Gentoo Forums
Gentoo Forums
Gentoo Forums
Quick Search: in
aiuto wpa_supplicat[RISOLTO]
View unanswered posts
View posts from last 24 hours
View posts from last 7 days

 
Reply to topic    Gentoo Forums Forum Index Forum italiano (Italian)
View previous topic :: View next topic  
Author Message
mattylux
Apprentice
Apprentice


Joined: 19 Jul 2008
Posts: 240
Location: bologna

PostPosted: Wed Apr 08, 2009 8:54 am    Post subject: aiuto wpa_supplicat[RISOLTO] Reply with quote

ciao ora che sono tutto apposto vorrei connettermi con il wifi della rete universitaria qui di Bologna..
questo e il mio. /etc/wpa_supplicant/wpa_supplicant.conf

Code:
ctrl_interface=/var/run/wpa_supplicant
ctrl_interface_group=0
{
network={
        key_mgmt=NONE
        priority=-9999999
}


network={
    ssid="hot spot wifi iperbole URP"
    key_mgmt=NONE
    wep_key0="123412341234"
}

network={
    ssid="IPERBOLE_WIRELESS_V_2"
    key_mgmt=NONE
    wep_key0="1234"

}



e questo e il mio /etc/conf.d/net

Code:

dns_domain_eth0="*SE*"



config_eth0=( "192.168.0.2/24" )
config_eth0=( "192.168.0.2 netmask 255.255.255.0" )
modules_wlan0=( "wpa_supplicant" )
wpa_supplicant_wlan0="-Dwext"


avrei biso di una mano per configurare bene la rete vi do anche la mia scheda wireless

Code:
bt ~ # lspci | grep Wireless
02:04.0 Network controller: Intel Corporation PRO/Wireless 2200BG Network Connection (
rev 05)


e poi ho rilevato anche questo tipo di errore
Code:
bt ~ # dmesg |tail
ext3_orphan_cleanup: deleting unreferenced inode 182715
EXT3-fs: hda7: 3 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
b44: eth1: BUG!  Timeout waiting for bit 00000002 of register 42c to clear.
[drm] Initialized drm 1.1.0 20060810
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 18
[drm] Initialized i915 1.6.0 20060119 on minor 0
ipw2200: Firmware error detected.  Restarting.
ipw2200: Firmware error detected.  Restarting.


spero che potrete darmi una mano per risolvere qusto problema cosi posso installare xorg-x11 e xfce4
_________________
persempre gentoo
il mio progetto in fase di lavoro
Http://stradedicarta.netsons.org


Last edited by mattylux on Wed Apr 08, 2009 5:31 pm; edited 1 time in total
Back to top
View user's profile Send private message
Peach
Advocate
Advocate


Joined: 08 Mar 2003
Posts: 3686
Location: London, UK

PostPosted: Wed Apr 08, 2009 11:03 am    Post subject: Reply with quote

potresti postare l'output di
Code:
lspci -vv

relativo esclusivamente alla scheda di rete wifi?
_________________
Gentoo user since 2004.
"It's all fun and games, until someone loses an eye" - mom
Back to top
View user's profile Send private message
Cazzantonio
Bodhisattva
Bodhisattva


Joined: 20 Mar 2004
Posts: 4486
Location: Somewere around the world

PostPosted: Wed Apr 08, 2009 11:10 am    Post subject: Reply with quote

Tranquillo, lo faceva anche la mia scheda. Ho risolto acquistandone una nuova su ebay...
E' un problema hardware.

Comunque ti consiglio l'ottimo wicd per gestire le connessioni wireless. Ti evita il problema di dover configurare ogni volta daccapo wpa_supplicant.
_________________
Any man's death diminishes me, because I am involved in mankind, and therefore never send to know for whom the bell tolls; it tolls for thee
-John Donne
Back to top
View user's profile Send private message
Peach
Advocate
Advocate


Joined: 08 Mar 2003
Posts: 3686
Location: London, UK

PostPosted: Wed Apr 08, 2009 11:27 am    Post subject: Reply with quote

Cazzantonio wrote:
Tranquillo, lo faceva anche la mia scheda. Ho risolto acquistandone una nuova su ebay...
E' un problema hardware.

Comunque ti consiglio l'ottimo wicd per gestire le connessioni wireless. Ti evita il problema di dover configurare ogni volta daccapo wpa_supplicant.

e non hai provato usando mac80211 ? te lo dico perché anche la mia aveva iniziato a fare questi scherzi.. cmq vedremo, aspetto che mattylux posti
_________________
Gentoo user since 2004.
"It's all fun and games, until someone loses an eye" - mom
Back to top
View user's profile Send private message
mattylux
Apprentice
Apprentice


Joined: 19 Jul 2008
Posts: 240
Location: bologna

PostPosted: Wed Apr 08, 2009 1:30 pm    Post subject: Reply with quote

Code:
bt / # lspci -vv
00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 03)
        Subsystem: Hewlett-Packard Company NX6110/NC6120
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
        Latency: 0
        Capabilities: [e0] Vendor Specific Information <?>

00:02.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03) (prog-if 00 [VGA controller])
        Subsystem: Hewlett-Packard Company NX6110/NC6120
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin A routed to IRQ 18
        Region 0: Memory at d0400000 (32-bit, non-prefetchable) [size=512K]
        Region 1: I/O ports at 7000 [size=8]
        Region 2: Memory at c0000000 (32-bit, prefetchable) [size=256M]
        Region 3: Memory at d0480000 (32-bit, non-prefetchable) [size=256K]
        Expansion ROM at <unassigned> [disabled]
        Capabilities: [d0] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03)
        Subsystem: Hewlett-Packard Company NX6110/NC6120
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Region 0: Memory at d0500000 (32-bit, non-prefetchable) [size=512K]
        Capabilities: [d0] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03) (prog-if 00 [UHCI])
        Subsystem: Hewlett-Packard Company NX6110/NC6120
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin A routed to IRQ 19
        Region 4: I/O ports at 2000 [size=32]

00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 03) (prog-if 00 [UHCI])
        Subsystem: Hewlett-Packard Company NX6110/NC6120
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin B routed to IRQ 20
        Region 4: I/O ports at 2020 [size=32]

00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 03) (prog-if 00 [UHCI])
        Subsystem: Hewlett-Packard Company NX6110/NC6120
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin C routed to IRQ 17
        Region 4: I/O ports at 2040 [size=32]

00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 03) (prog-if 00 [UHCI])
        Subsystem: Hewlett-Packard Company NX6110/NC6120
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin D routed to IRQ 21
        Region 4: I/O ports at 2060 [size=32]

00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 03) (prog-if 20 [EHCI])
        Subsystem: Hewlett-Packard Company NX6110/NC6120
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin A routed to IRQ 19
        Region 0: Memory at d0580000 (32-bit, non-prefetchable) [size=1K]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [58] Debug port: BAR=1 offset=00a0

00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d3) (prog-if 01 [Subtractive decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Bus: primary=00, secondary=02, subordinate=06, sec-latency=32
        I/O behind bridge: 00003000-00003fff
        Memory behind bridge: d0000000-d03fffff
        Prefetchable memory behind bridge: 0000000020000000-0000000023ffffff
        Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [50] Subsystem: Hewlett-Packard Company NX6110/NC6120

00:1e.2 Multimedia audio controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller (rev 03)
        Subsystem: Hewlett-Packard Company NX6110/NC6120
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin A routed to IRQ 22
        Region 0: I/O ports at 2100 [size=256]
        Region 1: I/O ports at 2200 [size=64]
        Region 2: Memory at d0581000 (32-bit, non-prefetchable) [size=512]
        Region 3: Memory at d0582000 (32-bit, non-prefetchable) [size=256]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:1e.3 Modem: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Modem Controller (rev 03) (prog-if 00 [Generic])
        Subsystem: Hewlett-Packard Company NX6110/NC6120
        Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Interrupt: pin B routed to IRQ 16
        Region 0: I/O ports at 2400 [size=256]
        Region 1: I/O ports at 2500 [size=128]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 03)
        Subsystem: Hewlett-Packard Company NX6110/NC6120
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0

00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 03) (prog-if 8a [Master SecP PriP])
        Subsystem: Hewlett-Packard Company NX6110/NC6120
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin A routed to IRQ 18
        Region 0: I/O ports at 01f0 [size=8]
        Region 1: I/O ports at 03f4
        Region 2: I/O ports at 0170 [size=8]
        Region 3: I/O ports at 0374
        Region 4: I/O ports at 2580 [size=16]

00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller (rev 03)
        Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Interrupt: pin B routed to IRQ 20
        Region 4: I/O ports at 1200 [size=32]

02:04.0 Network controller: Intel Corporation PRO/Wireless 2200BG Network Connection (rev 05)
        Subsystem: Hewlett-Packard Company Compaq nw8240/nx8220
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 64 (750ns min, 6000ns max), Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 22
        Region 0: Memory at d0000000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [dc] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=1 PME-

02:06.0 CardBus bridge: Texas Instruments PCIxx21/x515 Cardbus Controller
        Subsystem: Hewlett-Packard Company NX6110/NC6120
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 168, Cache Line Size: 128 bytes
        Interrupt: pin A routed to IRQ 17
        Region 0: Memory at d0001000 (32-bit, non-prefetchable) [size=4K]
        Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
        Memory window 0: 20000000-23fff000 (prefetchable)
        Memory window 1: 24000000-27fff000
        I/O window 0: 00003000-000030ff
        I/O window 1: 00003400-000034ff
        BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
        16-bit legacy interface ports at 0001

02:06.2 FireWire (IEEE 1394): Texas Instruments OHCI Compliant IEEE 1394 Host Controller (prog-if 10 [OHCI])
        Subsystem: Hewlett-Packard Company NX6110/NC6120
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 64 (500ns min, 1000ns max), Cache Line Size: 64 bytes
        Interrupt: pin C routed to IRQ 16
        Region 0: Memory at d0002000 (32-bit, non-prefetchable) [size=2K]
        Region 1: Memory at d0004000 (32-bit, non-prefetchable) [size=16K]
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME+

02:0e.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02)
        Subsystem: Hewlett-Packard Company NX6110/NC6120
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 64
        Interrupt: pin A routed to IRQ 18
        Region 0: Memory at d0008000 (32-bit, non-prefetchable) [size=8K]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=2 PME-

_________________
persempre gentoo
il mio progetto in fase di lavoro
Http://stradedicarta.netsons.org
Back to top
View user's profile Send private message
mattylux
Apprentice
Apprentice


Joined: 19 Jul 2008
Posts: 240
Location: bologna

PostPosted: Wed Apr 08, 2009 2:21 pm    Post subject: Reply with quote

allora dite che scarico wicd per far funzionare la rete sto dando un occhiata su google e qui nel forum e ho trovato qualcosa ora o provato ad emergere il pacchetto wicd
cosi; emerge -av wicd
e mi dice di scaricate tutti quese dipendenze (ebuild) da scaricare e compilare...

Code:

bt / # emerge -av wicd

These are the packages that would be merged, in order:

Calculating dependencies... done!
[ebuild  N    ] dev-libs/atk-1.24.0  USE="-debug -doc" 686 kB
[ebuild  N    ] app-text/poppler-0.10.4  USE="-doc" 0 kB
[ebuild  N    ] dev-libs/libusb-0.1.12-r1  USE="-debug -doc" 381 kB
[ebuild  N    ] app-text/build-docbook-catalog-1.4  3 kB
[ebuild  N    ] net-wireless/wireless-tools-29  USE="nls -multicall" 288 kB
[ebuild  N    ] dev-python/pygobject-2.16.1  USE="X -debug -doc -examples" 511 kB
[ebuild  N    ] dev-python/numeric-24.2-r6  USE="-doc -lapack" 727 kB
[ebuild  N    ] dev-util/gtk-doc-am-1.10-r1  395 kB
[ebuild  N    ] x11-libs/pixman-0.12.0  USE="(-altivec) -debug -mmx -sse (-sse2)" 356 kB
[ebuild  N    ] dev-python/pyrex-0.9.4.1  178 kB
[ebuild  N    ] dev-util/gperf-3.0.3  845 kB
[ebuild  N    ] sys-apps/eject-2.1.5-r1  USE="nls" 121 kB
[ebuild  N    ] sys-apps/dmidecode-2.9  48 kB
[ebuild  N    ] sys-fs/device-mapper-1.02.24-r1  USE="(-selinux)" 189 kB
[ebuild  N    ] dev-libs/libxslt-1.1.24-r1  USE="crypt python -debug -examples" 3,286 kB
[ebuild  N    ] app-arch/unzip-5.52-r2  1,114 kB
[ebuild  N    ] x11-libs/cairo-1.8.6-r1  USE="X -cleartype -debug -directfb -doc -glitz -opengl -svg -xcb" 6,462 kB
[ebuild  N    ] app-text/docbook-xsl-stylesheets-1.73.2  1,636 kB
[ebuild  N    ] dev-python/dbus-python-0.82.4  USE="-test" 463 kB
[ebuild  N    ] virtual/poppler-utils-0.10.4  USE="abiword" 0 kB
[ebuild  N    ] sys-apps/usbutils-0.73  USE="zlib -network-cron" 170 kB
[ebuild  N    ] sys-fs/cryptsetup-1.0.5-r1  USE="nls -dynamic (-selinux)" 315 kB
[ebuild  N    ] x11-libs/pango-1.22.4  USE="X -debug -doc" 1,462 kB
[ebuild  N    ] dev-python/pycairo-1.4.12  USE="-examples" 479 kB
[ebuild  N    ] app-text/docbook-xml-dtd-4.2-r1  77 kB
[ebuild  N    ] app-text/xmlto-0.0.18  90 kB
[ebuild  N    ] net-print/cups-1.3.9-r1  USE="X acl dbus pam perl python ssl -avahi -gnutls -java -jpeg -kerberos -ldap -php -png -ppds -samba -slp -static -tiff -xinetd -zeroconf" LINGUAS="-de -en -es -et -fr -he -id -it -ja -pl -sv -zh_TW" 0 kB
[ebuild  N    ] app-text/ghostscript-gpl-8.64-r2  USE="X cups -bindist -cairo -cjk -djvu -gtk -jpeg2k" 43 kB
[ebuild  N    ] virtual/ghostscript-0  0 kB
[ebuild  N    ] x11-libs/gtk+-2.14.7-r2  USE="X cups -debug -doc -jpeg -jpeg2k -tiff -vim-syntax -xinerama" 17,067 kB
[ebuild  N    ] x11-misc/ktsuss-1.4  273 kB
[ebuild  N    ] gnome-base/libglade-2.6.3  USE="-debug -doc" 351 kB
[ebuild  N    ] dev-python/pygtk-2.14.0  USE="X -doc -examples" 2,111 kB
[ebuild  N    ] sys-apps/hal-0.5.11-r8  USE="X crypt -acpi -apm -debug -dell -disk-partition -doc -laptop (-selinux)" 1,260 kB
[ebuild  N    ] app-misc/hal-info-20081219  230 kB
[ebuild  N    ] sys-power/pm-utils-1.2.3-r1  USE="alsa -debug -networkmanager -ntp" VIDEO_CARDS="intel -radeon" 173 kB
[ebuild  N    ] net-misc/wicd-1.5.9-r1  253 kB

Total: 37 packages (37 new), Size of downloads: 42,026 kB

Would you like to merge these packages? [Yes/No]       


che cosa mi conscigliate di fare??? continuo ha scaricare oppure aspetto qualche risposta vostra per magari vedere quale e la cosa milgiore per me perche ci sarebbe anche ndiswrapper che servono i drive per windows apparte che nell'altra partizine ho windowzz e funziona benissimo...
_________________
persempre gentoo
il mio progetto in fase di lavoro
Http://stradedicarta.netsons.org
Back to top
View user's profile Send private message
k01
Arch/Herd Tester
Arch/Herd Tester


Joined: 13 Feb 2008
Posts: 617
Location: Milano

PostPosted: Wed Apr 08, 2009 2:47 pm    Post subject: Reply with quote

Peach wrote:
potresti postare l'output di
Code:
lspci -vv

relativo esclusivamente alla scheda di rete wifi?


mattylux wrote:
Code:
bt / # lspci -vv
00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML..........
.........
.........Status: D0 PME-Enable- DSel=0 DScale=2 PME-


stai diventando il mio idolo...

comunque è normale che ti chieda tutte quelle dipendenze visto che hai installato solo il sistema di base. installa pure, tanto molte di quelle dipendenze le avresti installate comunque più avanti con l'ambiente desktop e tutto il resto
Back to top
View user's profile Send private message
mattylux
Apprentice
Apprentice


Joined: 19 Jul 2008
Posts: 240
Location: bologna

PostPosted: Wed Apr 08, 2009 2:52 pm    Post subject: Reply with quote

ok comunque gentoo e una fikkata...

sara anche complicata nelle sue ma io l'adoro...
_________________
persempre gentoo
il mio progetto in fase di lavoro
Http://stradedicarta.netsons.org
Back to top
View user's profile Send private message
Peach
Advocate
Advocate


Joined: 08 Mar 2003
Posts: 3686
Location: London, UK

PostPosted: Wed Apr 08, 2009 3:41 pm    Post subject: Reply with quote

mattylux wrote:
ok comunque gentoo e una fikkata...

sara anche complicata nelle sue ma io l'adoro...


mi serve sapere: che kernel stai usando, che versione di lspci stai usando e pure l'output di
Code:
grep 80211 /usr/src/linux/.config

se non sai, cerca, sono tutti problemi ampliamente discussi e risolti sia qui che sulla rete.
_________________
Gentoo user since 2004.
"It's all fun and games, until someone loses an eye" - mom
Back to top
View user's profile Send private message
mattylux
Apprentice
Apprentice


Joined: 19 Jul 2008
Posts: 240
Location: bologna

PostPosted: Wed Apr 08, 2009 5:30 pm    Post subject: Reply with quote

ciao raga
ho risolto ora mi riesco a connettere anche con wifi grazie di tutto peach metto risolto anche questa ok??' :D

ciao
_________________
persempre gentoo
il mio progetto in fase di lavoro
Http://stradedicarta.netsons.org
Back to top
View user's profile Send private message
Display posts from previous:   
Reply to topic    Gentoo Forums Forum Index Forum italiano (Italian) All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum