View previous topic :: View next topic |
Author |
Message |
mv Watchman
Joined: 20 Apr 2005 Posts: 6749
|
Posted: Mon Jan 07, 2013 7:25 pm Post subject: DVBT with Terratec Cinergy Stick: feed not in list |
|
|
I have a dvbt stick (Terratec Cincergy) for which lspci gives the id: 0ccd:00d3
According to some web pages, this should be supported by >=linux-3.7 with the RTL28XXU driver which I activated in the kernel and modprobe'd.
w_scan was able to produce a list of channels which I copied to /etc/mplayer/channels.conf, but nevertheless mplayer gives an error (and with xine-ui, kaffeine, vlc I didn't succeed either):
mplayer dvb:// wrote: | ERROR IN SETTING DMX_FILTER 8468 for fd 4: ERRNO: 22ERROR, COULDN'T SET CHANNEL 0: Failed to open dvb:// |
Simultaneously, the kernel throws the error
dmesg wrote: | dvb_demux_feed_del: feed not in list (type=0 state=0 pid=ffff) |
Any ideas what I might be doing wrong? (I have never attempted dvbt before, so maybe I did a very stupid mistake...)
Last edited by mv on Mon Jan 07, 2013 7:52 pm; edited 1 time in total |
|
Back to top |
|
|
NeddySeagoon Administrator
Joined: 05 Jul 2003 Posts: 54431 Location: 56N 3W
|
Posted: Mon Jan 07, 2013 7:28 pm Post subject: |
|
|
mv,
What does dmesg day about firmware loading ? _________________ Regards,
NeddySeagoon
Computer users fall into two groups:-
those that do backups
those that have never had a hard drive fail. |
|
Back to top |
|
|
mv Watchman
Joined: 20 Apr 2005 Posts: 6749
|
Posted: Mon Jan 07, 2013 7:52 pm Post subject: |
|
|
NeddySeagoon wrote: | What does dmesg day about firmware loading ? |
The only messages when inserting the stick are dmesg wrote: | input: TerraTec Cinergy T Stick RC (Rev. 3) as /devices/pci0000:00/0000:00:1d.7/usb1/1-4/rc/rc0/input6
rc0: TerraTec Cinergy T Stick RC (Rev. 3) as /devices/pci0000:00/0000:00:1d.7/usb1/1-4/rc/rc0
usb 1-4: dvb_usb_v2: schedule remote query interval to 400 msecs
usb 1-4: dvb_usb_v2: 'TerraTec Cinergy T Stick RC (Rev. 3)' successfully initialized and connected |
(and then the mentioned error if I start mplayer). In .config I have egrep 'FIRM|FW' .config wrote: | CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_FIRMWARE_IN_KERNEL is not set
CONFIG_EXTRA_FIRMWARE=""
# CONFIG_LIBERTAS_THINFIRM is not set
# CONFIG_DVB_USB_CYPRESS_FIRMWARE is not set
# CONFIG_DRM_LOAD_EDID_FIRMWARE is not set
CONFIG_FIRMWARE_EDID=y
# CONFIG_USB_ISIGHTFW is not set
CONFIG_FIRMWARE_MEMMAP=y
# CONFIG_GOOGLE_FIRMWARE is not set |
I tried with stable udev (sys-fs/udev-171-r9 and sys-fs/eudev-0). Maybe I need testing udev for firmware loading? |
|
Back to top |
|
|
mv Watchman
Joined: 20 Apr 2005 Posts: 6749
|
Posted: Mon Jan 07, 2013 8:22 pm Post subject: |
|
|
After setting CONFIG_FIRMWARE_IN_KERNEL=y the result is the same
Anyway, my /etc/firmware is rather small:
/etc/firmware wrote: | av7110/bootcode.bin
ttusb-budget/dspbootcode.bin | Maybe I have to get a special firmware blob from somewhere? |
|
Back to top |
|
|
NeddySeagoon Administrator
Joined: 05 Jul 2003 Posts: 54431 Location: 56N 3W
|
Posted: Mon Jan 07, 2013 8:37 pm Post subject: |
|
|
mv,
It does not need firmware. Its reported to work but its not clear if you still need the device ID patch or not. _________________ Regards,
NeddySeagoon
Computer users fall into two groups:-
those that do backups
those that have never had a hard drive fail. |
|
Back to top |
|
|
mv Watchman
Joined: 20 Apr 2005 Posts: 6749
|
Posted: Mon Jan 07, 2013 9:03 pm Post subject: |
|
|
NeddySeagoon,
I had found this webpage already, but it seems that the RTL28XXU driver (or maybe all of dvd-usb-v2) was rather restructured since then: I found nothing which looks even closely to the code in that patch. However, since the stick is recognized after inserting, I guess that the correct ID is already included. |
|
Back to top |
|
|
|