Gentoo Forums
Gentoo Forums
Gentoo Forums
Quick Search: in
WPA Supplicant - authentication failure x_x
View unanswered posts
View posts from last 24 hours

 
Reply to topic    Gentoo Forums Forum Index Networking & Security
View previous topic :: View next topic  
Author Message
divago
Tux's lil' helper
Tux's lil' helper


Joined: 04 Jun 2010
Posts: 84

PostPosted: Wed Feb 16, 2011 2:18 pm    Post subject: WPA Supplicant - authentication failure x_x Reply with quote

hi all
i got a little annoying problem

i currently connect to a home wlan (created by a netgear router) using a WEP encryption, with an hexadecimal passphrase
due to security issue with WEP encruption, i had to move to more secure WPA-PSK;
so i connected via eth0 to router interface, changed settings and set WPA.

now, i need to change configuration in /etc/conf.d/net to connect to wpa-psk secured wireless... and this does'nt work... it says me
"wlan0 does not support setting keys" 0.o

this is the conf.d/net i currently (with WEP) use
Code:

 modules_wlan0=( "iwconfig")
 wpa_supplicant_eth0="-Dwired" # For generic wired
 wpa_timeout_wlan0=60

# WLAN
 essid_wlan0="any"
 preferred_aps=( "Uairless" "Alice-00467134" "Uairless-di-Fastuebb" )
 associate_order_wlan0="any"
mode_wlan0="managed"
channel_wlan0="11"

and then
Code:

 key_Uairless="10-digit hex password"
 config_Uairless=( "dhcp" )
 dhcpcd_Uairless="-t 5"

and this is working fine; i'm currently connected to the wireless and all is working fine

after change to WPA-PSK i used this configuration (pretty similar, little differences)
Code:

 key_Uairless="s:10-digit ASCII password"
 config_Uairless=( "dhcp" )
 dhcpcd_Uairless="-t 5"

the only difference is the key because a) it's changed and b) it's ASCII (so i used the "s:" before the password)

BUT that's does'nt work
it refuse connections saying
Code:
Error for wireless request "Set Encode" (8B2A) :
    invalid argument "XXXXXXXX".
 *   wlan0 does not support setting keys


btw, this sound very odd to me, 'cause i'm used to connect to my parents WPA-PSK protected wireless using the following configuration:
Code:
# Casa di Mamma e Papa: "Alice-00467134"
 key_Alice_00467134="s:13-digit ASCII password"
 config_Alice_00467134=( "dhcp" )
 dhcpcd_Alice_00467134="-t 5 -N"


where's the problem??
there is something i miss, like a configuration file here or there???

ps:
this is the complete /etc/conf.d/net file
password are, of course, not reported :)
i use eth0 in wpa_supplicant while at work
Code:

 modules_eth0=( "wpa_supplicant")
 modules_wlan0=( "iwconfig")
#modules_wlan0=( "wpa_supplicant")
 wpa_supplicant_eth0="-Dwired" # For generic wired
#wpa_supplicant_wlan0="-Dwext" # For generic wireless
#wpa_supplicant_wlan0="-Dmadwifi" # For Atheros based cards
 wpa_timeout_wlan0=60

#preup () {
#if [[ ${IFACE} == "wlan0" ]]; then
#rfkill unblock all
#fi
#}

# ETH0
 config_eth0=( "dhcp" )
 dhcpcd_eth0="-N"

# WLAN
 essid_wlan0="any"
 preferred_aps=( "Uairless" "Alice-00467134" "Uairless-di-Fastuebb" )
 associate_order_wlan0="any"
#essid_wlan0="Uairless"
#essid_wlan0="Uairless_di_Fastuebb"
#essid_wlan0="Alice-00467134"
mode_wlan0="managed"
channel_wlan0="11"

# Fortezza delle Scienze: "Uairless"
 key_Uairless="HHHHHHHHHH"
 config_Uairless=( "dhcp" )
 dhcpcd_Uairless="-t 5"

# Casa di Mamma e Papa: "Alice-00467134"
 key_Alice_00467134="s:AAAAAAAAAAAAA"
 config_Alice_00467134=( "dhcp" )
 dhcpcd_Alice_00467134="-t 5 -N"

# Fortezza delle Scienze: "Uairless-di-Fastuebb"
 key_Uairless_di_Fastuebb="s:BBBBBBBBBBBBB"
 config_Uairless_di_Fastuebb=( "dhcp" )
 dhcpcd_Uairless_di_Fastuebb="-t 5 -N"


Last edited by divago on Wed Mar 02, 2011 10:34 am; edited 1 time in total
Back to top
View user's profile Send private message
divago
Tux's lil' helper
Tux's lil' helper


Joined: 04 Jun 2010
Posts: 84

PostPosted: Wed Feb 16, 2011 2:30 pm    Post subject: Reply with quote

Edit
after searching for documentation here i tried configure network with wpa_supplicant
so i edited /etc/wpa_supplicant/wpa_supplicant.conf file in this way:
Code:
ap_scan=1
ctrl_interface=/var/run/wpa_supplicant
ctrl_interface_group=root
network={
        ssid="Uairless"
        key_mgmt=NONE
        wep_key0="10-digit hex password"
        wep_tx_keyidx=0
        priority=5
        auth_alg=SHARED
        }
network={
        ssid="Uairless-di-Fastuebb"
        proto=WPA
        key_mgmt=WPA-PSK
        pairwise=CCMP TKIP
        group=CCMP TKIP WEP104 WEP40
        psk="13-digit ASCII password"
        priority=2
        }
and also edited /etc/conf.d/net in this way
Code:

 modules_wlan0=( "wpa_supplicant")
 wpa_supplicant_wlan0="-Dwext" # For generic wireless
#wpa_supplicant_wlan0="-Dmadwifi" # For Atheros based cards
 wpa_timeout_wlan0=60

# WLAN
 essid_wlan0="any"
 preferred_aps=( "Uairless" "Uairless-di-Fastuebb" )
 associate_order_wlan0="any"
mode_wlan0="managed"
channel_wlan0="11"

 config_Uairless=( "dhcp" )
 dhcpcd_Uairless="-t 5"

 config_Uairless_di_Fastuebb=( "dhcp" )
 dhcpcd_Uairless_di_Fastuebb="-t 5 -N"

btw now it's not connecting anymore
i tried both wpa_supplicant configuration (-Dwext and -Dmadwifi driver) but does'nt work either...

where's the problem then? i suppose i need to restart wpa_supplicant too but i found no /etc/init.d scritp for wpa_supplicant so i suppose it automatically stop and start again while i restart network...

Edit 2
now i changed back to the original configuration and wireless does'nt connect anymore O.O
wtf???
x_x

i could post only using NM to connect to wireless (of course NM will connect, and also Android phone connect without problem...)
Back to top
View user's profile Send private message
cach0rr0
Bodhisattva
Bodhisattva


Joined: 13 Nov 2008
Posts: 4123
Location: Houston, Republic of Texas

PostPosted: Thu Feb 17, 2011 6:37 am    Post subject: Reply with quote

for starters, go ahead and nuke networkmanager, comment out your network settings, let's get this to a completely virgin setup, start from the beginning, process of elimination

since i am lazy, i will copy and paste from something else I've typed:

cach0rr0 wrote:

-emerge wpa_supplicant, at least version 0.7.3
-emerge dhcpcd at a minimum 5.2.7 (version 4 of dhcpcd does not work with more recent kernels due to a change in the kernel's handle of carrier signals or something)
-emerge net-wireless/iw
-enable ath5k as a module, not a built-in

then start with incremental testing

1> test the driver: fire off a modprobe ath9k, and make sure the device shows up in /proc/net/wireless and/or /proc/net/dev. Udev should give it the name wlan0 (as you have seen)

2>test the ability to associate and authenticate with an access point: if the directory/file does not exist already, create /etc/wpa_supplicant/wpa_supplicant.conf and add this, changing names where necessary:

Code:

network={
ssid="crackme"
scan_ssid=1
key_mgmt=WPA-PSK
psk="awesomepassword"
}



Then in a terminal/shell (i normally do this in 'screen' for testing), fire off this:

Code:

wpa_supplicant -Dwext -i wlan0 -c /etc/wpa_supplicant/wpa_supplicant.conf


if that gives you errors, try:

Code:
wpa_supplicant -Dnl80211 -i wlan0 -c /etc/wpa_supplicant/wpa_supplicant.conf



