Gentoo Forums
Gentoo Forums
Gentoo Forums
Quick Search: in
Laserdrucker einrichten/ kalibrieren
View unanswered posts
View posts from last 24 hours
View posts from last 7 days

 
Reply to topic    Gentoo Forums Forum Index Deutsches Forum (German)
View previous topic :: View next topic  
Author Message
flammenflitzer
Advocate
Advocate


Joined: 25 Nov 2003
Posts: 3463
Location: Berlin

PostPosted: Sat May 18, 2013 7:07 am    Post subject: Laserdrucker einrichten/ kalibrieren Reply with quote

Hallo,
ich nutzte schon recht lange meinen Laserdrucker HP LaserJet 6L. Nach dem Kauf eines neuen Motherboard muß ich den Drucker über ein parallel zu usb Kabel nuzten. Allerdings ist die Druckqualität gesunken. bei Textdokumenten ist schwarz im Druck nur noch ein dunkles grau. Sollte ich foomatic ausprobieren? Kann ich den Drucker kalibrieren? Hat jemand eine Idee?
Ich habe auch
Code:
net-print/hplip-3.12.10a  USE="X hpcups kde libnotify libusb0 parport (policykit) qt4 -doc -fax -hpijs -minimal -scanner -snmp -static-ppds" 0 kB
ausprobiert, allerdings wird im hp-setup der Drucker auch bei manueller Eingabe nicht erkannt.
Ich denke, das es das Gerät ist:
Code:
flammenflitzer olaf # lsusb..
Bus 002 Device 003: ID 067b:2305 Prolific Technology, Inc. PL2305 Parallel Port

Code:
flammenflitzer olaf # dmesg | grep print
[    5.593031] usblp 2-1.6:1.0: usblp0: USB Bidirectional printer dev 3 if 0 alt 1 proto 2 vid 0x067B pid 0x2305
Code:

flammenflitzer olaf # dmesg | grep lp
[    0.000000] On node 0 totalpages: 1034582
[    0.000002] Calibrating delay loop (skipped), value calculated using timer frequency.. 5986.31 BogoMIPS (lpj=2993156)
[    0.187604] lp: driver loaded but no devices found
[    3.635588] lpc_ich: Resource conflict(s) found affecting gpio_ich
[    5.593031] usblp 2-1.6:1.0: usblp0: USB Bidirectional printer dev 3 if 0 alt 1 proto 2 vid 0x067B pid 0x2305
[    5.593053] usbcore: registered new interface driver usblp
Code:
flammenflitzer cups # cat /etc/cups/printers.conf
# Printer configuration file for CUPS v1.5.2
# Written by cupsd on 2013-04-12 19:59
# DO NOT EDIT THIS FILE WHEN CUPSD IS RUNNING
<DefaultPrinter LaserJet>
UUID urn:uuid:29d53789-2e07-3dde-7c74-ed529bc13d71
Info LaserJet
Location flammenflitzer
MakeModel HP LaserJet Series PCL 4/5
DeviceURI parallel:/dev/usb/lp0
State Idle
StateTime 1365789558
Type 8400964
Accepting Yes
Shared Yes
JobSheets none none
QuotaPeriod 0
PageLimit 0
KLimit 0
OpPolicy default
ErrorPolicy stop-printer
</Printer>
Back to top
View user's profile Send private message
demiurg
Tux's lil' helper
Tux's lil' helper


Joined: 26 Jul 2005
Posts: 108

PostPosted: Mon May 20, 2013 8:09 pm    Post subject: Laserdrucker einrichten/ kalibrieren Reply with quote

Quote:
Info LaserJet
Location flammenflitzer
MakeModel HP LaserJet Series PCL 4/5
DeviceURI parallel:/dev/usb/lp0
State Idle


finde ich schon etwas seltsam mit dem Anschluss parallel

bei mir
Code:
Info Kyocera FS-1010 lokal
MakeModel Kyocera Mita FS-1010
DeviceURI usb://Kyocera/FS-1010
State Idle


mit cups-1.5.2-r4 und deaktiviertem usb Flag, dafür usb Druckerunterstützung im Kernel eingebaut.

Gruß
_________________
Kernel 6.xx-gentoo
GCC 12.xx
Profile amd64/17.1/desktop/plasma/systemd/merged-usr
Ryzen 5950X
GA X570 PRO BIOS F35
ATI RX6800
Back to top
View user's profile Send private message
Display posts from previous:   
Reply to topic    Gentoo Forums Forum Index Deutsches Forum (German) All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum