slice Slice /system/modprobe.
Starting Load Kernel Module configfs...
[ OK ] Finished Coldplug All udev Devices.
[ OK ] Finished Load Kernel Module configfs.
Mounting Kernel Configuration File System...
Starting dracut initqueue hook...
[ OK ] Mounted Kernel Configuration File System.
[ OK ] Reached target System Initialization.
[ OK ] Reached target Basic System.
[ 5.468605] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
[ 5.581396] meson-vrtc ff8000a8.rtc: registered as rtc0
[ 5.581523] meson-vrtc ff8000a8.rtc: setting system clock to 2024-12-20T19:47:28 UTC (1734724048)
[ 5.596910] systemd-journald[123]: Time jumped backwards, rotating.
[ 5.673754] meson-gx-mmc ffe05000.mmc: Got CD GPIO
[ 5.674576] meson-gx-mmc ffe07000.mmc: allocated mmc-pwrseq
[ 5.676994] dwc3-meson-g12a ffe09000.usb: USB2 ports: 2
[ 5.683785] dwc3-meson-g12a ffe09000.usb: USB3 ports: 1
[ OK ] Stopped Virtual Console Setup.
Stopping Virtual Console Setup...
Starting Virtual Console Setup...
[ 5.815503] dwc2 ff400000.usb: supply vusb_d not found, using dummy regulator
[ 5.819590] dwc2 ff400000.usb: supply vusb_a not found, using dummy regulator
[ 5.824732] dwc2 ff400000.usb: EPs: 7, dedicated fifos, 712 entries in SPRAM
[ 5.845251] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 5.845654] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1
[ 5.853097] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228fe6c hci version 0x110 quirks 0x0000808000000010
[ 5.862237] xhci-hcd xhci-hcd.1.auto: irq 19, io mem 0xff500000
[ 5.868264] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 5.874027] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2
[ 5.881303] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 5.887955] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.12
[ 5.895866] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.903054] usb usb1: Product: xHCI Host Controller
[ 5.907898] usb usb1: Manufacturer: Linux 6.12.21-gentoo-dist xhci-hcd
[ 5.914389] usb usb1: SerialNumber: xhci-hcd.1.auto
[ 5.919962] hub 1-0:1.0: USB hub found
[ 5.923080] hub 1-0:1.0: 2 ports detected
[ 5.927708] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 5.935253] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.12
[ 5.943269] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.950459] usb usb2: Product: xHCI Host Controller
[ 5.950468] usb usb2: Manufacturer: Linux 6.12.21-gentoo-dist xhci-hcd
[ 5.950475] usb usb2: SerialNumber: xhci-hcd.1.auto
[ 5.951293] hub 2-0:1.0: USB hub found
[ 5.970543] hub 2-0:1.0: 1 port detected
[ OK ] Finished Virtual Console Setup.
[ 6.134472] mmc1: new ultra high speed SDR104 SDXC card at address aaaa
[ 6.169929] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 6.302410] usb 1-1: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice= 6.63
[ 6.305002] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 6.312106] usb 1-1: Product: USB2.1 Hub
[ 6.316004] usb 1-1: Manufacturer: GenesysLogic
[ 6.368103] hub 1-1:1.0: USB hub found
[ 6.368606] hub 1-1:1.0: 4 ports detected
[ 6.390200] usbcore: registered new device driver onboard-usb-dev
[ 6.416906] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 6.437238] usb 2-1: New USB device found, idVendor=05e3, idProduct=0626, bcdDevice= 6.63
[ 6.439802] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 6.446935] usb 2-1: Product: USB3.1 Hub
[ 6.450825] usb 2-1: Manufacturer: GenesysLogic
[ 6.480869] hub 2-1:1.0: USB hub found
[ 6.481755] hub 2-1:1.0: 4 ports detected
[ 6.669974] usb 1-1.4: new full-speed USB device number 3 using xhci-hcd
[ 6.788451] usb 1-1.4: New USB device found, idVendor=062a, idProduct=4c01, bcdDevice= 1.25
[ 6.791219] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 6.798494] usb 1-1.4: Product: 2.4G INPUT DEVICE
[ 6.803182] usb 1-1.4: Manufacturer: MOSART Semi.
[ 6.880164] usb 2-1.2: new SuperSpeed USB device number 3 using xhci-hcd
[ 6.882838] input: MOSART Semi. 2.4G INPUT DEVICE as /devices/platform/soc/ffe09000.usb/ff500000.usb/xhci-hcd.1.auto/usb1/1-1/1-1.4/1-1.4:1.0/0003:062A:4C01.0001/input/input1
[ 6.901997] usb 2-1.2: New USB device found, idVendor=05e3, idProduct=0749, bcdDevice=15.39
[ 6.905112] usb 2-1.2: New USB device strings: Mfr=3, Product=4, SerialNumber=5
[ 6.912388] usb 2-1.2: Product: USB3.0 Card Reader
[ 6.917151] usb 2-1.2: Manufacturer: Generic
[ 6.921392] usb 2-1.2: SerialNumber: 000000001539
[ 6.945177] usb-storage 2-1.2:1.0: USB Mass Storage device detected
[ 6.946628] scsi host0: usb-storage 2-1.2:1.0
[ 6.950869] usbcore: registered new interface driver usb-storage
[ 6.961147] usbcore: registered new interface driver uas
[ 7.037075] hid-generic 0003:062A:4C01.0001: input,hidraw0: USB HID v1.10 Keyboard [MOSART Semi. 2.4G INPUT DEVICE] on usb-xhci-hcd.1.auto-1.4/input0
[ 7.050268] input: MOSART Semi. 2.4G INPUT DEVICE Mouse as /devices/platform/soc/ffe09000.usb/ff500000.usb/xhci-hcd.1.auto/usb1/1-1/1-1.4/1-1.4:1.1/0003:062A:4C01.0002/input/input2
[ 7.061529] input: MOSART Semi. 2.4G INPUT DEVICE Consumer Control as /devices/platform/soc/ffe09000.usb/ff500000.usb/xhci-hcd.1.auto/usb1/1-1/1-1.4/1-1.4:1.1/0003:062A:4C01.0002/input/input3
[ 7.130279] input: MOSART Semi. 2.4G INPUT DEVICE System Control as /devices/platform/soc/ffe09000.usb/ff500000.usb/xhci-hcd.1.auto/usb1/1-1/1-1.4/1-1.4:1.1/0003:062A:4C01.0002/input/input4
[ 7.141861] input: MOSART Semi. 2.4G INPUT DEVICE as /devices/platform/soc/ffe09000.usb/ff500000.usb/xhci-hcd.1.auto/usb1/1-1/1-1.4/1-1.4:1.1/0003:062A:4C01.0002/input/input5
[ 7.158011] hid-generic 0003:062A:4C01.0002: input,hiddev96,hidraw1: USB HID v1.10 Mouse [MOSART Semi. 2.4G INPUT DEVICE] on usb-xhci-hcd.1.auto-1.4/input1
[ 7.975503] scsi 0:0:0:0: Direct-Access Generic MassStorageClass 1539 PQ: 0 ANSI: 6
[ 7.979670] scsi 0:0:0:1: Direct-Access Generic MassStorageClass 1539 PQ: 0 ANSI: 6
[ 7.987130] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 7.988513] sd 0:0:0:0: [sda] Media removed, stopped polling
[ 7.996698] sd 0:0:0:1: Attached scsi generic sg1 type 0
[ 7.998215] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 8.196854] sd 0:0:0:1: [sdb] Media removed, stopped polling
[ 8.197997] sd 0:0:0:1: [sdb] Attached SCSI removable disk
[ 146.737913] dracut-initqueue[252]: Warning: dracut-initqueue: timeout, still waiting for following initqueue hooks:
[ 146.754056] dracut-initqueue[252]: Warning: /lib/dracut/hooks/initqueue/finished/devexists-\x2fdev\x2fdisk\x2fby-uuid\x2f8E33-D949.sh: "[ -e "/dev/disk/by-uuid/8E33-D949" ]"
[ 146.773744] dracut-initqueue[252]: Warning: /lib/dracut/hooks/initqueue/finished/devexists-\x2fdev\x2fdisk\x2fby-uuid\x2fa39c0ab6-c7fb-4958-b691-178604eaa03d.sh: "if ! grep -q After=remote-fs-pre.target /run/systemd/generator/systemd-cryptsetup@*.service 2>/dev/null; then
[ 146.803663] dracut-initqueue[252]: [ -e "/dev/disk/by-uuid/a39c0ab6-c7fb-4958-b691-178604eaa03d" ]
[ 146.816961] dracut-initqueue[252]: fi"
[ 146.827032] dracut-initqueue[252]: Warning: dracut-initqueue: starting timeout scripts
[ 147.363847] dracut-initqueue[252]: Warning: dracut-initqueue: timeout, still waiting for following initqueue hooks:
[ 147.377118] dracut-initqueue[252]: Warning: /lib/dracut/hooks/initqueue/finished/devexists-\x2fdev\x2fdisk\x2fby-uuid\x2f8E33-D949.sh: "[ -e "/dev/disk/by-uuid/8E33-D949" ]"
[ 147.400315] dracut-initqueue[252]: Warning: /lib/dracut/hooks/initqueue/finished/devexists-\x2fdev\x2fdisk\x2fby-uuid\x2fa39c0ab6-c7fb-4958-b691-178604eaa03d.sh: "if ! grep -q After=remote-fs-pre.target /run/systemd/generator/systemd-cryptsetup@*.service 2>/dev/null; then
[ 147.430266] dracut-initqueue[252]: [ -e "/dev/disk/by-uuid/a39c0ab6-c7fb-4958-b691-178604eaa03d" ]
[ 147.443642] dracut-initqueue[252]: fi"
[ 147.453737] dracut-initqueue[252]: Warning: dracut-initqueue: starting timeout scripts
[ 147.957108] dracut-initqueue[252]: Warning: dracut-initqueue: timeout, still waiting for following initqueue hooks:
[ 147.973714] dracut-initqueue[252]: Warning: /lib/dracut/hooks/initqueue/finished/devexists-\x2fdev\x2fdisk\x2fby-uuid\x2f8E33-D949.sh: "[ -e "/dev/disk/by-uuid/8E33-D949" ]"
[ 147.993687] dracut-initqueue[252]: Warning: /lib/dracut/hooks/initqueue/finished/devexists-\x2fdev\x2fdisk\x2fby-uuid\x2fa39c0ab6-c7fb-4958-b691-178604eaa03d.sh: "if ! grep -q After=remote-fs-pre.target /run/systemd/generator/systemd-cryptsetup@*.service 2>/dev/null; then
[ 148.023653] dracut-initqueue[252]: [ -e "/dev/disk/by-uuid/a39c0ab6-c7fb-4958-b691-178604eaa03d" ]
[ 148.036973] dracut-initqueue[252]: fi"
[ 148.050272] dracut-initqueue[252]: Warning: dracut-initqueue: starting timeout scripts
[ 148.547447] dracut-initqueue[252]: Warning: dracut-initqueue: timeout, still waiting for following initqueue hooks:
[ 148.560421] dracut-initqueue[252]: Warning: /lib/dracut/hooks/initqueue/finished/devexists-\x2fdev\x2fdisk\x2fby-uuid\x2f8E33-D949.sh: "[ -e "/dev/disk/by-uuid/8E33-D949" ]"
[ 148.580373] dracut-initqueue[252]: Warning: /lib/dracut/hooks/initqueue/finished/devexists-\x2fdev\x2fdisk\x2fby-uuid\x2fa39c0ab6-c7fb-4958-b691-178604eaa03d.sh: "if ! grep -q After=remote-fs-pre.target /run/systemd/generator/systemd-cryptsetup@*.service 2>/dev/null; then
[ 148.610336] dracut-initqueue[252]: [ -e "/dev/disk/by-uuid/a39c0ab6-c7fb-4958-b691-178604eaa03d" ]
[ 148.623667] dracut-initqueue[252]: fi"
[ 148.633686] dracut-initqueue[252]: Warning: dracut-initqueue: starting timeout scripts
[ 149.140766] dracut-initqueue[252]: Warning: dracut-initqueue: timeout, still waiting for following initqueue hooks:
[ 149.157052] dracut-initqueue[252]: Warning: /lib/dracut/hooks/initqueue/finished/devexists-\x2fdev\x2fdisk\x2fby-uuid\x2f8E33-D949.sh: "[ -e "/dev/disk/by-uuid/8E33-D949" ]"
[ 149.176983] dracut-initqueue[252]: Warning: /lib/dracut/hooks/initqueue/finished/devexists-\x2fdev\x2fdisk\x2fby-uuid\x2fa39c0ab6-c7fb-4958-b691-178604eaa03d.sh: "if ! grep -q After=remote-fs-pre.target /run/systemd/generator/systemd-cryptsetup@*.service 2>/dev/null; then
[ 149.206914] dracut-initqueue[252]: [ -e "/dev/disk/by-uuid/a39c0ab6-c7fb-4958-b691-178604eaa03d" ]
[ 149.220331] dracut-initqueue[252]: fi"
[ 149.230330] dracut-initqueue[252]: Warning: dracut-initqueue: starting timeout scripts
|
Last edited by JumboAg on Thu Apr 24, 2025 10:25 pm; edited 1 time in total |
|
| Back to top |
|
 |
pingtoo
Veteran
Joined: 10 Sep 2021
Posts: 1684
Location: Richmond Hill, Canada
|
| Posted: Sat Apr 19, 2025 10:01 am Post subject: |
|
|
u-boot and UEFI, two topics I am very interesting learning. u-boot something I play a bit in the past. UEFI I just start learning more about it.
May I joint to explore this? |
|
| Back to top |
|
|
JumboAg
Apprentice
Joined: 03 Mar 2007
Posts: 220
Location: Dallas, TX
|
| Posted: Sun Apr 20, 2025 1:45 am Post subject: |
|
|
Update: I'm pretty sure I've confirmed what my problem is, I just cannot fix it. I CAN boot the micro SD card off a USB reader and get into Gentoo fine (dmesg from that posted below). I cannot use the same card in the built in SD reader. My guess is that I'm not getting what I need into the initramfs to load the built in mmcblk device. The drivers are there, they clearly load when I USB boot.
| Code: |
$ sudo dmesg
Password:
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x411fd050]
[ 0.000000] Linux version 6.12.21-gentoo-dist (root@dola.arm.dev.gentoo.org) (aarch64-unknown-linux-gnu-gcc (Gentoo 14.2.1_p20241221 p7) 14.2.1 20241221, GNU ld (Gentoo 2.44 p1) 2.44.0) #1 SMP PREEMPT_DYNAMIC Sat Mar 29 11:37:58 -00 2025
[ 0.000000] KASLR enabled
[ 0.000000] Machine model: Libre Computer AML-S905D3-CC
[ 0.000000] efi: EFI v2.10 by Das U-Boot
[ 0.000000] efi: RTPROP=0xe9e7f040 SMBIOS=0xe9e7e000 INITRD=0xe6bb4040 RNG=0xe56f8040 MEMRESERVE=0xe56f7040
[ 0.000000] random: crng init done
[ 0.000000] Reserved memory: created CMA memory pool at 0x00000000d4400000, size 256 MiB
[ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[ 0.000000] OF: reserved mem: 0x00000000d4400000..0x00000000e43fffff (262144 KiB) map reusable linux,cma
[ 0.000000] OF: reserved mem: 0x0000000005000000..0x00000000052fffff (3072 KiB) nomap non-reusable secmon@5000000
[ 0.000000] OF: reserved mem: 0x0000000005300000..0x00000000072fffff (32768 KiB) nomap non-reusable secmon@5300000
[ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x00000000f4ffffff]
[ 0.000000] NODE_DATA(0) allocated [mem 0xf3d1c200-0xf3d32f3f]
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000000000-0x00000000f4ffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Device empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000004ffffff]
[ 0.000000] node 0: [mem 0x0000000005000000-0x00000000072fffff]
[ 0.000000] node 0: [mem 0x0000000007300000-0x00000000e9e7dfff]
[ 0.000000] node 0: [mem 0x00000000e9e7e000-0x00000000e9e7ffff]
[ 0.000000] node 0: [mem 0x00000000e9e80000-0x00000000e9e80fff]
[ 0.000000] node 0: [mem 0x00000000e9e81000-0x00000000e9e86fff]
[ 0.000000] node 0: [mem 0x00000000e9e87000-0x00000000f2e9ffff]
[ 0.000000] node 0: [mem 0x00000000f2ea0000-0x00000000f2eaffff]
[ 0.000000] node 0: [mem 0x00000000f2eb0000-0x00000000f4725fff]
[ 0.000000] node 0: [mem 0x00000000f4726000-0x00000000f4ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00000000f4ffffff]
[ 0.000000] On node 0, zone DMA: 12288 pages in unavailable ranges
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.1
[ 0.000000] percpu: Embedded 56 pages/cpu s104600 r8192 d116584 u229376
[ 0.000000] pcpu-alloc: s104600 r8192 d116584 u229376 alloc=56*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: Virtualization Host Extensions
[ 0.000000] CPU features: kernel page table isolation forced ON by KASLR
[ 0.000000] CPU features: detected: Kernel page table isolation (KPTI)
[ 0.000000] CPU features: detected: Qualcomm erratum 1009, or ARM erratum 1286807, 2441009
[ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[ 0.000000] alternatives: applying boot alternatives
[ 0.000000] Kernel command line: BOOT_IMAGE=/kernel-6.12.21-gentoo-dist root=UUID=a39c0ab6-c7fb-4958-b691-178604eaa03d ro nomodeset
[ 0.000000] Booted with the nomodeset parameter. Only the system framebuffer will be available
[ 0.000000] Unknown kernel command line parameters "BOOT_IMAGE=/kernel-6.12.21-gentoo-dist", will be passed to user space.
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[ 0.000000] Fallback order for Node 0: 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1003520
[ 0.000000] Policy zone: DMA
[ 0.000000] mem auto-init: stack:all(zero), heap alloc:on, heap free:off
[ 0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 3MB
[ 0.000000] software IO TLB: area num 4.
[ 0.000000] software IO TLB: mapped [mem 0x00000000f31ca000-0x00000000f35ca000] (4MB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] ftrace: allocating 68944 entries in 270 pages
[ 0.000000] ftrace: allocated 270 pages with 4 groups
[ 0.000000] Dynamic Preempt: voluntary
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=4.
[ 0.000000] Trampoline variant of Tasks RCU enabled.
[ 0.000000] Rude variant of Tasks RCU enabled.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] RCU Tasks: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
[ 0.000000] RCU Tasks Rude: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
[ 0.000000] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] Root IRQ handler: gic_handle_irq
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000000] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.000510] kfence: initialized - using 2097152 bytes for 255 objects at 0x(____ptrval____)-0x(____ptrval____)
[ 0.000706] Console: colour dummy device 80x25
[ 0.000721] printk: legacy console [tty0] enabled
[ 0.001545] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[ 0.001577] pid_max: default: 32768 minimum: 301
[ 0.001789] LSM: initializing lsm=lockdown,capability,yama,ima,evm
[ 0.001899] Yama: becoming mindful.
[ 0.002127] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.002164] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.003745] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.020039] rcu: Hierarchical SRCU implementation.
[ 0.020078] rcu: Max phase no-delay instances is 1000.
[ 0.020385] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level
[ 0.023491] Remapping and enabling EFI services.
[ 0.024007] smp: Bringing up secondary CPUs ...
[ 0.033989] Detected VIPT I-cache on CPU1
[ 0.034077] CPU1: Booted secondary processor 0x0000000100 [0x411fd050]
[ 0.047377] Detected VIPT I-cache on CPU2
[ 0.047456] CPU2: Booted secondary processor 0x0000000200 [0x411fd050]
[ 0.060757] Detected VIPT I-cache on CPU3
[ 0.060835] CPU3: Booted secondary processor 0x0000000300 [0x411fd050]
[ 0.061042] smp: Brought up 1 node, 4 CPUs
[ 0.061121] SMP: Total of 4 processors activated.
[ 0.061135] CPU: All CPU(s) started at EL2
[ 0.061148] CPU features: detected: 32-bit EL0 Support
[ 0.061161] CPU features: detected: 32-bit EL1 Support
[ 0.061176] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[ 0.061194] CPU features: detected: Common not Private translations
[ 0.061208] CPU features: detected: CRC32 instructions
[ 0.061221] CPU features: detected: Data cache clean to Point of Persistence
[ 0.061242] CPU features: detected: RCpc load-acquire (LDAPR)
[ 0.061256] CPU features: detected: LSE atomic instructions
[ 0.061270] CPU features: detected: Privileged Access Never
[ 0.061284] CPU features: detected: RAS Extension Support
[ 0.061353] alternatives: applying system-wide alternatives
[ 0.066280] Memory: 3539868K/4014080K available (22208K kernel code, 5532K rwdata, 18040K rodata, 13440K init, 1485K bss, 204940K reserved, 262144K cma-reserved)
[ 0.067766] devtmpfs: initialized
[ 0.082017] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[ 0.082087] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.089061] 2G module region forced by RANDOMIZE_MODULE_REGION_FULL
[ 0.089111] 0 pages in range for non-PLT usage
[ 0.089116] 509056 pages in range for PLT usage
[ 0.089493] pinctrl core: initialized pinctrl subsystem
[ 0.092412] SMBIOS 3.0 present.
