View previous topic :: View next topic |
Author |
Message |
someoneG n00b
Joined: 26 Nov 2011 Posts: 13
|
Posted: Fri Dec 28, 2012 7:36 pm Post subject: Another hostapd problem |
|
|
Hi,
im struggling with hostapd and i cant seem to find a solution to this.
My network setup is pretty easy: I want to have my laptop as wlan gateway for my mobile phone.
I will set up bridging or NAT/Masqarade as needed after i manage to start hostapd.
So far i took the minimal configuration
Code: | interface=wlan0
driver=nl80211
ssid=test
channel=1 |
After finding out all the things i forgot in my kernel/USE i am now at a point, where i seem to be unable to proceed any further.
hostapd -dd ~/minimal.conf
gets me:
Code: | random: Trying to read entropy from /dev/random
Configuration file: /root/minimal.conf
nl80211: interface wlan0 in phy phy0
rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0
rfkill: initial event: idx=1 type=2 op=0 soft=0 hard=0
nl80211: Using driver-based off-channel TX
nl80211: Add own interface ifindex 4
nl80211: Set mode ifindex 4 iftype 3 (AP)
nl80211: Failed to set interface 4 to mode 3: -95 (Operation not supported)
nl80211: Interface already in requested mode - ignore error
nl80211: Create interface iftype 6 (MONITOR)
nl80211: New interface mon.wlan0 created: ifindex=7
nl80211: Add own interface ifindex 7
BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits)
nl80211: Regulatory information - country=00
nl80211: 2402-2472 @ 40 MHz
nl80211: 2457-2482 @ 20 MHz
nl80211: 2474-2494 @ 20 MHz
nl80211: 5170-5250 @ 40 MHz
nl80211: 5735-5835 @ 40 MHz
nl80211: Added 802.11b mode based on 802.11g information
Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=15 dBm
Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=15 dBm
Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=15 dBm
Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=15 dBm
Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=15 dBm
Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=15 dBm
Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=15 dBm
Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=15 dBm
Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=15 dBm
Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=15 dBm
Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=15 dBm
Allowed channel: mode=2 chan=36 freq=5180 MHz max_tx_power=15 dBm
Allowed channel: mode=2 chan=40 freq=5200 MHz max_tx_power=15 dBm
Allowed channel: mode=2 chan=44 freq=5220 MHz max_tx_power=15 dBm
Allowed channel: mode=2 chan=48 freq=5240 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=15 dBm
Completing interface initialization
Mode: IEEE 802.11b Channel: 1 Frequency: 2412 MHz
nl80211: Set freq 2412 (ht_enabled=0 sec_channel_offset=0)
nl80211: Failed to set channel (freq=2412): -16 (Device or resource busy)
Could not set channel for kernel driver
wlan0: Unable to setup interface.
Flushing old station entries
Could not connect to kernel driver.
Deauthenticate all stations
nl80211: Remove interface ifindex=7
netlink: Operstate: linkmode=0, operstate=6
nl80211: Set mode ifindex 4 iftype 2 (STATION)
|
And thats it. exitcode 1.
uname -a
Code: | Linux hostname 3.7.1-gentoo #7 SMP Fri Dec 28 20:17:41 CET 2012 x86_64 Intel(R) Core(TM)2 Duo CPU T9300 @ 2.50GHz GenuineIntel GNU/Linux |
hostapd -v
Code: | hostapd v1.1
User space daemon for IEEE 802.11 AP management,
IEEE 802.1X/WPA/WPA2/EAP/RADIUS Authenticator
Copyright (c) 2002-2012, Jouni Malinen <j@w1.fi> and contributors |
lspci -k
Code: | 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01)
Subsystem: ASUSTeK Computer Inc. A6J-Q008
Kernel driver in use: r8169
06:00.0 Network controller: Intel Corporation PRO/Wireless 4965 AG or AGN [Kedron] Network Connection (rev 61)
Subsystem: Intel Corporation PRO/Wireless 4965 AG or AGN
Kernel driver in use: iwl4965
|
/etc/conf.d/net
Code: | config_eth0="dhcp"
modules_wlan0="!wpa_supplicant !iwconfig"
config_wlan0="null" |
both net.eth0 + net wlan0 are in default rc level and seem to come up fine and actually worked before. (firmware seems to be within linux-firmware package)
iw list
Code: | Wiphy phy0
Band 1:
Capabilities: 0x820
HT20
Static SM Power Save
RX HT20 SGI
No RX STBC
Max AMSDU length: 7935 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 4 usec (0x05)
HT RX MCS rate indexes supported: 0-23
TX unequal modulation not supported
HT TX Max spatial streams: 2
HT TX MCS rate indexes supported may differ
Frequencies:
* 2412 MHz [1] (15.0 dBm)
* 2417 MHz [2] (15.0 dBm)
* 2422 MHz [3] (15.0 dBm)
* 2427 MHz [4] (15.0 dBm)
* 2432 MHz [5] (15.0 dBm)
* 2437 MHz [6] (15.0 dBm)
* 2442 MHz [7] (15.0 dBm)
* 2447 MHz [8] (15.0 dBm)
* 2452 MHz [9] (15.0 dBm)
* 2457 MHz [10] (15.0 dBm)
* 2462 MHz [11] (15.0 dBm)
* 2467 MHz [12] (15.0 dBm) (passive scanning, no IBSS)
* 2472 MHz [13] (15.0 dBm) (passive scanning, no IBSS)
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps (short preamble supported)
* 5.5 Mbps (short preamble supported)
* 11.0 Mbps (short preamble supported)
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Band 2:
Capabilities: 0x862
HT20/HT40
Static SM Power Save
RX HT20 SGI
RX HT40 SGI
No RX STBC
Max AMSDU length: 7935 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 4 usec (0x05)
HT RX MCS rate indexes supported: 0-23, 32
TX unequal modulation not supported
HT TX Max spatial streams: 2
HT TX MCS rate indexes supported may differ
Frequencies:
* 5180 MHz [36] (15.0 dBm)
* 5200 MHz [40] (15.0 dBm)
* 5220 MHz [44] (15.0 dBm)
* 5240 MHz [48] (15.0 dBm)
* 5260 MHz [52] (15.0 dBm) (passive scanning, no IBSS, radar detection)
* 5280 MHz [56] (15.0 dBm) (passive scanning, no IBSS, radar detection)
* 5300 MHz [60] (15.0 dBm) (passive scanning, no IBSS, radar detection)
* 5320 MHz [64] (15.0 dBm) (passive scanning, no IBSS, radar detection)
* 5500 MHz [100] (15.0 dBm) (passive scanning, no IBSS, radar detection)
* 5520 MHz [104] (15.0 dBm) (passive scanning, no IBSS, radar detection)
* 5540 MHz [108] (15.0 dBm) (passive scanning, no IBSS, radar detection)
* 5560 MHz [112] (15.0 dBm) (passive scanning, no IBSS, radar detection)
* 5580 MHz [116] (15.0 dBm) (passive scanning, no IBSS, radar detection)
* 5600 MHz [120] (15.0 dBm) (passive scanning, no IBSS, radar detection)
* 5620 MHz [124] (15.0 dBm) (passive scanning, no IBSS, radar detection)
* 5640 MHz [128] (15.0 dBm) (passive scanning, no IBSS, radar detection)
* 5660 MHz [132] (15.0 dBm) (passive scanning, no IBSS, radar detection)
* 5680 MHz [136] (15.0 dBm) (passive scanning, no IBSS, radar detection)
* 5700 MHz [140] (15.0 dBm) (passive scanning, no IBSS, radar detection)
Bitrates (non-HT):
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
max # scan SSIDs: 20
max scan IEs length: 127 bytes
Coverage class: 0 (up to 0m)
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP (00-0f-ac:4)
Available Antennas: TX 0 RX 0
Supported interface modes:
* IBSS
* managed
* monitor
software interface modes (can always be added):
* monitor
interface combinations are not supported
Supported commands:
* new_interface
* set_interface
* new_key
* start_ap
* new_station
* set_bss
* authenticate
* associate
* deauthenticate
* disassociate
* join_ibss
* set_tx_bitrate_mask
* frame
* frame_wait_cancel
* set_wiphy_netns
* set_channel
* set_wds_peer
* probe_client
* set_noack_map
* register_beacons
* start_p2p_device
* testmode
* connect
* disconnect
Supported TX frame types:
* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
* IBSS: 0xb0 0xc0 0xd0
* managed: 0x40 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* mesh point: 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* P2P-device: 0x40 0xd0
Device supports RSN-IBSS.
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
Device supports TX status socket option.
Device supports HT-IBSS.
|
Any ideas on how to make hostapd not fail? |
|
Back to top |
|
|
Ant P. Watchman
Joined: 18 Apr 2009 Posts: 6920
|
Posted: Fri Dec 28, 2012 7:43 pm Post subject: |
|
|
Quote: | Code: | nl80211: Failed to set channel (freq=2412): -16 (Device or resource busy) |
|
Looks like something else may be trying to control the device. Do you have any leftover wpa_supplicant processes running?
On my system I'm using this:
Code: | config_wlan0="null"
modules="!wireless" |
|
|
Back to top |
|
|
someoneG n00b
Joined: 26 Nov 2011 Posts: 13
|
Posted: Fri Dec 28, 2012 8:00 pm Post subject: |
|
|
/etc/conf.d/net
Code: | config_eth0="dhcp"
modules_wlan0="!wpa_supplicant !iwconfig !wireless"
config_wlan0="null" |
Rebooted. No wpa_supplicant is running. No Networkmanager is running. No anything seems to be running.
Still no change: device busy.
ps aux
Code: | USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND
root 1 1.1 0.0 4220 724 ? Ss 20:57 0:01 init [3]
root 2 0.0 0.0 0 0 ? S 20:57 0:00 [kthreadd]
root 3 0.0 0.0 0 0 ? S 20:57 0:00 [ksoftirqd/0]
root 4 0.0 0.0 0 0 ? S 20:57 0:00 [kworker/0:0]
root 5 0.0 0.0 0 0 ? S< 20:57 0:00 [kworker/0:0H]
root 6 0.0 0.0 0 0 ? S 20:57 0:00 [kworker/u:0]
root 7 0.0 0.0 0 0 ? S< 20:57 0:00 [kworker/u:0H]
root 8 0.0 0.0 0 0 ? S 20:57 0:00 [migration/0]
root 9 0.0 0.0 0 0 ? S 20:57 0:00 [rcu_bh]
root 10 0.0 0.0 0 0 ? S 20:57 0:00 [rcu_sched]
root 11 0.0 0.0 0 0 ? S 20:57 0:00 [ksoftirqd/1]
root 12 0.0 0.0 0 0 ? S 20:57 0:00 [migration/1]
root 13 0.0 0.0 0 0 ? S 20:57 0:00 [kworker/1:0]
root 14 0.0 0.0 0 0 ? S< 20:57 0:00 [kworker/1:0H]
root 15 0.0 0.0 0 0 ? S< 20:57 0:00 [khelper]
root 16 0.0 0.0 0 0 ? S 20:57 0:00 [kdevtmpfs]
root 17 0.0 0.0 0 0 ? S 20:57 0:00 [kworker/u:1]
root 247 0.0 0.0 0 0 ? S 20:57 0:00 [bdi-default]
root 248 0.0 0.0 0 0 ? S< 20:57 0:00 [kintegrityd]
root 250 0.0 0.0 0 0 ? S< 20:57 0:00 [kblockd]
root 377 0.0 0.0 0 0 ? S< 20:57 0:00 [ata_sff]
root 385 0.0 0.0 0 0 ? S 20:57 0:00 [khubd]
root 401 0.0 0.0 0 0 ? S 20:57 0:00 [kworker/0:1]
root 402 0.0 0.0 0 0 ? S 20:57 0:00 [kworker/1:1]
root 520 0.0 0.0 0 0 ? S 20:57 0:00 [kswapd0]
root 587 0.0 0.0 0 0 ? S 20:57 0:00 [fsnotify_mark]
root 611 0.0 0.0 0 0 ? S< 20:57 0:00 [crypto]
root 680 0.0 0.0 0 0 ? S 20:57 0:00 [kworker/u:2]
root 710 0.0 0.0 0 0 ? S< 20:57 0:00 [ttm_swap]
root 757 0.0 0.0 0 0 ? S 20:57 0:00 [scsi_eh_0]
root 760 0.0 0.0 0 0 ? S 20:57 0:00 [scsi_eh_1]
root 763 0.0 0.0 0 0 ? S 20:57 0:00 [scsi_eh_2]
root 766 0.0 0.0 0 0 ? S 20:57 0:00 [kworker/u:3]
root 767 0.0 0.0 0 0 ? S 20:57 0:00 [kworker/u:4]
root 779 0.0 0.0 0 0 ? S 20:57 0:00 [scsi_eh_3]
root 782 0.0 0.0 0 0 ? S 20:57 0:00 [scsi_eh_4]
root 785 0.0 0.0 0 0 ? S 20:57 0:00 [kworker/u:5]
root 786 0.0 0.0 0 0 ? S 20:57 0:00 [kworker/u:6]
root 825 0.0 0.0 0 0 ? S 20:57 0:00 [kworker/0:2]
root 838 0.0 0.0 0 0 ? S< 20:57 0:00 [kpsmoused]
root 852 0.0 0.0 0 0 ? S< 20:57 0:00 [hd-audio0]
root 874 0.0 0.0 0 0 ? S 20:57 0:00 [kworker/u:7]
root 894 0.0 0.0 0 0 ? S< 20:57 0:00 [kworker/0:1H]
root 895 0.0 0.0 0 0 ? S< 20:57 0:00 [deferwq]
root 897 0.0 0.0 0 0 ? S< 20:57 0:00 [kworker/1:1H]
root 898 0.0 0.0 0 0 ? S 20:57 0:00 [btrfs-worker-1]
root 899 0.0 0.0 0 0 ? S 20:57 0:00 [btrfs-genwork-1]
root 900 0.0 0.0 0 0 ? S 20:57 0:00 [btrfs-submit-1]
root 901 0.0 0.0 0 0 ? S 20:57 0:00 [btrfs-delalloc-]
root 902 0.0 0.0 0 0 ? S 20:57 0:00 [btrfs-fixup-1]
root 903 0.5 0.0 0 0 ? S 20:57 0:00 [btrfs-endio-1]
root 904 0.1 0.0 0 0 ? S 20:57 0:00 [btrfs-endio-met]
root 905 0.0 0.0 0 0 ? S 20:57 0:00 [btrfs-endio-met]
root 906 0.0 0.0 0 0 ? S 20:57 0:00 [btrfs-endio-wri]
root 907 0.0 0.0 0 0 ? S 20:57 0:00 [btrfs-freespace]
root 908 0.0 0.0 0 0 ? S 20:57 0:00 [btrfs-delayed-m]
root 909 0.0 0.0 0 0 ? S 20:57 0:00 [btrfs-cache-1]
root 910 0.0 0.0 0 0 ? S 20:57 0:00 [btrfs-readahead]
root 918 0.0 0.0 0 0 ? S 20:57 0:00 [btrfs-cleaner]
root 919 0.0 0.0 0 0 ? S 20:57 0:00 [btrfs-transacti]
root 927 0.1 0.0 0 0 ? S 20:57 0:00 [btrfs-endio-2]
root 1037 0.1 0.0 33380 1728 ? Ss 20:57 0:00 /usr/lib/systemd/systemd-udevd --daemon
root 1104 0.0 0.0 0 0 ? S< 20:57 0:00 [cfg80211]
root 1161 0.0 0.0 0 0 ? S< 20:57 0:00 [led_workqueue]
root 1168 0.0 0.0 0 0 ? S< 20:57 0:00 [iwl4965]
root 1197 0.0 0.0 0 0 ? S 20:57 0:00 [btrfs-endio-3]
root 1198 0.0 0.0 0 0 ? S 20:57 0:00 [btrfs-endio-4]
root 1205 0.0 0.0 0 0 ? S 20:57 0:00 [scsi_eh_5]
root 1206 0.0 0.0 0 0 ? S 20:57 0:00 [usb-storage]
root 1210 0.0 0.0 0 0 ? S< 20:57 0:00 [hci0]
root 1211 0.0 0.0 0 0 ? S< 20:57 0:00 [kworker/u:1H]
root 1212 0.0 0.0 0 0 ? S 20:57 0:00 [kworker/1:2]
root 1719 0.0 0.0 27204 440 ? S 20:57 0:00 supervising syslog-ng
root 1720 0.0 0.0 61216 3476 ? Ss 20:57 0:00 /usr/sbin/syslog-ng --cfgfile /etc/syslog-ng/syslog-ng.conf --pidfile /var/run/syslog-ng.pid
root 1733 0.0 0.0 4228 648 ? Ss 20:57 0:00 /usr/sbin/acpid
root 1790 0.0 0.0 0 0 ? S 20:57 0:00 [kworker/1:3]
root 1846 0.0 0.0 29952 1184 ? Ss 20:57 0:00 /usr/sbin/sshd
root 1851 0.0 0.0 0 0 ? S 20:57 0:00 [flush-btrfs-1]
root 1852 0.0 0.0 0 0 ? S 20:57 0:00 [btrfs-delalloc-]
message+ 1855 0.0 0.0 19648 1120 ? Ss 20:57 0:00 /usr/bin/dbus-daemon --system
root 1885 0.0 0.0 0 0 ? S 20:58 0:00 [btrfs-endio-met]
root 1886 0.0 0.0 0 0 ? S 20:58 0:00 [btrfs-endio-met]
root 1887 0.0 0.0 0 0 ? S 20:58 0:00 [btrfs-endio-met]
root 2014 0.0 0.0 1040928 3776 ? Ssl 20:58 0:00 /usr/sbin/console-kit-daemon
polkitd 2107 0.0 0.0 366844 6992 ? Sl 20:58 0:00 /usr/lib/polkit-1/polkitd --no-debug
root 2133 0.0 0.0 26840 792 ? Ss 20:58 0:00 /usr/bin/kdm
root 2137 0.0 0.0 0 0 ? S 20:58 0:00 [btrfs-endio-wri]
root 2147 0.4 0.2 109844 16884 tty7 Ss+ 20:58 0:00 /usr/bin/X -br -novtswitch -quiet :0 vt7 -nolisten tcp -auth /var/run/xauth/A:0-oT5tab
root 2148 0.0 0.0 0 0 ? S 20:58 0:00 [btrfs-endio-wri]
root 2151 0.1 0.1 54688 11396 ? SNs 20:58 0:00 /usr/bin/perl -wT /usr/sbin/munin-node --config /etc/munin/munin-node.conf
root 2164 0.0 0.0 12632 800 ? Ss 20:58 0:00 /usr/sbin/crond
root 2236 0.0 0.0 41524 1528 ? S 20:58 0:00 -:0
kdm 2244 0.9 0.4 308388 39792 ? Sl 20:58 0:00 /usr/lib64/kde4/libexec/kdm_greet
root 2393 0.0 0.0 24756 1408 ? Ss 20:58 0:00 /usr/sbin/ntpd -p /var/run/ntpd.pid -g
root 2396 0.0 0.0 8572 356 ? Ss 20:58 0:00 dhcpcd -m 2 eth0
root 2440 0.0 0.0 74280 3516 ? Ss 20:58 0:00 sshd: root@pts/0
distcc 2463 0.0 0.0 8948 280 ? SNs 20:58 0:00 /usr/bin/distccd --daemon --pid-file /var/run/distccd/distccd.pid --jobs 4 --port 3632 --log-level warning --allow 10.10.0.0/16 -N 15
distcc 2464 0.0 0.0 8948 116 ? SN 20:58 0:00 /usr/bin/distccd --daemon --pid-file /var/run/distccd/distccd.pid --jobs 4 --port 3632 --log-level warning --allow 10.10.0.0/16 -N 15
root 2478 0.0 0.0 15676 1008 tty1 Ss+ 20:58 0:00 /sbin/agetty --noclear 38400 tty1 linux
root 2479 0.0 0.0 15676 1004 tty2 Ss+ 20:58 0:00 /sbin/agetty 38400 tty2 linux
root 2480 0.0 0.0 15676 1004 tty3 Ss+ 20:58 0:00 /sbin/agetty 38400 tty3 linux
root 2481 0.0 0.0 15676 1004 tty4 Ss+ 20:58 0:00 /sbin/agetty 38400 tty4 linux
root 2482 0.0 0.0 15676 1004 tty5 Ss+ 20:58 0:00 /sbin/agetty 38400 tty5 linux
root 2483 0.0 0.0 15676 1008 tty6 Ss+ 20:58 0:00 /sbin/agetty 38400 tty6 linux
distcc 2492 0.0 0.0 8948 116 ? SN 20:58 0:00 /usr/bin/distccd --daemon --pid-file /var/run/distccd/distccd.pid --jobs 4 --port 3632 --log-level warning --allow 10.10.0.0/16 -N 15
distcc 2495 0.0 0.0 8948 116 ? SN 20:58 0:00 /usr/bin/distccd --daemon --pid-file /var/run/distccd/distccd.pid --jobs 4 --port 3632 --log-level warning --allow 10.10.0.0/16 -N 15
root 2503 0.0 0.0 24436 2212 pts/0 Ss 20:58 0:00 -zsh
distcc 2504 0.0 0.0 8948 116 ? SN 20:58 0:00 /usr/bin/distccd --daemon --pid-file /var/run/distccd/distccd.pid --jobs 4 --port 3632 --log-level warning --allow 10.10.0.0/16 -N 15
root 2506 0.0 0.0 24988 1184 pts/0 S+ 20:58 0:00 screen -xR
root 2507 0.0 0.0 25416 1824 ? Rs 20:58 0:00 SCREEN -xR
root 2508 0.3 0.0 44812 4296 pts/1 Ss 20:58 0:00 -/bin/zsh
root 2715 0.0 0.0 0 0 ? S 20:58 0:00 [btrfs-worker-2]
root 2716 0.0 0.0 0 0 ? S 20:58 0:00 [btrfs-worker-3]
root 2717 0.0 0.0 0 0 ? S 20:58 0:00 [btrfs-worker-4]
root 2737 0.0 0.0 18504 1308 pts/1 R+ 20:59 0:00 ps aux
|
|
|
Back to top |
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
|