| View previous topic :: View next topic |
| Author |
Message |
Berkz
Apprentice
Joined: 26 Aug 2002
Posts: 205
Location: Iceland
|
 Posted: Thu Oct 09, 2003 8:39 pm Post subject: Kernel 2.6 using all my cpu |
 |
|
khubd is using 100% of cpu power from start.
| Code: |
Linux version 2.6.0-test7 (root@localhost) (gcc version 3.2.3 20030422 (Gentoo Linux 1.4 3.2.3-r2, propolice)) #2 Thu Oct 9 20:26:20 GMT 2003
Video mode to be used for restore is f00
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000002fff0000 (usable)
BIOS-e820: 000000002fff0000 - 000000002fff3000 (ACPI NVS)
BIOS-e820: 000000002fff3000 - 0000000030000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
767MB LOWMEM available.
On node 0 totalpages: 196592
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 192496 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 AWARD ) @ 0x000f76d0
ACPI: RSDT (v001 AWARD AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x2fff3000
ACPI: FADT (v001 AWARD AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x2fff3040
ACPI: DSDT (v001 AWARD AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
Building zonelist for node : 0
Kernel command line: root=/dev/hda3
Initializing CPU#0
PID hash table entries: 4096 (order 12: 32768 bytes)
Detected 1395.209 MHz processor.
Console: colour VGA+ 80x25
Memory: 773868k/786368k available (2633k kernel code, 11708k reserved, 923k data, 132k init, 0k highmem)
Calibrating delay loop... 2744.32 BogoMIPS
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0183f9ff c1c7f9ff 00000000 00000000
CPU: After vendor identify, caps: 0183f9ff c1c7f9ff 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0183f9ff c1c7f9ff 00000000 00000020
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Athlon(tm) Processor stepping 04
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb130, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20030918
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
SCSI subsystem initialized
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 9
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
Machine check exception polling timer started.
devfs: v1.22 (20021013) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
udf: registering filesystem
Applying VIA southbridge workaround.
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Processor [CPU0] (supports C1 C2, 2 throttling states)
pty: 256 Unix98 ptys configured
request_module: failed /sbin/modprobe -- parport_lowlevel. error = -16
lp: driver loaded but no devices found
Linux agpgart interface v0.100 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
parport0: PC-style at 0x378 [PCSPP(,...)]
lp0: using parport0 (polling).
lp0: console ready
parport_pc: Via 686A parallel port: io=0x378
Using anticipatory io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:00:0a.0: 3Com PCI 3c900 Boomerang 10Mbps Combo at 0xec00. Vers LK1.1.19
eth0: Dropping NETIF_F_SG since no checksum feature.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hda: Maxtor 6Y120P0, ATA DISK drive
hdb: WDC WD800BB-00CAA1, ATA DISK drive
hdd: CD-ROM 56X L, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 240121728 sectors (122942 MB) w/7936KiB Cache, CHS=65535/16/63
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3
hdb: max request size: 128KiB
hdb: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=65535/16/63
/dev/ide/host0/bus0/target1/lun0: p1 p2 p3
hdd: ATAPI 56X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.12
drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver v2.1
uhci-hcd 0000:00:07.2: UHCI Host Controller
uhci-hcd 0000:00:07.2: irq 9, io base 0000d400
uhci-hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
uhci-hcd 0000:00:07.3: UHCI Host Controller
uhci-hcd 0000:00:07.3: irq 9, io base 0000d800
uhci-hcd 0000:00:07.3: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
drivers/usb/core/usb.c: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
drivers/usb/core/usb.c: registered new driver usb-storage
USB Mass Storage support registered.
drivers/usb/core/usb.c: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
input: PS/2 Generic Mouse on isa0060/serio1
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Advanced Linux Sound Architecture Driver Version 0.9.7 (Thu Sep 25 19:16:36 2003 UTC).
request_module: failed /sbin/modprobe -- snd-card-0. error = -16
PCI: Setting latency timer of device 0000:00:07.5 to 64
hub 1-0:1.0: new USB device on port 1, assigned address 2
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 2 ports detected
ALSA device list:
#0: VIA 82C686A/B rev50 at 0xdc00, irq 5
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S1 S4 S5)
hub 1-1:1.0: new USB device on port 1, assigned address 3
found reiserfs format "3.6" with standard journal
Reiserfs journal params: device hda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (hda3) for (hda3)
Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 132k freed
drivers/usb/input/hid-core.c: ctrl urb status -104 received
drivers/usb/input/hid-core.c: timeout initializing reports
input: USB HID v1.00 Keyboard [BTC USB Keyboard] on usb-0000:00:07.2-1.1
Adding 1020116k swap on /dev/hda2. Priority:-1 extents:1
spurious 8259A interrupt: IRQ7.
|
I'm not really good at this stuff. Above is my dmesg output. If any more info is needed please tell what info and how to get it from the console 
Best Regards, Börkur Ingi Jónsson
_________________
______________
Regards, Berkz |
|
| Back to top |
|
 |
Lovechild
Advocate
Joined: 17 May 2002
Posts: 2858
Location: Århus, Denmark
|
|
| Back to top |
|
|
Berkz
Apprentice
Joined: 26 Aug 2002
Posts: 205
Location: Iceland
|
| Posted: Thu Oct 09, 2003 8:58 pm Post subject: |
|
|
Yeah I just never got a reply on the matter, so I switched back to 2.4 and Now when I decide to try it again the same error ;(
_________________
______________
Regards, Berkz |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Other Things Gentoo
