View previous topic :: View next topic |
Author |
Message |
mattylux Apprentice
Joined: 19 Jul 2008 Posts: 247 Location: bologna
|
Posted: Sun Oct 30, 2011 12:47 pm Post subject: [RISOLTO]wlan0 scomparsa |
|
|
salve
ho un problema con la mia scheda di rete
Code: | 06:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11b/g WLAN [14e4:4311] (rev 01)
|
praticamente reinstallando gentoo, nella compilazione del kernel iniziale funzionava tutto la presenza di wlan0 [/b ]c'era.
poi ho fatto delle altre modifiche al kernel e devo aver disabilitato quacosa involontariamente, sono uscito dalla configurazione senza salvare le impostazioni del kernel da quel momento la sche da wifi e scomparsa
Code: | ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:16:d4:f0:48:60
inet addr:192.168.0.104 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::216:d4ff:fef0:4860/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:36651 errors:0 dropped:0 overruns:0 frame:0
TX packets:33132 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:36878498 (35.1 MiB) TX bytes:5500827 (5.2 MiB)
Interrupt:16 Base address:0xa000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:236 errors:0 dropped:0 overruns:0 frame:0
TX packets:236 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:17032 (16.6 KiB) TX bytes:17032 (16.6 KiB)
sit0 Link encap:IPv6-in-IPv4
NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
|
e questo[b] /etc/init.d/net.wlan0 start
Code: |
mattylux linux # /etc/init.d/net.wlan0 start
* Bringing up interface wlan0
* ERROR: interface wlan0 does not exist
* Ensure that you have loaded the correct kernel module for your hardware
* ERROR: net.wlan0 failed to start |
qualche conscilglio?? _________________ Gentoo tutta la vita
Last edited by mattylux on Tue Nov 01, 2011 10:16 pm; edited 1 time in total |
|
Back to top |
|
|
djinnZ Advocate
Joined: 02 Nov 2006 Posts: 4831 Location: somewhere in L.O.S.
|
Posted: Sun Oct 30, 2011 1:29 pm Post subject: |
|
|
Rivedere la configurazione del kernel. Sezione driver. Ricompilare e risistemare.
Ricompilato il kernel è buona cosa ricompilare i moduli.
Se sei poco pratico usa genkernel --menuconfig e non fare l'eroe; gli eroi sono sono imbecilli (per lo più morti), fumo negli occhi o mistificatori, quasi sempre tutte e tre le cose.
Controllare con un bel dmesg esempio: | ath5k 0000:02:07.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
ath5k 0000:02:07.0: registered as 'phy0' | cosa viene caricato e con lspci -vvs 02:07.0: | 02:07.0 Ethernet controller: Atheros Communications Inc. Atheros AR5001X+ Wireless Network Adapter (rev 01)
Subsystem: Atheros Communications Inc. TRENDnet TEW-443PI Wireless PCI Adapter
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168 (2500ns min, 7000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fe7f0000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: ath5k | se la scheda è correttamente rilevata (possibile che un banale urto l'abbia spostata, fidati, mi ha fatto impazzire per una settimana ed è bastato usare un cacciavite a stella).
In alternativa /etc/conf.d/udev: | persistent_net_disable="no" |
Code: | rm /etc/udev/rules.d/70-persistent-net.rules | potrebbero essere soluzioni.
Da provare nell'ordine che ho indicato. I cocci sono tuoi ovviamente. _________________ scita et risus abundant in ore stultorum sed etiam semper severi insani sunt
mala tempora currunt...mater stultorum semper pregna est
Murpy'sLaw:If anything can go wrong, it will - O'Toole's Corollary:Murphy was an optimist |
|
Back to top |
|
|
mattylux Apprentice
Joined: 19 Jul 2008 Posts: 247 Location: bologna
|
Posted: Sun Oct 30, 2011 1:54 pm Post subject: |
|
|
ecco qui questo e il mio lspci -vvs 06:00.0
Code: |
06:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01)
Subsystem: Hewlett-Packard Company BCM4311 802.11b/g Wireless LAN Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 3
Region 0: Memory at 80000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
Capabilities: [58] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: 00000000 Data: 0000
Capabilities: [d0] Express (v1) Legacy Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <4us, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- |
e questo dmesg
Code: | dmesg | tail
[10713.402899] usb 3-2: usb_probe_device
[10713.402904] usb 3-2: configuration #1 chosen from 1 choice
[10713.405787] usb 3-2: adding 3-2:1.0 (config #1, interface 0)
[10713.405862] usbhid 3-2:1.0: usb_probe_interface
[10713.405867] usbhid 3-2:1.0: usb_probe_interface - got id
[10713.419108] input: Microsoft Microsoft Basic Optical Mouse v2.0 as /devices/pci0000:00/0000:00:1d.1/usb3/3-2/3-2:1.0/input/input11
[10713.419236] generic-usb 0003:045E:00CB.000A: input,hidraw0: USB HID v1.11 Mouse [Microsoft Microsoft Basic Optical Mouse v2.0 ] on usb-0000:00:1d.1-2/input0
[10713.419258] drivers/usb/core/inode.c: creating file '012'
[10713.419293] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0004
[10713.436040] uhci_hcd 0000:00:1d.1: reserve dev 12 ep81-INT, period 8, phase 4, 93 us
|
_________________ Gentoo tutta la vita |
|
Back to top |
|
|
djinnZ Advocate
Joined: 02 Nov 2006 Posts: 4831 Location: somewhere in L.O.S.
|
Posted: Sun Oct 30, 2011 2:18 pm Post subject: |
|
|
mi pare che ti manchi il esempio: | Kernel driver in use: ath5k | che ho io e comunque al massimo dovresti vedere cosa riporta Code: | dmesg | grep 06:00.0 | il tail non è utile.
Mi pare sempre che ti sei scordato il driver ma nel dubbio ti ho indicato tutte le prime possibilità di rogna e relativi rimedi.
Rivedere la configurazione del kernel, ricompilarlo (casomai potresti metterla builtin la scheda) e controllare i moduli, che siano tutti al loro posto.
[OT]gli output e le configurazioni, per chiarezza, è meglio riportarli con Code: | [code="comando"]output[/code] | od in alternativa /path/file wrote: | contenuto |
Code: | [quote="/path/file"]contenuto[/quote] | se vuoi fare uso di colori, dimensione carattere etc. [/OT] _________________ scita et risus abundant in ore stultorum sed etiam semper severi insani sunt
mala tempora currunt...mater stultorum semper pregna est
Murpy'sLaw:If anything can go wrong, it will - O'Toole's Corollary:Murphy was an optimist |
|
Back to top |
|
|
xdarma l33t
Joined: 08 Dec 2003 Posts: 719 Location: tra veneto e friuli (italy)
|
Posted: Sun Oct 30, 2011 7:36 pm Post subject: Re: wlan0 scomparsa |
|
|
Code: | 06:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11b/g WLAN [14e4:4311] (rev 01) |
Mi è capitato qulacosa di simile ;-)
mattylux wrote: | qualche conscilglio?? |
Il wiki ufficioso di gentoo: Broadcom 43xx _________________ proud user of faKeDE-4.7.3 -> back to windowmaker -> moved to LXQt |
|
Back to top |
|
|
mattylux Apprentice
Joined: 19 Jul 2008 Posts: 247 Location: bologna
|
Posted: Tue Nov 01, 2011 10:18 pm Post subject: |
|
|
risolto ho ricompilato da capo il kernel eliminando quello vecchio e tutto e funzionanto alla perfezione...
avevo disabilitato io per sbalgio qualche modulo.. _________________ Gentoo tutta la vita |
|
Back to top |
|
|
djinnZ Advocate
Joined: 02 Nov 2006 Posts: 4831 Location: somewhere in L.O.S.
|
Posted: Wed Nov 02, 2011 12:54 pm Post subject: |
|
|
mattylux wrote: | e tutto e funzionanto alla perfezione... | capisco che un errore di battitura possa scappare ma... povera lingua italiana... oggi siamo proprio in tema... una prece _________________ scita et risus abundant in ore stultorum sed etiam semper severi insani sunt
mala tempora currunt...mater stultorum semper pregna est
Murpy'sLaw:If anything can go wrong, it will - O'Toole's Corollary:Murphy was an optimist |
|
Back to top |
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
|