Intel 945GM: How to make X use the native resolution?

Message

dlaor · Post by **dlaor** » Sun Jan 27, 2008 7:30 pm

A week ago I installed Gentoo linux for the first time. Setting it up is a slow process, but now I have my sata drive recognised and my internet connection working. This weekend I have installed X.org. This went fine but now I seem to be unable to make use of the native resolution (1600x1200) of my monitor, an HP LP2065 which is connected via DVI to the onboard Intel 945GM graphics chipset. So far I cannot get X to use anything else than the initial mode 1024x768.

I have tried the following:

- Changed /etc/X11/xorg.conf as described in the Intel GMA Wiki. This did not change anything.

- Changed from using vesafb to using uvesafb in my kernel, and changing /boot/grub/grub.conf accordingly. Now the console is in 1600x1200 (which is very nice), but still X starts in 1024x768...

I have read about the "915resolution" fix, but a lot of people call it ugly and a hack, so I did not try that. I also read that the newest intel drivers don't need this fix anymore, is this true?

Below are my xorg.conf and Xorg.0.log. I guess the problem will be the "bad mode clock/interlace/doublescan" errors or the "I830 Vblank Pipe Setup Failed 0" error, does anyone know how to fix these?

Thanks in advance, dlaor.

Code: Select all

Section "ServerLayout"
	Identifier     "X.org Configured"
	Screen      0  "Screen0" 0 0
	InputDevice    "Mouse0" "CorePointer"
	InputDevice    "Keyboard0" "CoreKeyboard"
EndSection

Section "Files"
	RgbPath      "/usr/share/X11/rgb"
	ModulePath   "/usr/lib64/xorg/modules"
	FontPath     "/usr/share/fonts/misc/"
	FontPath     "/usr/share/fonts/TTF/"
	FontPath     "/usr/share/fonts/OTF"
	FontPath     "/usr/share/fonts/Type1/"
	FontPath     "/usr/share/fonts/100dpi/"
	FontPath     "/usr/share/fonts/75dpi/"
EndSection

Section "Module"
	Load  "extmod"
	Load  "xtrap"
	Load  "dri"
	Load  "GLcore"
	Load  "record"
	Load  "glx"
	Load  "dbe"
	Load  "freetype"
	Load  "type1"
EndSection

Section "InputDevice"
	Identifier  "Keyboard0"
	Driver      "kbd"
EndSection

Section "InputDevice"
	Identifier  "Mouse0"
	Driver      "mouse"
	Option	    "Protocol" "auto"
	Option	    "Device" "/dev/input/mice"
	Option	    "ZAxisMapping" "4 5 6 7"
EndSection

Section "Monitor"
	#DisplaySize	  410   310	# mm
	Identifier   "Monitor0"
	VendorName   "HWP"
	ModelName    "HP LP2065"
 ### Comment all HorizSync and VertRefresh values to use DDC:
	HorizSync    30.0 - 92.0
	VertRefresh  48.0 - 85.0
	Option	    "DPMS"
	Modeline	"1600x1200_60.0" 160.96 1600 1704 1880 2160 1200 1201 1204 1242 -HSync +VSync
EndSection

Section "Device"
        ### Available Driver options are:-
        ### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
        ### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
        ### [arg]: arg optional
        #Option     "NoAccel"            	# [<bool>]
        #Option     "SWcursor"           	# [<bool>]
        #Option     "ColorKey"           	# <i>
        #Option     "CacheLines"         	# <i>
        #Option     "Dac6Bit"            	# [<bool>]
        #Option     "DRI"                	# [<bool>]
        #Option     "NoDDC"              	# [<bool>]
        #Option     "ShowCache"          	# [<bool>]
        #Option     "XvMCSurfaces"       	# <i>
        #Option     "PageFlip"           	# [<bool>]
	Identifier  "Card0"
	Driver      "intel"
	VendorName  "Intel Corporation"
	BoardName   "Mobile 945GM/GMS/940GML Express Integrated Graphics Controller"
	BusID       "PCI:0:2:0"
	Option		"Monitor-TMDS-1" "Monitor0"
EndSection

Section "Screen"
	Identifier "Screen0"
	Device     "Card0"
	Monitor    "Monitor0"
	DefaultDepth 24
	SubSection "Display"
		Viewport   0 0
		Depth     1
		Modes	"1600x1200"
	EndSubSection
	SubSection "Display"
		Viewport   0 0
		Depth     4
		Modes	"1600x1200"
	EndSubSection
	SubSection "Display"
		Viewport   0 0
		Depth     8
		Modes	"1600x1200"
	EndSubSection
	SubSection "Display"
		Viewport   0 0
		Depth     15
		Modes	"1600x1200"
	EndSubSection
	SubSection "Display"
		Viewport   0 0
		Depth     16
		Modes	"1600x1200"
	EndSubSection
	SubSection "Display"
		Viewport   0 0
		Depth     24
		Modes	"1600x1200"
	EndSubSection
EndSection

Section "DRI"
  Mode 0666
EndSection

Code: Select all

[/url]
X Window System Version 1.3.0
Release Date: 19 April 2007
X Protocol Version 11, Revision 0, Release 1.3
Build Operating System: UNKNOWN 
Current Operating System: Linux dlaor 2.6.23-gentoo-r6 #5 SMP Sun Jan 27 18:03:23 GMT 2008 x86_64
Build Date: 27 January 2008
	Before reporting problems, check http://wiki.x.org
	to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
	(++) from command line, (!!) notice, (II) informational,
	(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Sun Jan 27 18:28:58 2008
(==) Using config file: "/etc/X11/xorg.conf"
(==) ServerLayout "X.org Configured"
(**) |-->Screen "Screen0" (0)
(**) |   |-->Monitor "Monitor0"
(**) |   |-->Device "Card0"
(**) |-->Input Device "Mouse0"
(**) |-->Input Device "Keyboard0"
(WW) The directory "/usr/share/fonts/TTF/" does not exist.
	Entry deleted from font path.
(WW) The directory "/usr/share/fonts/OTF" does not exist.
	Entry deleted from font path.
(**) FontPath set to:
	/usr/share/fonts/misc/,
	/usr/share/fonts/Type1/,
	/usr/share/fonts/100dpi/,
	/usr/share/fonts/75dpi/
(**) RgbPath set to "/usr/share/X11/rgb"
(**) ModulePath set to "/usr/lib64/xorg/modules"
(WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
(II) No APM support in BIOS or kernel
(II) Loader magic: 0x6ac420
(II) Module ABI versions:
	X.Org ANSI C Emulation: 0.3
	X.Org Video Driver: 1.2
	X.Org XInput driver : 0.7
	X.Org Server Extension : 0.3
	X.Org Font Renderer : 0.5
(II) Loader running on linux
(II) LoadModule: "pcidata"
(II) Loading /usr/lib64/xorg/modules//libpcidata.so
(II) Module pcidata: vendor="X.Org Foundation"
	compiled for 1.3.0, module version = 1.0.0
	ABI class: X.Org Video Driver, version 1.2
(--) using VT number 7

(II) PCI: PCI scan (all values are in hex)
(II) PCI: 00:00:0: chip 8086,27a0 card 8086,27a0 rev 03 class 06,00,00 hdr 00
(II) PCI: 00:02:0: chip 8086,27a2 card 8086,27a2 rev 03 class 03,00,00 hdr 80
(II) PCI: 00:02:1: chip 8086,27a6 card 8086,27a2 rev 03 class 03,80,00 hdr 80
(II) PCI: 00:1b:0: chip 8086,27d8 card 16f3,806e rev 02 class 04,03,00 hdr 00
(II) PCI: 00:1c:0: chip 8086,27d0 card 0000,0000 rev 02 class 06,04,00 hdr 81
(II) PCI: 00:1c:1: chip 8086,27d2 card 0000,0000 rev 02 class 06,04,00 hdr 81
(II) PCI: 00:1d:0: chip 8086,27c8 card 8086,27c8 rev 02 class 0c,03,00 hdr 80
(II) PCI: 00:1d:1: chip 8086,27c9 card 8086,27c9 rev 02 class 0c,03,00 hdr 00
(II) PCI: 00:1d:2: chip 8086,27ca card 8086,27ca rev 02 class 0c,03,00 hdr 00
(II) PCI: 00:1d:3: chip 8086,27cb card 8086,27cb rev 02 class 0c,03,00 hdr 00
(II) PCI: 00:1d:7: chip 8086,27cc card 8086,27cc rev 02 class 0c,03,20 hdr 00
(II) PCI: 00:1e:0: chip 8086,2448 card 0000,0000 rev e2 class 06,04,01 hdr 01
(II) PCI: 00:1f:0: chip 8086,27b9 card 8086,27b9 rev 02 class 06,01,00 hdr 80
(II) PCI: 00:1f:2: chip 8086,27c4 card 8086,27c4 rev 02 class 01,01,80 hdr 00
(II) PCI: 00:1f:3: chip 8086,27da card 8086,27da rev 02 class 0c,05,00 hdr 00
(II) PCI: 01:00:0: chip 10ec,8168 card 10ec,8168 rev 01 class 02,00,00 hdr 00
(II) PCI: 02:00:0: chip 10ec,8168 card 10ec,8168 rev 01 class 02,00,00 hdr 00
(II) PCI: 03:06:0: chip 1102,0004 card 1102,4002 rev 03 class 04,01,00 hdr 00
(II) PCI: 03:09:0: chip 1106,3044 card 1106,3044 rev 80 class 0c,00,10 hdr 00
(II) PCI: End of PCI scan
(II) Intel Bridge workaround enabled
(II) Host-to-PCI bridge:
(II) Bus 0: bridge is at (0:0:0), (0,0,3), BCTRL: 0x0008 (VGA_EN is set)
(II) Bus 0 I/O range:
	[0] -1	0	0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) Bus 0 non-prefetchable memory range:
	[0] -1	0	0x00000000 - 0xffffffff (0x100000000) MX[B]
(II) Bus 0 prefetchable memory range:
	[0] -1	0	0x00000000 - 0xffffffff (0x100000000) MX[B]
(II) PCI-to-PCI bridge:
(II) Bus 1: bridge is at (0:28:0), (0,1,1), BCTRL: 0x0000 (VGA_EN is cleared)
(II) Bus 1 I/O range:
	[0] -1	0	0x0000c000 - 0x0000cfff (0x1000) IX[B]
(II) Bus 1 non-prefetchable memory range:
	[0] -1	0	0xfdb00000 - 0xfdbfffff (0x100000) MX[B]
(II) Bus 1 prefetchable memory range:
	[0] -1	0	0xfd800000 - 0xfd8fffff (0x100000) MX[B]
(II) PCI-to-PCI bridge:
(II) Bus 2: bridge is at (0:28:1), (0,2,2), BCTRL: 0x0000 (VGA_EN is cleared)
(II) Bus 2 I/O range:
	[0] -1	0	0x0000e000 - 0x0000efff (0x1000) IX[B]
(II) Bus 2 non-prefetchable memory range:
	[0] -1	0	0xfdd00000 - 0xfddfffff (0x100000) MX[B]
(II) Bus 2 prefetchable memory range:
	[0] -1	0	0xfdc00000 - 0xfdcfffff (0x100000) MX[B]
(II) Subtractive PCI-to-PCI bridge:
(II) Bus 3: bridge is at (0:30:0), (0,3,3), BCTRL: 0x0000 (VGA_EN is cleared)
(II) Bus 3 I/O range:
	[0] -1	0	0x0000d000 - 0x0000dfff (0x1000) IX[B]
(II) Bus 3 non-prefetchable memory range:
	[0] -1	0	0xfda00000 - 0xfdafffff (0x100000) MX[B]
(II) Bus 3 prefetchable memory range:
	[0] -1	0	0xfd900000 - 0xfd9fffff (0x100000) MX[B]
(II) PCI-to-ISA bridge:
(II) Bus -1: bridge is at (0:31:0), (0,-1,-1), BCTRL: 0x0008 (VGA_EN is set)
(--) PCI:*(0:2:0) Intel Corporation Mobile 945GM/GMS/940GML Express Integrated Graphics Controller rev 3, Mem @ 0xfde80000/19, 0xd0000000/28, 0xfdf80000/18, I/O @ 0xff00/3
(--) PCI: (0:2:1) Intel Corporation Mobile 945GM/GMS/940GML Express Integrated Graphics Controller rev 3, Mem @ 0xfdf00000/19
(II) Addressable bus resource ranges are
	[0] -1	0	0x00000000 - 0xffffffff (0x100000000) MX[B]
	[1] -1	0	0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) OS-reported resource ranges:
	[0] -1	0	0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
	[1] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[2] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[3] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[4] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[5] -1	0	0x00000000 - 0x000000ff (0x100) IX[B]
(II) Active PCI resource ranges:
	[0] -1	0	0xfdaff000 - 0xfdaff7ff (0x800) MX[B]
	[1] -1	0	0xfddff000 - 0xfddfffff (0x1000) MX[B]
	[2] -1	0	0xfdbff000 - 0xfdbfffff (0x1000) MX[B]
	[3] -1	0	0xfdfff000 - 0xfdfff3ff (0x400) MX[B]
	[4] -1	0	0xfdff8000 - 0xfdffbfff (0x4000) MX[B]
	[5] -1	0	0xfdf00000 - 0xfdf7ffff (0x80000) MX[B](B)
	[6] -1	0	0xfdf80000 - 0xfdfbffff (0x40000) MX[B](B)
	[7] -1	0	0xd0000000 - 0xdfffffff (0x10000000) MX[B](B)
	[8] -1	0	0xfde80000 - 0xfdefffff (0x80000) MX[B](B)
	[9] -1	0	0x0000de00 - 0x0000de7f (0x80) IX[B]
	[10] -1	0	0x0000df00 - 0x0000df1f (0x20) IX[B]
	[11] -1	0	0x0000ee00 - 0x0000eeff (0x100) IX[B]
	[12] -1	0	0x0000ce00 - 0x0000ceff (0x100) IX[B]
	[13] -1	0	0x00000500 - 0x0000051f (0x20) IX[B]
	[14] -1	0	0x0000fa00 - 0x0000fa0f (0x10) IX[B]
	[15] -1	0	0x000001f0 - 0x000001f0 (0x1) IX[B]
	[16] -1	0	0x000001f0 - 0x000001f7 (0x8) IX[B]
	[17] -1	0	0x000001f0 - 0x000001f0 (0x1) IX[B]
	[18] -1	0	0x000001f0 - 0x000001f7 (0x8) IX[B]
	[19] -1	0	0x0000fb00 - 0x0000fb1f (0x20) IX[B]
	[20] -1	0	0x0000fc00 - 0x0000fc1f (0x20) IX[B]
	[21] -1	0	0x0000fd00 - 0x0000fd1f (0x20) IX[B]
	[22] -1	0	0x0000fe00 - 0x0000fe1f (0x20) IX[B]
	[23] -1	0	0x0000ff00 - 0x0000ff07 (0x8) IX[B](B)
(II) Active PCI resource ranges after removing overlaps:
	[0] -1	0	0xfdaff000 - 0xfdaff7ff (0x800) MX[B]
	[1] -1	0	0xfddff000 - 0xfddfffff (0x1000) MX[B]
	[2] -1	0	0xfdbff000 - 0xfdbfffff (0x1000) MX[B]
	[3] -1	0	0xfdfff000 - 0xfdfff3ff (0x400) MX[B]
	[4] -1	0	0xfdff8000 - 0xfdffbfff (0x4000) MX[B]
	[5] -1	0	0xfdf00000 - 0xfdf7ffff (0x80000) MX[B](B)
	[6] -1	0	0xfdf80000 - 0xfdfbffff (0x40000) MX[B](B)
	[7] -1	0	0xd0000000 - 0xdfffffff (0x10000000) MX[B](B)
	[8] -1	0	0xfde80000 - 0xfdefffff (0x80000) MX[B](B)
	[9] -1	0	0x0000de00 - 0x0000de7f (0x80) IX[B]
	[10] -1	0	0x0000df00 - 0x0000df1f (0x20) IX[B]
	[11] -1	0	0x0000ee00 - 0x0000eeff (0x100) IX[B]
	[12] -1	0	0x0000ce00 - 0x0000ceff (0x100) IX[B]
	[13] -1	0	0x00000500 - 0x0000051f (0x20) IX[B]
	[14] -1	0	0x0000fa00 - 0x0000fa0f (0x10) IX[B]
	[15] -1	0	0x000001f0 - 0x000001f0 (0x1) IX[B]
	[16] -1	0	0x000001f0 - 0x000001f7 (0x8) IX[B]
	[17] -1	0	0x000001f0 - 0x000001f0 (0x1) IX[B]
	[18] -1	0	0x000001f0 - 0x000001f7 (0x8) IX[B]
	[19] -1	0	0x0000fb00 - 0x0000fb1f (0x20) IX[B]
	[20] -1	0	0x0000fc00 - 0x0000fc1f (0x20) IX[B]
	[21] -1	0	0x0000fd00 - 0x0000fd1f (0x20) IX[B]
	[22] -1	0	0x0000fe00 - 0x0000fe1f (0x20) IX[B]
	[23] -1	0	0x0000ff00 - 0x0000ff07 (0x8) IX[B](B)
(II) OS-reported resource ranges after removing overlaps with PCI:
	[0] -1	0	0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
	[1] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[2] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[3] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[4] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[5] -1	0	0x00000000 - 0x000000ff (0x100) IX[B]
(II) All system resource ranges:
	[0] -1	0	0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
	[1] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[2] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[3] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[4] -1	0	0xfdaff000 - 0xfdaff7ff (0x800) MX[B]
	[5] -1	0	0xfddff000 - 0xfddfffff (0x1000) MX[B]
	[6] -1	0	0xfdbff000 - 0xfdbfffff (0x1000) MX[B]
	[7] -1	0	0xfdfff000 - 0xfdfff3ff (0x400) MX[B]
	[8] -1	0	0xfdff8000 - 0xfdffbfff (0x4000) MX[B]
	[9] -1	0	0xfdf00000 - 0xfdf7ffff (0x80000) MX[B](B)
	[10] -1	0	0xfdf80000 - 0xfdfbffff (0x40000) MX[B](B)
	[11] -1	0	0xd0000000 - 0xdfffffff (0x10000000) MX[B](B)
	[12] -1	0	0xfde80000 - 0xfdefffff (0x80000) MX[B](B)
	[13] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[14] -1	0	0x00000000 - 0x000000ff (0x100) IX[B]
	[15] -1	0	0x0000de00 - 0x0000de7f (0x80) IX[B]
	[16] -1	0	0x0000df00 - 0x0000df1f (0x20) IX[B]
	[17] -1	0	0x0000ee00 - 0x0000eeff (0x100) IX[B]
	[18] -1	0	0x0000ce00 - 0x0000ceff (0x100) IX[B]
	[19] -1	0	0x00000500 - 0x0000051f (0x20) IX[B]
	[20] -1	0	0x0000fa00 - 0x0000fa0f (0x10) IX[B]
	[21] -1	0	0x000001f0 - 0x000001f0 (0x1) IX[B]
	[22] -1	0	0x000001f0 - 0x000001f7 (0x8) IX[B]
	[23] -1	0	0x000001f0 - 0x000001f0 (0x1) IX[B]
	[24] -1	0	0x000001f0 - 0x000001f7 (0x8) IX[B]
	[25] -1	0	0x0000fb00 - 0x0000fb1f (0x20) IX[B]
	[26] -1	0	0x0000fc00 - 0x0000fc1f (0x20) IX[B]
	[27] -1	0	0x0000fd00 - 0x0000fd1f (0x20) IX[B]
	[28] -1	0	0x0000fe00 - 0x0000fe1f (0x20) IX[B]
	[29] -1	0	0x0000ff00 - 0x0000ff07 (0x8) IX[B](B)
(II) LoadModule: "extmod"
(II) Loading /usr/lib64/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
	compiled for 1.3.0, module version = 1.0.0
	Module class: X.Org Server Extension
	ABI class: X.Org Server Extension, version 0.3
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "xtrap"
(II) Loading /usr/lib64/xorg/modules/extensions//libxtrap.so
(II) Module xtrap: vendor="X.Org Foundation"
	compiled for 1.3.0, module version = 1.0.0
	Module class: X.Org Server Extension
	ABI class: X.Org Server Extension, version 0.3
(II) Loading extension DEC-XTRAP
(II) LoadModule: "dri"
(II) Loading /usr/lib64/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
	compiled for 1.3.0, module version = 1.0.0
	ABI class: X.Org Server Extension, version 0.3
(II) Loading extension XFree86-DRI
(II) LoadModule: "record"
(II) Loading /usr/lib64/xorg/modules/extensions//librecord.so
(II) Module record: vendor="X.Org Foundation"
	compiled for 1.3.0, module version = 1.13.0
	Module class: X.Org Server Extension
	ABI class: X.Org Server Extension, version 0.3
(II) Loading extension RECORD
(II) LoadModule: "glx"
(II) Loading /usr/lib64/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="X.Org Foundation"
	compiled for 1.3.0, module version = 1.0.0
	ABI class: X.Org Server Extension, version 0.3
(==) AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "dbe"
(II) Loading /usr/lib64/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
	compiled for 1.3.0, module version = 1.0.0
	Module class: X.Org Server Extension
	ABI class: X.Org Server Extension, version 0.3
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "freetype"
(II) Loading /usr/lib64/xorg/modules/fonts//libfreetype.so
(II) Module freetype: vendor="X.Org Foundation & the After X-TT Project"
	compiled for 1.3.0, module version = 2.1.0
	Module class: X.Org Font Renderer
	ABI class: X.Org Font Renderer, version 0.5
(II) Loading font FreeType
(II) LoadModule: "type1"
(II) Loading /usr/lib64/xorg/modules/fonts//libtype1.so
(II) Module type1: vendor="X.Org Foundation"
	compiled for 1.3.0, module version = 1.0.2
	Module class: X.Org Font Renderer
	ABI class: X.Org Font Renderer, version 0.5
(II) Loading font Type1
(II) LoadModule: "intel"
(II) Loading /usr/lib64/xorg/modules/drivers//intel_drv.so
(II) Module intel: vendor="X.Org Foundation"
	compiled for 1.3.0, module version = 2.1.1
	Module class: X.Org Video Driver
	ABI class: X.Org Video Driver, version 1.2
(II) LoadModule: "mouse"
(II) Loading /usr/lib64/xorg/modules/input//mouse_drv.so
(II) Module mouse: vendor="X.Org Foundation"
	compiled for 1.3.0, module version = 1.2.2
	Module class: X.Org XInput Driver
	ABI class: X.Org XInput driver, version 0.7
(II) LoadModule: "kbd"
(II) Loading /usr/lib64/xorg/modules/input//kbd_drv.so
(II) Module kbd: vendor="X.Org Foundation"
	compiled for 1.3.0, module version = 1.1.0
	Module class: X.Org XInput Driver
	ABI class: X.Org XInput driver, version 0.7
(II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
	i810-dc100, i810e, i815, i830M, 845G, 852GM/855GM, 865G, 915G,
	E7221 (i915), 915GM, 945G, 945GM, 945GME, 965G, 965G, 965Q, 946GZ,
	965GM, 965GME/GLE, G33, Q35, Q33
(II) Primary Device is: PCI 00:02:0
(WW) intel: No matching Device section for instance (BusID PCI:0:2:1) found
(--) Chipset 945GM found
(II) resource ranges after xf86ClaimFixedResources() call:
	[0] -1	0	0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
	[1] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[2] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[3] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[4] -1	0	0xfdaff000 - 0xfdaff7ff (0x800) MX[B]
	[5] -1	0	0xfddff000 - 0xfddfffff (0x1000) MX[B]
	[6] -1	0	0xfdbff000 - 0xfdbfffff (0x1000) MX[B]
	[7] -1	0	0xfdfff000 - 0xfdfff3ff (0x400) MX[B]
	[8] -1	0	0xfdff8000 - 0xfdffbfff (0x4000) MX[B]
	[9] -1	0	0xfdf00000 - 0xfdf7ffff (0x80000) MX[B](B)
	[10] -1	0	0xfdf80000 - 0xfdfbffff (0x40000) MX[B](B)
	[11] -1	0	0xd0000000 - 0xdfffffff (0x10000000) MX[B](B)
	[12] -1	0	0xfde80000 - 0xfdefffff (0x80000) MX[B](B)
	[13] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[14] -1	0	0x00000000 - 0x000000ff (0x100) IX[B]
	[15] -1	0	0x0000de00 - 0x0000de7f (0x80) IX[B]
	[16] -1	0	0x0000df00 - 0x0000df1f (0x20) IX[B]
	[17] -1	0	0x0000ee00 - 0x0000eeff (0x100) IX[B]
	[18] -1	0	0x0000ce00 - 0x0000ceff (0x100) IX[B]
	[19] -1	0	0x00000500 - 0x0000051f (0x20) IX[B]
	[20] -1	0	0x0000fa00 - 0x0000fa0f (0x10) IX[B]
	[21] -1	0	0x000001f0 - 0x000001f0 (0x1) IX[B]
	[22] -1	0	0x000001f0 - 0x000001f7 (0x8) IX[B]
	[23] -1	0	0x000001f0 - 0x000001f0 (0x1) IX[B]
	[24] -1	0	0x000001f0 - 0x000001f7 (0x8) IX[B]
	[25] -1	0	0x0000fb00 - 0x0000fb1f (0x20) IX[B]
	[26] -1	0	0x0000fc00 - 0x0000fc1f (0x20) IX[B]
	[27] -1	0	0x0000fd00 - 0x0000fd1f (0x20) IX[B]
	[28] -1	0	0x0000fe00 - 0x0000fe1f (0x20) IX[B]
	[29] -1	0	0x0000ff00 - 0x0000ff07 (0x8) IX[B](B)
(II) resource ranges after probing:
	[0] -1	0	0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
	[1] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[2] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[3] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[4] -1	0	0xfdaff000 - 0xfdaff7ff (0x800) MX[B]
	[5] -1	0	0xfddff000 - 0xfddfffff (0x1000) MX[B]
	[6] -1	0	0xfdbff000 - 0xfdbfffff (0x1000) MX[B]
	[7] -1	0	0xfdfff000 - 0xfdfff3ff (0x400) MX[B]
	[8] -1	0	0xfdff8000 - 0xfdffbfff (0x4000) MX[B]
	[9] -1	0	0xfdf00000 - 0xfdf7ffff (0x80000) MX[B](B)
	[10] -1	0	0xfdf80000 - 0xfdfbffff (0x40000) MX[B](B)
	[11] -1	0	0xd0000000 - 0xdfffffff (0x10000000) MX[B](B)
	[12] -1	0	0xfde80000 - 0xfdefffff (0x80000) MX[B](B)
	[13] 0	0	0x000a0000 - 0x000affff (0x10000) MS[B]
	[14] 0	0	0x000b0000 - 0x000b7fff (0x8000) MS[B]
	[15] 0	0	0x000b8000 - 0x000bffff (0x8000) MS[B]
	[16] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[17] -1	0	0x00000000 - 0x000000ff (0x100) IX[B]
	[18] -1	0	0x0000de00 - 0x0000de7f (0x80) IX[B]
	[19] -1	0	0x0000df00 - 0x0000df1f (0x20) IX[B]
	[20] -1	0	0x0000ee00 - 0x0000eeff (0x100) IX[B]
	[21] -1	0	0x0000ce00 - 0x0000ceff (0x100) IX[B]
	[22] -1	0	0x00000500 - 0x0000051f (0x20) IX[B]
	[23] -1	0	0x0000fa00 - 0x0000fa0f (0x10) IX[B]
	[24] -1	0	0x000001f0 - 0x000001f0 (0x1) IX[B]
	[25] -1	0	0x000001f0 - 0x000001f7 (0x8) IX[B]
	[26] -1	0	0x000001f0 - 0x000001f0 (0x1) IX[B]
	[27] -1	0	0x000001f0 - 0x000001f7 (0x8) IX[B]
	[28] -1	0	0x0000fb00 - 0x0000fb1f (0x20) IX[B]
	[29] -1	0	0x0000fc00 - 0x0000fc1f (0x20) IX[B]
	[30] -1	0	0x0000fd00 - 0x0000fd1f (0x20) IX[B]
	[31] -1	0	0x0000fe00 - 0x0000fe1f (0x20) IX[B]
	[32] -1	0	0x0000ff00 - 0x0000ff07 (0x8) IX[B](B)
	[33] 0	0	0x000003b0 - 0x000003bb (0xc) IS[B]
	[34] 0	0	0x000003c0 - 0x000003df (0x20) IS[B]
(II) Setting vga for screen 0.
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Loading /usr/lib64/xorg/modules//libint10.so
(II) Module int10: vendor="X.Org Foundation"
	compiled for 1.3.0, module version = 1.0.0
	ABI class: X.Org Video Driver, version 1.2
(II) Loading sub module "vbe"
(II) LoadModule: "vbe"
(II) Loading /usr/lib64/xorg/modules//libvbe.so
(II) Module vbe: vendor="X.Org Foundation"
	compiled for 1.3.0, module version = 1.1.0
	ABI class: X.Org Video Driver, version 1.2
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/lib64/xorg/modules//libvgahw.so
(II) Module vgahw: vendor="X.Org Foundation"
	compiled for 1.3.0, module version = 0.1.0
	ABI class: X.Org Video Driver, version 1.2
(**) intel(0): Depth 24, (--) framebuffer bpp 32
(==) intel(0): RGB weight 888
(==) intel(0): Default visual is TrueColor
(II) intel(0): Integrated Graphics Chipset: Intel(R) 945GM
(--) intel(0): Chipset: "945GM"
(--) intel(0): Linear framebuffer at 0xD0000000
(--) intel(0): IO registers at addr 0xFDE80000
(II) intel(0): 2 display pipes available.
(==) intel(0): Using XAA for acceleration
(--) intel(0): Will try to allocate texture pool for old Mesa 3D driver.
(II) intel(0): Will try to reserve 32768 kiB of AGP aperture space
	for the DRM memory manager.
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"(II) Module already built-in
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"(II) Module already built-in
(II) intel(0): Output VGA using monitor section Monitor0
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): Output LVDS has no monitor section
(II) intel(0): I2C bus "LVDSDDC_C" initialized.
(II) intel(0): I2C device "LVDSDDC_C:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "LVDSDDC_C:ddc2" removed.
(II) intel(0): EDID for output LVDS
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Reloading /usr/lib64/xorg/modules//libint10.so
(II) intel(0): initializing int10
(WW) intel(0): Bad V_BIOS checksum
(II) intel(0): Primary V_BIOS segment is: 0xc000
(II) intel(0): VESA BIOS detected
(II) intel(0): VESA VBE Version 3.0
(II) intel(0): VESA VBE Total Mem: 7872 kB
(II) intel(0): VESA VBE OEM: Intel(r) 82945GM Chipset Family Graphics Chip Accelerated VGA BIOS
(II) intel(0): VESA VBE OEM Software Rev: 1.0
(II) intel(0): VESA VBE OEM Vendor: Intel Corporation
(II) intel(0): VESA VBE OEM Product: Intel(r) 82945GM Chipset Family Graphics Controller
(II) intel(0): VESA VBE OEM Product Rev: Hardware Version 0.0
(II) intel(0): I2C bus "SDVOCTRL_E for SDVOB" initialized.
(II) intel(0): I2C device "SDVOCTRL_E for SDVOB:SDVO Controller B" registered at address 0x70.
(II) intel(0): I2C bus "SDVOB DDC Bus" initialized.
(II) intel(0): Output TMDS-1 using monitor section Monitor0
(II) intel(0): SDVO device VID/DID: 02:43.00, clock range 25.0MHz - 200.0MHz, input 1: Y, input 2: N, output 1: Y, output 2: N
(II) intel(0): I2C bus "SDVOCTRL_E for SDVOC" initialized.
(II) intel(0): I2C device "SDVOCTRL_E for SDVOC:SDVO Controller C" registered at address 0x72.
(II) intel(0): I2C bus "SDVOC DDC Bus" initialized.
(II) intel(0): Output TMDS-2 has no monitor section
(II) intel(0): SDVO device VID/DID: 02:47.02, clock range 25.0MHz - 165.0MHz, input 1: Y, input 2: N, output 1: Y, output 2: N
(II) intel(0): Output TV has no monitor section
(II) intel(0): Current clock rate multiplier: 1
(II) intel(0): Current clock rate multiplier: 1
(II) intel(0): Output VGA disconnected
(II) intel(0): EDID for output VGA
(II) intel(0): Output LVDS connected
(II) intel(0): I2C device "LVDSDDC_C:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "LVDSDDC_C:ddc2" removed.
(II) intel(0): EDID for output LVDS
(II) intel(0): Not using default mode "1152x864" (exceeds panel dimensions)
(II) intel(0): Not using default mode "1280x960" (exceeds panel dimensions)
(II) intel(0): Not using default mode "1280x960" (exceeds panel dimensions)
(II) intel(0): Not using default mode "1280x1024" (exceeds panel dimensions)
(II) intel(0): Not using default mode "1280x1024" (exceeds panel dimensions)
(II) intel(0): Not using default mode "1280x1024" (exceeds panel dimensions)
(II) intel(0): Not using default mode "1600x1200" (exceeds panel dimensions)
(II) intel(0): Not using default mode "1600x1200" (exceeds panel dimensions)
(II) intel(0): Not using default mode "1600x1200" (exceeds panel dimensions)
(II) intel(0): Not using default mode "1600x1200" (exceeds panel dimensions)
(II) intel(0): Not using default mode "1600x1200" (exceeds panel dimensions)
(II) intel(0): Not using default mode "1792x1344" (exceeds panel dimensions)
(II) intel(0): Not using default mode "1792x1344" (exceeds panel dimensions)
(II) intel(0): Not using default mode "1856x1392" (exceeds panel dimensions)
(II) intel(0): Not using default mode "1856x1392" (exceeds panel dimensions)
(II) intel(0): Not using default mode "1920x1440" (exceeds panel dimensions)
(II) intel(0): Not using default mode "1920x1440" (exceeds panel dimensions)
(II) intel(0): Not using default mode "1152x768" (exceeds panel dimensions)
(II) intel(0): Not using default mode "1400x1050" (exceeds panel dimensions)
(II) intel(0): Not using default mode "1400x1050" (exceeds panel dimensions)
(II) intel(0): Not using default mode "1600x1024" (exceeds panel dimensions)
(II) intel(0): Not using default mode "1920x1440" (exceeds panel dimensions)
(II) intel(0): Not using default mode "2048x1536" (exceeds panel dimensions)
(II) intel(0): Not using default mode "2048x1536" (exceeds panel dimensions)
(II) intel(0): Not using default mode "2048x1536" (exceeds panel dimensions)
(II) intel(0): Printing probed modes for output LVDS
(II) intel(0): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 (48.4 kHz)
(II) intel(0): Modeline "1024x768"x85.0   94.50  1024 1072 1168 1376  768 769 772 808 +hsync +vsync (68.7 kHz)
(II) intel(0): Modeline "1024x768"x75.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz)
(II) intel(0): Modeline "1024x768"x70.1   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync (56.5 kHz)
(II) intel(0): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz)
(II) intel(0): Modeline "832x624"x74.6   57.28  832 864 928 1152  624 625 628 667 -hsync -vsync (49.7 kHz)
(II) intel(0): Modeline "800x600"x85.1   56.30  800 832 896 1048  600 601 604 631 +hsync +vsync (53.7 kHz)
(II) intel(0): Modeline "800x600"x72.2   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync (48.1 kHz)
(II) intel(0): Modeline "800x600"x75.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz)
(II) intel(0): Modeline "800x600"x60.3   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz)
(II) intel(0): Modeline "800x600"x56.2   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz)
(II) intel(0): Modeline "640x480"x85.0   36.00  640 696 752 832  480 481 484 509 -hsync -vsync (43.3 kHz)
(II) intel(0): Modeline "640x480"x72.8   31.50  640 664 704 832  480 489 492 520 -hsync -vsync (37.9 kHz)
(II) intel(0): Modeline "640x480"x75.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz)
(II) intel(0): Modeline "640x480"x59.9   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz)
(II) intel(0): Modeline "720x400"x85.0   35.50  720 756 828 936  400 401 404 446 -hsync +vsync (37.9 kHz)
(II) intel(0): Modeline "640x400"x85.1   31.50  640 672 736 832  400 401 404 445 -hsync +vsync (37.9 kHz)
(II) intel(0): Modeline "640x350"x85.1   31.50  640 672 736 832  350 382 385 445 +hsync -vsync (37.9 kHz)
(II) intel(0): Output TMDS-1 connected
(II) intel(0): I2C device "SDVOB DDC Bus:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "SDVOB DDC Bus:ddc2" removed.
(II) intel(0): EDID for output TMDS-1
(II) intel(0): Manufacturer: HWP  Model: a72  Serial#: 16843009
(II) intel(0): Year: 2007  Week: 33
(II) intel(0): EDID Version: 1.3
(II) intel(0): Digital Display Input
(II) intel(0): Max H-Image Size [cm]: horiz.: 41  vert.: 31
(II) intel(0): Gamma: 2.20
(II) intel(0): DPMS capabilities: StandBy Suspend Off; RGB/Color Display
(II) intel(0): Default color space is primary color space
(II) intel(0): First detailed timing is preferred mode
(II) intel(0): redX: 0.639 redY: 0.342   greenX: 0.290 greenY: 0.615
(II) intel(0): blueX: 0.146 blueY: 0.072   whiteX: 0.313 whiteY: 0.329
(II) intel(0): Supported VESA Video Modes:
(II) intel(0): 720x400@70Hz
(II) intel(0): 640x480@60Hz
(II) intel(0): 640x480@75Hz
(II) intel(0): 800x600@60Hz
(II) intel(0): 832x624@75Hz
(II) intel(0): 1024x768@60Hz
(II) intel(0): 1024x768@75Hz
(II) intel(0): 1280x1024@75Hz
(II) intel(0): 1152x870@75Hz
(II) intel(0): Manufacturer's mask: 0
(II) intel(0): Supported Future Video Modes:
(II) intel(0): #0: hsize: 640  vsize 480  refresh: 85  vid: 22833
(II) intel(0): #1: hsize: 800  vsize 600  refresh: 85  vid: 22853
(II) intel(0): #2: hsize: 1024  vsize 768  refresh: 85  vid: 22881
(II) intel(0): #3: hsize: 1280  vsize 960  refresh: 60  vid: 16513
(II) intel(0): #4: hsize: 1280  vsize 1024  refresh: 60  vid: 32897
(II) intel(0): #5: hsize: 1280  vsize 1024  refresh: 85  vid: 39297
(II) intel(0): #6: hsize: 1600  vsize 1200  refresh: 60  vid: 16553
(II) intel(0): Supported additional Video Mode:
(II) intel(0): clock: 162.0 MHz   Image Size:  408 x 306 mm
(II) intel(0): h_active: 1600  h_sync: 1664  h_sync_end 1856 h_blank_end 2160 h_border: 0
(II) intel(0): v_active: 1200  v_sync: 1201  v_sync_end 1204 v_blanking: 1250 v_border: 0
(II) intel(0): Ranges: V min: 48  V max: 85 Hz, H min: 30  H max: 92 kHz, PixClock max 170 MHz
(II) intel(0): Monitor name: HP LP2065
(II) intel(0): Serial No: PLG73300J2
(II) intel(0): EDID (in hex):
(II) intel(0): 	00ffffffffffff0022f0720a01010101
(II) intel(0): 	2111010380291f78eea6a5a3574a9d25
(II) intel(0): 	125054a52b8031594559615981408180
(II) intel(0): 	8199a9400101483f403062b0324040c0
(II) intel(0): 	130098321100001e000000fd0030551e
(II) intel(0): 	5c11000a202020202020000000fc0048
(II) intel(0): 	50204c50323036350a202020000000ff
(II) intel(0): 	00504c4737333330304a320a20200086
(II) intel(0): EDID vendor "HWP", prod id 2674
(II) intel(0): Not using default mode "640x350" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "640x400" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "720x400" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "640x480" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "640x480" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "640x480" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "640x480" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "1152x864" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "1280x960" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "1280x960" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "1280x1024" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "1280x1024" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "1280x1024" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "1600x1200" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "1600x1200" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "1600x1200" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "1600x1200" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "1600x1200" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "1792x1344" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "1792x1344" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "1856x1392" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "1856x1392" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "832x624" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "1152x768" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "1400x1050" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "1400x1050" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "1600x1024" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan)
(II) intel(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan)
(II) intel(0): Printing probed modes for output TMDS-1
(II) intel(0): Modeline "1600x1200"x60.0  162.00  1600 1664 1856 2160  1200 1201 1204 1250 +hsync +vsync (75.0 kHz)
(II) intel(0): Modeline "1600x1200"x59.9  161.00  1600 1712 1880 2160  1200 1203 1207 1245 -hsync +vsync (74.5 kHz)
(II) intel(0): Modeline "1600x1200_60.0"x60.0  160.96  1600 1704 1880 2160  1200 1201 1204 1242 -hsync +vsync (74.5 kHz)
(II) intel(0): Modeline "1280x1024"x84.8  159.50  1280 1376 1512 1744  1024 1027 1034 1078 -hsync +vsync (91.5 kHz)
(II) intel(0): Modeline "1280x1024"x75.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) intel(0): Modeline "1280x1024"x59.9  109.00  1280 1368 1496 1712  1024 1027 1034 1063 -hsync +vsync (63.7 kHz)
(II) intel(0): Modeline "1280x960"x59.9  101.25  1280 1360 1488 1696  960 963 967 996 -hsync +vsync (59.7 kHz)
(II) intel(0): Modeline "1152x864"x75.0  108.00  1152 1216 1344 1600  864 865 868 900 +hsync +vsync (67.5 kHz)
(II) intel(0): Modeline "1024x768"x84.9   94.50  1024 1096 1200 1376  768 771 775 809 -hsync +vsync (68.7 kHz)
(II) intel(0): Modeline "1024x768"x75.1   78.80  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.1 kHz)
(II) intel(0): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz)
(II) intel(0): Modeline "832x624"x74.6   57.28  832 864 928 1152  624 625 628 667 -hsync -vsync (49.7 kHz)
(II) intel(0): Modeline "800x600"x84.9   56.75  800 848 928 1056  600 603 607 633 -hsync +vsync (53.7 kHz)
(II) intel(0): Modeline "800x600"x60.3   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz)
(II) intel(0): Modeline "640x480"x84.6   35.00  640 664 728 816  480 483 487 507 -hsync +vsync (42.9 kHz)
(II) intel(0): Modeline "640x480"x75.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz)
(II) intel(0): Modeline "640x480"x60.0   25.20  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz)
(II) intel(0): Modeline "720x400"x70.1   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz)
(II) intel(0): Output TMDS-2 disconnected
(II) intel(0): EDID for output TMDS-2
(II) intel(0): Output TV disconnected
(II) intel(0): EDID for output TV
(II) intel(0): Output VGA disconnected
(II) intel(0): Output LVDS connected
(II) intel(0): Output TMDS-1 connected
(II) intel(0): Output TMDS-2 disconnected
(II) intel(0): Output TV disconnected
(II) intel(0): Output LVDS using initial mode 1024x768
(II) intel(0): Output TMDS-1 using initial mode 1024x768
(II) intel(0): Monitoring connected displays enabled
(II) intel(0): detected 256 kB GTT.
(II) intel(0): detected 7932 kB stolen memory.
(==) intel(0): video overlay key set to 0x101fe
(==) intel(0): Will not try to enable page flipping
(==) intel(0): Triple buffering disabled
(==) intel(0): Using gamma correction (1.0, 1.0, 1.0)
(==) intel(0): DPI set to (75, 75)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib64/xorg/modules//libfb.so
(II) Module fb: vendor="X.Org Foundation"
	compiled for 1.3.0, module version = 1.0.0
	ABI class: X.Org ANSI C Emulation, version 0.3
(II) Loading sub module "xaa"
(II) LoadModule: "xaa"
(II) Loading /usr/lib64/xorg/modules//libxaa.so
(II) Module xaa: vendor="X.Org Foundation"
	compiled for 1.3.0, module version = 1.2.0
	ABI class: X.Org Video Driver, version 1.2
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"(II) Module already built-in
(II) intel(0): Comparing regs from server start up to After PreInit
(==) Depth 24 pixmap format is 32 bpp
(II) do I need RAC?  No, I don't.
(II) resource ranges after preInit:
	[0] 0	0	0xfdf80000 - 0xfdfbffff (0x40000) MS[B]
	[1] 0	0	0xd0000000 - 0xdfffffff (0x10000000) MS[B]
	[2] 0	0	0xfde80000 - 0xfdefffff (0x80000) MS[B]
	[3] -1	0	0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
	[4] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[5] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[6] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[7] -1	0	0xfdaff000 - 0xfdaff7ff (0x800) MX[B]
	[8] -1	0	0xfddff000 - 0xfddfffff (0x1000) MX[B]
	[9] -1	0	0xfdbff000 - 0xfdbfffff (0x1000) MX[B]
	[10] -1	0	0xfdfff000 - 0xfdfff3ff (0x400) MX[B]
	[11] -1	0	0xfdff8000 - 0xfdffbfff (0x4000) MX[B]
	[12] -1	0	0xfdf00000 - 0xfdf7ffff (0x80000) MX[B](B)
	[13] -1	0	0xfdf80000 - 0xfdfbffff (0x40000) MX[B](B)
	[14] -1	0	0xd0000000 - 0xdfffffff (0x10000000) MX[B](B)
	[15] -1	0	0xfde80000 - 0xfdefffff (0x80000) MX[B](B)
	[16] 0	0	0x000a0000 - 0x000affff (0x10000) MS[B](OprD)
	[17] 0	0	0x000b0000 - 0x000b7fff (0x8000) MS[B](OprD)
	[18] 0	0	0x000b8000 - 0x000bffff (0x8000) MS[B](OprD)
	[19] 0	0	0x0000ff00 - 0x0000ff07 (0x8) IS[B]
	[20] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[21] -1	0	0x00000000 - 0x000000ff (0x100) IX[B]
	[22] -1	0	0x0000de00 - 0x0000de7f (0x80) IX[B]
	[23] -1	0	0x0000df00 - 0x0000df1f (0x20) IX[B]
	[24] -1	0	0x0000ee00 - 0x0000eeff (0x100) IX[B]
	[25] -1	0	0x0000ce00 - 0x0000ceff (0x100) IX[B]
	[26] -1	0	0x00000500 - 0x0000051f (0x20) IX[B]
	[27] -1	0	0x0000fa00 - 0x0000fa0f (0x10) IX[B]
	[28] -1	0	0x000001f0 - 0x000001f0 (0x1) IX[B]
	[29] -1	0	0x000001f0 - 0x000001f7 (0x8) IX[B]
	[30] -1	0	0x000001f0 - 0x000001f0 (0x1) IX[B]
	[31] -1	0	0x000001f0 - 0x000001f7 (0x8) IX[B]
	[32] -1	0	0x0000fb00 - 0x0000fb1f (0x20) IX[B]
	[33] -1	0	0x0000fc00 - 0x0000fc1f (0x20) IX[B]
	[34] -1	0	0x0000fd00 - 0x0000fd1f (0x20) IX[B]
	[35] -1	0	0x0000fe00 - 0x0000fe1f (0x20) IX[B]
	[36] -1	0	0x0000ff00 - 0x0000ff07 (0x8) IX[B](B)
	[37] 0	0	0x000003b0 - 0x000003bb (0xc) IS[B](OprU)
	[38] 0	0	0x000003c0 - 0x000003df (0x20) IS[B](OprU)
(II) intel(0): Kernel reported 488960 total, 1 used
(II) intel(0): I830CheckAvailableMemory: 1955836 kB available
(==) intel(0): VideoRam: 262144 KB
(II) intel(0): Attempting memory allocation with tiled buffers and 
	       large DRI memory manager reservation:
(II) intel(0): Allocating 5820 scanlines for pixmap cache
(II) intel(0): Success.
(II) intel(0): Increasing the scanline pitch to allow tiling mode (1600 -> 2048).
(II) intel(0): Memory allocation layout:
(II) intel(0): 0x00000000-0x0001ffff: ring buffer (128 kB)
(II) intel(0): 0x00020000-0x00029fff: HW cursors (40 kB, 0x        7f820000 physical)
(II) intel(0): 0x0002a000-0x00031fff: logical 3D context (32 kB)
(II) intel(0): 0x00032000-0x00032fff: overlay registers (4 kB, 0x        7f832000 physical)
(II) intel(0): 0x00040000-0x03a37fff: front buffer (59360 kB)
(II) intel(0): 0x007bf000:            end of stolen memory
(II) intel(0): 0x03a38000-0x03a47fff: xaa scratch (64 kB)
(II) intel(0): 0x04000000-0x04ffffff: back buffer (12800 kB)
(II) intel(0): 0x05000000-0x05ffffff: depth buffer (12800 kB)
(II) intel(0): 0x06000000-0x07ffffff: DRI memory manager (32768 kB)
(II) intel(0): 0x08000000-0x09ffffff: textures (32768 kB)
(II) intel(0): 0x10000000:            end of aperture
(II) intel(0): front buffer is not tiled
(II) intel(0): back buffer is tiled
(II) intel(0): depth buffer is tiled
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 7, (OK)
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 7, (OK)
drmOpenByBusid: Searching for BusID pci:0000:00:02.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 7, (OK)
drmOpenByBusid: drmOpenMinor returns 7
drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
(II) intel(0): [drm] DRM interface version 1.3
(II) intel(0): [drm] created "i915" driver at busid "pci:0000:00:02.0"
(II) intel(0): [drm] added 8192 byte SAREA at 0x2efff000
(II) intel(0): [drm] mapped SAREA 0x2efff000 to 0x2b01b17c5000
(II) intel(0): [drm] framebuffer handle = 0xd0040000
(II) intel(0): [drm] added 1 reserved context for kernel
(II) intel(0): Unable to use TTM-based memory manager with DRM version 1.6
(II) intel(0): [drm] Registers = 0xfde80000
(II) intel(0): [drm] ring buffer = 0xd0000000
(II) intel(0): [drm] init sarea width,height = 1600 x 1600 (pitch 2048)
(II) intel(0): [drm] Mapping front buffer
(II) intel(0): [drm] Front Buffer = 0x2fff9000
(II) intel(0): [drm] Back Buffer = 0xd4000000
(II) intel(0): [drm] Depth Buffer = 0xd5000000
(II) intel(0): [drm] textures = 0xd8000000
(II) intel(0): [drm] Initialized kernel agp heap manager, 33554432
(II) intel(0): [dri] visual configs initialized
(II) intel(0): Page Flipping disabled
(==) intel(0): Write-combining range (0xd0000000,0x10000000)
(II) intel(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(II) intel(0): Using XFree86 Acceleration Architecture (XAA)
	Screen to screen bit blits
	Solid filled rectangles
	8x8 mono pattern filled rectangles
	Indirect CPU to Screen color expansion
	Solid Horizontal and Vertical Lines
	Offscreen Pixmaps
	Setting up tile and stipple cache:
		32 128x128 slots
		32 256x256 slots
		16 512x512 slots
(==) intel(0): Backing store disabled
(==) intel(0): Silken mouse enabled
(II) intel(0): Initializing HW Cursor
(II) intel(0): Current clock rate multiplier: 1
(II) intel(0): Current clock rate multiplier: 1
(II) intel(0): xf86BindGARTMemory: bind key 0 at 0x007bf000 (pgoffset 1983)
(II) intel(0): xf86BindGARTMemory: bind key 1 at 0x03a38000 (pgoffset 14904)
(II) intel(0): xf86BindGARTMemory: bind key 2 at 0x04000000 (pgoffset 16384)
(II) intel(0): xf86BindGARTMemory: bind key 3 at 0x05000000 (pgoffset 20480)
(II) intel(0): xf86BindGARTMemory: bind key 4 at 0x08000000 (pgoffset 32768)
(II) intel(0): Output configuration:
(II) intel(0):   Pipe A is on
(II) intel(0):   Display plane A is now enabled and connected to pipe A.
(II) intel(0):   Pipe B is on
(II) intel(0):   Display plane B is now enabled and connected to pipe B.
(II) intel(0):   Output VGA is connected to pipe none
(II) intel(0):   Output LVDS is connected to pipe B
(II) intel(0):   Output TMDS-1 is connected to pipe A
(II) intel(0):   Output TMDS-2 is connected to pipe none
(II) intel(0):   Output TV is connected to pipe none
(**) Option "dpms"
(**) intel(0): DPMS enabled
(II) intel(0): Set up textured video
(II) intel(0): Set up overlay video
(II) intel(0): X context handle = 0x1
(II) intel(0): [drm] installed DRM signal handler
(II) intel(0): [DRI] installation complete
(II) intel(0): [drm] dma control initialized, using IRQ 16
(II) intel(0): direct rendering: Enabled
(II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
(--) RandR disabled
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-APPGROUP
(II) Initializing built-in extension XAccessControlExtension
(II) Initializing built-in extensi

Voltago · Post by **Voltago** » Sun Jan 27, 2008 8:58 pm

dlaor: yes, the intel-drivers of version 2.0 or newer don't need 915resolution any more. As xorg-server's autodetection capabilities have somewhat improved over the last years, first try a very minimal xorg.conf

Code: Select all

Section "Device"
    Identifier  "intel"
    Driver      "intel"
EndSection

Section "Screen"
    Identifier  "screen0"
    Device      "intel"
EndSection

and add additional entries as needed. You probably won't need the "InputDevice" and "DRI" sections any more.
You can determine runtime support for different screen modi using

Code: Select all

xrandr

If this still doesn't give you 1600x2000, you'll probably want to add "Display" subsections or ModeLines (see Gentoo Xorg HowTo), but first you should try the simple method.

robinswan · Post by **robinswan** » Mon Jan 28, 2008 2:25 am

The same problem have made my headache for long time!
http://forums.gentoo.org/viewtopic-t-63 ... ight-.html
and I also tied to use 915resolution, it don't amend any issues.

I get the monitor parameter via the below command line,
and attach it to Monitor section of xorg.conf .

Code: Select all

 $ gtf 1440 900 60

  # 1440x900 @ 60.00 Hz (GTF) hsync: 55.92 kHz; pclk: 106.47 MHz
  Modeline "1440x900_60.00"  106.47  1440 1520 1672 1904  900 901 904 932  -HSync +Vsync

ofter I entry gnome environment, change the screen resolution via
"System" --> "Screen Resolution"
select parameter to : resolution = 1440x900 , refresh = 60

Then the monitor will work in its native resolution!
good luck!

xorg.conf

Code: Select all

Section "ServerLayout"
        Identifier     "X.org Configured"
        Screen      0  "Screen0" 0 0
        InputDevice    "Mouse0" "CorePointer"
        InputDevice    "Keyboard0" "CoreKeyboard"
EndSection

Section "Files"
        RgbPath      "/usr/share/X11/rgb"
        ModulePath   "/usr/lib/xorg/modules"
        FontPath     "/usr/share/fonts/misc/"
        FontPath     "/usr/share/fonts/TTF/"
        FontPath     "/usr/share/fonts/OTF"
        FontPath     "/usr/share/fonts/Type1/"
        FontPath     "/usr/share/fonts/100dpi/"
        FontPath     "/usr/share/fonts/75dpi/"
EndSection

Section "Module"
        Load  "dri"
        Load  "GLcore"
        Load  "record"
        Load  "xtrap"
        Load  "dbe"
        Load  "glx"
        Load  "extmod"
        Load  "freetype"
        Load  "type1"
EndSection

Section "InputDevice"
        Identifier  "Keyboard0"
        Driver      "kbd"
EndSection

Section "InputDevice"
        Identifier  "Mouse0"
        Driver      "mouse"
        Option      "Protocol" "auto"
        Option      "Device" "/dev/input/mice"
        Option      "ZAxisMapping" "4 5 6 7"
EndSection

Section "Monitor"
        #DisplaySize      340   270     # mm
        Identifier   "Monitor0"
        VendorName   "BNQ"
        ModelName    "BenQ FP71G"
 ### Comment all HorizSync and VertRefresh values to use DDC:
        HorizSync    31.0 - 83.0
        VertRefresh  56.0 - 76.0
        Option      "DPMS"
        # 1440x900 @ 60.00 Hz (GTF) hsync: 55.92 kHz; pclk: 106.47 MHz
        Modeline "1440x900_60.00"  106.47  1440 1520 1672 1904  900 901 904 932  -HSync +Vsync
EndSection

Section "Device"
        ### Available Driver options are:-
        ### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
        ### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
        ### [arg]: arg optional
        #Option     "NoAccel"                   # [<bool>]
        #Option     "SWcursor"                  # [<bool>]
        #Option     "ColorKey"                  # <i>
        #Option     "CacheLines"                # <i>
        #Option     "Dac6Bit"                   # [<bool>]
        #Option     "DRI"                       # [<bool>]
        #Option     "NoDDC"                     # [<bool>]
        #Option     "ShowCache"                 # [<bool>]
        #Option     "XvMCSurfaces"              # <i>
        #Option     "PageFlip"                  # [<bool>]
        Identifier  "Card0"
        Driver      "intel"
        VendorName  "Intel Corporation"
        BoardName   "82945G/GZ Integrated Graphics Controller"
        BusID       "PCI:0:2:0"
EndSection

Section "Screen"
        Identifier "Screen0"
        Device     "Card0"
        Monitor    "Monitor0"
        SubSection "Display"
                Viewport   0 0
                Depth     1
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth     4
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth     8
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth     15
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth     16
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth     24
                Modes   "1440x900@60"
        EndSubSection
EndSection

# if you want to use direct rendering
Section "DRI"
        Group 0
        Mode 0666
EndSection

dlaor · Post by **dlaor** » Tue Jan 29, 2008 12:16 am

First of all, many thanks for your replies Voltago and robinswan.

