Gentoo Forums
Gentoo Forums
Gentoo Forums
Quick Search: in
wireless obtained wrong ip 169.254.154.94
View unanswered posts
View posts from last 24 hours

 
Reply to topic    Gentoo Forums Forum Index Networking & Security
View previous topic :: View next topic  
Author Message
ant1688
Tux's lil' helper
Tux's lil' helper


Joined: 03 May 2007
Posts: 138

PostPosted: Mon Feb 17, 2014 5:14 pm    Post subject: wireless obtained wrong ip 169.254.154.94 Reply with quote

dear all,

The wifi no longer work for days, alway popup login windows . I finally realize it is the problem of networkmanager. I unmergedv the networkmanager and its applet. The wifi works by dhcp for some hours, but no longer work when click remove all button in the wpa_supplicant gui. I could not recover it.

the wireless card received a wrong ip address:

Code:

 # ifconfig
enp2s0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 192.168.1.106  netmask 255.255.255.0  broadcast 255.255.255.255
        inet6 fe80::223:8bff:fe27:f4a7  prefixlen 64  scopeid 0x20<link>
        ether 00:23:8b:27:f4:a7  txqueuelen 1000  (Ethernet)
        RX packets 2035  bytes 1241129 (1.1 MiB)
        RX errors 0  dropped 19  overruns 0  frame 0
        TX packets 1680  bytes 253513 (247.5 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
        device interrupt 16 

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        inet6 ::1  prefixlen 128  scopeid 0x10<host>
        loop  txqueuelen 0  (Local Loopback)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

sit0: flags=193<UP,RUNNING,NOARP>  mtu 1480
        inet6 ::127.0.0.1  prefixlen 96  scopeid 0x90<compat,host>
        sit  txqueuelen 0  (IPv6-in-IPv4)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

wlp5s0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 169.254.154.94  netmask 255.255.0.0  broadcast 169.254.255.255
        inet6 fe80::221:ff:fe8b:d590  prefixlen 64  scopeid 0x20<link>
        ether 00:21:00:8b:d5:90  txqueuelen 1000  (Ethernet)
        RX packets 38  bytes 5548 (5.4 KiB)
        RX errors 0  dropped 0  overruns 0  frame 22468
        TX packets 277  bytes 42274 (41.2 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
        device interrupt 18 


I know the ip address shoudbe something like 192.168.1.xxx, but 169.254.154.94 .

my /etc/conf.d/net:
Code:
wpa_supplicant_wlp5s0="( "-Dnl80211" )"
modules_wlp5s0="( "wpa_supplicant" )"



my wpa_supplicant.conf:
Code:
ctrl_interface=DIR=/var/run/wpa_supplicant
ctrl_interface_group=wheel
update_config=1

network={
   ssid="xxxxxx"
   psk="xxxxxx"
   proto=RSN
   key_mgmt=WPA-PSK
   pairwise=TKIP
   auth_alg=OPEN
}


Code:
# lspci
00:00.0 Host bridge: Intel Corporation Mobile 945GSE Express Memory Controller Hub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GSE Express Integrated Graphics Controller (rev 03)
00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03)
00:1b.0 Audio device: Intel Corporation NM10/ICH7 Family High Definition Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 1 (rev 02)
00:1c.1 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 2 (rev 02)
00:1c.2 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 3 (rev 02)
00:1d.0 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 (rev 02)
00:1d.1 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 (rev 02)
00:1d.2 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 (rev 02)
00:1d.3 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 (rev 02)
00:1d.7 USB controller: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02)
00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7-M Family) SATA Controller [IDE mode] (rev 02)
00:1f.3 SMBus: Intel Corporation NM10/ICH7 Family SMBus Controller (rev 02)
02:00.0 Ethernet controller: Broadcom Corporation NetLink BCM5906M Fast Ethernet PCI Express (rev 02)
05:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01)


my driver is broadcom-sta, the b43 and other settings were blacklisted as required by broadcom-sta.

Thanks in advance.
Back to top
View user's profile Send private message
spike88
n00b
n00b


Joined: 16 Oct 2012
Posts: 17

PostPosted: Mon Feb 17, 2014 10:50 pm    Post subject: Reply with quote

I have not had any luck with the broadcom sta driver on my end b43 worked for me did you try to manually set the ip in the /etc/conf.d/net file or do you prefer dhcp
_________________
Gentoo Rocks thanks!
Back to top
View user's profile Send private message
ant1688
Tux's lil' helper
Tux's lil' helper


Joined: 03 May 2007
Posts: 138

PostPosted: Tue Feb 18, 2014 4:21 am    Post subject: Reply with quote

spike88 wrote:
I have not had any luck with the broadcom sta driver on my end b43 worked for me did you try to manually set the ip in the /etc/conf.d/net file or do you prefer dhcp


it has been working for years, until some updates weeks ago...
Back to top
View user's profile Send private message
chithanh
Developer
Developer


Joined: 05 Aug 2006
Posts: 1743
Location: Berlin, Germany

PostPosted: Tue Feb 18, 2014 7:11 pm    Post subject: Reply with quote

169.254.* is APIPA address, which means that no DHCP server could be reached. Try running dhcpcd manually on that interface (dhcpcd -k will remove an existing instance).

Also try setting the IP address manually and pinging hosts on the local network.
Back to top
View user's profile Send private message
ant1688
Tux's lil' helper
Tux's lil' helper


Joined: 03 May 2007
Posts: 138

PostPosted: Wed Feb 19, 2014 5:41 pm    Post subject: Reply with quote

chithanh wrote:
169.254.* is APIPA address, which means that no DHCP server could be reached. Try running dhcpcd manually on that interface (dhcpcd -k will remove an existing instance).

Also try setting the IP address manually and pinging hosts on the local network.


Thanks to chithanh.


Code:
 # dhcpcd -k
dhcpcd[2725]: sending signal 1 to pid 1904
dhcpcd[2725]: waiting for pid 1904 to exit

# dhcpcd wlp5s0
dhcpcd[2750]: version 6.2.0 starting
dhcpcd[2750]: DUID 00:01:00:01:1a:81:62:aa:00:23:8b:27:f4:a7
dhcpcd[2750]: wlp5s0: IAID 00:8b:d5:90
dhcpcd[2750]: wlp5s0: soliciting an IPv6 router
dhcpcd[2750]: wlp5s0: soliciting a DHCP lease
dhcpcd[2750]: wlp5s0: no IPv6 Routers available
dhcpcd[2750]: wlp5s0: carrier lost
dhcpcd[2750]: wlp5s0: carrier acquired
dhcpcd[2750]: wlp5s0: IAID 00:8b:d5:90
dhcpcd[2750]: wlp5s0: soliciting an IPv6 router
dhcpcd[2750]: wlp5s0: soliciting a DHCP lease
dhcpcd[2750]: wlp5s0: no IPv6 Routers available
dhcpcd[2750]: timed out
dhcpcd[2750]: allowing 8 seconds for IPv4LL timeout
dhcpcd[2750]: timed out
dhcpcd[2750]: exited

Back to top
View user's profile Send private message
Display posts from previous:   
Reply to topic    Gentoo Forums Forum Index Networking & Security All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum