MCP55 network issue(solved)

[Gankfest]

When Gentoo for the first time I get these network errors on startup.
err, eth1 socket address family not supported by protocol
err, eth1 sento: badfile descriptor
err, eth1 timed out
ERROR cannot start netmount as net.eth1 could not start

I have MCP55 ethernet on Asus M2N-SLI Deluxe
I have the marvell PHY drivers set in kernel config
I'm not sure if I have forcedeth mod loaded or need it to be loaded lsmod shows nothing
dmesg | tail says eth1: no IPv6 routers present

any additional info needed just ask, any help would be great as I've been at this all day!
_________________
Gankfest™ (>")> ~*

Everyone has to start somewhere, it depends on where you end up that counts! (>")>

[alex.blackbit]

are you missing some important ip stuff in the kernel?

[Gankfest]

I have these modules loaded with an [*]
device drivers ->networking support
PHY Device support
nforce Ethernet support

forcedeth loads on boot so idk why I can't connect.
_________________
Gankfest™ (>")> ~*

Everyone has to start somewhere, it depends on where you end up that counts! (>")>

[alex.blackbit]

i was not talking about your network interface card drivers, but about ip.
and... [*] does mean it is NOT a module but built-in... if you are talking about make menuconfig, what i assume.

[Gankfest]

The kernel mods are preloaded and idk what you mean by I.P. I followed the handbook on configuring the network as DHCP
_________________
Gankfest™ (>")> ~*

Everyone has to start somewhere, it depends on where you end up that counts! (>")>

[Gankfest]

I can't figure this out been 2 days now. I have forcedeth built into the kernel. My network is dhcp, I don't know what else to do, but my network doesn't start so I can't emerge X or kde. Any help would be fantastic.
_________________
Gankfest™ (>")> ~*

Everyone has to start somewhere, it depends on where you end up that counts! (>")>

[alex.blackbit]

are you making fun of me?
* i tell you to check ip and you answer "i have forecedeth built into the kernel".
* i tell you that [*] means that something is not a module but built into the kernel and you anser "the kernel mods are preloaded".
additionally and complain all the time "why i can't connect...", "i can't figure it out..." that's not useful information.
that you have a dhcp server on your network does not mean that your kernel can live without the protocol that dhcp relies on, tcp/ip.
try to understand the answers you get on the forums.

ip means "internet protocol" and is part of the protocol suite "tcp/ip". for a linux computer to function properly you need support for that in your kernel, and i asked you to check if that's the case on your installation.
in make menuconfig go to Networking, Networking Options, TCP/IP Networking and see if that's checked.

it is indeed possible that this isn't a tcp/ip issue at all, but if you checked when i first advised that, the whole discussion could have been avoided.

regards
alex

[Gankfest]

No I'm trying to mess with you, It was a long day yesterday and I was really tired from working on this issue for so long. The IP/TCP opt is set in the kernel. I switched to the 2.6.19-gentoo-r5 because it worked before, but my network still doesn't boot. I get this error:

err, eth0: timed out
warn, eth0: using ipv4ll address 169.254.217.174
err, eth0: failed to lookup hostname via dns: temp failure in name resolution

the IP/TCP is set in the new kernel, as well as nvidia Ethernet(forcedeth ver. 0.57) which are built in drivers.

the new kernel is set properly in grub and was compiled properly.

dmesg | grep forcedeth shows it is running.

lspci shows eth info as:

00:08.0 bridge: Nvidia Corp mcp55 eth. (rev a2)
00:09.0 bridge: Nvidia Corp mcp55 eth. (rev a2)
I'm using eth0, eth1 is disconnected.

/etc/conf.d/net is set to dhcp using dhcpcd with no dns nontp nonis. I use a smoothwall 3.0 which automatically assign IP addresses.

anything else you need just ask and I'll be glad to post it, I'm really trying to figure this out and have no idea why it's not working, and I'm not trying to mess with you or be mean. Thanx for the help!
_________________
Gankfest™ (>")> ~*

Everyone has to start somewhere, it depends on where you end up that counts! (>")>

[kmike]

Hi

I'm experiencing similar problem. I get:

ERROR cannot start netmount as net.eth0 could not start

at boot. I'm pretty sure it's connected with fact, I didn't build forcedeth into my kernel. The problem is, i don't have "nforce support" in menuconfig. Is it dependand on some other options?

The kernel is 2.6.24-r3 gentoo-sources.

lspci output:

[Erulabs]

kmike: We arn't going to do your work for you.

[Gankfest]

how can i copy all that info to usbstick in gentoo tect, so i can post all my info.
_________________
Gankfest™ (>")> ~*

Everyone has to start somewhere, it depends on where you end up that counts! (>")>

[Erulabs]

[Gankfest]

[Erulabs]

copy is "cp".


a smoothwall is a router. You're beginning to wear on my patience.
_________________
No more things should be presumed to exist than are absolutely necessary. Or really cool.

[Gankfest]

It's setup properly, I've tried going through the modem to get an address from comcast. that doesn't work either. I installed this last year on 2.6.19 with no problems. thats why I want to know how to post the .config file, lspci, etc.. because something might be missing that isn't listed in the wiki guides, handbook, etc...

I mounted the usb like so:
mkdir /mnt/usb
mount -t vfat /dev/sdc1 /mnt/usb
cp /mnt/usb /usr/src/linux/.config
says cp: omitting directory /mnt/usb
_________________
Gankfest™ (>")> ~*

Everyone has to start somewhere, it depends on where you end up that counts! (>")>

[Erulabs]

"cp -R" for 'recursive copy'. 'recursive' implies it will navigate directories.

Also, cp works the other way around: "cp file copyoffile". Or in your case "cp .config /place/where/a/copy/should/go"
_________________
No more things should be presumed to exist than are absolutely necessary. Or really cool.

[Gankfest]

heres my .config file:

#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.19-gentoo-r5
# Mon Mar 31 00:37:07 2008
#
CONFIG_X86_64=y
CONFIG_64BIT=y
CONFIG_X86=y
CONFIG_ZONE_DMA32=y
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_SEMAPHORE_SLEEPERS=y
CONFIG_MMU=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_X86_CMPXCHG=y
CONFIG_EARLY_PRINTK=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
CONFIG_ARCH_POPULATES_NODE_MAP=y
CONFIG_DMI=y
CONFIG_AUDIT_ARCH=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"

#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32

#
# General setup
#
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
# CONFIG_IPC_NS is not set
CONFIG_POSIX_MQUEUE=y
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_TASKSTATS is not set
# CONFIG_UTS_NS is not set
# CONFIG_AUDIT is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
# CONFIG_CPUSETS is not set
# CONFIG_RELAY is not set
CONFIG_INITRAMFS_SOURCE=""
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
# CONFIG_EMBEDDED is not set
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS=y
CONFIG_KALLSYMS_ALL=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SHMEM=y
CONFIG_SLAB=y
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
# CONFIG_SLOB is not set

#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_KMOD=y
CONFIG_STOP_MACHINE=y

#
# Block layer
#
CONFIG_BLOCK=y
CONFIG_LBD=y
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set

#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
# CONFIG_IOSCHED_AS is not set
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
# CONFIG_DEFAULT_AS is not set
# CONFIG_DEFAULT_DEADLINE is not set
CONFIG_DEFAULT_CFQ=y
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="cfq"

#
# Processor type and features
#
CONFIG_X86_PC=y
# CONFIG_X86_VSMP is not set
CONFIG_MK8=y
# CONFIG_MPSC is not set
# CONFIG_GENERIC_CPU is not set
CONFIG_X86_L1_CACHE_BYTES=64
CONFIG_X86_L1_CACHE_SHIFT=6
CONFIG_X86_INTERNODE_CACHE_BYTES=64
CONFIG_X86_TSC=y
CONFIG_X86_GOOD_APIC=y
# CONFIG_MICROCODE is not set
CONFIG_X86_MSR=y
CONFIG_X86_CPUID=y
CONFIG_X86_IO_APIC=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_MTRR=y
CONFIG_SMP=y
# CONFIG_SCHED_SMT is not set
CONFIG_SCHED_MC=y
# CONFIG_PREEMPT_NONE is not set
CONFIG_PREEMPT_VOLUNTARY=y
# CONFIG_PREEMPT is not set
CONFIG_PREEMPT_BKL=y
CONFIG_NUMA=y
CONFIG_K8_NUMA=y
CONFIG_NODES_SHIFT=6
CONFIG_X86_64_ACPI_NUMA=y
CONFIG_NUMA_EMU=y
CONFIG_ARCH_DISCONTIGMEM_ENABLE=y
CONFIG_ARCH_DISCONTIGMEM_DEFAULT=y
CONFIG_ARCH_SPARSEMEM_ENABLE=y
CONFIG_SELECT_MEMORY_MODEL=y
# CONFIG_FLATMEM_MANUAL is not set
CONFIG_DISCONTIGMEM_MANUAL=y
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_DISCONTIGMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_NEED_MULTIPLE_NODES=y
# CONFIG_SPARSEMEM_STATIC is not set
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_MIGRATION=y
CONFIG_RESOURCES_64BIT=y
CONFIG_HAVE_ARCH_EARLY_PFN_TO_NID=y
CONFIG_OUT_OF_LINE_PFN_TO_PAGE=y
CONFIG_NR_CPUS=32
CONFIG_HOTPLUG_CPU=y
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
CONFIG_HPET_TIMER=y
CONFIG_HPET_EMULATE_RTC=y
CONFIG_IOMMU=y
# CONFIG_CALGARY_IOMMU is not set
CONFIG_SWIOTLB=y
CONFIG_X86_MCE=y
# CONFIG_X86_MCE_INTEL is not set
CONFIG_X86_MCE_AMD=y
# CONFIG_KEXEC is not set
# CONFIG_CRASH_DUMP is not set
CONFIG_PHYSICAL_START=0x200000
CONFIG_SECCOMP=y
# CONFIG_CC_STACKPROTECTOR is not set
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
# CONFIG_HZ_1000 is not set
CONFIG_HZ=250
# CONFIG_REORDER is not set
CONFIG_K8_NB=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_ISA_DMA_API=y
CONFIG_GENERIC_PENDING_IRQ=y

#
# Power management options
#
CONFIG_PM=y
# CONFIG_PM_LEGACY is not set
# CONFIG_PM_DEBUG is not set
# CONFIG_PM_SYSFS_DEPRECATED is not set
CONFIG_SOFTWARE_SUSPEND=y
CONFIG_PM_STD_PARTITION=""
CONFIG_SUSPEND_SMP=y

#
# ACPI (Advanced Configuration and Power Interface) Support
#
CONFIG_ACPI=y
CONFIG_ACPI_SLEEP=y
CONFIG_ACPI_SLEEP_PROC_FS=y
CONFIG_ACPI_SLEEP_PROC_SLEEP=y
CONFIG_ACPI_AC=y
CONFIG_ACPI_BATTERY=y
CONFIG_ACPI_BUTTON=y
# CONFIG_ACPI_VIDEO is not set
# CONFIG_ACPI_HOTKEY is not set
CONFIG_ACPI_FAN=y
# CONFIG_ACPI_DOCK is not set
CONFIG_ACPI_PROCESSOR=y
CONFIG_ACPI_HOTPLUG_CPU=y
CONFIG_ACPI_THERMAL=y
CONFIG_ACPI_NUMA=y
# CONFIG_ACPI_ASUS is not set
# CONFIG_ACPI_IBM is not set
# CONFIG_ACPI_TOSHIBA is not set
CONFIG_ACPI_BLACKLIST_YEAR=0
# CONFIG_ACPI_DEBUG is not set
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_SYSTEM=y
CONFIG_X86_PM_TIMER=y
CONFIG_ACPI_CONTAINER=y
# CONFIG_ACPI_SBS is not set

#
# CPU Frequency scaling
#
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_TABLE=y
CONFIG_CPU_FREQ_DEBUG=y
CONFIG_CPU_FREQ_STAT=y
# CONFIG_CPU_FREQ_STAT_DETAILS is not set
CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
# CONFIG_CPU_FREQ_GOV_POWERSAVE is not set
CONFIG_CPU_FREQ_GOV_USERSPACE=y
CONFIG_CPU_FREQ_GOV_ONDEMAND=y
# CONFIG_CPU_FREQ_GOV_CONSERVATIVE is not set

#
# CPUFreq processor drivers
#
CONFIG_X86_POWERNOW_K8=y
CONFIG_X86_POWERNOW_K8_ACPI=y
# CONFIG_X86_SPEEDSTEP_CENTRINO is not set
CONFIG_X86_ACPI_CPUFREQ=y

#
# shared options
#
CONFIG_X86_ACPI_CPUFREQ_PROC_INTF=y
# CONFIG_X86_SPEEDSTEP_LIB is not set

#
# Bus options (PCI etc.)
#
CONFIG_PCI=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
CONFIG_PCIEPORTBUS=y
CONFIG_PCIEAER=y
CONFIG_PCI_MSI=y
# CONFIG_PCI_DEBUG is not set
# CONFIG_HT_IRQ is not set

#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set

#
# PCI Hotplug Support
#
# CONFIG_HOTPLUG_PCI is not set

#
# Executable file formats / Emulations
#
CONFIG_BINFMT_ELF=y
# CONFIG_BINFMT_MISC is not set
CONFIG_IA32_EMULATION=y
CONFIG_IA32_AOUT=y
CONFIG_COMPAT=y
CONFIG_SYSVIPC_COMPAT=y

#
# Networking
#
CONFIG_NET=y

#
# Networking options
#
# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
# CONFIG_NET_KEY is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_FIB_HASH=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
# CONFIG_IP_PNP_BOOTP is not set
# CONFIG_IP_PNP_RARP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_ARPD is not set
# CONFIG_SYN_COOKIES is not set
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set
# CONFIG_INET_XFRM_TUNNEL is not set
# CONFIG_INET_TUNNEL is not set
# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
# CONFIG_INET_XFRM_MODE_TUNNEL is not set
# CONFIG_INET_XFRM_MODE_BEET is not set
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
CONFIG_IPV6=y
# CONFIG_IPV6_PRIVACY is not set
# CONFIG_IPV6_ROUTER_PREF is not set
# CONFIG_INET6_AH is not set
# CONFIG_INET6_ESP is not set
# CONFIG_INET6_IPCOMP is not set
# CONFIG_IPV6_MIP6 is not set
# CONFIG_INET6_XFRM_TUNNEL is not set
# CONFIG_INET6_TUNNEL is not set
# CONFIG_INET6_XFRM_MODE_TRANSPORT is not set
# CONFIG_INET6_XFRM_MODE_TUNNEL is not set
# CONFIG_INET6_XFRM_MODE_BEET is not set
# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set
CONFIG_IPV6_SIT=y
# CONFIG_IPV6_TUNNEL is not set
# CONFIG_IPV6_MULTIPLE_TABLES is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set

#
# DCCP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_DCCP is not set

#
# SCTP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_SCTP is not set

#
# TIPC Configuration (EXPERIMENTAL)
#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set

#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set

#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_NET_TCPPROBE is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_IEEE80211 is not set

#
# Device Drivers
#

#
# Generic Driver Options
#
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_SYS_HYPERVISOR is not set

#
# Connector - unified userspace <-> kernelspace linker
#
# CONFIG_CONNECTOR is not set

#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set

#
# Parallel port support
#
# CONFIG_PARPORT is not set

#
# Plug and Play support
#
# CONFIG_PNP is not set

#
# Block devices
#
# CONFIG_BLK_DEV_FD is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_SX8 is not set
# CONFIG_BLK_DEV_UB is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=4096
CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
CONFIG_BLK_DEV_INITRD=y
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set

#
# Misc devices
#
# CONFIG_IBM_ASM is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set

#
# ATA/ATAPI/MFM/RLL support
#
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y

#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_IDE_SATA is not set
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
CONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
# CONFIG_BLK_DEV_IDESCSI is not set
# CONFIG_IDE_TASK_IOCTL is not set

#
# IDE chipset support/bugfixes
#
CONFIG_IDE_GENERIC=y
# CONFIG_BLK_DEV_CMD640 is not set
CONFIG_BLK_DEV_IDEPCI=y
# CONFIG_IDEPCI_SHARE_IRQ is not set
# CONFIG_BLK_DEV_OFFBOARD is not set
# CONFIG_BLK_DEV_GENERIC is not set
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_RZ1000 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
CONFIG_BLK_DEV_AMD74XX=y
# CONFIG_BLK_DEV_ATIIXP is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_JMICRON is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_PIIX is not set
# CONFIG_BLK_DEV_IT821X is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_IDE_ARM is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_HD is not set

#
# SCSI device support
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
CONFIG_SCSI_NETLINK=y
# CONFIG_SCSI_PROC_FS is not set

#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=y
# CONFIG_BLK_DEV_SR_VENDOR is not set
CONFIG_CHR_DEV_SG=y
# CONFIG_CHR_DEV_SCH is not set

#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
# CONFIG_SCSI_MULTI_LUN is not set
CONFIG_SCSI_CONSTANTS=y
# CONFIG_SCSI_LOGGING is not set

#
# SCSI Transports
#
CONFIG_SCSI_SPI_ATTRS=y
CONFIG_SCSI_FC_ATTRS=y
# CONFIG_SCSI_ISCSI_ATTRS is not set
CONFIG_SCSI_SAS_ATTRS=y
# CONFIG_SCSI_SAS_LIBSAS is not set

#
# SCSI low-level drivers
#
# CONFIG_ISCSI_TCP is not set
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AACRAID is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
CONFIG_SCSI_AIC79XX=y
CONFIG_AIC79XX_CMDS_PER_DEVICE=32
CONFIG_AIC79XX_RESET_DELAY_MS=4000
# CONFIG_AIC79XX_ENABLE_RD_STRM is not set
# CONFIG_AIC79XX_DEBUG_ENABLE is not set
CONFIG_AIC79XX_DEBUG_MASK=0
# CONFIG_AIC79XX_REG_PRETTY_PRINT is not set
# CONFIG_SCSI_AIC94XX is not set
# CONFIG_SCSI_ARCMSR is not set
CONFIG_MEGARAID_NEWGEN=y
CONFIG_MEGARAID_MM=y
CONFIG_MEGARAID_MAILBOX=y
# CONFIG_MEGARAID_LEGACY is not set
CONFIG_MEGARAID_SAS=y
# CONFIG_SCSI_HPTIOP is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_STEX is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_QLA_FC is not set
# CONFIG_SCSI_QLA_ISCSI is not set
# CONFIG_SCSI_LPFC is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_DEBUG is not set

#
# Serial ATA (prod) and Parallel ATA (experimental) drivers
#
CONFIG_ATA=y
CONFIG_SATA_AHCI=y
# CONFIG_SATA_SVW is not set
# CONFIG_ATA_PIIX is not set
# CONFIG_SATA_MV is not set
CONFIG_SATA_NV=y
# CONFIG_PDC_ADMA is not set
# CONFIG_SATA_QSTOR is not set
# CONFIG_SATA_PROMISE is not set
# CONFIG_SATA_SX4 is not set
# CONFIG_SATA_SIL is not set
# CONFIG_SATA_SIL24 is not set
# CONFIG_SATA_SIS is not set
# CONFIG_SATA_ULI is not set
# CONFIG_SATA_VIA is not set
# CONFIG_SATA_VITESSE is not set
CONFIG_SATA_INTEL_COMBINED=y
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
# CONFIG_PATA_ATIIXP is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_CS5520 is not set
# CONFIG_PATA_CS5530 is not set
# CONFIG_PATA_CYPRESS is not set
# CONFIG_PATA_EFAR is not set
# CONFIG_ATA_GENERIC is not set
# CONFIG_PATA_HPT366 is not set
# CONFIG_PATA_HPT37X is not set
# CONFIG_PATA_HPT3X2N is not set
# CONFIG_PATA_HPT3X3 is not set
# CONFIG_PATA_IT821X is not set
# CONFIG_PATA_JMICRON is not set
# CONFIG_PATA_TRIFLEX is not set
# CONFIG_PATA_MPIIX is not set
# CONFIG_PATA_OLDPIIX is not set
# CONFIG_PATA_NETCELL is not set
# CONFIG_PATA_NS87410 is not set
# CONFIG_PATA_OPTI is not set
# CONFIG_PATA_OPTIDMA is not set
# CONFIG_PATA_PDC_OLD is not set
# CONFIG_PATA_RADISYS is not set
# CONFIG_PATA_RZ1000 is not set
# CONFIG_PATA_SC1200 is not set
# CONFIG_PATA_SERVERWORKS is not set
# CONFIG_PATA_PDC2027X is not set
# CONFIG_PATA_SIL680 is not set
# CONFIG_PATA_SIS is not set
# CONFIG_PATA_VIA is not set
# CONFIG_PATA_WINBOND is not set

#
# Multi-device support (RAID and LVM)
#
CONFIG_MD=y
# CONFIG_BLK_DEV_MD is not set
CONFIG_BLK_DEV_DM=y
# CONFIG_DM_DEBUG is not set
# CONFIG_DM_CRYPT is not set
# CONFIG_DM_SNAPSHOT is not set
# CONFIG_DM_MIRROR is not set
# CONFIG_DM_ZERO is not set
# CONFIG_DM_MULTIPATH is not set
# CONFIG_BLK_DEV_DM_BBR is not set

#
# Fusion MPT device support
#
CONFIG_FUSION=y
CONFIG_FUSION_SPI=y
# CONFIG_FUSION_FC is not set
CONFIG_FUSION_SAS=y
CONFIG_FUSION_MAX_SGE=128
# CONFIG_FUSION_CTL is not set

#
# IEEE 1394 (FireWire) support
#
CONFIG_IEEE1394=y

#
# Subsystem Options
#
# CONFIG_IEEE1394_VERBOSEDEBUG is not set
# CONFIG_IEEE1394_OUI_DB is not set
# CONFIG_IEEE1394_EXTRA_CONFIG_ROMS is not set
# CONFIG_IEEE1394_EXPORT_FULL_API is not set

#
# Device Drivers
#
# CONFIG_IEEE1394_PCILYNX is not set
CONFIG_IEEE1394_OHCI1394=y

#
# Protocol Drivers
#
# CONFIG_IEEE1394_VIDEO1394 is not set
# CONFIG_IEEE1394_SBP2 is not set
# CONFIG_IEEE1394_ETH1394 is not set
# CONFIG_IEEE1394_DV1394 is not set
CONFIG_IEEE1394_RAWIO=y

#
# I2O device support
#
# CONFIG_I2O is not set

#
# Network device support
#
CONFIG_NETDEVICES=y
CONFIG_DUMMY=y
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
CONFIG_TUN=y

#
# ARCnet devices
#
# CONFIG_ARCNET is not set

#
# PHY device support
#
CONFIG_PHYLIB=y

#
# MII PHY device drivers
#
CONFIG_MARVELL_PHY=y
# CONFIG_DAVICOM_PHY is not set
# CONFIG_QSEMI_PHY is not set
# CONFIG_LXT_PHY is not set
# CONFIG_CICADA_PHY is not set
# CONFIG_VITESSE_PHY is not set
# CONFIG_SMSC_PHY is not set
# CONFIG_FIXED_PHY is not set

#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
# CONFIG_CASSINI is not set
# CONFIG_NET_VENDOR_3COM is not set

#
# Tulip family network device support
#
CONFIG_NET_TULIP=y
# CONFIG_DE2104X is not set
CONFIG_TULIP=y
# CONFIG_TULIP_MWI is not set
# CONFIG_TULIP_MMIO is not set
# CONFIG_TULIP_NAPI is not set
# CONFIG_DE4X5 is not set
# CONFIG_WINBOND_840 is not set
# CONFIG_DM9102 is not set
# CONFIG_ULI526X is not set
# CONFIG_HP100 is not set
CONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_AMD8111_ETH is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_B44 is not set
CONFIG_FORCEDETH=y
CONFIG_FORCEDETH_NAPI=y
# CONFIG_DGRS is not set
# CONFIG_EEPRO100 is not set
# CONFIG_E100 is not set
# CONFIG_FEALNX is not set
# CONFIG_NATSEMI is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_8139CP is not set
# CONFIG_8139TOO is not set
# CONFIG_SIS900 is not set
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_VIA_RHINE is not set

#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
# CONFIG_SIS190 is not set
# CONFIG_SKGE is not set
# CONFIG_SKY2 is not set
# CONFIG_SK98LIN is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
# CONFIG_QLA3XXX is not set

#
# Ethernet (10000 Mbit)
#
# CONFIG_CHELSIO_T1 is not set
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
# CONFIG_MYRI10GE is not set

#
# Token Ring devices
#
# CONFIG_TR is not set

#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set

#
# Wan interfaces
#
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
# CONFIG_NET_FC is not set
# CONFIG_SHAPER is not set
CONFIG_NETCONSOLE=y
CONFIG_NETPOLL=y
# CONFIG_NETPOLL_RX is not set
# CONFIG_NETPOLL_TRAP is not set
CONFIG_NET_POLL_CONTROLLER=y

#
# ISDN subsystem
#
# CONFIG_ISDN is not set

#
# Telephony Support
#
# CONFIG_PHONE is not set

#
# Input device support
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set

#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_TSDEV is not set
CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set

#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
# CONFIG_MOUSE_SERIAL is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set

#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
# CONFIG_SERIO_SERPORT is not set
# CONFIG_SERIO_CT82C710 is not set
# CONFIG_SERIO_PCIPS2 is not set
CONFIG_SERIO_LIBPS2=y
# CONFIG_SERIO_RAW is not set
# CONFIG_GAMEPORT is not set

#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_VT_HW_CONSOLE_BINDING is not set
# CONFIG_SERIAL_NONSTANDARD is not set

#
# Serial drivers
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_PCI=y
CONFIG_SERIAL_8250_NR_UARTS=4
CONFIG_SERIAL_8250_RUNTIME_UARTS=4
# CONFIG_SERIAL_8250_EXTENDED is not set

#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_JSM is not set
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256

#
# IPMI
#
# CONFIG_IPMI_HANDLER is not set

#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
CONFIG_HW_RANDOM=y
# CONFIG_HW_RANDOM_INTEL is not set
CONFIG_HW_RANDOM_AMD=y
# CONFIG_HW_RANDOM_GEODE is not set
# CONFIG_NVRAM is not set
CONFIG_RTC=y
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set

#
# Ftape, the floppy tape device driver
#
CONFIG_AGP=y
CONFIG_AGP_AMD64=y
CONFIG_AGP_INTEL=y
# CONFIG_AGP_SIS is not set
# CONFIG_AGP_VIA is not set
# CONFIG_DRM is not set
# CONFIG_MWAVE is not set
# CONFIG_PC8736x_GPIO is not set
CONFIG_RAW_DRIVER=y
CONFIG_MAX_RAW_DEVS=256
CONFIG_HPET=y
# CONFIG_HPET_RTC_IRQ is not set
CONFIG_HPET_MMAP=y
# CONFIG_HANGCHECK_TIMER is not set

#
# TPM devices
#
# CONFIG_TCG_TPM is not set
# CONFIG_TELCLOCK is not set

#
# I2C support
#
CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y

#
# I2C Algorithms
#
CONFIG_I2C_ALGOBIT=y
# CONFIG_I2C_ALGOPCF is not set
# CONFIG_I2C_ALGOPCA is not set

#
# I2C Hardware Bus support
#
# CONFIG_I2C_ALI1535 is not set
# CONFIG_I2C_ALI1563 is not set
# CONFIG_I2C_ALI15X3 is not set
# CONFIG_I2C_AMD756 is not set
# CONFIG_I2C_AMD8111 is not set
# CONFIG_I2C_I801 is not set
# CONFIG_I2C_I810 is not set
# CONFIG_I2C_PIIX4 is not set
CONFIG_I2C_ISA=y
# CONFIG_I2C_NFORCE2 is not set
# CONFIG_I2C_OCORES is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_PROSAVAGE is not set
# CONFIG_I2C_SAVAGE4 is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
# CONFIG_I2C_STUB is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set
# CONFIG_I2C_VOODOO3 is not set
# CONFIG_I2C_PCA_ISA is not set

#
# Miscellaneous I2C Chip support
#
# CONFIG_SENSORS_DS1337 is not set
# CONFIG_SENSORS_DS1374 is not set
CONFIG_SENSORS_EEPROM=y
# CONFIG_SENSORS_PCF8574 is not set
# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set

#
# SPI support
#
# CONFIG_SPI is not set
# CONFIG_SPI_MASTER is not set

#
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set

#
# Hardware Monitoring support
#
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
# CONFIG_SENSORS_ABITUGURU is not set
# CONFIG_SENSORS_ADM1021 is not set
# CONFIG_SENSORS_ADM1025 is not set
# CONFIG_SENSORS_ADM1026 is not set
# CONFIG_SENSORS_ADM1031 is not set
# CONFIG_SENSORS_ADM9240 is not set
CONFIG_SENSORS_K8TEMP=y
# CONFIG_SENSORS_ASB100 is not set
# CONFIG_SENSORS_ATXP1 is not set
# CONFIG_SENSORS_DS1621 is not set
# CONFIG_SENSORS_F71805F is not set
# CONFIG_SENSORS_FSCHER is not set
# CONFIG_SENSORS_FSCPOS is not set
# CONFIG_SENSORS_GL518SM is not set
# CONFIG_SENSORS_GL520SM is not set
# CONFIG_SENSORS_IT87 is not set
# CONFIG_SENSORS_LM63 is not set
# CONFIG_SENSORS_LM75 is not set
# CONFIG_SENSORS_LM77 is not set
# CONFIG_SENSORS_LM78 is not set
# CONFIG_SENSORS_LM80 is not set
# CONFIG_SENSORS_LM83 is not set
# CONFIG_SENSORS_LM85 is not set
# CONFIG_SENSORS_LM87 is not set
# CONFIG_SENSORS_LM90 is not set
# CONFIG_SENSORS_LM92 is not set
# CONFIG_SENSORS_MAX1619 is not set
# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_SIS5595 is not set
# CONFIG_SENSORS_SMSC47M1 is not set
# CONFIG_SENSORS_SMSC47M192 is not set
CONFIG_SENSORS_SMSC47B397=y
# CONFIG_SENSORS_VIA686A is not set
# CONFIG_SENSORS_VT1211 is not set
# CONFIG_SENSORS_VT8231 is not set
# CONFIG_SENSORS_W83781D is not set
# CONFIG_SENSORS_W83791D is not set
# CONFIG_SENSORS_W83792D is not set
# CONFIG_SENSORS_W83L785TS is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
# CONFIG_SENSORS_HDAPS is not set
# CONFIG_HWMON_DEBUG_CHIP is not set

#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set

#
# Digital Video Broadcasting Devices
#
# CONFIG_DVB is not set
# CONFIG_USB_DABUSB is not set

#
# Graphics support
#
CONFIG_FIRMWARE_EDID=y
CONFIG_FB=y
# CONFIG_FB_DDC is not set
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
# CONFIG_FB_MACMODES is not set
# CONFIG_FB_BACKLIGHT is not set
CONFIG_FB_MODE_HELPERS=y
# CONFIG_FB_TILEBLITTING is not set
# CONFIG_FB_CIRRUS is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
# CONFIG_FB_ARC is not set
# CONFIG_FB_ASILIANT is not set
# CONFIG_FB_IMSTT is not set
# CONFIG_FB_VGA16 is not set
CONFIG_FB_VESA=y
CONFIG_FB_VESA_STD=y
# CONFIG_FB_VESA_TNG is not set
CONFIG_VIDEO_SELECT=y
# CONFIG_FB_HGA is not set
# CONFIG_FB_S1D13XXX is not set
CONFIG_FB_NVIDIA=y
CONFIG_FB_NVIDIA_I2C=y
# CONFIG_FB_RIVA is not set
# CONFIG_FB_INTEL is not set
# CONFIG_FB_MATROX is not set
# CONFIG_FB_RADEON is not set
# CONFIG_FB_ATY128 is not set
# CONFIG_FB_ATY is not set
# CONFIG_FB_SAVAGE is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_KYRO is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_GEODE is not set
# CONFIG_FB_VIRTUAL is not set

#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
CONFIG_VGACON_SOFT_SCROLLBACK=y
CONFIG_VGACON_SOFT_SCROLLBACK_SIZE=256
CONFIG_DUMMY_CONSOLE=y
# CONFIG_FRAMEBUFFER_CONSOLE is not set

#
# Logo configuration
#
CONFIG_LOGO=y
# CONFIG_LOGO_LINUX_MONO is not set
# CONFIG_LOGO_LINUX_VGA16 is not set
CONFIG_LOGO_LINUX_CLUT224=y
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set

#
# Speakup console speech
#
# CONFIG_SPEAKUP is not set

#
# Sound
#
CONFIG_SOUND=y

#
# Advanced Linux Sound Architecture
#
CONFIG_SND=y
# CONFIG_SND_SEQUENCER is not set
# CONFIG_SND_MIXER_OSS is not set
# CONFIG_SND_PCM_OSS is not set
# CONFIG_SND_RTCTIMER is not set
# CONFIG_SND_DYNAMIC_MINORS is not set
CONFIG_SND_SUPPORT_OLD_API=y
CONFIG_SND_VERBOSE_PROCFS=y
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set

#
# Generic devices
#
# CONFIG_SND_DUMMY is not set
# CONFIG_SND_MTPAV is not set
# CONFIG_SND_SERIAL_U16550 is not set
# CONFIG_SND_MPU401 is not set

#
# PCI devices
#
# CONFIG_SND_AD1889 is not set
# CONFIG_SND_ALS300 is not set
# CONFIG_SND_ALS4000 is not set
# CONFIG_SND_ALI5451 is not set
# CONFIG_SND_ATIIXP is not set
# CONFIG_SND_ATIIXP_MODEM is not set
# CONFIG_SND_AU8810 is not set
# CONFIG_SND_AU8820 is not set
# CONFIG_SND_AU8830 is not set
# CONFIG_SND_AZT3328 is not set
# CONFIG_SND_BT87X is not set
# CONFIG_SND_CA0106 is not set
# CONFIG_SND_CMIPCI is not set
# CONFIG_SND_CS4281 is not set
# CONFIG_SND_CS46XX is not set
# CONFIG_SND_DARLA20 is not set
# CONFIG_SND_GINA20 is not set
# CONFIG_SND_LAYLA20 is not set
# CONFIG_SND_DARLA24 is not set
# CONFIG_SND_GINA24 is not set
# CONFIG_SND_LAYLA24 is not set
# CONFIG_SND_MONA is not set
# CONFIG_SND_MIA is not set
# CONFIG_SND_ECHO3G is not set
# CONFIG_SND_INDIGO is not set
# CONFIG_SND_INDIGOIO is not set
# CONFIG_SND_INDIGODJ is not set
# CONFIG_SND_EMU10K1 is not set
# CONFIG_SND_EMU10K1X is not set
# CONFIG_SND_ENS1370 is not set
# CONFIG_SND_ENS1371 is not set
# CONFIG_SND_ES1938 is not set
# CONFIG_SND_ES1968 is not set
# CONFIG_SND_FM801 is not set
# CONFIG_SND_HDA_INTEL is not set
# CONFIG_SND_HDSP is not set
# CONFIG_SND_HDSPM is not set
# CONFIG_SND_ICE1712 is not set
# CONFIG_SND_ICE1724 is not set
# CONFIG_SND_INTEL8X0 is not set
# CONFIG_SND_INTEL8X0M is not set
# CONFIG_SND_KORG1212 is not set
# CONFIG_SND_MAESTRO3 is not set
# CONFIG_SND_MIXART is not set
# CONFIG_SND_NM256 is not set
# CONFIG_SND_PCXHR is not set
# CONFIG_SND_RIPTIDE is not set
# CONFIG_SND_RME32 is not set
# CONFIG_SND_RME96 is not set
# CONFIG_SND_RME9652 is not set
# CONFIG_SND_SONICVIBES is not set
# CONFIG_SND_TRIDENT is not set
# CONFIG_SND_VIA82XX is not set
# CONFIG_SND_VIA82XX_MODEM is not set
# CONFIG_SND_VX222 is not set
# CONFIG_SND_YMFPCI is not set

#
# USB devices
#
# CONFIG_SND_USB_AUDIO is not set
# CONFIG_SND_USB_USX2Y is not set

#
# Open Sound System
#
CONFIG_SOUND_PRIME=y
CONFIG_OSS_OBSOLETE_DRIVER=y
# CONFIG_SOUND_BT878 is not set
# CONFIG_SOUND_EMU10K1 is not set
# CONFIG_SOUND_FUSION is not set
# CONFIG_SOUND_ES1371 is not set
CONFIG_SOUND_ICH=y
# CONFIG_SOUND_TRIDENT is not set
# CONFIG_SOUND_MSNDCLAS is not set
# CONFIG_SOUND_MSNDPIN is not set
# CONFIG_SOUND_VIA82CXXX is not set
# CONFIG_SOUND_OSS is not set

#
# USB support
#
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set

#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_BANDWIDTH is not set
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_SUSPEND is not set
# CONFIG_USB_OTG is not set

#
# USB Host Controller Drivers
#
CONFIG_USB_EHCI_HCD=y
# CONFIG_USB_EHCI_SPLIT_ISO is not set
# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
# CONFIG_USB_EHCI_TT_NEWSCHED is not set
# CONFIG_USB_ISP116X_HCD is not set
CONFIG_USB_OHCI_HCD=y
# CONFIG_USB_OHCI_BIG_ENDIAN is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
CONFIG_USB_UHCI_HCD=y
# CONFIG_USB_SL811_HCD is not set

#
# USB Device Class drivers
#
# CONFIG_USB_ACM is not set
# CONFIG_USB_PRINTER is not set

#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#

#
# may also be needed; see USB_STORAGE Help for more information
#
CONFIG_USB_STORAGE=y
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_DATAFAB is not set
# CONFIG_USB_STORAGE_FREECOM is not set
# CONFIG_USB_STORAGE_ISD200 is not set
# CONFIG_USB_STORAGE_DPCM is not set
# CONFIG_USB_STORAGE_USBAT is not set
# CONFIG_USB_STORAGE_SDDR09 is not set
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
# CONFIG_USB_STORAGE_ALAUDA is not set
# CONFIG_USB_STORAGE_KARMA is not set
# CONFIG_USB_LIBUSUAL is not set

#
# USB Input Devices
#
CONFIG_USB_HID=y
CONFIG_USB_HIDINPUT=y
# CONFIG_USB_HIDINPUT_POWERBOOK is not set
# CONFIG_HID_FF is not set
# CONFIG_USB_HIDDEV is not set
# CONFIG_USB_AIPTEK is not set
# CONFIG_USB_WACOM is not set
# CONFIG_USB_ACECAD is not set
# CONFIG_USB_KBTAB is not set
# CONFIG_USB_POWERMATE is not set
# CONFIG_USB_TOUCHSCREEN is not set
# CONFIG_USB_YEALINK is not set
# CONFIG_USB_XPAD is not set
# CONFIG_USB_ATI_REMOTE is not set
# CONFIG_USB_ATI_REMOTE2 is not set
# CONFIG_USB_KEYSPAN_REMOTE is not set
# CONFIG_USB_APPLETOUCH is not set

#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set

#
# USB Network Adapters
#
# CONFIG_USB_CATC is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_USBNET_MII is not set
# CONFIG_USB_USBNET is not set
CONFIG_USB_MON=y

#
# USB port drivers
#

#
# USB Serial Converter support
#
# CONFIG_USB_SERIAL is not set

#
# USB Miscellaneous drivers
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_ADUTUX is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYPRESS_CY7C63 is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_PHIDGET is not set
# CONFIG_USB_IDMOUSE is not set
# CONFIG_USB_FTDI_ELAN is not set
# CONFIG_USB_APPLEDISPLAY is not set
# CONFIG_USB_SISUSBVGA is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_TEST is not set

#
# USB DSL modem support
#

#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set

#
# MMC/SD Card support
#
# CONFIG_MMC is not set

#
# LED devices
#
# CONFIG_NEW_LEDS is not set

#
# LED drivers
#

#
# LED Triggers
#

#
# InfiniBand support
#
# CONFIG_INFINIBAND is not set

#
# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
#
# CONFIG_EDAC is not set

#
# Real Time Clock
#
# CONFIG_RTC_CLASS is not set

#
# DMA Engine support
#
# CONFIG_DMA_ENGINE is not set

#
# DMA Clients
#

#
# DMA Devices
#

#
# Firmware Drivers
#
# CONFIG_EDD is not set
# CONFIG_DELL_RBU is not set
# CONFIG_DCDBAS is not set

#
# File systems
#
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
# CONFIG_EXT2_FS_SECURITY is not set
# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
# CONFIG_EXT3_FS_SECURITY is not set
# CONFIG_EXT4DEV_FS is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
CONFIG_REISERFS_FS=y
# CONFIG_REISERFS_CHECK is not set
# CONFIG_REISERFS_PROC_INFO is not set
CONFIG_REISERFS_FS_XATTR=y
CONFIG_REISERFS_FS_POSIX_ACL=y
# CONFIG_REISERFS_FS_SECURITY is not set
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_QUOTA is not set
CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
CONFIG_AUTOFS4_FS=y
# CONFIG_FUSE_FS is not set
CONFIG_GENERIC_ACL=y

#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
# CONFIG_ZISOFS is not set
CONFIG_UDF_FS=y
CONFIG_UDF_NLS=y

#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
CONFIG_NTFS_FS=y
# CONFIG_NTFS_DEBUG is not set
CONFIG_NTFS_RW=y

#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_PROC_SYSCTL=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
CONFIG_TMPFS_POSIX_ACL=y
CONFIG_HUGETLBFS=y
CONFIG_HUGETLB_PAGE=y
CONFIG_RAMFS=y
# CONFIG_CONFIGFS_FS is not set

#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_SQUASHFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set

#
# Network File Systems
#
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
# CONFIG_NFS_V4 is not set
# CONFIG_NFS_DIRECTIO is not set
CONFIG_NFSD=y
CONFIG_NFSD_V3=y
# CONFIG_NFSD_V3_ACL is not set
# CONFIG_NFSD_V4 is not set
CONFIG_NFSD_TCP=y
CONFIG_ROOT_NFS=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
# CONFIG_9P_FS is not set

#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y

#
# Native Language Support
#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
# CONFIG_NLS_CODEPAGE_850 is not set
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
CONFIG_NLS_ASCII=y
CONFIG_NLS_ISO8859_1=y
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
CONFIG_NLS_ISO8859_15=y
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
CONFIG_NLS_UTF8=y

#
# Instrumentation Support
#
CONFIG_PROFILING=y
CONFIG_OPROFILE=y
CONFIG_KPROBES=y

#
# Kernel hacking
#
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
# CONFIG_PRINTK_TIME is not set
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_MAGIC_SYSRQ=y
CONFIG_UNUSED_SYMBOLS=y
CONFIG_DEBUG_KERNEL=y
CONFIG_LOG_BUF_SHIFT=18
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_MUTEXES is not set
# CONFIG_DEBUG_RWSEMS is not set
# CONFIG_DEBUG_LOCK_ALLOC is not set
# CONFIG_PROVE_LOCKING is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_INFO is not set
CONFIG_DEBUG_FS=y
# CONFIG_DEBUG_VM is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_FRAME_POINTER is not set
CONFIG_UNWIND_INFO=y
CONFIG_STACK_UNWIND=y
# CONFIG_FORCED_INLINING is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_LKDTM is not set
# CONFIG_DEBUG_RODATA is not set
# CONFIG_IOMMU_DEBUG is not set
CONFIG_DEBUG_STACKOVERFLOW=y
# CONFIG_DEBUG_STACK_USAGE is not set

#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set

#
# Cryptographic options
#
# CONFIG_CRYPTO is not set

#
# Library routines
#
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
CONFIG_PLIST=y

this is the log messages. I tried to copy ifconfig and lscpi, but I don't know how!

Mar 31 16:35:41 localhost Linux version 2.6.19-gentoo-r5 (root@localhost) (gcc version 4.1.1 (Gentoo 4.1.1-r3)) #4 SMP Mon Mar 31 00:38:32 Local time zone must be set--see zic
Mar 31 16:35:41 localhost Command line: root=/dev/sda3
Mar 31 16:35:41 localhost BIOS-provided physical RAM map:
Mar 31 16:35:41 localhost BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
Mar 31 16:35:41 localhost BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
Mar 31 16:35:41 localhost BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
Mar 31 16:35:41 localhost BIOS-e820: 0000000000100000 - 000000007fee0000 (usable)
Mar 31 16:35:41 localhost BIOS-e820: 000000007fee0000 - 000000007fee3000 (ACPI NVS)
Mar 31 16:35:41 localhost BIOS-e820: 000000007fee3000 - 000000007fef0000 (ACPI data)
Mar 31 16:35:41 localhost BIOS-e820: 000000007fef0000 - 000000007ff00000 (reserved)
Mar 31 16:35:41 localhost BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)
Mar 31 16:35:41 localhost BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
Mar 31 16:35:41 localhost Entering add_active_range(0, 0, 159) 0 entries of 3200 used
Mar 31 16:35:41 localhost Entering add_active_range(0, 256, 524000) 1 entries of 3200 used
Mar 31 16:35:41 localhost end_pfn_map = 1048576
Mar 31 16:35:41 localhost DMI 2.4 present.
Mar 31 16:35:41 localhost ACPI: RSDP (v002 Nvidia ) @ 0x00000000000f7b70
Mar 31 16:35:41 localhost ACPI: XSDT (v001 Nvidia ASUSACPI 0x42302e31 AWRD 0x00000000) @ 0x000000007fee30c0
Mar 31 16:35:41 localhost ACPI: FADT (v003 Nvidia ASUSACPI 0x42302e31 AWRD 0x00000000) @ 0x000000007feec540
Mar 31 16:35:41 localhost ACPI: SSDT (v001 PTLTD POWERNOW 0x00000001 LTP 0x00000001) @ 0x000000007feec740
Mar 31 16:35:41 localhost ACPI: HPET (v001 Nvidia ASUSACPI 0x42302e31 AWRD 0x00000098) @ 0x000000007feeca80
Mar 31 16:35:41 localhost ACPI: MCFG (v001 Nvidia ASUSACPI 0x42302e31 AWRD 0x00000000) @ 0x000000007feecb00
Mar 31 16:35:41 localhost ACPI: MADT (v001 Nvidia ASUSACPI 0x42302e31 AWRD 0x00000000) @ 0x000000007feec680
Mar 31 16:35:41 localhost ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x03000000) @ 0x0000000000000000
Mar 31 16:35:41 localhost Scanning NUMA topology in Northbridge 24
Mar 31 16:35:41 localhost Number of nodes 1
Mar 31 16:35:41 localhost Node 0 MemBase 0000000000000000 Limit 000000007fee0000
Mar 31 16:35:41 localhost Entering add_active_range(0, 0, 159) 0 entries of 3200 used
Mar 31 16:35:41 localhost Entering add_active_range(0, 256, 524000) 1 entries of 3200 used
Mar 31 16:35:41 localhost NUMA: Using 63 for the hash shift.
Mar 31 16:35:41 localhost Using node hash shift of 63
Mar 31 16:35:41 localhost Bootmem setup node 0 0000000000000000-000000007fee0000
Mar 31 16:35:41 localhost Zone PFN ranges:
Mar 31 16:35:41 localhost DMA 0 -> 4096
Mar 31 16:35:41 localhost DMA32 4096 -> 1048576
Mar 31 16:35:41 localhost Normal 1048576 -> 1048576
Mar 31 16:35:41 localhost early_node_map[2] active PFN ranges
Mar 31 16:35:41 localhost 0: 0 -> 159
Mar 31 16:35:41 localhost 0: 256 -> 524000
Mar 31 16:35:41 localhost On node 0 totalpages: 523903
Mar 31 16:35:41 localhost DMA zone: 56 pages used for memmap
Mar 31 16:35:41 localhost DMA zone: 1692 pages reserved
Mar 31 16:35:41 localhost DMA zone: 2251 pages, LIFO batch:0
Mar 31 16:35:41 localhost DMA32 zone: 7108 pages used for memmap
Mar 31 16:35:41 localhost DMA32 zone: 512796 pages, LIFO batch:31
Mar 31 16:35:41 localhost Normal zone: 0 pages used for memmap
Mar 31 16:35:41 localhost ACPI: PM-Timer IO Port: 0x1008
Mar 31 16:35:41 localhost ACPI: Local APIC address 0xfee00000
Mar 31 16:35:41 localhost ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Mar 31 16:35:41 localhost Processor #0 (Bootup-CPU)
Mar 31 16:35:41 localhost ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Mar 31 16:35:41 localhost Processor #1
Mar 31 16:35:41 localhost ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
Mar 31 16:35:41 localhost ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
Mar 31 16:35:41 localhost ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
Mar 31 16:35:41 localhost IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
Mar 31 16:35:41 localhost ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
Mar 31 16:35:41 localhost ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Mar 31 16:35:41 localhost ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
Mar 31 16:35:41 localhost ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
Mar 31 16:35:41 localhost ACPI: IRQ0 used by override.
Mar 31 16:35:41 localhost ACPI: IRQ2 used by override.
Mar 31 16:35:41 localhost ACPI: IRQ9 used by override.
Mar 31 16:35:41 localhost ACPI: IRQ14 used by override.
Mar 31 16:35:41 localhost ACPI: IRQ15 used by override.
Mar 31 16:35:41 localhost Setting APIC routing to physical flat
Mar 31 16:35:41 localhost ACPI: HPET id: 0x10de8201 base: 0xfefff000
Mar 31 16:35:41 localhost Using ACPI (MADT) for SMP configuration information
Mar 31 16:35:41 localhost Nosave address range: 000000000009f000 - 00000000000a0000
Mar 31 16:35:41 localhost Nosave address range: 00000000000a0000 - 00000000000f0000
Mar 31 16:35:41 localhost Nosave address range: 00000000000f0000 - 0000000000100000
Mar 31 16:35:41 localhost Allocating PCI resources starting at 80000000 (gap: 7ff00000:70100000)
Mar 31 16:35:41 localhost SMP: Allowing 2 CPUs, 0 hotplug CPUs
Mar 31 16:35:41 localhost PERCPU: Allocating 36288 bytes of per cpu data
Mar 31 16:35:41 localhost Built 1 zonelists. Total pages: 515047
Mar 31 16:35:41 localhost Kernel command line: root=/dev/sda3
Mar 31 16:35:41 localhost Initializing CPU#0
Mar 31 16:35:41 localhost PID hash table entries: 4096 (order: 12, 32768 bytes)
Mar 31 16:35:41 localhost Console: colour VGA+ 80x25
Mar 31 16:35:41 localhost Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Mar 31 16:35:41 localhost Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Mar 31 16:35:41 localhost Checking aperture...
Mar 31 16:35:41 localhost CPU 0: aperture @ dda2000000 size 32 MB
Mar 31 16:35:41 localhost Aperture too small (32 MB)
Mar 31 16:35:41 localhost No AGP bridge found
Mar 31 16:35:41 localhost Memory: 2056432k/2096000k available (3297k kernel code, 39180k reserved, 2233k data, 312k init)
Mar 31 16:35:41 localhost Calibrating delay using timer specific routine.. 5631.91 BogoMIPS (lpj=11263839)
Mar 31 16:35:41 localhost Mount-cache hash table entries: 256
Mar 31 16:35:41 localhost CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
Mar 31 16:35:41 localhost CPU: L2 Cache: 1024K (64 bytes/line)
Mar 31 16:35:41 localhost CPU 0/0 -> Node 0
Mar 31 16:35:41 localhost CPU: Physical Processor ID: 0
Mar 31 16:35:41 localhost CPU: Processor Core ID: 0
Mar 31 16:35:41 localhost SMP alternatives: switching to UP code
Mar 31 16:35:41 localhost ACPI: Core revision 20060707
Mar 31 16:35:41 localhost Using local APIC timer interrupts.
Mar 31 16:35:41 localhost result 12560081
Mar 31 16:35:41 localhost Detected 12.560 MHz APIC timer.
Mar 31 16:35:41 localhost SMP alternatives: switching to SMP code
Mar 31 16:35:41 localhost Booting processor 1/2 APIC 0x1
Mar 31 16:35:41 localhost Initializing CPU#1
Mar 31 16:35:41 localhost Calibrating delay using timer specific routine.. 5625.99 BogoMIPS (lpj=11251982)
Mar 31 16:35:41 localhost CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
Mar 31 16:35:41 localhost CPU: L2 Cache: 1024K (64 bytes/line)
Mar 31 16:35:41 localhost CPU 1/1 -> Node 0
Mar 31 16:35:41 localhost CPU: Physical Processor ID: 0
Mar 31 16:35:41 localhost CPU: Processor Core ID: 1
Mar 31 16:35:41 localhost AMD Athlon(tm) 64 X2 Dual Core Processor 5600+ stepping 03
Mar 31 16:35:41 localhost CPU 1: Syncing TSC to CPU 0.
Mar 31 16:35:41 localhost CPU 1: synchronized TSC with CPU 0 (last diff 0 cycles, maxerr 569 cycles)
Mar 31 16:35:41 localhost Brought up 2 CPUs
Mar 31 16:35:41 localhost testing NMI watchdog ... OK.
Mar 31 16:35:41 localhost time.c: Using 25.000000 MHz WALL HPET GTOD HPET timer.
Mar 31 16:35:41 localhost time.c: Detected 2813.456 MHz processor.
Mar 31 16:35:41 localhost migration_cost=323
Mar 31 16:35:41 localhost NET: Registered protocol family 16
Mar 31 16:35:41 localhost ACPI: bus type pci registered
Mar 31 16:35:41 localhost PCI: Using MMCONFIG at f0000000
Mar 31 16:35:41 localhost PCI: No mmconfig possible on device 00:18
Mar 31 16:35:41 localhost pci_get_subsys() called while pci_devices is still empty
Mar 31 16:35:41 localhost ACPI: Interpreter enabled
Mar 31 16:35:41 localhost ACPI: Using IOAPIC for interrupt routing
Mar 31 16:35:41 localhost ACPI: PCI Root Bridge [PCI0] (0000:00)
Mar 31 16:35:41 localhost PCI: Probing PCI hardware (bus 00)
Mar 31 16:35:41 localhost PCI: Transparent bridge - 0000:00:06.0
Mar 31 16:35:41 localhost Boot video device is 0000:07:00.0
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 11 14 15) *0, disabled.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 10 11 14 15) *0, disabled.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 11 14 15) *0, disabled.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disabled.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [LNK5] (IRQs 5 7 9 10 11 14 15) *0, disabled.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 *10 11 14 15)
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 10 *11 14 15)
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [LP2P] (IRQs 5 7 9 10 11 14 15) *0, disabled.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [LUBA] (IRQs 5 7 9 10 11 14 15) *0, disabled.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 *10 11 14 15)
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [LMC1] (IRQs 5 7 9 *10 11 14 15)
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [LAZA] (IRQs *5 7 9 10 11 14 15)
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 10 11 14 15) *0, disabled.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [LUB2] (IRQs 5 7 9 10 11 14 15) *0, disabled.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 *10 11 14 15)
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 10 *11 14 15)
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [LSA2] (IRQs *5 7 9 10 11 14 15)
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [APC3] (IRQs 1 *0, disabled.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0, disabled.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0, disabled.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [AMC1] (IRQs 20 21 22 23) *0, disabled.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0, disabled.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [ASA2] (IRQs 20 21 22 23) *0, disabled.
Mar 31 16:35:41 localhost Generic PHY: Registered new driver
Mar 31 16:35:41 localhost SCSI subsystem initialized
Mar 31 16:35:41 localhost libata version 2.00 loaded.
Mar 31 16:35:41 localhost usbcore: registered new interface driver usbfs
Mar 31 16:35:41 localhost usbcore: registered new interface driver hub
Mar 31 16:35:41 localhost usbcore: registered new device driver usb
Mar 31 16:35:41 localhost PCI: Using ACPI for IRQ routing
Mar 31 16:35:41 localhost PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
Mar 31 16:35:41 localhost hpet0: at MMIO 0xfefff000, IRQs 2, 8, 31
Mar 31 16:35:41 localhost hpet0: 3 32-bit timers, 25000000 Hz
Mar 31 16:35:41 localhost PCI-DMA: Disabling IOMMU.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
Mar 31 16:35:41 localhost ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 19
Mar 31 16:35:41 localhost ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[fdeff000-fdeff7ff] Max Packet=[2048] IR/IT contexts=[4/8]
Mar 31 16:35:41 localhost PCI: Bridge: 0000:00:06.0
Mar 31 16:35:41 localhost IO window: disabled.
Mar 31 16:35:41 localhost MEM window: fde00000-fdefffff
Mar 31 16:35:41 localhost PREFETCH window: disabled.
Mar 31 16:35:41 localhost PCI: Bridge: 0000:00:0a.0
Mar 31 16:35:41 localhost IO window: disabled.
Mar 31 16:35:41 localhost MEM window: disabled.
Mar 31 16:35:41 localhost PREFETCH window: disabled.
Mar 31 16:35:41 localhost PCI: Bridge: 0000:00:0b.0
Mar 31 16:35:41 localhost IO window: disabled.
Mar 31 16:35:41 localhost MEM window: disabled.
Mar 31 16:35:41 localhost PREFETCH window: disabled.
Mar 31 16:35:41 localhost PCI: Bridge: 0000:00:0c.0
Mar 31 16:35:41 localhost IO window: disabled.
Mar 31 16:35:41 localhost MEM window: disabled.
Mar 31 16:35:41 localhost PREFETCH window: disabled.
Mar 31 16:35:41 localhost PCI: Bridge: 0000:00:0d.0
Mar 31 16:35:41 localhost IO window: disabled.
Mar 31 16:35:41 localhost MEM window: disabled.
Mar 31 16:35:41 localhost PREFETCH window: disabled.
Mar 31 16:35:41 localhost PCI: Bridge: 0000:00:0e.0
Mar 31 16:35:41 localhost IO window: 8000-9fff
Mar 31 16:35:41 localhost MEM window: fdd00000-fddfffff
Mar 31 16:35:41 localhost PREFETCH window: disabled.
Mar 31 16:35:41 localhost PCI: Bridge: 0000:00:0f.0
Mar 31 16:35:41 localhost IO window: 7000-7fff
Mar 31 16:35:41 localhost MEM window: f8000000-fbffffff
Mar 31 16:35:41 localhost PREFETCH window: e0000000-efffffff
Mar 31 16:35:41 localhost PCI: Setting latency timer of device 0000:00:06.0 to 64
Mar 31 16:35:41 localhost PCI: Setting latency timer of device 0000:00:0a.0 to 64
Mar 31 16:35:41 localhost PCI: Setting latency timer of device 0000:00:0b.0 to 64
Mar 31 16:35:41 localhost PCI: Setting latency timer of device 0000:00:0c.0 to 64
Mar 31 16:35:41 localhost PCI: Setting latency timer of device 0000:00:0d.0 to 64
Mar 31 16:35:41 localhost PCI: Setting latency timer of device 0000:00:0e.0 to 64
Mar 31 16:35:41 localhost PCI: Setting latency timer of device 0000:00:0f.0 to 64
Mar 31 16:35:41 localhost NET: Registered protocol family 2
Mar 31 16:35:41 localhost IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
Mar 31 16:35:41 localhost TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
Mar 31 16:35:41 localhost TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
Mar 31 16:35:41 localhost TCP: Hash tables configured (established 262144 bind 65536)
Mar 31 16:35:41 localhost TCP reno registered
Mar 31 16:35:41 localhost Total HugeTLB memory allocated, 0
Mar 31 16:35:41 localhost Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Mar 31 16:35:41 localhost NTFS driver 2.1.27 [Flags: R/W].
Mar 31 16:35:41 localhost io scheduler noop registered
Mar 31 16:35:41 localhost io scheduler deadline registered
Mar 31 16:35:41 localhost io scheduler cfq registered (default)
Mar 31 16:35:41 localhost PCI: Setting latency timer of device 0000:00:0a.0 to 64
Mar 31 16:35:41 localhost pcie_portdrv_probe->Dev[0376:10de] has invalid IRQ. Check vendor BIOS
Mar 31 16:35:41 localhost assign_interrupt_mode Found MSI capability
Mar 31 16:35:41 localhost Allocate Port Service[0000:00:0a.0:pcie00]
Mar 31 16:35:41 localhost Allocate Port Service[0000:00:0a.0:pcie03]
Mar 31 16:35:41 localhost PCI: Setting latency timer of device 0000:00:0b.0 to 64
Mar 31 16:35:41 localhost pcie_portdrv_probe->Dev[0374:10de] has invalid IRQ. Check vendor BIOS
Mar 31 16:35:41 localhost assign_interrupt_mode Found MSI capability
Mar 31 16:35:41 localhost Allocate Port Service[0000:00:0b.0:pcie00]
Mar 31 16:35:41 localhost Allocate Port Service[0000:00:0b.0:pcie03]
Mar 31 16:35:41 localhost PCI: Setting latency timer of device 0000:00:0c.0 to 64
Mar 31 16:35:41 localhost pcie_portdrv_probe->Dev[0374:10de] has invalid IRQ. Check vendor BIOS
Mar 31 16:35:41 localhost assign_interrupt_mode Found MSI capability
Mar 31 16:35:41 localhost Allocate Port Service[0000:00:0c.0:pcie00]
Mar 31 16:35:41 localhost Allocate Port Service[0000:00:0c.0:pcie03]
Mar 31 16:35:41 localhost PCI: Setting latency timer of device 0000:00:0d.0 to 64
Mar 31 16:35:41 localhost pcie_portdrv_probe->Dev[0378:10de] has invalid IRQ. Check vendor BIOS
Mar 31 16:35:41 localhost assign_interrupt_mode Found MSI capability
Mar 31 16:35:41 localhost Allocate Port Service[0000:00:0d.0:pcie00]
Mar 31 16:35:41 localhost Allocate Port Service[0000:00:0d.0:pcie03]
Mar 31 16:35:41 localhost PCI: Setting latency timer of device 0000:00:0e.0 to 64
Mar 31 16:35:41 localhost pcie_portdrv_probe->Dev[0375:10de] has invalid IRQ. Check vendor BIOS
Mar 31 16:35:41 localhost assign_interrupt_mode Found MSI capability
Mar 31 16:35:41 localhost Allocate Port Service[0000:00:0e.0:pcie00]
Mar 31 16:35:41 localhost Allocate Port Service[0000:00:0e.0:pcie03]
Mar 31 16:35:41 localhost PCI: Setting latency timer of device 0000:00:0f.0 to 64
Mar 31 16:35:41 localhost pcie_portdrv_probe->Dev[0377:10de] has invalid IRQ. Check vendor BIOS
Mar 31 16:35:41 localhost assign_interrupt_mode Found MSI capability
Mar 31 16:35:41 localhost Allocate Port Service[0000:00:0f.0:pcie00]
Mar 31 16:35:41 localhost Allocate Port Service[0000:00:0f.0:pcie03]
Mar 31 16:35:41 localhost Real Time Clock Driver v1.12ac
Mar 31 16:35:41 localhost hpet_resources: 0xfefff000 is busy
Mar 31 16:35:41 localhost Linux agpgart interface v0.101 (c) Dave Jones
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [APC6] enabled at IRQ 16
Mar 31 16:35:41 localhost ACPI: PCI Interrupt 0000:07:00.0[A] -> Link [APC6] -> GSI 16 (level, low) -> IRQ 16
Mar 31 16:35:41 localhost nvidiafb: Device ID: 10de0402
Mar 31 16:35:41 localhost nvidiafb: unknown NV_ARCH
Mar 31 16:35:41 localhost ACPI: Power Button (FF) [PWRF]
Mar 31 16:35:41 localhost ACPI: Power Button (CM) [PWRB]
Mar 31 16:35:41 localhost ACPI: Fan [FAN] (on)
Mar 31 16:35:41 localhost ACPI: Thermal Zone [THRM] (40 C)
Mar 31 16:35:41 localhost Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
Mar 31 16:35:41 localhost serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Mar 31 16:35:41 localhost RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Mar 31 16:35:41 localhost loop: loaded (max 8 devices)
Mar 31 16:35:41 localhost Marvell 88E1101: Registered new driver
Mar 31 16:35:41 localhost forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.57.
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23
Mar 31 16:35:41 localhost ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APCH] -> GSI 23 (level, low) -> IRQ 23
Mar 31 16:35:41 localhost PCI: Setting latency timer of device 0000:00:08.0 to 64
Mar 31 16:35:41 localhost forcedeth: using HIGHDMA
Mar 31 16:35:41 localhost eth0: forcedeth.c: subsystem: 01043:8239 bound to 0000:00:08.0
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [AMC1] enabled at IRQ 22
Mar 31 16:35:41 localhost ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [AMC1] -> GSI 22 (level, low) -> IRQ 22
Mar 31 16:35:41 localhost PCI: Setting latency timer of device 0000:00:09.0 to 64
Mar 31 16:35:41 localhost forcedeth: using HIGHDMA
Mar 31 16:35:41 localhost eth1: forcedeth.c: subsystem: 01043:8239 bound to 0000:00:09.0
Mar 31 16:35:41 localhost tun: Universal TUN/TAP device driver, 1.6
Mar 31 16:35:41 localhost tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
Mar 31 16:35:41 localhost netconsole: not configured, aborting
Mar 31 16:35:41 localhost Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
Mar 31 16:35:41 localhost ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Mar 31 16:35:41 localhost NFORCE-MCP55: IDE controller at PCI slot 0000:00:04.0
Mar 31 16:35:41 localhost NFORCE-MCP55: chipset revision 161
Mar 31 16:35:41 localhost NFORCE-MCP55: not 100% native mode: will probe irqs later
Mar 31 16:35:41 localhost NFORCE-MCP55: 0000:00:04.0 (rev a1) UDMA133 controller
Mar 31 16:35:41 localhost ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
Mar 31 16:35:41 localhost Probing IDE interface ide0...
Mar 31 16:35:41 localhost ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011d800012bd968]
Mar 31 16:35:41 localhost Probing IDE interface ide0...
Mar 31 16:35:41 localhost Probing IDE interface ide1...
Mar 31 16:35:41 localhost megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
Mar 31 16:35:41 localhost megaraid: 2.20.4.9 (Release Date: Sun Jul 16 12:27:22 EST 2006)
Mar 31 16:35:41 localhost megasas: 00.00.03.05 Mon Oct 02 11:21:32 PDT 2006
Mar 31 16:35:41 localhost ahci 0000:06:00.0: version 2.0
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [APC7] enabled at IRQ 16
Mar 31 16:35:41 localhost ACPI: PCI Interrupt 0000:06:00.0[A] -> Link [APC7] -> GSI 16 (level, low) -> IRQ 16
Mar 31 16:35:41 localhost PCI: Setting latency timer of device 0000:06:00.0 to 64
Mar 31 16:35:41 localhost ahci 0000:06:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
Mar 31 16:35:41 localhost ahci 0000:06:00.0: flags: 64bit ncq pm led clo pmp pio slum part
Mar 31 16:35:41 localhost ata1: SATA max UDMA/133 cmd 0xFFFFC20000040100 ctl 0x0 bmdma 0x0 irq 16
Mar 31 16:35:41 localhost ata2: SATA max UDMA/133 cmd 0xFFFFC20000040180 ctl 0x0 bmdma 0x0 irq 16
Mar 31 16:35:41 localhost scsi0 : ahci
Mar 31 16:35:41 localhost ata1: SATA link down (SStatus 0 SControl 300)
Mar 31 16:35:41 localhost scsi1 : ahci
Mar 31 16:35:41 localhost ata2: SATA link down (SStatus 0 SControl 300)
Mar 31 16:35:41 localhost sata_nv 0000:00:05.0: version 2.0
Mar 31 16:35:41 localhost ACPI: PCI Interrupt Link [APSI] enabled at IRQ 21
Mar 31 16:35:41 localhost ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [APSI] -> GSI 21 (level, low) -> IRQ 21
Mar 31 16:35:41 localhost PCI: Setting latency timer of device 0000:00:05.0 to 64
Mar 31 16:35:41 localhost ata3: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xDC00 irq 21
Mar 31 16:35:41 localhost ata4: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xDC08 irq 21
Mar 31 16:35:41 localhost scsi2 : sata_nv
Mar 31 16:35:41 localhost ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Mar 31 16:35:41 localhost ata3.00: ATA-7, max UDMA/133, 156301488 sectors: LBA
Mar 31 16:35:41 localhost ata3.00: ata3: dev 0 multi count 1
Mar 31 16:35:41 localhost ata3.00: configured for UDMA/133
Mar 31 16:35:41 localhost scsi3 : sata_nv
Mar 31 16:35:41 localhost ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Mar 31 16:35:41 localhost ata4.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/1)
Mar 31 16:35:41 localhost ata4.00: ata4: dev 0 multi count 1
Mar 31 16:35:41 localhost ata4.00: configured for UDMA/133
Mar 31 16:35:41 localhost scsi 2:0:0:0: Direct-Access ATA Maxtor 6Y080M0 YAR5 PQ: 0 ANSI: 5
Mar 31 16:35:41 localhost SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
Mar 31 16:35:41 localhost sda: Write Protect is off
Mar 31 16:35:41 localhost sda: Mode Sense: 00 3a 00 00
Mar 31 16:35:41 localhost SCSI device sda: drive cache: write back
Mar 31 16:35:41 localhost SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
Mar 31 16:35:41 localhost sda: Write Protect is off
Mar 31 16:35:41 localhost sda: Mode Sense: 00 3a 00 00
Mar 31 16:35:41 localhost SCSI device sda: drive cache: write back
Mar 31 16:35:41 localhost sda: sda1 sda2 sda3
Mar 31 16:35:41 localhost sd 2:0:0:0: Attached scsi disk sda
Mar 31 16:35:41 localhost sd 2:0:0:0: Attached scsi generic sg0 type 0
Mar 31 16:35:41 localhost scsi 3:0:0:0: Direct-Access ATA WDC WD3200KS-00P 21.0 PQ: 0 ANSI: 5
Mar 31 16:35:41 localhost SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
Mar 31 16:35:41 localhost sdb: Write Protect is off
Mar 31 16:35:41 localhost sdb: Mode Sense: 00 3a 00 00
Mar 31 16:35:41 localhost SCSI device sdb: drive cache: write back
Mar 31 16:35:41 localhost SCSI device sdb: 6
_________________
Gankfest™ (>")> ~*

Everyone has to start somewhere, it depends on where you end up that counts! (>")>

[Erulabs]

You're getting a 169 address. This means no DHCP server is available.

None of your posted info helps in the least.
_________________
No more things should be presumed to exist than are absolutely necessary. Or really cool.

[Gankfest]

ok, so how can i fix it so it gets a dhcp address.
_________________
Gankfest™ (>")> ~*

Everyone has to start somewhere, it depends on where you end up that counts! (>")>

[Erulabs]

Make sure you have a DHCP server, or assign a static address.

In this case, as you've stated you only have a smoothwall and a modem, I would assign yourself an appropriate IP address.
_________________
No more things should be presumed to exist than are absolutely necessary. Or really cool.

[Gankfest]

Tried a static address:

config_eth0=( "192.168.0.201 netmask 255.255.255.0 brd 192.168.0.255" )
routes_eth0=( "default via 192.168.0.1" )

config_eth0=( "dhcp" )
dhcp_eth0="nodns nontp nonis"

I set it up in the smoothwall as localhost, phy. address, ip address, and still same error. When I was doing the livecd install it found a dhcp address so idk why it's not working now.
_________________
Gankfest™ (>")> ~*

Everyone has to start somewhere, it depends on where you end up that counts! (>")>

[Erulabs]

You can't have a static and DHCP at the same time... Try either

[Gankfest]

lol, if you read above you would notice I tried connecting to the modem already GG. My ISP is fine.
_________________
Gankfest™ (>")> ~*

Everyone has to start somewhere, it depends on where you end up that counts! (>")>

[Gankfest]

fixed it: https://forums.gentoo.org/viewtopic-t-681368-highlight-dhcpcd.html
_________________
Gankfest™ (>")> ~*

Everyone has to start somewhere, it depends on where you end up that counts! (>")>