| View previous topic :: View next topic |
| Author |
Message |
stefanbaptist
n00b
Joined: 15 Jun 2013
Posts: 2
|
 Posted: Sat Jun 15, 2013 9:26 pm Post subject: Problems with X11 (startx) on Macbook 4.1 (early 2008) |
 |
|
Hello, I just managed to install Gentoo. Yay. That's the good news.
But, the bad news is about X11.
Namely, when I run startx I run into some errors (i.e. no screens are found)
To be more precise, here is my dmesg and Xorg.log:
DMESG:
| Quote: | [ 1.387764] brd: module loaded
[ 1.389954] loop: module loaded
[ 1.390520] i8042: PNP: No PS/2 controller found. Probing ports directly.
[ 2.461447] i8042: No controller found
[ 2.461514] tsc: Refined TSC clocksource calibration: 2393.999 MHz
[ 2.461575] Switching to clocksource tsc
[ 2.461682] mousedev: PS/2 mouse device common for all mice
[ 2.461893] cpuidle: using governor ladder
[ 2.461931] cpuidle: using governor menu
[ 2.462275] TCP: cubic registered
[ 2.462306] NET: Registered protocol family 17
[ 2.462970] registered taskstats version 1
[ 2.466079] Freeing unused kernel memory: 524k freed
[ 2.609967] ACPI: bus type scsi registered
[ 2.610560] libata version 3.00 loaded.
[ 4.194022] ahci 0000:00:1f.2: version 3.0
[ 4.194163] ahci 0000:00:1f.2: irq 43 for MSI/MSI-X
[ 4.194275] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 1.5 Gbps 0x1 impl SATA mode
[ 4.194282] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ccc ems
[ 4.194293] ahci 0000:00:1f.2: setting latency timer to 64
[ 4.196234] scsi0 : ahci
[ 4.196690] scsi1 : ahci
[ 4.196995] scsi2 : ahci
[ 4.197307] ata1: SATA max UDMA/133 abar m2048@0x90704000 port 0x90704100 irq 43
[ 4.197310] ata2: DUMMY
[ 4.197312] ata3: DUMMY
[ 4.540036] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 4.541013] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 4.541374] ata1.00: ATA-8: Hitachi HTS542516K9SA00, BBCAC3GP, max UDMA/133
[ 4.541378] ata1.00: 312581808 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
[ 4.542484] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 4.542844] ata1.00: configured for UDMA/133
[ 4.543011] scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54251 BBCA PQ: 0 ANSI: 5
[ 4.543504] sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[ 4.543577] sd 0:0:0:0: [sda] Write Protect is off
[ 4.543582] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.543614] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.594078] sda: sda1 sda2 sda3 sda4 sda5
[ 4.595562] sd 0:0:0:0: [sda] Attached SCSI disk
[ 4.681915] ata_piix 0000:00:1f.1: version 2.13
[ 4.681932] ata_piix 0000:00:1f.1: power state changed by ACPI to D0
[ 4.682008] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 4.683562] scsi3 : ata_piix
[ 4.684344] scsi4 : ata_piix
[ 4.684640] ata4: PATA max UDMA/100 cmd 0x6108 ctl 0x6124 bmdma 0x60e0 irq 21
[ 4.684643] ata5: PATA max UDMA/100 cmd 0x6100 ctl 0x6120 bmdma 0x60e8 irq 21
[ 4.870737] ata4.00: ATAPI: MATSHITADVD-R UJ-867, HB01, max UDMA/66
[ 4.910510] ata4.00: configured for UDMA/66
[ 4.916029] scsi 3:0:0:0: CD-ROM MATSHITA DVD-R UJ-867 HB01 PQ: 0 ANSI: 5
[ 4.918609] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[ 4.918612] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 4.918920] sr 3:0:0:0: Attached scsi CD-ROM sr0
[ 5.106779] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 5.107022] sr 3:0:0:0: Attached scsi generic sg1 type 5
[ 5.474698] scsi: <fdomain> Detection failed (no card)
[ 5.566266] GDT-HA: Storage RAID Controller Driver. Version: 3.05
[ 5.769654] imm: Version 2.05 (for Linux 2.4.0)
[ 6.090497] Fusion MPT base driver 3.04.20
[ 6.090500] Copyright (c) 1999-2008 LSI Corporation
[ 6.204112] Fusion MPT SPI Host driver 3.04.20
[ 6.286541] Fusion MPT FC Host driver 3.04.20
[ 6.357440] Fusion MPT SAS Host driver 3.04.20
[ 6.412085] 3ware Storage Controller device driver for Linux v1.26.02.003.
