View previous topic :: View next topic |
Author |
Message |
Yczo Apprentice
Joined: 09 Jul 2011 Posts: 225
|
Posted: Tue May 14, 2013 5:39 pm Post subject: udev-200 problema tras actualizar ¿Bien resuelto? |
|
|
Hola chicos, tras un periodo de mucho curro, ayer me lié a actualizar la distro.
El caso que tras seguir la wiki http://wiki.gentoo.org/wiki/Udev/upgrade, y borrar las reglas 70 y 80, al reiniciar, me encuentro con que el sistema de arranque se queda en udev bloquedo durante 1 minuto o así declarando 'Waiting for uevents to be processed ...'.
Tras mirar /var/log/messages, me encuentro con que el interfaz de red se remobra desde eth0 a enp9s0, justo e mismo problema que el de este chico https://forums.gentoo.org/viewtopic-t-957608.html, solo que a el le funciona la solución y a mi no. Mire en /etc/conf.d/iptables como sugiere el Admin, pero ninguna referencia eth0.
Vamos que no tengo ni pajolera idea de que hacer.
Code: |
Aquí os muestro los servicios que arranco
NetworkManager | default
alsasound | boot
bootmisc | boot
consolefont | boot
consolekit | default
cupsd | default
dbus | default
devfs | sysinit
dmesg | sysinit
fsck | boot
gpm | default
hostname | boot
hwclock | boot
keymaps | boot
killprocs | shutdown
laptop_mode | default
local | default
localmount | boot
modules | boot
mount-ro | shutdown
mtab | boot
net.enp9s0 | default
net.lo | boot
netmount | default
procfs | boot
root | boot
savecache | shutdown
swapfiles | boot
sysctl | boot
sysfs | sysinit
syslog-ng | default
termencoding | boot
tmpfiles.setup | boot
udev | sysinit
udev-mount | sysinit
urandom | boot
vixie-cron | default
xdm | default
|
Si alguien sabe algo al respecto, por favor que no se prive de hacerlo jeejej
Un saludo y gracias de antemano
Last edited by Yczo on Tue May 14, 2013 10:53 pm; edited 1 time in total |
|
Back to top |
|
|
quilosaq Veteran
Joined: 22 Dec 2009 Posts: 1521
|
Posted: Tue May 14, 2013 7:19 pm Post subject: |
|
|
https://forums.gentoo.org/viewtopic-t-957608.html
El 9 de "enp9s0" parece un poco raro. Comprueba que tienes esa interfaz:
Si la tienes, mira que dice:
Code: | # /etc/init.d/net.enp9so stop
# /etc/init.d/net.enp9so start |
|
|
Back to top |
|
|
Yczo Apprentice
Joined: 09 Jul 2011 Posts: 225
|
Posted: Tue May 14, 2013 7:26 pm Post subject: |
|
|
Si por suerte tengo red y parece que la interfaz funciona. De todas formas gracias quilosaq
ifconfig -a
enp9s0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet ---.--.--.-- netmask 255.255.255.0 broadcast ---.---.-.--- //borro las ip, por si alguien por internet es curioso xdd
inet6 fe80::f24d:a2ff:fe5a:6f0a prefixlen 64 scopeid 0x20<link>
ether f0:4d:a2:5a:6f:0a txqueuelen 1000 (Ethernet)
RX packets 703196 bytes 932779438 (889.5 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 507590 bytes 43072560 (41.0 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 |
|
Back to top |
|
|
Yczo Apprentice
Joined: 09 Jul 2011 Posts: 225
|
Posted: Tue May 14, 2013 10:47 pm Post subject: |
|
|
solucionado, ¿Pero es una buena solución?
Editando el archivo /etc/init.d/udev
ebegin "Waiting for uevents to be processed" <= Debajo de la sentencia se encuentra un timeout
udevadm settle --timeout=${udev_settle_timeout:-60} <= tan sencillo como cambiar el 60 por 0
Pero ¿Esta bien? ¿Puede dar problemas? |
|
Back to top |
|
|
|