View previous topic :: View next topic |
Author |
Message |
philipo n00b
Joined: 24 Nov 2008 Posts: 34
|
Posted: Tue Jan 15, 2013 11:24 pm Post subject: Graphic card Ati radeon HD7850 and X |
|
|
Hello, I built new pc with ati HD7850 and I have problem to configure X. Procedure was that I put to make.conf VIDEO_CARDS="fglrx" and then emerge xorg-x11. Next I started Xorg -configure but it fail with message "No devices to configure". Fglrx module looks that works good. Is any settings in kernel which i should use?Thanks for help! i7-3820,ga-x79-ud3, kernel-3.6.11 |
|
Back to top |
|
|
DONAHUE Watchman
Joined: 09 Dec 2006 Posts: 7651 Location: Goose Creek SC
|
Posted: Wed Jan 16, 2013 6:21 am Post subject: |
|
|
did you Code: | emerge linux-firmware |
did you run Code: | rm /etc/X11/xorg.conf
aticonfig --initial |
_________________ Defund the FCC. |
|
Back to top |
|
|
DaggyStyle Watchman
Joined: 22 Mar 2006 Posts: 5910
|
Posted: Wed Jan 16, 2013 6:39 am Post subject: |
|
|
DONAHUE wrote: | did you Code: | emerge linux-firmware |
did you run Code: | rm /etc/X11/xorg.conf
aticonfig --initial |
|
afaik linux-firmware contains the fw for the foss driver, Fglrx should run regardless if it is installed or not. _________________ Only two things are infinite, the universe and human stupidity and I'm not sure about the former - Albert Einstein |
|
Back to top |
|
|
philipo n00b
Joined: 24 Nov 2008 Posts: 34
|
Posted: Wed Jan 16, 2013 8:02 am Post subject: still not work |
|
|
I tried emerge linux-firmware, but it did not help.
I put lsmod and fglrx was showed but in column "used by" is 0 (i think it should not be). Next I put dmesg and I found ATi radeon 7800 ..etc.... which is ok.
Last edited by philipo on Wed Jan 16, 2013 8:06 am; edited 1 time in total |
|
Back to top |
|
|
DaggyStyle Watchman
Joined: 22 Mar 2006 Posts: 5910
|
Posted: Wed Jan 16, 2013 8:04 am Post subject: |
|
|
have you ran aticonfig --initial as DONAHUE suggested? if so, make sure X uses the resulting file and if so, please post the content of /var/log/Xorg.0.log _________________ Only two things are infinite, the universe and human stupidity and I'm not sure about the former - Albert Einstein |
|
Back to top |
|
|
philipo n00b
Joined: 24 Nov 2008 Posts: 34
|
Posted: Wed Jan 16, 2013 8:10 am Post subject: |
|
|
yes, and when I startx I got blank screen computer freeze. Now I am at work -xorg.log can send later.
I check kernel and try reinstall ati-drivers per http://en.gentoo-wiki.com/wiki/Fglrx#Installing...I will see... |
|
Back to top |
|
|
philipo n00b
Joined: 24 Nov 2008 Posts: 34
|
Posted: Wed Jan 16, 2013 6:45 pm Post subject: |
|
|
I little play with this but without results
my Xorg.0.log:
Code: | (WW) Open ACPI failed (var/run/acpid.socket) (no such file or directory)
(WW) Falling back to old probe method for fglrx
(WW) fglrx: No matching device section for instance (BusID PCI :0@1:0:1)
(WW) fglrx(0) Board is unkown third party board, chipset is supported
(WW) fglrx(0) Option "VendorName" is not used
(WW) fglrx(0) Option "ModelName" is not used
(WW) Warning, couldn§t open module evdev |
|
|
Back to top |
|
|
philipo n00b
Joined: 24 Nov 2008 Posts: 34
|
Posted: Wed Jan 16, 2013 6:58 pm Post subject: |
|
|
Code: | (WW) Open ACPI failed (var/run/acpid.socket) (no such file or directory) |
ACPID resolved I started with /etc/init.d/acpid start and then put "rc-update add acpid boot" |
|
Back to top |
|
|
DONAHUE Watchman
Joined: 09 Dec 2006 Posts: 7651 Location: Goose Creek SC
|
Posted: Wed Jan 16, 2013 6:59 pm Post subject: |
|
|
Code: | emerge wgetpaste
rm /etc/X11/xorg.conf
aticonfig --initial | wgetpaste
wgetpaste /etc/X11/xorg.conf
startx | wgetpaste
wgetpaste /var/log/Xorg.0.log
lspci -k |wgetpaste
emerge --info | wgetpaste
emerge -s ati-drivers xorg-server | wgetpaste | and post url's returned here _________________ Defund the FCC. |
|
Back to top |
|
|
philipo n00b
Joined: 24 Nov 2008 Posts: 34
|
Posted: Wed Jan 16, 2013 7:07 pm Post subject: |
|
|
, do not know how, but I resolved it.
I disabled Code: | Device Drivers --->
Graphics support --->
< > Direct Rendering Manager (XFree86 4.1.0 and higher DRI support) ---> |
in kernel, then remerge ati-drivers and xorg-drivers, started acpi and emerge twm xclock and xterm. Thank you for help |
|
Back to top |
|
|
DONAHUE Watchman
Joined: 09 Dec 2006 Posts: 7651 Location: Goose Creek SC
|
Posted: Wed Jan 16, 2013 7:10 pm Post subject: |
|
|
fglrx provides its own DRM, good work _________________ Defund the FCC. |
|
Back to top |
|
|
philipo n00b
Joined: 24 Nov 2008 Posts: 34
|
Posted: Wed Jan 16, 2013 7:10 pm Post subject: |
|
|
but keyboard and mouse did not work . I try again generate xorg.conf |
|
Back to top |
|
|
philipo n00b
Joined: 24 Nov 2008 Posts: 34
|
Posted: Wed Jan 16, 2013 7:14 pm Post subject: |
|
|
I am not able generate xorg.conf with Xorg -configure
Every time a I got "No devices to configure. Configuration failed"..it is same as at the beginning... |
|
Back to top |
|
|
DONAHUE Watchman
Joined: 09 Dec 2006 Posts: 7651 Location: Goose Creek SC
|
Posted: Wed Jan 16, 2013 7:18 pm Post subject: |
|
|
Don't even try this: Quote: | I am not able generate xorg.conf with Xorg -configure
Every time a I got "No devices to configure. Configuration failed"..it is same as at the beginning... |
Code: | rm /etc/X11/xorg.conf
aticonfig --initial | is for your needs even if Xorg --configure worked. _________________ Defund the FCC. |
|
Back to top |
|
|
philipo n00b
Joined: 24 Nov 2008 Posts: 34
|
Posted: Wed Jan 16, 2013 7:26 pm Post subject: |
|
|
DONAHUE wrote: | Don't even try this: Quote: | I am not able generate xorg.conf with Xorg -configure
Every time a I got "No devices to configure. Configuration failed"..it is same as at the beginning... |
Code: | rm /etc/X11/xorg.conf
aticonfig --initial | is for your needs even if Xorg --configure worked. |
But aticonfig --initial generate only for monitor and graphic card I need add keyboard, mouse etc. |
|
Back to top |
|
|
DONAHUE Watchman
Joined: 09 Dec 2006 Posts: 7651 Location: Goose Creek SC
|
Posted: Wed Jan 16, 2013 7:28 pm Post subject: |
|
|
Code: | emerge -1 xf86-input-evdev |
Code: | emerge wgetpaste
wgetpaste /var/log/Xorg.0.log
wgetpaste /etc/portage/make.conf | and posting the url's returned would help analysis _________________ Defund the FCC.
Last edited by DONAHUE on Wed Jan 16, 2013 7:36 pm; edited 1 time in total |
|
Back to top |
|
|
philipo n00b
Joined: 24 Nov 2008 Posts: 34
|
Posted: Wed Jan 16, 2013 7:36 pm Post subject: |
|
|
DONAHUE wrote: | Code: | emerge -1 xf86-input-evdev |
|
Great! It works.
I think, it was mistake that I do not put X to USE in make.conf |
|
Back to top |
|
|
philipo n00b
Joined: 24 Nov 2008 Posts: 34
|
Posted: Wed Jan 16, 2013 7:37 pm Post subject: |
|
|
Ok, X working now...I will continue on KDE desktop. Thank you |
|
Back to top |
|
|
DONAHUE Watchman
Joined: 09 Dec 2006 Posts: 7651 Location: Goose Creek SC
|
Posted: Wed Jan 16, 2013 7:40 pm Post subject: |
|
|
you might want to Code: | eselect profile list | and select a profile that matches your intended use like desktop or desktop/kde or .. then emerge -uND world; a useful profile incorporates a good basic set of USE flags. _________________ Defund the FCC. |
|
Back to top |
|
|
philipo n00b
Joined: 24 Nov 2008 Posts: 34
|
Posted: Wed Jan 16, 2013 7:45 pm Post subject: |
|
|
DONAHUE wrote: | you might want to Code: | eselect profile list | and select a profile that matches your intended use like desktop or desktop/kde or .. then emerge -uND world; a useful profile incorporates a good basic set of USE flags. |
I selected "5" with KDE when installing base system, I try do emerge -uND world |
|
Back to top |
|
|
|