[ 6.467485] 3ware 9000 Storage Controller device driver for Linux v2.26.02.014.
[ 6.523332] Compaq SMART2 Driver (v 2.6.0)
[ 6.624786] HP CISS Driver (v 3.6.26)
[ 6.800306] Adaptec aacraid driver 1.2-0[29801]-ms
[ 6.927225] megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
[ 6.929452] megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
[ 7.046470] megasas: 06.504.01.00-rc1 Mon. Oct. 1 17:00:00 PDT 2012
[ 7.113577] qla2xxx [0000:00:00.0]-0005: : QLogic Fibre Channel HBA Driver: 8.04.00.08-k.
[ 7.181639] Emulex LightPulse Fibre Channel SCSI driver 8.3.36
[ 7.181643] Copyright(c) 2004-2009 Emulex. All rights reserved.
[ 7.324144] aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded
[ 7.416585] ACPI: bus type usb registered
[ 7.416929] usbcore: registered new interface driver usbfs
[ 7.417265] usbcore: registered new interface driver hub
[ 7.417382] usbcore: registered new device driver usb
[ 7.420747] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 7.499146] Initializing USB Mass Storage driver...
[ 7.499233] usbcore: registered new interface driver usb-storage
[ 7.499235] USB Mass Storage support registered.
[ 7.566598] uhci_hcd: USB Universal Host Controller Interface driver
[ 7.566671] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 7.566679] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 7.566691] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 7.566763] uhci_hcd 0000:00:1a.0: irq 20, io base 0x000060c0
[ 7.566828] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 7.566833] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.566837] usb usb1: Product: UHCI Host Controller
[ 7.566840] usb usb1: Manufacturer: Linux 3.8.13-gentoo uhci_hcd
[ 7.566844] usb usb1: SerialNumber: 0000:00:1a.0
[ 7.567195] hub 1-0:1.0: USB hub found
[ 7.567203] hub 1-0:1.0: 2 ports detected
[ 7.567439] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 7.567447] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 7.567457] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
[ 7.567516] uhci_hcd 0000:00:1a.1: irq 16, io base 0x000060a0
[ 7.567577] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 7.567582] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.567585] usb usb2: Product: UHCI Host Controller
[ 7.567589] usb usb2: Manufacturer: Linux 3.8.13-gentoo uhci_hcd
[ 7.567592] usb usb2: SerialNumber: 0000:00:1a.1
[ 7.567982] hub 2-0:1.0: USB hub found
[ 7.567992] hub 2-0:1.0: 2 ports detected
[ 7.568185] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 7.568192] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 7.568203] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 3
[ 7.568247] uhci_hcd 0000:00:1d.0: irq 16, io base 0x00006080
[ 7.568306] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 7.568310] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.568314] usb usb3: Product: UHCI Host Controller
[ 7.568317] usb usb3: Manufacturer: Linux 3.8.13-gentoo uhci_hcd
[ 7.568321] usb usb3: SerialNumber: 0000:00:1d.0
[ 7.568757] hub 3-0:1.0: USB hub found
[ 7.568765] hub 3-0:1.0: 2 ports detected
[ 7.568955] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 7.568963] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 7.568973] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 4
[ 7.569035] uhci_hcd 0000:00:1d.1: irq 18, io base 0x00006060
[ 7.569099] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 7.569103] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.569107] usb usb4: Product: UHCI Host Controller
[ 7.569111] usb usb4: Manufacturer: Linux 3.8.13-gentoo uhci_hcd
[ 7.569114] usb usb4: SerialNumber: 0000:00:1d.1
[ 7.569555] hub 4-0:1.0: USB hub found
[ 7.569562] hub 4-0:1.0: 2 ports detected
[ 7.569757] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 7.569764] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 7.569775] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 5
[ 7.569819] uhci_hcd 0000:00:1d.2: irq 21, io base 0x00006040
[ 7.569878] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 7.569882] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.569886] usb usb5: Product: UHCI Host Controller
[ 7.569889] usb usb5: Manufacturer: Linux 3.8.13-gentoo uhci_hcd
[ 7.569893] usb usb5: SerialNumber: 0000:00:1d.2
[ 7.570402] hub 5-0:1.0: USB hub found
[ 7.570410] hub 5-0:1.0: 2 ports detected
[ 7.639894] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 7.712375] usbcore: registered new interface driver usbhid
[ 7.712378] usbhid: USB HID core driver
[ 7.880038] usb 1-1: new full-speed USB device number 2 using uhci_hcd
[ 8.060826] usb 1-1: New USB device found, idVendor=05ac, idProduct=1000
[ 8.060831] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 8.082704] input: HID 05ac:1000 as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1:1.0/input/input0
[ 8.083578] hid-generic 0003:05AC:1000.0001: input,hidraw0: USB HID v1.11 Keyboard [HID 05ac:1000] on usb-0000:00:1a.0-1/input0
[ 8.114695] input: HID 05ac:1000 as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1:1.1/input/input1
[ 8.115649] hid-generic 0003:05AC:1000.0002: input,hidraw1: USB HID v1.11 Mouse [HID 05ac:1000] on usb-0000:00:1a.0-1/input1
[ 8.230050] usb 1-2: new full-speed USB device number 3 using uhci_hcd
[ 8.405825] usb 1-2: New USB device found, idVendor=13fe, idProduct=1f00
[ 8.405830] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 8.405834] usb 1-2: Product: DataTraveler 2.0
[ 8.405838] usb 1-2: Manufacturer: Kingston
[ 8.405841] usb 1-2: SerialNumber: 5B820C003557
[ 8.409047] scsi5 : usb-storage 1-2:1.0
[ 8.520072] usb 4-2: new full-speed USB device number 2 using uhci_hcd
[ 8.690106] usb 4-2: New USB device found, idVendor=05ac, idProduct=8501
[ 8.690111] usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 8.690115] usb 4-2: Product: Built-in iSight
[ 8.690119] usb 4-2: Manufacturer: Micron
[ 8.810026] usb 5-1: new low-speed USB device number 2 using uhci_hcd
[ 8.977705] device-mapper: uevent: version 1.0.3
[ 8.977851] device-mapper: ioctl: 4.23.1-ioctl (2012-12-1 initialised: dm-devel@redhat.com
[ 8.991887] usb 5-1: New USB device found, idVendor=05ac, idProduct=8242
[ 8.991892] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 8.991896] usb 5-1: Product: IR Receiver
[ 8.991900] usb 5-1: Manufacturer: Apple Computer, Inc.
[ 9.026841] apple 0003:05AC:8242.0003: hiddev0,hidraw2: USB HID v1.11 Device [Apple Computer, Inc. IR Receiver] on usb-0000:00:1d.2-1/input0
[ 9.140026] usb 5-2: new full-speed USB device number 3 using uhci_hcd
[ 9.329887] usb 5-2: New USB device found, idVendor=05ac, idProduct=0229
[ 9.329892] usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 9.329896] usb 5-2: Product: Apple Internal Keyboard / Trackpad
[ 9.329900] usb 5-2: Manufacturer: Apple Computer
[ 9.340507] input: Apple Computer Apple Internal Keyboard / Trackpad as /devices/pci0000:00/0000:00:1d.2/usb5/5-2/5-2:1.0/input/input2
[ 9.341157] apple 0003:05AC:0229.0004: input,hidraw3: USB HID v1.11 Keyboard [Apple Computer Apple Internal Keyboard / Trackpad] on usb-0000:00:1d.2-2/input0
[ 9.349029] input: Apple Computer Apple Internal Keyboard / Trackpad as /devices/pci0000:00/0000:00:1d.2/usb5/5-2/5-2:1.2/input/input3
[ 9.349574] apple 0003:05AC:0229.0005: input,hidraw4: USB HID v1.11 Device [Apple Computer Apple Internal Keyboard / Trackpad] on usb-0000:00:1d.2-2/input2
[ 9.404859] scsi 5:0:0:0: Direct-Access Kingston DataTraveler 2.0 PMAP PQ: 0 ANSI: 0 CCS
[ 9.406601] sd 5:0:0:0: Attached scsi generic sg2 type 0
[ 9.410837] sd 5:0:0:0: [sdb] 1970176 512-byte logical blocks: (1.00 GB/962 MiB)
[ 9.413832] sd 5:0:0:0: [sdb] Write Protect is off
[ 9.413838] sd 5:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 9.416832] sd 5:0:0:0: [sdb] No Caching mode page present
[ 9.416836] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[ 9.434839] sd 5:0:0:0: [sdb] No Caching mode page present
[ 9.434843] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[ 9.440846] sdb: sdb1
[ 9.453839] sd 5:0:0:0: [sdb] No Caching mode page present
[ 9.453844] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[ 9.453848] sd 5:0:0:0: [sdb] Attached SCSI removable disk
[ 9.555414] md: raid0 personality registered for level 0
[ 9.631837] md: raid1 personality registered for level 1
[ 9.734106] async_tx: api initialized (async)
[ 9.910030] raid6: sse2x1 2153 MB/s
[ 10.080021] raid6: sse2x2 2435 MB/s
[ 10.250013] raid6: sse2x4 3548 MB/s
[ 10.250016] raid6: using algorithm sse2x4 (3548 MB/s)
[ 10.250018] raid6: using ssse3x2 recovery algorithm
[ 10.298265] xor: automatically using best checksumming function:
[ 10.390005] generic_sse: 4511.600 MB/sec
[ 10.407082] md: raid6 personality registered for level 6
[ 10.407085] md: raid5 personality registered for level 5
[ 10.407087] md: raid4 personality registered for level 4
[ 10.493717] md: raid10 personality registered for level 10
[ 10.574506] md: linear personality registered for level -1
[ 10.655264] md: multipath personality registered for level -4
[ 10.764091] Btrfs loaded
[ 10.852844] JFS: nTxBlock = 8192, nTxLock = 65536
[ 10.970555] RPC: Registered named UNIX socket transport module.
[ 10.970559] RPC: Registered udp transport module.
[ 10.970561] RPC: Registered tcp transport module.
[ 10.970563] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 11.075910] fuse init (API version 7.20)
[ 11.162631] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
[ 11.162634] e1000: Copyright (c) 1999-2006 Intel Corporation.
[ 11.269706] pps_core: LinuxPPS API ver. 1 registered
[ 11.269710] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 11.272033] PTP clock support registered
[ 11.379560] Loading iSCSI transport class v2.0-870.
[ 22.836485] UDF-fs: warning (device sda3): udf_fill_super: No partition found (1)
[ 22.852927] (mount,16855,1):ocfs2_fill_super:1039 ERROR: superblock probe failed!
[ 22.852931] (mount,16855,1):ocfs2_fill_super:1230 ERROR: status = -22
[ 22.853269] GFS2: gfs2 mount does not exist
[ 22.853463] device fsid c7237423-75b6-4af5-97aa-e485dcadf65d devid 1 transid 613 /dev/sda3
[ 22.854083] btrfs: disk space caching is enabled
[ 25.217330] systemd-udevd[16991]: starting version 200
[ 25.742237] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input4
[ 25.742458] ACPI: Lid Switch [LID0]
[ 25.742556] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input5
[ 25.742769] ACPI: Power Button [PWRB]
[ 25.742861] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input6
[ 25.742921] ACPI: Sleep Button [SLPB]
[ 25.743050] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input7
[ 25.743109] ACPI: Power Button [PWRF]
[ 25.750399] ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
[ 25.750478] ACPI: AC Adapter [ADP1] (on-line)
[ 25.752941] agpgart-intel 0000:00:00.0: Intel 965GM Chipset
[ 25.753333] agpgart-intel 0000:00:00.0: detected gtt size: 524288K total, 262144K mappable
[ 25.754983] agpgart-intel 0000:00:00.0: detected 16384K stolen memory
[ 25.755269] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0x80000000
[ 25.755622] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
[ 25.755635] ACPI: Battery Slot [BAT0] (battery absent)
[ 25.766041] ehci-pci: EHCI PCI platform driver
[ 25.766125] ehci-pci 0000:00:1a.7: setting latency timer to 64
[ 25.766132] ehci-pci 0000:00:1a.7: EHCI Host Controller
[ 25.766145] ehci-pci 0000:00:1a.7: new USB bus registered, assigned bus number 6
[ 25.766179] ehci-pci 0000:00:1a.7: debug port 1
[ 25.770122] ehci-pci 0000:00:1a.7: cache line size of 64 is not supported
[ 25.770136] ehci-pci 0000:00:1a.7: irq 21, io mem 0x90704c00
[ 25.790076] ehci-pci 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[ 25.790105] usb 1-1: USB disconnect, device number 2
[ 25.790161] usb usb6: New USB device found, idVendor=1d6b, idProduct=0002
[ 25.790165] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 25.790169] usb usb6: Product: EHCI Host Controller
[ 25.790173] usb usb6: Manufacturer: Linux 3.8.13-gentoo ehci_hcd
[ 25.790176] usb usb6: SerialNumber: 0000:00:1a.7
[ 25.790444] hub 6-0:1.0: USB hub found
[ 25.790451] hub 6-0:1.0: 4 ports detected
[ 25.790751] ehci-pci 0000:00:1d.7: setting latency timer to 64
[ 25.790758] ehci-pci 0000:00:1d.7: EHCI Host Controller
[ 25.790769] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 7
[ 25.790802] ehci-pci 0000:00:1d.7: debug port 1
[ 25.794739] ehci-pci 0000:00:1d.7: cache line size of 64 is not supported
[ 25.794750] ehci-pci 0000:00:1d.7: irq 20, io mem 0x90704800
[ 25.844629] ACPI: Requesting acpi_cpufreq
[ 25.856895] appletouch 5-2:1.1: Failed to read mode from device.
[ 25.856907] appletouch: probe of 5-2:1.1 failed with error -5
[ 25.856935] usbcore: registered new interface driver appletouch
[ 25.870019] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 25.870078] usb usb7: New USB device found, idVendor=1d6b, idProduct=0002
[ 25.870083] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 25.870087] usb usb7: Product: EHCI Host Controller
[ 25.870090] usb usb7: Manufacturer: Linux 3.8.13-gentoo ehci_hcd
[ 25.870094] usb usb7: SerialNumber: 0000:00:1d.7
[ 25.870337] hub 7-0:1.0: USB hub found
[ 25.870346] hub 7-0:1.0: 6 ports detected
[ 25.881432] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 25.881526] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input8
[ 25.890110] b43-pci-bridge 0000:02:00.0: enabling device (0000 -> 0002)
[ 25.896435] sky2: driver version 1.30
[ 25.896492] sky2 0000:03:00.0: enabling device (0000 -> 0003)
[ 25.896639] sky2 0000:03:00.0: Yukon-2 EC Ultra chip revision 3
[ 25.897160] sky2 0000:03:00.0: irq 44 for MSI/MSI-X
[ 25.897804] sky2 0000:03:00.0 eth0: addr 00:22:41:21:43:0c
[ 25.930076] ssb: Found chip with id 0x4321, rev 0x03 and package 0x00
[ 25.930088] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x13, vendor 0x4243)
[ 25.930099] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x0C, vendor 0x4243)
[ 25.930109] ssb: Core 2 found: PCI-E (cc 0x820, rev 0x04, vendor 0x4243)
[ 25.930119] ssb: Core 3 found: PCI (cc 0x804, rev 0x0D, vendor 0x4243)
[ 25.930130] ssb: Core 4 found: USB 1.1 Host (cc 0x817, rev 0x04, vendor 0x4243)
[ 25.981203] microcode: CPU0 sig=0x10676, pf=0x80, revision=0x60c
[ 26.031695] Monitor-Mwait will be used to enter C-1 state
[ 26.031869] Monitor-Mwait will be used to enter C-2 state
[ 26.031877] Monitor-Mwait will be used to enter C-3 state
[ 26.031883] tsc: Marking TSC unstable due to TSC halts in idle
[ 26.031899] ACPI: acpi_idle registered with cpuidle
[ 26.032325] Switching to clocksource hpet
[ 26.050311] sdb: detected capacity change from 1008730112 to 0
[ 26.050351] ssb: Sonics Silicon Backplane found on PCI device 0000:02:00.0
[ 26.053744] input: PC Speaker as /devices/platform/pcspkr/input/input9
[ 26.065410] microcode: CPU1 sig=0x10676, pf=0x80, revision=0x60c
[ 26.068248] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 26.090511] systemd-udevd[17007]: renamed network interface eth0 to enp3s0
[ 26.224652] snd_hda_intel 0000:00:1b.0: enabling device (0000 -> 0002)
[ 26.224755] snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X
[ 26.230052] usb 1-2: USB disconnect, device number 3
[ 26.240040] scsi 5:0:0:0: rejecting I/O to offline device
[ 26.240044] scsi 5:0:0:0: killing request
[ 26.249950] hda_codec: ALC889A: SKU not ready 0x400000f0
[ 26.400745] i801_smbus 0000:00:1f.3: enabling device (0000 -> 0003)
[ 26.400757] ACPI Warning: 0x000000000000efa0-0x000000000000efbf SystemIO conflicts with Region \_SB_.PCI0.SBUS.SMBI 1 (20121018/utaddress-251)
[ 26.400766] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 26.425376] cfg80211: Calling CRDA to update world regulatory domain
[ 26.500051] usb 6-2: new high-speed USB device number 3 using ehci-pci
[ 26.594262] applesmc: key=220 fan=1 temp=10 index=10 acc=1 lux=0 kbd=0
[ 26.618486] input: applesmc as /devices/platform/applesmc.768/input/input10
[ 26.658821] usb 6-2: New USB device found, idVendor=13fe, idProduct=1f00
[ 26.658827] usb 6-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 26.658831] usb 6-2: Product: DataTraveler 2.0
[ 26.658835] usb 6-2: Manufacturer: Kingston
[ 26.658838] usb 6-2: SerialNumber: 5B820C003557
[ 26.659281] scsi6 : usb-storage 6-2:1.0
[ 26.659507] usb 4-2: USB disconnect, device number 2
[ 26.778705] b43-phy0: Broadcom 4321 WLAN found (core revision 12)
[ 26.820075] usb 5-1: USB disconnect, device number 2
[ 26.870036] b43-phy0 ERROR: FOUND UNSUPPORTED PHY (Analog 5, Type 4 (N), Revision 2)
[ 26.870061] b43: probe of ssb0:0 failed with error -95
[ 26.870086] Broadcom 43xx driver loaded [ Features: PML ]
[ 26.980063] usb 5-2: USB disconnect, device number 3
[ 27.206924] device fsid c7237423-75b6-4af5-97aa-e485dcadf65d devid 1 transid 613 /dev/sda3
[ 27.651614] scsi 6:0:0:0: Direct-Access Kingston DataTraveler 2.0 PMAP PQ: 0 ANSI: 0 CCS
[ 27.653827] sd 6:0:0:0: Attached scsi generic sg2 type 0
[ 27.653950] sd 6:0:0:0: [sdb] 1970176 512-byte logical blocks: (1.00 GB/962 MiB)
[ 27.654760] sd 6:0:0:0: [sdb] Write Protect is off
[ 27.654766] sd 6:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 27.655467] sd 6:0:0:0: [sdb] No Caching mode page present
[ 27.655471] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 27.658828] sd 6:0:0:0: [sdb] No Caching mode page present
[ 27.658833] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 27.660102] sdb: sdb1
[ 27.665720] sd 6:0:0:0: [sdb] No Caching mode page present
[ 27.665725] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 27.665729] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[ 27.670085] usb 7-4: new high-speed USB device number 2 using ehci-pci
[ 27.830826] usb 7-4: New USB device found, idVendor=05ac, idProduct=8501
[ 27.830832] usb 7-4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 27.830836] usb 7-4: Product: Built-in iSight
[ 27.830839] usb 7-4: Manufacturer: Micron
[ 28.300046] usb 1-1: new full-speed USB device number 4 using uhci_hcd
[ 28.489082] usb 1-1: New USB device found, idVendor=05ac, idProduct=1000
[ 28.489088] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 28.509922] btrfs: disk space caching is enabled
[ 28.510619] input: HID 05ac:1000 as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1:1.0/input/input11
[ 28.510774] hid-generic 0003:05AC:1000.0006: input,hidraw0: USB HID v1.11 Keyboard [HID 05ac:1000] on usb-0000:00:1a.0-1/input0
[ 28.542622] input: HID 05ac:1000 as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1:1.1/input/input12
[ 28.543002] hid-generic 0003:05AC:1000.0007: input,hidraw1: USB HID v1.11 Mouse [HID 05ac:1000] on usb-0000:00:1a.0-1/input1
[ 29.050093] usb 5-1: new low-speed USB device number 4 using uhci_hcd
[ 29.233117] usb 5-1: New USB device found, idVendor=05ac, idProduct=8242
[ 29.233123] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 29.233127] usb 5-1: Product: IR Receiver
[ 29.233130] usb 5-1: Manufacturer: Apple Computer, Inc.
[ 29.267574] apple 0003:05AC:8242.0008: hiddev0,hidraw2: USB HID v1.11 Device [Apple Computer, Inc. IR Receiver] on usb-0000:00:1d.2-1/input0
[ 29.600051] usb 5-2: new full-speed USB device number 5 using uhci_hcd
[ 29.796117] usb 5-2: New USB device found, idVendor=05ac, idProduct=0229
[ 29.796123] usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 29.796127] usb 5-2: Product: Apple Internal Keyboard / Trackpad
[ 29.796130] usb 5-2: Manufacturer: Apple Computer
[ 29.805579] input: Apple Computer Apple Internal Keyboard / Trackpad as /devices/pci0000:00/0000:00:1d.2/usb5/5-2/5-2:1.0/input/input13
[ 29.805724] apple 0003:05AC:0229.0009: input,hidraw3: USB HID v1.11 Keyboard [Apple Computer Apple Internal Keyboard / Trackpad] on usb-0000:00:1d.2-2/input0
[ 29.810109] appletouch 5-2:1.1: Geyser mode initialized.
[ 29.810198] input: appletouch as /devices/pci0000:00/0000:00:1d.2/usb5/5-2/5-2:1.1/input/input14
[ 29.816213] input: Apple Computer Apple Internal Keyboard / Trackpad as /devices/pci0000:00/0000:00:1d.2/usb5/5-2/5-2:1.2/input/input15
[ 29.816357] apple 0003:05AC:0229.000A: input,hidraw4: USB HID v1.11 Device [Apple Computer Apple Internal Keyboard / Trackpad] on usb-0000:00:1d.2-2/input2
[ 30.722296] sky2 0000:03:00.0 enp3s0: enabling interface
|
Xorg.log:
| Quote: | [ 43.053]
X.Org X Server 1.13.4
Release Date: 2013-04-17
[ 43.053] X Protocol Version 11, Revision 0
[ 43.053] Build Operating System: Linux 3.8.13-gentoo x86_64 Gentoo
[ 43.053] Current Operating System: Linux tux 3.8.13-gentoo #1 SMP Sat Jun 15 03:01:49 CEST 2013 x86_64
[ 43.053] Kernel command line: BOOT_IMAGE=/kernel-genkernel-x86_64-3.8.13-gentoo root=UUID=c7237423-75b6-4af5-97aa-e485dcadf65d ro i915.modeset=1
[ 43.054] Build Date: 15 June 2013 10:05:31PM
[ 43.054]
[ 43.054] Current version of pixman: 0.28.0 to make sure that you have the latest version.
[ 43.054] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 43.054] (==) Log file: "/var/log/Xorg.0.log", Time: Sat Jun 15 22:38:08 2013
[ 43.077] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[ 43.077] (==) No Layout section. Using the first Screen section.
[ 43.077] (==) No screen section available. Using defaults.
[ 43.077] (**) |-->Screen "Default Screen Section" (0)
[ 43.077] (**) | |-->Monitor "<default monitor>"
[ 43.077] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 43.077] (==) Automatically adding devices
[ 43.077] (==) Automatically enabling devices
[ 43.077] (==) Automatically adding GPU devices
[ 43.122] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/misc/".
[ 43.122] Entry deleted from font path.
[ 43.122] (Run 'mkfontdir' on "/usr/share/fonts/misc/").
[ 43.122] (WW) The directory "/usr/share/fonts/TTF/" does not exist.
[ 43.122] Entry deleted from font path.
[ 43.122] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 43.122] Entry deleted from font path.
[ 43.122] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[ 43.122] Entry deleted from font path.
[ 43.122] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 43.122] Entry deleted from font path.
[ 43.122] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 43.122] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 43.122] Entry deleted from font path.
[ 43.122] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 43.122] (==) FontPath set to:
[ 43.122] (==) ModulePath set to "/usr/lib64/xorg/modules"
[ 43.122] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 43.122] (II) Loader magic: 0x809be0
[ 43.122] (II) Module ABI versions:
[ 43.122] X.Org ANSI C Emulation: 0.4
[ 43.122] X.Org Video Driver: 13.1
[ 43.122] X.Org XInput driver : 18.0
[ 43.122] X.Org Server Extension : 7.0
[ 43.123] (II) config/udev: Adding drm device (/dev/dri/card0)
[ 43.126] (--) PCI:*(0:0:2:0) 8086:2a02:106b:00a1 rev 3, Mem @ 0x90100000/1048576, 0x80000000/268435456, I/O @ 0x00006110/8
[ 43.126] (--) PCI: (0:0:2:1) 8086:2a03:106b:00a1 rev 3, Mem @ 0x90200000/1048576
[ 43.126] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 43.126] Initializing built-in extension Generic Event Extension
[ 43.126] Initializing built-in extension SHAPE
[ 43.126] Initializing built-in extension MIT-SHM
[ 43.127] Initializing built-in extension XInputExtension
[ 43.127] Initializing built-in extension XTEST
[ 43.127] Initializing built-in extension BIG-REQUESTS
[ 43.127] Initializing built-in extension SYNC
[ 43.127] Initializing built-in extension XKEYBOARD
[ 43.127] Initializing built-in extension XC-MISC
[ 43.127] Initializing built-in extension XINERAMA
[ 43.127] Initializing built-in extension XFIXES
[ 43.127] Initializing built-in extension RENDER
[ 43.127] Initializing built-in extension RANDR
[ 43.127] Initializing built-in extension COMPOSITE
[ 43.127] Initializing built-in extension DAMAGE
[ 43.127] Initializing built-in extension MIT-SCREEN-SAVER
[ 43.128] Initializing built-in extension DOUBLE-BUFFER
[ 43.128] Initializing built-in extension RECORD
[ 43.128] Initializing built-in extension DPMS
[ 43.128] Initializing built-in extension X-Resource
[ 43.128] Initializing built-in extension XVideo
[ 43.130] Initializing built-in extension XVideo-MotionCompensation
[ 43.131] Initializing built-in extension XFree86-VidModeExtension
[ 43.133] Initializing built-in extension XFree86-DGA
[ 43.135] Initializing built-in extension XFree86-DRI
[ 43.136] Initializing built-in extension DRI2
[ 43.136] (II) LoadModule: "glx"
[ 43.160] (II) Loading /usr/lib64/xorg/modules/extensions/libglx.so
[ 43.183] (II) Module glx: vendor="X.Org Foundation"
[ 43.183] compiled for 1.13.4, module version = 1.0.0
[ 43.183] ABI class: X.Org Server Extension, version 7.0
[ 43.184] (==) AIGLX enabled
[ 43.185] Loading extension GLX
[ 43.185] (==) Matched intel as autoconfigured driver 0
[ 43.185] (==) Matched intel as autoconfigured driver 1
[ 43.185] (==) Matched vesa as autoconfigured driver 2
[ 43.185] (==) Matched modesetting as autoconfigured driver 3
[ 43.185] (==) Matched fbdev as autoconfigured driver 4
[ 43.185] (==) Assigned the driver to the xf86ConfigLayout
[ 43.185] (II) LoadModule: "intel"
[ 43.198] (WW) Warning, couldn't open module intel
[ 43.198] (II) UnloadModule: "intel"
[ 43.198] (II) Unloading intel
[ 43.198] (EE) Failed to load module "intel" (module does not exist, 0)
[ 43.198] (II) LoadModule: "vesa"
[ 43.199] (WW) Warning, couldn't open module vesa
[ 43.199] (II) UnloadModule: "vesa"
[ 43.199] (II) Unloading vesa
[ 43.199] (EE) Failed to load module "vesa" (module does not exist, 0)
[ 43.199] (II) LoadModule: "modesetting"
[ 43.199] (WW) Warning, couldn't open module modesetting
[ 43.199] (II) UnloadModule: "modesetting"
[ 43.199] (II) Unloading modesetting
[ 43.199] (EE) Failed to load module "modesetting" (module does not exist, 0)
[ 43.199] (II) LoadModule: "fbdev"
[ 43.200] (WW) Warning, couldn't open module fbdev
[ 43.200] (II) UnloadModule: "fbdev"
[ 43.200] (II) Unloading fbdev
[ 43.200] (EE) Failed to load module "fbdev" (module does not exist, 0)
[ 43.200] (EE) No drivers available.
[ 43.203]
Fatal server error:
[ 43.203] no screens found
[ 43.205] (EE)
Please consult the The X.Org Foundation support
at http://wiki.x.org
for help.
[ 43.211] (EE) Please also check the log file at "/var/log/Xorg.0.log" for additional information.
[ 43.213] (EE)
|
*As for the kernel, I used genkernel.
P.S. I think I might have both mdev and udev. Is that possible & okay?
Thanks in advance. |
|
| Back to top |
|
 |
eccerr0r
Watchman
Joined: 01 Jul 2004
Posts: 9679
Location: almost Mile High in the USA
|
| Posted: Sat Jun 15, 2013 10:19 pm Post subject: |
|
|
do you have VIDEO_CARDS=intel in your make.conf? Then it should build xf86-video-intel, and not give the module not found error?
_________________
Intel Core i7 2700K/Radeon R7 250/24GB DDR3/256GB SSD
What am I supposed watching? |
|
| Back to top |
|
|
stefanbaptist
n00b
Joined: 15 Jun 2013
Posts: 2
|
| Posted: Sat Jun 15, 2013 10:23 pm Post subject: |
|
|
| eccerr0r wrote: | | do you have VIDEO_CARDS=intel in your make.conf? Then it should build xf86-video-intel, and not give the module not found error? |
What I actually have is i915. I'm gonna try changing it and rebuilding. Will report the results. Thanks |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Desktop Environments