[ 0.092452] DMI: libre-computer aml-s905d3-cc/aml-s905d3-cc, BIOS 2023.07+ 07/01/2023
[ 0.092483] DMI: Memory slots populated: 0/0
[ 0.095526] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.097375] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations
[ 0.098094] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.099416] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.099549] audit: initializing netlink subsys (disabled)
[ 0.099865] audit: type=2000 audit(0.096:1): state=initialized audit_enabled=0 res=1
[ 0.101635] thermal_sys: Registered thermal governor 'fair_share'
[ 0.101649] thermal_sys: Registered thermal governor 'step_wise'
[ 0.101672] thermal_sys: Registered thermal governor 'user_space'
[ 0.101775] cpuidle: using governor menu
[ 0.102037] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.102211] ASID allocator initialised with 32768 entries
[ 0.102847] Serial: AMBA PL011 UART driver
[ 0.111970] /soc/bus@ff600000/hdmi-tx@0: Fixed dependency cycle(s) with /soc/vpu@ff900000
[ 0.112508] /soc/vpu@ff900000: Fixed dependency cycle(s) with /soc/bus@ff600000/hdmi-tx@0
[ 0.112553] /soc/interrupt-controller@ffc01000: Fixed dependency cycle(s) with /soc/interrupt-controller@ffc01000
[ 0.113499] /soc/bus@ff600000/hdmi-tx@0: Fixed dependency cycle(s) with /soc/vpu@ff900000
[ 0.114163] /soc/bus@ff600000/hdmi-tx@0: Fixed dependency cycle(s) with /soc/vpu@ff900000
[ 0.126834] /soc/bus@ff600000/hdmi-tx@0: Fixed dependency cycle(s) with /soc/vpu@ff900000
[ 0.126950] /soc/vpu@ff900000: Fixed dependency cycle(s) with /soc/bus@ff600000/hdmi-tx@0
[ 0.131826] /soc/vpu@ff900000: Fixed dependency cycle(s) with /cvbs-connector
[ 0.131947] /cvbs-connector: Fixed dependency cycle(s) with /soc/vpu@ff900000
[ 0.132486] /soc/bus@ff600000/hdmi-tx@0: Fixed dependency cycle(s) with /hdmi-connector
[ 0.132594] /hdmi-connector: Fixed dependency cycle(s) with /soc/bus@ff600000/hdmi-tx@0
[ 0.137790] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages
[ 0.137832] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page
[ 0.137850] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages
[ 0.137865] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page
[ 0.137881] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.137895] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page
[ 0.137910] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages
[ 0.137924] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page
[ 0.139475] cryptd: max_cpu_qlen set to 1000
[ 0.140448] raid6: skipped pq benchmark and selected neonx8
[ 0.140478] raid6: using neon recovery algorithm
[ 0.141117] fbcon: Taking over console
[ 0.141184] ACPI: Interpreter disabled.
[ 0.143516] iommu: Default domain type: Translated
[ 0.143552] iommu: DMA domain TLB invalidation policy: lazy mode
[ 0.147155] SCSI subsystem initialized
[ 0.147512] libata version 3.00 loaded.
[ 0.147738] usbcore: registered new interface driver usbfs
[ 0.147801] usbcore: registered new interface driver hub
[ 0.147852] usbcore: registered new device driver usb
[ 0.148289] pps_core: LinuxPPS API ver. 1 registered
[ 0.148307] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.148339] PTP clock support registered
[ 0.148798] EDAC MC: Ver: 3.0.0
[ 0.149162] scmi_core: SCMI protocol bus registered
[ 0.149262] efivars: Registered efivars operations
[ 0.151771] NetLabel: Initializing
[ 0.151807] NetLabel: domain hash size = 128
[ 0.151821] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
[ 0.151919] NetLabel: unlabeled traffic allowed by default
[ 0.151955] mctp: management component transport protocol core
[ 0.151971] NET: Registered PF_MCTP protocol family
[ 0.152510] vgaarb: loaded
[ 0.153431] clocksource: Switched to clocksource arch_sys_counter
[ 0.399775] VFS: Disk quotas dquot_6.6.0
[ 0.399855] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.400324] pnp: PnP ACPI: disabled
[ 0.409899] NET: Registered PF_INET protocol family
[ 0.410227] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.475463] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
[ 0.475591] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.475756] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 0.476162] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear)
[ 0.476903] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.477257] MPTCP token hash table entries: 4096 (order: 4, 98304 bytes, linear)
[ 0.477393] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 0.477481] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 0.477705] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.477752] NET: Registered PF_XDP protocol family
[ 0.477788] PCI: CLS 0 bytes, default 64
[ 0.478058] Trying to unpack rootfs image as initramfs...
[ 0.482150] kvm [1]: nv: 554 coarse grained trap handlers
[ 0.482663] kvm [1]: IPA Size Limit: 40 bits
[ 0.482788] kvm [1]: vgic interrupt IRQ9
[ 0.482865] kvm [1]: VHE mode initialized successfully
[ 0.634247] Initialise system trusted keyrings
[ 0.634337] Key type blacklist registered
[ 0.634707] workingset: timestamp_bits=37 max_order=20 bucket_order=0
[ 0.634852] zbud: loaded
[ 0.636448] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled
[ 0.637651] integrity: Platform Keyring initialized
[ 0.637700] integrity: Machine keyring initialized
[ 0.692490] NET: Registered PF_ALG protocol family
[ 0.692561] xor: measuring software checksum speed
[ 0.693962] 8regs : 2370 MB/sec
[ 0.695329] 32regs : 2449 MB/sec
[ 0.696643] arm64_neon : 2533 MB/sec
[ 0.696662] xor: using function: arm64_neon (2533 MB/sec)
[ 0.696689] Key type asymmetric registered
[ 0.696705] Asymmetric key parser 'x509' registered
[ 0.696925] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
[ 0.697282] io scheduler mq-deadline registered
[ 0.697304] io scheduler kyber registered
[ 0.697361] io scheduler bfq registered
[ 0.700503] atomic64_test: passed
[ 0.702227] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized
[ 0.716566] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.734878] soc soc0: Amlogic Meson SM1 (S905D3) Revision 2b:c (4:2) Detected
[ 0.740710] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 0.756215] ff803000.serial: ttyAML0 at MMIO 0xff803000 (irq = 14, base_baud = 1500000) is a meson_uart
[ 0.756288] printk: legacy console [ttyAML0] enabled
[ 1.123774] Freeing initrd memory: 13484K
[ 1.134786] msm_serial: driver initialized
[ 2.141882] SuperH (H)SCI(F) driver initialized
[ 2.153041] usbcore: registered new interface driver usbserial_generic
[ 2.154025] usbserial: USB Serial support registered for generic
[ 2.160169] mousedev: PS/2 mouse device common for all mice
[ 2.168040] device-mapper: core: CONFIG_IMA_DISABLE_HTABLE is disabled. Duplicate IMA measurements will not be recorded in the IMA log.
[ 2.177695] device-mapper: uevent: version 1.0.3
[ 2.182556] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev
[ 2.193469] meson-sm: secure-monitor enabled
[ 2.196383] hid: raw HID events driver (C) Jiri Kosina
[ 2.200615] usbcore: registered new interface driver usbhid
[ 2.205971] usbhid: USB HID core driver
[ 2.213676] drop_monitor: Initializing network drop monitor service
[ 2.216288] Initializing XFRM netlink socket
[ 2.220392] NET: Registered PF_INET6 protocol family
[ 2.247442] Segment Routing with IPv6
[ 2.247498] RPL Segment Routing with IPv6
[ 2.249541] In-situ OAM (IOAM) with IPv6
[ 2.253506] mip6: Mobile IPv6
[ 2.256337] NET: Registered PF_PACKET protocol family
[ 2.273267] registered taskstats version 1
[ 2.274259] Loading compiled-in X.509 certificates
[ 2.279234] Loaded X.509 cert 'Gentoo Linux: Distribution Kernel Signing Key: c3aaa779efbdcf321e7d5b89033ee251722fd93b'
[ 2.314616] Demotion targets for Node 0: null
[ 2.314697] page_owner is disabled
[ 2.317126] Key type .fscrypt registered
[ 2.320660] Key type fscrypt-provisioning registered
[ 2.328658] Btrfs loaded, zoned=yes, fsverity=yes
[ 2.330422] Key type big_key registered
[ 2.334139] Key type encrypted registered
[ 2.338322] ima: secureboot mode disabled
[ 2.342076] ima: No TPM chip found, activating TPM-bypass!
[ 2.347539] Loading compiled-in module X.509 certificates
[ 2.355061] Loaded X.509 cert 'Gentoo Linux: Distribution Kernel Signing Key: c3aaa779efbdcf321e7d5b89033ee251722fd93b'
[ 2.363664] ima: Allocated hash algorithm: sha256
[ 2.368403] ima: No architecture policies found
[ 2.372912] evm: Initialising EVM extended attributes:
[ 2.377949] evm: security.selinux
[ 2.381230] evm: security.SMACK64 (disabled)
[ 2.385475] evm: security.SMACK64EXEC (disabled)
[ 2.390078] evm: security.SMACK64TRANSMUTE (disabled)
[ 2.395101] evm: security.SMACK64MMAP (disabled)
[ 2.399689] evm: security.apparmor
[ 2.403068] evm: security.ima
[ 2.406025] evm: security.capability
[ 2.409581] evm: HMAC attrs: 0x1
[ 2.537661] clk: Disabling unused clocks
[ 2.537939] PM: genpd: Disabling unused power domains
[ 2.555375] Freeing unused kernel memory: 13440K
[ 2.618058] Checked W+X mappings: passed, no W+X pages found
[ 2.618161] Run /init as init process
[ 2.621769] with arguments:
[ 2.621779] /init
[ 2.621786] with environment:
[ 2.621793] HOME=/
[ 2.621799] TERM=linux
[ 2.621805] BOOT_IMAGE=/kernel-6.12.21-gentoo-dist
[ 2.639890] systemd[1]: System time before build time, advancing clock.
[ 2.662541] systemd[1]: Successfully made /usr/ read-only.
[ 2.673562] systemd[1]: systemd 256.10 running in system mode (+PAM -AUDIT -SELINUX -APPARMOR +IMA +SMACK +SECCOMP +GCRYPT -GNUTLS +OPENSSL +ACL +BLKID -CURL -ELFUTILS -FIDO2 +IDN2 -IDN -IPTC +KMOD -LIBCRYPTSETUP -LIBCRYPTSETUP_PLUGINS +LIBFDISK +PCRE2 -PWQUALITY -P11KIT -QRENCODE -TPM2 -BZIP2 +LZ4 -XZ -ZLIB +ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP -SYSVINIT -LIBARCHIVE)
[ 2.700561] systemd[1]: Detected architecture arm64.
[ 2.705473] systemd[1]: Running in initrd.
[ 2.720418] systemd[1]: Hostname set to <solitudepi>.
[ 3.035690] systemd[1]: Queued start job for default target Initrd Default Target.
[ 3.099554] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 3.120287] systemd[1]: Expecting device /dev/disk/by-uuid/8E33-D949...
[ 3.136888] systemd[1]: Expecting device /dev/disk/by-uuid/a39c0ab6-c7fb-4958-b691-178604eaa03d...
[ 3.156976] systemd[1]: Reached target Initrd /usr File System.
[ 3.173648] systemd[1]: Reached target Path Units.
[ 3.186967] systemd[1]: Reached target Slice Units.
[ 3.200294] systemd[1]: Reached target Swaps.
[ 3.213601] systemd[1]: Reached target Timer Units.
[ 3.227476] systemd[1]: Listening on Journal Socket (/dev/log).
[ 3.244125] systemd[1]: Listening on Journal Sockets.
[ 3.257465] systemd[1]: Listening on udev Control Socket.
[ 3.270631] systemd[1]: Listening on udev Kernel Socket.
[ 3.283627] systemd[1]: Reached target Socket Units.
[ 3.302825] systemd[1]: Starting Create List of Static Device Nodes...
[ 3.320597] systemd[1]: Check battery level during early boot was skipped because of an unmet condition check (ConditionDirectoryNotEmpty=/sys/class/power_supply).
[ 3.337464] systemd[1]: Starting Journal Service...
[ 3.354465] systemd[1]: Load Kernel Modules was skipped because no trigger condition checks were met.
[ 3.390576] systemd[1]: Starting Apply Kernel Variables...
[ 3.407911] systemd[1]: Starting Virtual Console Setup...
[ 3.431103] systemd[1]: Finished Create List of Static Device Nodes.
[ 3.457201] systemd[1]: Finished Apply Kernel Variables.
[ 3.461248] systemd-journald[122]: Collecting audit messages is disabled.
[ 3.464179] systemd[1]: Starting Create Static Device Nodes in /dev gracefully...
[ 3.504269] systemd[1]: Started Journal Service.
[ 5.438720] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
[ 5.500768] meson-vrtc ff8000a8.rtc: registered as rtc0
[ 5.500890] meson-vrtc ff8000a8.rtc: setting system clock to 2024-12-20T19:47:28 UTC (1734724048)
[ 5.501177] meson-gx-mmc ffe05000.mmc: Got CD GPIO
[ 5.501349] meson-gx-mmc ffe07000.mmc: allocated mmc-pwrseq
[ 5.509881] systemd-journald[122]: Time jumped backwards, rotating.
[ 5.710900] dwc3-meson-g12a ffe09000.usb: USB2 ports: 2
[ 5.710968] dwc3-meson-g12a ffe09000.usb: USB3 ports: 1
[ 5.794609] dwc2 ff400000.usb: supply vusb_d not found, using dummy regulator
[ 5.796384] dwc2 ff400000.usb: supply vusb_a not found, using dummy regulator
[ 5.803879] dwc2 ff400000.usb: EPs: 7, dedicated fifos, 712 entries in SPRAM
[ 5.822642] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 5.823025] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1
[ 5.830694] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228fe6c hci version 0x110 quirks 0x0000808000000010
[ 5.839651] xhci-hcd xhci-hcd.1.auto: irq 18, io mem 0xff500000
[ 5.845695] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 5.851264] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2
[ 5.858644] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 5.865313] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.12
[ 5.873259] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.880434] usb usb1: Product: xHCI Host Controller
[ 5.885282] usb usb1: Manufacturer: Linux 6.12.21-gentoo-dist xhci-hcd
[ 5.891782] usb usb1: SerialNumber: xhci-hcd.1.auto
[ 5.897484] hub 1-0:1.0: USB hub found
[ 5.900506] hub 1-0:1.0: 2 ports detected
[ 5.905121] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 5.912654] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.12
[ 5.920651] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.927854] usb usb2: Product: xHCI Host Controller
[ 5.932689] usb usb2: Manufacturer: Linux 6.12.21-gentoo-dist xhci-hcd
[ 5.939201] usb usb2: SerialNumber: xhci-hcd.1.auto
[ 5.944874] hub 2-0:1.0: USB hub found
[ 5.947866] hub 2-0:1.0: 1 port detected
[ 6.163462] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 6.295962] usb 1-1: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice= 6.63
[ 6.298552] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 6.305660] usb 1-1: Product: USB2.1 Hub
[ 6.309554] usb 1-1: Manufacturer: GenesysLogic
[ 6.377465] hub 1-1:1.0: USB hub found
[ 6.377845] hub 1-1:1.0: 4 ports detected
[ 6.399406] usbcore: registered new device driver onboard-usb-dev
[ 6.410376] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 6.430799] usb 2-1: New USB device found, idVendor=05e3, idProduct=0626, bcdDevice= 6.63
[ 6.433375] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 6.440516] usb 2-1: Product: USB3.1 Hub
[ 6.444392] usb 2-1: Manufacturer: GenesysLogic
[ 6.474265] hub 2-1:1.0: USB hub found
[ 6.475144] hub 2-1:1.0: 4 ports detected
[ 6.676796] usb 1-1.4: new full-speed USB device number 3 using xhci-hcd
[ 6.795317] usb 1-1.4: New USB device found, idVendor=062a, idProduct=4c01, bcdDevice= 1.25
[ 6.798082] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 6.805356] usb 1-1.4: Product: 2.4G INPUT DEVICE
[ 6.810033] usb 1-1.4: Manufacturer: MOSART Semi.
[ 6.889689] usb 2-1.2: new SuperSpeed USB device number 3 using xhci-hcd
[ 6.891231] input: MOSART Semi. 2.4G INPUT DEVICE as /devices/platform/soc/ffe09000.usb/ff500000.usb/xhci-hcd.1.auto/usb1/1-1/1-1.4/1-1.4:1.0/0003:062A:4C01.0001/input/input1
[ 6.911477] usb 2-1.2: New USB device found, idVendor=05e3, idProduct=0749, bcdDevice=15.39
[ 6.914644] usb 2-1.2: New USB device strings: Mfr=3, Product=4, SerialNumber=5
[ 6.921914] usb 2-1.2: Product: USB3.0 Card Reader
[ 6.926675] usb 2-1.2: Manufacturer: Generic
[ 6.930922] usb 2-1.2: SerialNumber: 000000001539
[ 6.954486] usb-storage 2-1.2:1.0: USB Mass Storage device detected
[ 6.955878] scsi host0: usb-storage 2-1.2:1.0
[ 6.960015] usbcore: registered new interface driver usb-storage
[ 6.970471] usbcore: registered new interface driver uas
[ 7.020602] hid-generic 0003:062A:4C01.0001: input,hidraw0: USB HID v1.10 Keyboard [MOSART Semi. 2.4G INPUT DEVICE] on usb-xhci-hcd.1.auto-1.4/input0
[ 7.031572] input: MOSART Semi. 2.4G INPUT DEVICE Mouse as /devices/platform/soc/ffe09000.usb/ff500000.usb/xhci-hcd.1.auto/usb1/1-1/1-1.4/1-1.4:1.1/0003:062A:4C01.0002/input/input2
[ 7.045049] input: MOSART Semi. 2.4G INPUT DEVICE Consumer Control as /devices/platform/soc/ffe09000.usb/ff500000.usb/xhci-hcd.1.auto/usb1/1-1/1-1.4/1-1.4:1.1/0003:062A:4C01.0002/input/input3
[ 7.113776] input: MOSART Semi. 2.4G INPUT DEVICE System Control as /devices/platform/soc/ffe09000.usb/ff500000.usb/xhci-hcd.1.auto/usb1/1-1/1-1.4/1-1.4:1.1/0003:062A:4C01.0002/input/input4
[ 7.125373] input: MOSART Semi. 2.4G INPUT DEVICE as /devices/platform/soc/ffe09000.usb/ff500000.usb/xhci-hcd.1.auto/usb1/1-1/1-1.4/1-1.4:1.1/0003:062A:4C01.0002/input/input5
[ 7.141355] hid-generic 0003:062A:4C01.0002: input,hiddev96,hidraw1: USB HID v1.10 Mouse [MOSART Semi. 2.4G INPUT DEVICE] on usb-xhci-hcd.1.auto-1.4/input1
[ 7.975729] scsi 0:0:0:0: Direct-Access Generic MassStorageClass 1539 PQ: 0 ANSI: 6
[ 7.979773] scsi 0:0:0:1: Direct-Access Generic MassStorageClass 1539 PQ: 0 ANSI: 6
[ 7.987844] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 7.992305] sd 0:0:0:0: [sda] Media removed, stopped polling
[ 7.998622] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 8.000668] sd 0:0:0:1: Attached scsi generic sg1 type 0
[ 8.471109] sd 0:0:0:1: [sdb] 499744768 512-byte logical blocks: (256 GB/238 GiB)
[ 8.473939] sd 0:0:0:1: [sdb] Write Protect is off
[ 8.477798] sd 0:0:0:1: [sdb] Mode Sense: 21 00 00 00
[ 8.478735] sd 0:0:0:1: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 8.557163] sdb: sdb1 sdb2 sdb3 sdb4
[ 8.558131] sd 0:0:0:1: [sdb] Attached SCSI removable disk
[ 9.819898] XFS (sdb3): Mounting V5 Filesystem a39c0ab6-c7fb-4958-b691-178604eaa03d
[ 10.010109] XFS (sdb3): Ending clean mount
[ 11.031746] systemd-journald[122]: Received SIGTERM from PID 1 (systemd).
[ 11.493602] systemd[1]: systemd 256.10 running in system mode (+PAM -AUDIT -SELINUX -APPARMOR +IMA +SMACK +SECCOMP +GCRYPT -GNUTLS +OPENSSL +ACL +BLKID -CURL -ELFUTILS -FIDO2 +IDN2 -IDN -IPTC +KMOD -LIBCRYPTSETUP -LIBCRYPTSETUP_PLUGINS +LIBFDISK +PCRE2 -PWQUALITY -P11KIT -QRENCODE -TPM2 -BZIP2 +LZ4 -XZ -ZLIB +ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP -SYSVINIT -LIBARCHIVE)
[ 11.520647] systemd[1]: Detected architecture arm64.
[ 13.305155] systemd[1]: run-credentials-systemd\x2djournald.service.mount: Deactivated successfully.
[ 13.314021] systemd[1]: initrd-switch-root.service: Deactivated successfully.
[ 13.316682] systemd[1]: Stopped Switch Root.
[ 13.336863] systemd[1]: systemd-journald.service: Scheduled restart job, restart counter is at 1.
[ 13.343371] systemd[1]: Created slice Slice /system/getty.
[ 13.365782] systemd[1]: Created slice Slice /system/serial-getty.
[ 13.385250] systemd[1]: Created slice User and Session Slice.
[ 13.403952] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 13.423871] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 13.444402] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 13.466980] systemd[1]: Expecting device /dev/disk/by-diskseq/2-part2...
[ 13.483538] systemd[1]: Expecting device /dev/disk/by-uuid/82eca2bd-5d31-4757-a589-85c920b3ec1e...
[ 13.503540] systemd[1]: Expecting device /dev/disk/by-uuid/8E33-D949...
[ 13.520224] systemd[1]: Expecting device /dev/ttyAML0...
[ 13.533648] systemd[1]: Stopped target Switch Root.
[ 13.546963] systemd[1]: Stopped target Initrd File Systems.
[ 13.563589] systemd[1]: Stopped target Initrd Root File System.
[ 13.580418] systemd[1]: Reached target Path Units.
[ 13.593625] systemd[1]: Reached target Remote File Systems.
[ 13.610280] systemd[1]: Reached target Slice Units.
[ 13.623678] systemd[1]: Reached target System Time Set.
[ 13.643996] systemd[1]: Listening on Process Core Dump Socket.
[ 13.664927] systemd[1]: Listening on Credential Encryption/Decryption.
[ 13.684669] systemd[1]: Listening on Journal Audit Socket.
[ 13.700703] systemd[1]: Listening on DDI File System Mounter Socket.
[ 13.717590] systemd[1]: Listening on Network Service Netlink Socket.
[ 13.737351] systemd[1]: Listening on Namespace Resource Manager Socket.
[ 13.757470] systemd[1]: Listening on udev Control Socket.
[ 13.770649] systemd[1]: Listening on udev Kernel Socket.
[ 13.784032] systemd[1]: Listening on User Database Manager Socket.
[ 13.805862] systemd[1]: Mounting Huge Pages File System...
[ 13.824582] systemd[1]: Mounting POSIX Message Queue File System...
[ 13.880151] systemd[1]: Mounting Kernel Debug File System...
[ 13.897807] systemd[1]: Mounting Kernel Trace File System...
[ 13.918644] systemd[1]: Starting Create List of Static Device Nodes...
[ 13.945001] systemd[1]: Starting Load Kernel Module configfs...
[ 13.968342] systemd[1]: Starting Load Kernel Module dm_mod...
[ 13.991697] systemd[1]: Starting Load Kernel Module drm...
[ 14.011657] systemd[1]: Starting Load Kernel Module efi_pstore...
[ 14.035008] systemd[1]: Starting Load Kernel Module fuse...
[ 14.054991] systemd[1]: Starting Load Kernel Module loop...
[ 14.070504] systemd[1]: systemd-fsck-root.service: Deactivated successfully.
[ 14.072305] systemd[1]: Stopped File System Check on Root Device.
[ 14.084372] fuse: init (API version 7.41)
[ 14.107428] systemd[1]: Clear Stale Hibernate Storage Info was skipped because of an unmet condition check (ConditionPathExists=/sys/firmware/efi/efivars/HibernateLocation-8cf2644b-4b0b-428f-9387-6d876050dc67).
[ 14.130891] loop: module loaded
[ 14.131059] systemd[1]: Starting Journal Service...
[ 14.150132] systemd[1]: Load Kernel Modules was skipped because no trigger condition checks were met.
[ 14.158212] systemd[1]: Starting Generate network units from Kernel command line...
[ 14.207242] systemd[1]: Starting Remount Root and Kernel File Systems...
[ 14.231866] systemd[1]: Starting Apply Kernel Variables...
[ 14.256585] systemd[1]: Starting Load udev Rules from Credentials...
[ 14.290268] systemd-journald[383]: Collecting audit messages is enabled.
[ 14.294697] systemd[1]: Starting Coldplug All udev Devices...
[ 14.323861] systemd[1]: Started Journal Service.
[ 16.072300] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 16.075263] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 16.080934] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600'
[ 16.087415] Loading firmware: regulatory.db
[ 16.091689] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 16.103557] cfg80211: failed to load regulatory.db
[ 16.856081] meson-pwm ff802000.pwm: using obsolete compatible, please consider updating dt
[ 16.878121] debugfs: Directory 'ff800280.cec' with parent 'regmap' already present!
[ 16.880889] Registered IR keymap rc-cec
[ 16.884672] rc rc0: meson_g12a_ao_cec as /devices/platform/soc/ff800000.bus/ff800280.cec/rc/rc0
[ 16.892978] input: meson_g12a_ao_cec as /devices/platform/soc/ff800000.bus/ff800280.cec/rc/rc0/input6
[ 16.898528] Registered IR keymap rc-empty
[ 16.907014] rc rc1: meson-ir as /devices/platform/soc/ff800000.bus/ff808000.ir/rc/rc1
[ 16.915753] rc rc1: lirc_dev: driver meson-ir registered at minor = 0, raw IR receiver, no transmitter
[ 16.928149] input: meson-ir as /devices/platform/soc/ff800000.bus/ff808000.ir/rc/rc1/input7
[ 16.932229] rc rc1: sw decoder init
[ 16.936606] meson-ir ff808000.ir: receiver initialized
[ 16.984588] mc: Linux media interface: v0.10
[ 17.010927] etnaviv etnaviv: bound ff100000.npu (ops __this_module [etnaviv])
[ 17.012574] etnaviv-gpu ff100000.npu: model: GC8000, revision: 7131
[ 17.021736] [drm] Initialized etnaviv 1.4.0 for etnaviv on minor 0
[ 17.076896] videodev: Linux video capture interface: v2.00
[ 17.145134] meson8b-dwmac ff3f0000.ethernet: IRQ eth_wake_irq not found
[ 17.146155] meson8b-dwmac ff3f0000.ethernet: IRQ eth_lpi not found
[ 17.152360] meson8b-dwmac ff3f0000.ethernet: IRQ sfty not found
[ 17.158392] meson8b-dwmac ff3f0000.ethernet: PTP uses main clock
[ 17.165243] meson8b-dwmac ff3f0000.ethernet: User ID: 0x11, Synopsys ID: 0x37
[ 17.171336] meson8b-dwmac ff3f0000.ethernet: DWMAC1000
[ 17.176545] meson8b-dwmac ff3f0000.ethernet: DMA HW capability register supported
[ 17.183978] meson8b-dwmac ff3f0000.ethernet: RX Checksum Offload Engine supported
[ 17.191435] meson8b-dwmac ff3f0000.ethernet: COE Type 2
[ 17.196673] meson8b-dwmac ff3f0000.ethernet: TX Checksum insertion supported
[ 17.203635] meson8b-dwmac ff3f0000.ethernet: Wake-Up On Lan supported
[ 17.210187] meson8b-dwmac ff3f0000.ethernet: Normal descriptors
[ 17.215956] meson8b-dwmac ff3f0000.ethernet: Ring mode enabled
[ 17.221764] meson8b-dwmac ff3f0000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 17.445780] meson_vdec: module is from the staging directory, the quality is unknown, you have been warned.
[ 17.484949] panfrost ffe40000.gpu: clock rate = 24000000
[ 17.485081] panfrost ffe40000.gpu: error -ENODEV: _opp_set_regulators: no regulator (mali) found
[ 17.500522] panfrost ffe40000.gpu: mali-g31 id 0x7093 major 0x0 minor 0x0 status 0x0
[ 17.502661] panfrost ffe40000.gpu: features: 00000000,000027f7, issues: 00000000,00000400
[ 17.510929] panfrost ffe40000.gpu: Features: L2:0x07100206 Shader:0x00000000 Tiler:0x00000209 Mem:0x1 MMU:0x00002821 AS:0xff JS:0x7
[ 17.522651] panfrost ffe40000.gpu: shader_present=0x1 l2_present=0x1
[ 17.539807] [drm] Initialized panfrost 1.2.0 for ffe40000.gpu on minor 1
[ 17.546193] meson8b-dwmac ff3f0000.ethernet end0: renamed from eth0
[ 17.611955] meson8b-dwmac ff3f0000.ethernet end0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 17.697002] meson8b-dwmac ff3f0000.ethernet end0: PHY [mdio_mux-0.0:00] driver [RTL8211F Gigabit Ethernet] (irq=32)
[ 17.716499] XFS (sdb4): Mounting V5 Filesystem 82eca2bd-5d31-4757-a589-85c920b3ec1e
[ 17.717183] meson8b-dwmac ff3f0000.ethernet end0: No Safety Features support found
[ 17.726240] meson8b-dwmac ff3f0000.ethernet end0: PTP not supported by HW
[ 17.734636] meson8b-dwmac ff3f0000.ethernet end0: configuring for phy/rgmii link mode
[ 17.751870] Adding 8388604k swap on /dev/sdb2. Priority:-2 extents:1 across:8388604k
[ 17.753900] FAT-fs (sdb1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 17.891423] XFS (sdb4): Ending clean mount
[ 18.080375] systemd-journald[383]: Received client request to flush runtime journal.
[ 18.150614] systemd-journald[383]: /var/log/journal/ee94f8fd6442413cb0625f3b7f2d814b/system.journal: Realtime clock jumped backwards relative to last journal entry, rotating.
[ 18.160739] systemd-journald[383]: Rotating system journal.
[ 18.251031] systemd-journald[383]: /var/log/journal/ee94f8fd6442413cb0625f3b7f2d814b/system.journal: Realtime clock jumped backwards relative to last journal entry, rotating.
[ 18.261144] systemd-journald[383]: Rotating system journal.
[ 20.807877] meson8b-dwmac ff3f0000.ethernet end0: Link is Up - 1Gbps/Full - flow control off
[ 27.791596] platform sound: deferred probe pending: axg-sound-card: can't parse dai
[ 37.321116] systemd-journald[383]: /var/log/journal/ee94f8fd6442413cb0625f3b7f2d814b/user-1000.journal: Realtime clock jumped backwards relative to last journal entry, rotating. |
|
|
| Back to top |
|
|
pingtoo
Veteran
Joined: 10 Sep 2021
Posts: 1684
Location: Richmond Hill, Canada
|
| Posted: Sun Apr 20, 2025 10:57 am Post subject: |
|
|
So after you USB boot success. Can you access the internal SD card? may be place some sample SD card into the internal reader and test access.
It could be just timing issue, may be mmc1 is not ready by the time initrd wants to access? you can try to use kernel command line "break=pre-trigger" to break into dracut shell and examine if you have right driver load into your initrd. |
|
| Back to top |
|
|
JumboAg
Apprentice
Joined: 03 Mar 2007
Posts: 220
Location: Dallas, TX
|
| Posted: Sun Apr 20, 2025 5:45 pm Post subject: |
|
|
yes I can access it fine after booting. I can even move the root SD card from the emmc to the external while the system is still retrying the dracut-initqueue stuff and it'll immediately finish booting.
I've gone as far as to add every single module/driver showing up in a lsmod into the initramfs. Still no luck. |
|
| Back to top |
|
|
NeddySeagoon
Administrator
Joined: 05 Jul 2003
Posts: 55437
Location: 56N 3W
|
| Posted: Sun Apr 20, 2025 7:17 pm Post subject: |
|
|
JumboAg,
I suspect its the asynchronous nature of the kernel detecting mmc devices.
The initrd needs ta wait for it before trying to use it.
That will be a feature of the init script in the initrd.
_________________
Regards,
NeddySeagoon
Computer users fall into two groups:-
those that do backups
those that have never had a hard drive fail. |
|
| Back to top |
|
|
pingtoo
Veteran
Joined: 10 Sep 2021
Posts: 1684
Location: Richmond Hill, Canada
|
| Posted: Sun Apr 20, 2025 8:19 pm Post subject: |
|
|
| JumboAg wrote: | yes I can access it fine after booting. I can even move the root SD card from the emmc to the external while the system is still retrying the dracut-initqueue stuff and it'll immediately finish booting.
I've gone as far as to add every single module/driver showing up in a lsmod into the initramfs. Still no luck. |
In this case it will helpful to see what you see inside initrd for example at dracut-initqueue stage. things like lsmod and dmesg. I think modern busybox have lsusb also. lsblk too. may be something is there just not the name your are expecting. |
|
| Back to top |
|
|
zen_desu
Guru
Joined: 25 Oct 2024
Posts: 321
|
| Posted: Sun Apr 20, 2025 8:24 pm Post subject: |
|
|
| JumboAg wrote: | yes I can access it fine after booting. I can even move the root SD card from the emmc to the external while the system is still retrying the dracut-initqueue stuff and it'll immediately finish booting.
I've gone as far as to add every single module/driver showing up in a lsmod into the initramfs. Still no luck. |
Have you also confirmed they were loaded in the initramfs recovery shell?
_________________
µgRD dev
Wiki writer |
|
| Back to top |
|
|
JumboAg
Apprentice
Joined: 03 Mar 2007
Posts: 220
Location: Dallas, TX
|
| Posted: Wed Apr 23, 2025 1:35 am Post subject: |
|
|
| zen_desu wrote: | | JumboAg wrote: | yes I can access it fine after booting. I can even move the root SD card from the emmc to the external while the system is still retrying the dracut-initqueue stuff and it'll immediately finish booting.
I've gone as far as to add every single module/driver showing up in a lsmod into the initramfs. Still no luck. |
Have you also confirmed they were loaded in the initramfs recovery shell? |
I have. |
|
| Back to top |
|
|
NeddySeagoon
Administrator
Joined: 05 Jul 2003
Posts: 55437
Location: 56N 3W
|
| Posted: Wed Apr 23, 2025 9:20 am Post subject: |
|
|
JumboAg,
Can you unpick your initrd and pastebin the init script please?
_________________
Regards,
NeddySeagoon
Computer users fall into two groups:-
those that do backups
those that have never had a hard drive fail. |
|
| Back to top |
|
|
JumboAg
Apprentice
Joined: 03 Mar 2007
Posts: 220
Location: Dallas, TX
|
| Posted: Wed Apr 23, 2025 11:10 pm Post subject: |
|
|
Not quite sure what you're wanting. The "init" script in the image is a symlink to a systemd binary.
| Code: | $ ls
bin etc lib roc run shutdown sysroot usr
dev init lib64 root sbin sys tmp var
me@solitudepi /tmp/initrd $ file init
init: symbolic link to usr/lib/systemd/systemd
me@solitudepi /tmp/initrd $ file usr/lib/systemd/systemd
usr/lib/systemd/systemd: ELF 64-bit LSB pie executable, ARM aarch64, version 1 (SYSV), dynamically linked, interpreter /lib/ld-linux-aarch64.so.1, for GNU/Linux 3.7.0, stripped |
I'm sure I'm misunderstanding your ask. |
|
| Back to top |
|
|
NeddySeagoon
Administrator
Joined: 05 Jul 2003
Posts: 55437
Location: 56N 3W
|
| Posted: Thu Apr 24, 2025 9:45 am Post subject: |
|
|
JumboAg,
I was expecting busybox and a human readable script that runs in the busybox shell.
For root on mmc and other asynchronouly detected media, the init script must check that the media is available before it attempts to mount any filesysems there.
Without that check, mounting root fails.
Then you get dropped to the rescue shell. When you look at /dev for your mmc, all is well, as that is time enough for it to appear.
I don't know how systemd does that mmc check, or if it does it at all.
_________________
Regards,
NeddySeagoon
Computer users fall into two groups:-
those that do backups
those that have never had a hard drive fail. |
|
| Back to top |
|
|
JumboAg
Apprentice
Joined: 03 Mar 2007
Posts: 220
Location: Dallas, TX
|
| Posted: Thu Apr 24, 2025 11:17 am Post subject: |
|
|
| Give me a few days to build a new micro sd card using openrc. Assuming I have the same issue, I'll post the requested data. I can move back to systemd once we figure out the root cause. |
|
| Back to top |
|
|
Hu
Administrator
Joined: 06 Mar 2007
Posts: 23659
|
| Posted: Thu Apr 24, 2025 2:21 pm Post subject: |
|
|
| There is no need to have a full openrc card. It would suffice to have a simple shell script that busybox interprets, where that script ends the successful case by mounting root and transferring control to systemd. |
|
| Back to top |
|
|
JumboAg
Apprentice
Joined: 03 Mar 2007
Posts: 220
Location: Dallas, TX
|
| Posted: Thu Apr 24, 2025 10:25 pm Post subject: |
|
|
Got it. I was missing a driver in the initramfs. Didnt catch it because the driver only loads once a sd card is inserted into the mmc slot. When I was doing an lsmod after booting off USB, I found several *mmc* drivers and was loading them but mmc_block was not on my RADAR. It was also in the mmc/core directory and I was loading everything in the mmc/host directory.
The good news is I can mark this as yet one more SBC I've managed to load gentoo on.
Thank you to everyone that assisted me with resolving this.
| Code: | me@solitudepi ~ $ cat /etc/dracut.conf.d/meson-gx-mmc.conf
add_drivers+=" mmc_block meson_gx_mmc pwrseq_mmc mmc_core "
me@solitudepi ~ $ lsmod|grep mmc
mmc_block 53248 4
rpmb_core 16384 1 mmc_block
meson_gx_mmc 24576 0
pwrseq_emmc 12288 1
mmc_core 208896 3 mmc_block,pwrseq_emmc,meson_gx_mmc
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Gentoo on ARM