Voltago: I tried your minimal xorg.conf. Sadly it did not work: resolution is still 1024x768 and the same errors appear in Xorg.0.log:

Code: Select all

(II) intel(0): Not using default mode "640x350" (bad mode clock/interlace/doublescan)

... etc ...

(II) intel(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan)

Running xrandr gave

Code: Select all

Can't open display

Which is not good i guess

. Note that my display is connected via DVI and that my motherboard also has an LVDS connector. Nothing is connected to the latter, but X thinks there is:

Code: Select all

(II) intel(0): Output LVDS connected

Is it possible that xrandr tries to open this device, eg the non-existing device that X thinks is connected to the LVDS connector?? Is there a way to specify the display xrandr should look for (for example can I specify it should probe the DVI port or something like that?)

robinswan: I looked at posts about your problem. I have tried the same things that were suggested (i.e. adding the 830/915 driver to the kernel, not as module and emerging the acpid application), but to no avail. However, your problem is interesting since it gives the same error (bad mode clock/interlace/doublescan). On the other hand in your case X starts with the initial mode 1440x900, were you able to specify this initial mode somewhere? My X always starts with initial mode 1024x768, no matter what i set in xorg.conf.

After you solved the problem, did the bad mode clock/interlace/doublescan-errors disappear from your Xorg.0.log?

And when you ran xrandr, did it give the "Can't open display"-error? And after you solved it?

I also tried the Modeline options, but they did not work (see my xorg.conf above).

I see now that only a part of the Xorg.0.log was posted, here is the remaining part:

Code: Select all

(II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
(--) RandR disabled
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-APPGROUP
(II) Initializing built-in extension XAccessControlExtension
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension XFree86-Bigfont
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) Initializing built-in extension XEVIE
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 8, (OK)
drmOpenByBusid: Searching for BusID pci:0000:00:02.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 8, (OK)
drmOpenByBusid: drmOpenMinor returns 8
drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
(WW) AIGLX: 3D driver claims to not support visual 0x23
(WW) AIGLX: 3D driver claims to not support visual 0x24
(WW) AIGLX: 3D driver claims to not support visual 0x25
(WW) AIGLX: 3D driver claims to not support visual 0x26
(WW) AIGLX: 3D driver claims to not support visual 0x27
(WW) AIGLX: 3D driver claims to not support visual 0x28
(WW) AIGLX: 3D driver claims to not support visual 0x29
(WW) AIGLX: 3D driver claims to not support visual 0x2a
(WW) AIGLX: 3D driver claims to not support visual 0x2b
(WW) AIGLX: 3D driver claims to not support visual 0x2c
(WW) AIGLX: 3D driver claims to not support visual 0x2d
(WW) AIGLX: 3D driver claims to not support visual 0x2e
(WW) AIGLX: 3D driver claims to not support visual 0x2f
(WW) AIGLX: 3D driver claims to not support visual 0x30
(WW) AIGLX: 3D driver claims to not support visual 0x31
(WW) AIGLX: 3D driver claims to not support visual 0x32
(II) AIGLX: Loaded and initialized /usr/lib64/dri/i915_dri.so
(II) GLX: Initialized DRI GL provider for screen 0
(II) intel(0): Setting screen physical size to 270 x 203
(**) Option "Protocol" "auto"
(**) Mouse0: Device: "/dev/input/mice"
(**) Mouse0: Protocol: "auto"
(**) Option "CorePointer"
(**) Mouse0: Core Pointer
(**) Option "Device" "/dev/input/mice"
(==) Mouse0: Emulate3Buttons, Emulate3Timeout: 50
(**) Option "ZAxisMapping" "4 5 6 7"
(**) Mouse0: ZAxisMapping: buttons 4, 5, 6 and 7
(**) Mouse0: Buttons: 11
(**) Mouse0: Sensitivity: 1
(**) Option "CoreKeyboard"
(**) Keyboard0: Core Keyboard
(**) Option "Protocol" "standard"
(**) Keyboard0: Protocol: standard
(**) Option "AutoRepeat" "500 30"
(**) Option "XkbRules" "xorg"
(**) Keyboard0: XkbRules: "xorg"
(**) Option "XkbModel" "pc105"
(**) Keyboard0: XkbModel: "pc105"
(**) Option "XkbLayout" "us"
(**) Keyboard0: XkbLayout: "us"
(**) Option "CustomKeycodes" "off"
(**) Keyboard0: CustomKeycodes disabled
(II) XINPUT: Adding extended input device "Keyboard0" (type: KEYBOARD)
(II) XINPUT: Adding extended input device "Mouse0" (type: MOUSE)
(--) Mouse0: PnP-detected protocol: "ExplorerPS/2"
(II) Mouse0: ps2EnableDataReporting: succeeded
(II) intel(0): [drm] removed 1 reserved context for kernel
(II) intel(0): [drm] unmapping 8192 bytes of SAREA 0x2efff000 at 0x2b01b17c5000
(EE) intel(0): I830 Vblank Pipe Setup Failed 0
(EE) intel(0): I830 Vblank Pipe Setup Failed 0
(EE) intel(0): I830 Vblank Pipe Setup Failed 0
(II) intel(0): xf86UnbindGARTMemory: unbind key 0
(II) intel(0): xf86UnbindGARTMemory: unbind key 1
(II) intel(0): xf86UnbindGARTMemory: unbind key 2
(II) intel(0): xf86UnbindGARTMemory: unbind key 3
(II) intel(0): xf86UnbindGARTMemory: unbind key 4
FreeFontPath: FPE "/usr/share/fonts/misc/" refcount is 2, should be 1; fixing.

The last errors "(EE) intel(0): I830 Vblank Pipe Setup Failed 0" happen after closing X, so i guess they do not matter?

I am also still only using twm for X, but this should not give a problem right? Or can twm not use high resolutions?

robinswan · Post by **robinswan** » Tue Jan 29, 2008 2:24 am

Hi, dlaor:

I all most confirm those issues is the bug of xorg.
now my X is so unstable no my monitor native resolution.
some time it work in 1440x900@60 and some time do not!

we just wait xorg amend itself.

dlaor · Post by **dlaor** » Tue Jan 29, 2008 10:48 pm

The problem is now solved

.

xrandr gave the error "Can't open display" because I executed it outside X. When executed inside X it showed the possible resolutions for the (non-existing) LVDS monitor and the real monitor. I could then change the resolution of the real monitor to 1600x1200 and this all works.

So somehow X finds two monitors, one connected to LVDS, with max resolution 1024x768, and one connected to DVI, with max resolution 1600x1200. I guess it clones the desktop for these two monitors and thus sets the resolution of the desktop to the minimum resolution of these two, which is 1024x768. To stop this you can tell X to ignore the LVDS monitor as follows:

xorg.conf

Code: Select all

Section "Device"
  Identifier	"Intel 945GM"
  Driver	"intel"
  Option	"Monitor-TMDS-1" "HP LP2065" #assigns monitor section "HP LP2065" to the first DVI port
  Option	"Monitor-LVDS" "LVDS Virtual Monitor" #assigns monitor section "LVDS Virtual Monitor" to the LVDS port
EndSection

Section "Monitor"
  Identifier	"HP LP2065"
EndSection

Section "Monitor"
  Identifier	"LVDS Virtual Monitor"
  Option	"Ignore" "True" # Tells X.org to ignore this monitor
EndSection

Section "Screen"
  Identifier	"Default Screen"
  Device	"Intel 945GM"
  Monitor	"HP LP2065"
  DefaultDepth	24
  SubSection "Display"
    Depth	24
    Modes	"1600x1200"
  EndSubSection
EndSection

You can replace "Monitor-TMDS-1" by "Monitor-VGA" if you want to assign a monitor section to your VGA-port. Some cards use "Monitor-DVI" instead of "Monitor-TMDS". Of course my second DVI-port is denoted by "Monitor-TMDS-2", etc... All these names can be found in your Xorg.0.log.

Hurray! Now I can finally install xfce

.

Many thanks again to robinswan and voltago for helping me.

(robinswan: I looked at your Xorg.0.log but I don't think my solution can help you, since X only finds one monitor connected to your VGA-port and hence your resolution will not be reduced because of other (non-existing) monitors)

robinswan · Post by **robinswan** » Wed Jan 30, 2008 1:50 am

Congratulation ！
my problem still exist.
after I turn off power, and power up again, the X can not work in native resolution.
while I am waiting some of ten minutes and change the resolution to 1440x900 in gnome,
It will work !!

but the monitor alway work any time in Windows.