If both give you errors, post them, as they are likely indicating some problem with the kernel, or, some missing userspace tool
If it appears to associate and authenticate correctly, go on to step3

3>test DHCP to make sure you can get an IP and all of that: in a new terminal tab, while wpa_supplicant is still running, fire off this command:

Code:

dhcpcd wlan0



If this gives you a proper IP address (and not some 169.254.x.x) then you have everything set up correctly


If you get errors at any of these steps, please post them, as they will tell us what piece is missing.

note: just a small tidbit from your previous post, -Dmadwifi is only if you're using the madwifi drivers - you aren't. You should be using either -D wext or -D nl80211
_________________
Lost configuring your system?
dump lspci -n here | see Pappy's guide | Link Stash
Back to top
View user's profile Send private message
divago
Tux's lil' helper
Tux's lil' helper


Joined: 04 Jun 2010
Posts: 84

PostPosted: Sat Feb 19, 2011 11:36 am    Post subject: Reply with quote

ok so i need to upgrade wpa_supplicant and dhcpcd (hope this doens't rise trouble to the 802.11 authentication in work network x_x )
when emerge will be finished, i'll do some tests then :)

but why ath5k as a module and not built in? i compiled built-in and wrk fine with other wep wireless plus woek fine with NM (so i suppose is just a configuration issue...)
cach0rr0 wrote:
note: just a small tidbit from your previous post, -Dmadwifi is only if you're using the madwifi drivers - you aren't. You should be using either -D wext or -D nl80211
ah ok. wrong driver then
i used madwifi 'cause i read it in some online documents

ps: i DON'T use NM and also i dislike it, but sometime using a quick-and-dirty graphical daemon to connect is easiest when you go around and connect to first available network...
Back to top
View user's profile Send private message
divago
Tux's lil' helper
Tux's lil' helper


Joined: 04 Jun 2010
Posts: 84

PostPosted: Sat Feb 19, 2011 3:35 pm    Post subject: Reply with quote

Ok i did it and... still not working :(
Code:
# wpa_supplicant -Dwext -i wlan0 -c /etc/wpa_supplicant/wpa_supplicant.conf
Trying to associate with 00:1d:8b:47:88:a8 (SSID='Uairless-di-Fastuebb' freq=2462 MHz)
Authentication with 00:1d:8b:47:88:a8 timed out.
Trying to associate with 00:1d:8b:49:2d:60 (SSID='FASTWEB-1-001D8B492D60' freq=2437 MHz)
Authentication with 00:1d:8b:49:2d:60 timed out.
Trying to associate with 00:1d:8b:49:2d:60 (SSID='FASTWEB-1-001D8B492D60' freq=2437 MHz)
Authentication with 00:1d:8b:49:2d:60 timed out.
Trying to associate with 00:1d:8b:47:88:a8 (SSID='Uairless-di-Fastuebb' freq=2462 MHz)
Authentication with 00:1d:8b:47:88:a8 timed out.
Trying to associate with 5c:33:8e:0f:85:a4 (SSID='Alice-35898276' freq=2412 MHz)
Associated with 5c:33:8e:0f:85:a4
CTRL-EVENT-EAP-STARTED EAP authentication started
CTRL-EVENT-EAP-FAILURE EAP authentication failed
Authentication with 5c:33:8e:0f:85:a4 timed out.
CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=0

The wireless i need to connect is the FIRST ONE (00:1d:8b:47:88:a8 (SSID='Uairless-di-Fastuebb' freq=2462 MHz))
and does'nt connect

oh and i also tried with different driver:
Code:
# wpa_supplicant -Dnl80211 -i wlan0 -c /etc/wpa_supplicant/wpa_supplicant.conf
[cut]
Trying to authenticate with 00:1d:8b:47:88:a8 (SSID='Uairless-di-Fastuebb' freq=2462 MHz)
Trying to associate with 00:1d:8b:47:88:a8 (SSID='Uairless-di-Fastuebb' freq=2462 MHz)
CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=3
[cut]


then, to read here and post again i (tried to) start again net.wlan0:
Code:
# /etc/init.d/net.wlan0 start
 * Starting wlan0
 *   Configuring wireless network for wlan0
 *   Trying to force preferred in case they are hidden
 *   Failed to associate with any preferred access points on wlan0
 *   Failed to configure wireless for wlan0                                                            [ !! ]

O.O
why now i can't connect???

(i had to stop net.wlan0 and start NM to connect and write here :( )
Back to top
View user's profile Send private message
cach0rr0
Bodhisattva
Bodhisattva


Joined: 13 Nov 2008
Posts: 4123
Location: Houston, Republic of Texas

PostPosted: Mon Feb 21, 2011 5:14 am    Post subject: Reply with quote

divago wrote:
ok so i need to upgrade wpa_supplicant and dhcpcd (hope this doens't rise trouble to the 802.11 authentication in work network x_x )
when emerge will be finished, i'll do some tests then :)

but why ath5k as a module and not built in? i compiled built-in and wrk fine with other wep wireless plus woek fine with NM


module is normally best for things like wireless drivers, because there are times you want to pass specific arguments when you load the module - if it's a built-in, you have to do this with a kernel command-line setting. For example, on my iwlagn machine, Wireless-N is very unreliable, however this driver supports disabling Wireless-N. So I can do modprobe iwlagn 11n_disable=y and have it just run in B/G mode. Maybe you want to play with aircrack-ng, and to do so you need to load the ath5k driver with specific parameters in order to make it enter "promiscuous mode".


divago wrote:

ps: i DON'T use NM and also i dislike it, but sometime using a quick-and-dirty graphical daemon to connect is easiest when you go around and connect to first available network...


if you want something a bit more "lean", check out wicd - it is what i normally use.

However in this case, if you look at wpa_supplicant, it is still failing to authenticate to the AP - I honestly do not have an immediate answer, it is not obvious to me from the output. I guess my first suggestion would be to make your wpa_supplicant.conf as minimal as possible when you're running it from the command-line (or just make a new file, wifitest.conf, and do -c /path/to/wifitest.conf when you manually run wpa_supplicant). For example, remove the control group stuff, remove the essid scanning stuff.

Make your wifitest.conf look like:

Code:

 network={
        ssid="example"
        scan_ssid=1
        key_mgmt=NONE
        wep_tx_keyidx=0
        wep_key0=42FEEDDEAFBABEDEAFBEEFAA55
     }


Note the key is not quoted. Quotes == string, no quotes == hex.

Also, you said you wish to connect to "Uairless-di-Fastuebb", however from your .conf that looks to be the *second* one, and also appears to be using WPA and not WEP.
For WPA, all you should need is this:

Code:

network={
ssid="crackme"
scan_ssid=1
key_mgmt=WPA-PSK
psk="mypassword"
}


Until we can get the right settings for wpa_supplicant.conf, the init script for net.wlan0 is not going to function.

Hope that helps, I am running out of ideas.
_________________
Lost configuring your system?
dump lspci -n here | see Pappy's guide | Link Stash
Back to top
View user's profile Send private message
divago
Tux's lil' helper
Tux's lil' helper


Joined: 04 Jun 2010
Posts: 84

PostPosted: Mon Feb 21, 2011 9:18 am    Post subject: Reply with quote

thanks for your help
cach0rr0 wrote:
module is normally best for things like wireless drivers, because there are times you want to pass specific arguments when you load the module - if it's a built-in, you have to do this with a kernel command-line setting. For example, on my iwlagn machine, Wireless-N is very unreliable, however this driver supports disabling Wireless-N. So I can do modprobe iwlagn 11n_disable=y and have it just run in B/G mode. Maybe you want to play with aircrack-ng, and to do so you need to load the ath5k driver with specific parameters in order to make it enter "promiscuous mode".

Oh. ok.
i'll compile like a module then :)

cach0rr0 wrote:

if you want something a bit more "lean", check out wicd - it is what i normally use.

However in this case, if you look at wpa_supplicant, it is still failing to authenticate to the AP - I honestly do not have an immediate answer, it is not obvious to me from the output.
i used wicd with my eeepc and i got some problems; btw, NM does'nt work at all in my eeepc so... :)

in my laptop, NM work fine; but i'd like to connect using init.d scripts when i connect to net i know

btw, now even my connection at work does'nt work anymore x_x
i was used to connect with wpa_supplicant with this configuration:
conf.d/net
Code:

 modules_eth0=( "wpa_supplicant")
 wpa_supplicant_eth0="-Dwired" # For generic wired
# ETH0
 config_eth0=( "dhcp" )
 dhcpcd_eth0="-N"

wpa_supplicant
Code:

network={
        key_mgmt=IEEE8021X
        eap=PEAP
        phase1="peaplabel=1"
        phase2="auth=MSCHAPV2"
        identity="XXXXXX"
        password="YYYYYYY"
        priority=6
        }


x_x
i had to switch to NM or i can't work ;_;
where's the problem?

:(

as soon as possible i try to manually start wpa on eth0 and check for errors...

cach0rr0 wrote:

Also, you said you wish to connect to "Uairless-di-Fastuebb", however from your .conf that looks to be the *second* one, and also appears to be using WPA and not WEP.
For WPA, all you should need is this:

Code:

network={
ssid="crackme"
scan_ssid=1
key_mgmt=WPA-PSK
psk="mypassword"
}


Until we can get the right settings for wpa_supplicant.conf, the init script for net.wlan0 is not going to function.
Ok.
so i need to remove/comment it from conf.d/net?
i'm a bit confused x_x

Edit
ok this is the error output
Code:

# wpa_supplicant -Dwired -i eth0 -c /etc/wpa_supplicant/wpa_supplicant.conf
Associated with 01:80:c2:00:00:03
CTRL-EVENT-EAP-STARTED EAP authentication started
CTRL-EVENT-EAP-PROPOSED-METHOD vendor=0 method=25
CTRL-EVENT-EAP-METHOD EAP vendor 0 method 25 (PEAP) selected
CTRL-EVENT-EAP-PEER-CERT depth=1 subject='/C=IT/ST=Lazio/L=Roma/O=Postecom S.p.A./OU=Netsecurity/CN=CAparacetamolo2/emailAddress=netsecurity@postecom.it'
CTRL-EVENT-EAP-PEER-CERT depth=1 subject='/C=IT/ST=Lazio/L=Roma/O=Postecom S.p.A./OU=Netsecurity/CN=CAparacetamolo2/emailAddress=netsecurity@postecom.it'
CTRL-EVENT-EAP-PEER-CERT depth=0 subject='/C=IT/ST=Lazio/O=Postecom S.p.A./OU=Netsecurity/CN=paracetamolo2.cs.poste.it/emailAddress=netsecurity@postecom.it'
CTRL-EVENT-EAP-PEER-CERT depth=0 subject='/C=IT/ST=Lazio/O=Postecom S.p.A./OU=Netsecurity/CN=paracetamolo2.cs.poste.it/emailAddress=netsecurity@postecom.it'
SSL: SSL3 alert: write (local SSL3 detected an error):fatal:decrypt error
OpenSSL: openssl_handshake - SSL_connect error:04091068:rsa routines:INT_RSA_VERIFY:bad signature
OpenSSL: pending error: error:1408D07B:SSL routines:SSL3_GET_KEY_EXCHANGE:bad signature

CTRL-EVENT-EAP-FAILURE EAP authentication failed
btw, with NM i connect correctly, so username/password is correct... x_x
Back to top
View user's profile Send private message
divago
Tux's lil' helper
Tux's lil' helper


Joined: 04 Jun 2010
Posts: 84

PostPosted: Wed Mar 02, 2011 10:39 am    Post subject: Reply with quote

Hi all
i changed topic name 'cause now i got a different problem BUT it's all linked together so i don't whanna start a new topic :)

i bought a new router so i made some little change to conf.d/net scripts but still wpa does'nt work

i did this change to wpa_supplicant.conf:
Code:

ap_scan=1
#ap_scan=0
ctrl_interface=/var/run/wpa_supplicant
ctrl_interface_group=root

network={
        key_mgmt=IEEE8021X
        eap=PEAP
        phase1="peaplabel=1"
        phase2="auth=MSCHAPV2"
        identity="fcavallin"
        password="MySecurePassword"
        priority=6
        }

network={
        ssid="Senzafili"
        scan_ssid=1
        key_mgmt=WPA-PSK
        psk="AnotherSecurePassword"
        priority=2
        }


and launched manually wpa_supplicant with this command:
Code:


# wpa_supplicant -Dwext -i wlan0 -c /etc/wpa_supplicant/wpa_supplicant.conf
Trying to associate with 74:ea:3a:bc:be:a0 (SSID='Senzafili' freq=2452 MHz)
Associated with 74:ea:3a:bc:be:a0
CTRL-EVENT-EAP-STARTED EAP authentication started
CTRL-EVENT-EAP-FAILURE EAP authentication failed
Authentication with 74:ea:3a:bc:be:a0 timed out.
CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=0
(it loop the "authentication failed" message...)
password is correct, 'cause i connect without problem with Network Manager

still, even my eth0 configuration for work does'nt work anymore (and i did'nt change anything)
only things i changed is an emerge -upv wpa_supplicant to get newest version

why i can't use wpa_supplicant anymore??
Back to top
View user's profile Send private message
divago
Tux's lil' helper
Tux's lil' helper


Joined: 04 Jun 2010
Posts: 84

PostPosted: Sun Mar 06, 2011 2:23 pm    Post subject: Reply with quote

hi all, me again, hoping for someone to help me :)
now i used the -d option to get extra debug info

this the results, but honestly i really don't know the problem
the main problem is, ofc, i could'nt connect anymore to wired lan at work ant this is the main problem x_x
btw, it could be tied 'cause wired (at work) and wireless (at home) get same results (authentication failure, dunno why... maybe they canged something in wpa_supplicant sintax??)

here's the debug; it's "cutted" to 200 lines 'cause thereafter it goes loop with the "new scan" results...
Code:

Initializing interface 'wlan0' conf '/etc/wpa_supplicant/wpa_supplicant.conf' driver 'wext' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' -> '/etc/wpa_supplicant/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant/wpa_supplicant.conf'
ap_scan=1
ctrl_interface='/var/run/wpa_supplicant'
ctrl_interface_group='root'
Priority group 6
   id=0 ssid=''
Priority group 2
   id=1 ssid='Senzafili'
WEXT: cfg80211-based driver detected
SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf
  capabilities: key_mgmt 0xf enc 0xf flags 0x0
netlink: Operstate: linkmode=1, operstate=5
Own MAC address: 00:24:2c:16:b3:41
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_countermeasures
RSN: flushing PMKID list in the driver
Setting scan request: 0 sec 100000 usec
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: Supplicant port status: Unauthorized
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: Supplicant port status: Unauthorized
EAPOL: Supplicant port status: Unauthorized
Using existing control interface directory.
ctrl_interface_group=0 (from group name 'root')
Added interface wlan0
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b1a len=8
State: DISCONNECTED -> SCANNING
Scan SSID - hexdump_ascii(len=9):
     53 65 6e 7a 61 66 69 6c 69                        Senzafili       
Starting AP scan for specific SSID(s)
Scan requested (ret=0) - scan timeout 5 seconds
EAPOL: disable timer tick
EAPOL: Supplicant port status: Unauthorized
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b19 len=8
Received 4033 bytes of scan results (10 BSSes)
BSS: Start scan result update 1
BSS: Add new id 0 BSSID 74:ea:3a:bc:be:a0 SSID 'Senzafili'
BSS: Add new id 1 BSSID 00:1d:8b:47:88:a8 SSID 'Uairless-di-Fastuebb'
BSS: Add new id 2 BSSID 5c:33:8e:0f:85:a4 SSID 'Alice-35898276'
BSS: Add new id 3 BSSID 00:1d:8b:49:2d:60 SSID 'FASTWEB-1-001D8B492D60'
BSS: Add new id 4 BSSID 00:1c:a2:c9:d7:f0 SSID 'Alice-18113139'
BSS: Add new id 5 BSSID 00:22:6b:ff:f0:cd SSID 'DaViDo'
BSS: Add new id 6 BSSID 00:03:6f:3d:06:4f SSID ''
BSS: Add new id 7 BSSID 00:1b:2f:aa:52:d0 SSID 'NETGEAR'
BSS: Add new id 8 BSSID 00:0c:f6:2f:fc:19 SSID 'Sitecom'
BSS: Add new id 9 BSSID 00:1c:10:91:4f:01 SSID 'linksys'
New scan results available
Selecting BSS from priority group 6
Try to find WPA-enabled AP
0: 74:ea:3a:bc:be:a0 ssid='Senzafili' wpa_ie_len=22 rsn_ie_len=20 caps=0x11
   skip - SSID mismatch
1: 00:1d:8b:47:88:a8 ssid='Uairless-di-Fastuebb' wpa_ie_len=22 rsn_ie_len=0 caps=0x11
   skip - SSID mismatch
2: 5c:33:8e:0f:85:a4 ssid='Alice-35898276' wpa_ie_len=22 rsn_ie_len=20 caps=0x11
   skip - SSID mismatch
3: 00:1d:8b:49:2d:60 ssid='FASTWEB-1-001D8B492D60' wpa_ie_len=22 rsn_ie_len=0 caps=0x11
   skip - SSID mismatch
4: 00:1c:a2:c9:d7:f0 ssid='Alice-18113139' wpa_ie_len=24 rsn_ie_len=0 caps=0x11
   skip - SSID mismatch
5: 00:22:6b:ff:f0:cd ssid='DaViDo' wpa_ie_len=26 rsn_ie_len=24 caps=0x10
   skip - SSID mismatch
6: 00:03:6f:3d:06:4f ssid='' wpa_ie_len=22 rsn_ie_len=0 caps=0x11
   skip - SSID not known
7: 00:1b:2f:aa:52:d0 ssid='NETGEAR' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
8: 00:0c:f6:2f:fc:19 ssid='Sitecom' wpa_ie_len=0 rsn_ie_len=0 caps=0x1
   skip - no WPA/RSN IE
9: 00:1c:10:91:4f:01 ssid='linksys' wpa_ie_len=0 rsn_ie_len=0 caps=0x1
   skip - no WPA/RSN IE
Try to find non-WPA AP
0: 74:ea:3a:bc:be:a0 ssid='Senzafili' wpa_ie_len=22 rsn_ie_len=20 caps=0x11
   selected non-WPA AP 74:ea:3a:bc:be:a0 ssid='Senzafili'
Trying to associate with 74:ea:3a:bc:be:a0 (SSID='Senzafili' freq=2452 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
WPA: clearing AP WPA IE
WPA: clearing AP RSN IE
WPA: clearing own WPA/RSN IE
No keys have been configured - skip key clearing
State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
netlink: Operstate: linkmode=-1, operstate=5
wpa_driver_wext_associate
wpa_driver_wext_set_drop_unencrypted
wpa_driver_wext_set_psk
Setting authentication timeout: 10 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - EAP fail=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - portControl=Auto
EAPOL: Supplicant port status: Unauthorized
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b1a len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b04 len=12
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b1a len=17
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8c08 len=47
AssocResp IE wireless event - hexdump(len=39): 01 08 82 84 8b 0c 12 96 18 24 32 04 30 48 60 6c dd 09 00 03 7f 01 01 00 00 ff 7f dd 0a 00 03 7f 04 01 00 00 00 40 00
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 74:ea:3a:bc:be:a0
Association info event
resp_ies - hexdump(len=39): 01 08 82 84 8b 0c 12 96 18 24 32 04 30 48 60 6c dd 09 00 03 7f 01 01 00 00 ff 7f dd 0a 00 03 7f 04 01 00 00 00 40 00
State: ASSOCIATING -> ASSOCIATED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
netlink: Operstate: linkmode=-1, operstate=5
Associated to a new BSS: BSSID=74:ea:3a:bc:be:a0
No keys have been configured - skip key clearing
Associated with 74:ea:3a:bc:be:a0
WPA: Association event - clear replay counter
WPA: Clear old PTK
EAPOL: External notification - portEnabled=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - portValid=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: enable timer tick
EAPOL: SUPP_BE entering state IDLE
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
Setting authentication timeout: 10 sec 0 usec
Cancelling scan request
EAPOL: startWhen --> 0
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: txStart
TX EAPOL: dst=74:ea:3a:bc:be:a0
RX EAPOL from 74:ea:3a:bc:be:a0
Setting authentication timeout: 70 sec 0 usec
EAPOL: Received EAP-Packet frame
EAPOL: SUPP_PAE entering state RESTART
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
EAPOL: SUPP_PAE entering state AUTHENTICATING
EAPOL: SUPP_BE entering state REQUEST
EAPOL: getSuppRsp
EAP: EAP entering state RECEIVED
EAP: Received EAP-Request id=186 method=1 vendor=0 vendorMethod=0
EAP: EAP entering state IDENTITY
CTRL-EVENT-EAP-STARTED EAP authentication started
EAP: EAP-Request Identity data - hexdump_ascii(len=0):
EAP: using real identity - hexdump_ascii(len=9):
     66 63 61 76 61 6c 6c 69 6e                        fcavallin       
EAP: EAP entering state SEND_RESPONSE
EAP: EAP entering state IDLE
EAPOL: SUPP_BE entering state RESPONSE
EAPOL: txSuppRsp
TX EAPOL: dst=74:ea:3a:bc:be:a0
EAPOL: SUPP_BE entering state RECEIVE
RX EAPOL from 74:ea:3a:bc:be:a0
EAPOL: Received EAP-Packet frame
EAPOL: SUPP_BE entering state REQUEST
EAPOL: getSuppRsp
EAP: EAP entering state RECEIVED
EAP: Received EAP-Failure
EAP: EAP entering state FAILURE
CTRL-EVENT-EAP-FAILURE EAP authentication failed
EAPOL: SUPP_PAE entering state HELD
EAPOL: Supplicant port status: Unauthorized
EAPOL: SUPP_BE entering state RECEIVE
EAPOL: SUPP_BE entering state FAIL
EAPOL: SUPP_BE entering state IDLE
EAPOL authentication completed unsuccessfully
Setting authentication timeout: 2 sec 0 usec
Authentication with 74:ea:3a:bc:be:a0 timed out.
Added BSSID 74:ea:3a:bc:be:a0 into blacklist
wpa_driver_wext_disassociate
No keys have been configured - skip key clearing
State: ASSOCIATED -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
netlink: Operstate: linkmode=-1, operstate=5
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: Supplicant port status: Unauthorized
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - portValid=0
EAPOL: Supplicant port status: Unauthorized
Setting scan request: 0 sec 0 usec
State: DISCONNECTED -> SCANNING
Starting AP scan for wildcard SSID
Scan requested (ret=0) - scan timeout 30 seconds
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:00:00:00:00:00
Disassociation notification
Added BSSID 00:00:00:00:00:00 into blacklist
CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=0
Disconnect event - remove keys
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
State: SCANNING -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
netlink: Operstate: linkmode=-1, operstate=5
EAPOL: External notification - portEnabled=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - portValid=0
EAPOL: Supplicant port status: Unauthorized
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b1a len=8
EAPOL: Supplicant port status: Unauthorized
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b19 len=8
Scan results did not fit - trying larger buffer (8192 bytes)
Received 5742 bytes of scan results (14 BSSes)
BSS: Start scan result update 2
BSS: Add new id 10 BSSID 00:03:6f:3d:06:4d SSID ''
BSS: Add new id 11 BSSID 00:21:96:28:4a:c8 SSID 'FASTWEB-1-002196284AC0'
BSS: Add new id 12 BSSID 00:16:01:e6:bb:a8 SSID 'AirStation'
BSS: Add new id 13 BSSID 00:03:6f:3d:06:4c SSID 'FASTWEB00036F3D0644'


please, somebody help me :)
Back to top
View user's profile Send private message
cach0rr0
Bodhisattva
Bodhisattva


Joined: 13 Nov 2008
Posts: 4123
Location: Houston, Republic of Texas

PostPosted: Sun Mar 06, 2011 11:36 pm    Post subject: Reply with quote

I'll have to have a good hard think about the wireless one

but for wired, there isn't really any need to try and mess with wpa_supplicant

If you want to manage it via init scripts, add this:

Code:

config_eth0=( "dhcp" )


to your /etc/conf.d/net, and whenever you want to start your wired networking, /etc/init.d/net.eth0 start

if you're happy to type a few commands to manually bring up eth0

Code:

ifconfig eth0 up
dhcpcd eth0


There just shouldn't be any reason wired doesn't work with the above steps, unless for some reason dhcpcd is an older build that is incompatible with your current kernel OR there are still pieces of networkmanager cruft left on this box that are causing problems (it tends to try and do a complete takeover, and redo things in a less than transparent fashion - this is why I eventually got rid of it)
_________________
Lost configuring your system?
dump lspci -n here | see Pappy's guide | Link Stash
Back to top
View user's profile Send private message
Display posts from previous:   
Reply to topic    Gentoo Forums Forum Index Networking & Security All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum