cord
Guru
Joined: 28 Apr 2007
Posts: 344
|
 Posted: Sat Nov 03, 2007 12:36 pm Post subject: Настройка энергосбережения на ноуте |
 |
|
Делал все по этому гиду:
http://www.gentoo.org/doc/en/power-management-guide.xml
Как указано в нем, - при вставлении/вытаскивании провода питания должны быть события "Switching to AC mode" и "Switching to battery mode", но в логе их не видно...
| Code: |
[Sat Nov 3 13:51:51 2007] starting up
[Sat Nov 3 13:51:51 2007] 2 rules loaded
[Sat Nov 3 13:51:59 2007] received event "ac_adapter ACAD 00000080 00000000"
[Sat Nov 3 13:51:59 2007] executing action "/etc/acpi/actions/pmg_switch_runlevel.sh ac_adapter ACAD 00000080 00000000"
[Sat Nov 3 13:51:59 2007] BEGIN HANDLER MESSAGES
[Sat Nov 3 13:51:59 2007] END HANDLER MESSAGES
[Sat Nov 3 13:51:59 2007] action exited with status 0
[Sat Nov 3 13:51:59 2007] completed event "ac_adapter ACAD 00000080 00000000"
[Sat Nov 3 13:52:00 2007] received event "battery BAT1 00000080 00000001"
[Sat Nov 3 13:52:00 2007] executing action "/etc/acpi/actions/pmg_switch_runlevel.sh battery BAT1 00000080 00000001"
[Sat Nov 3 13:52:00 2007] BEGIN HANDLER MESSAGES
[Sat Nov 3 13:52:00 2007] END HANDLER MESSAGES
[Sat Nov 3 13:52:00 2007] action exited with status 0
[Sat Nov 3 13:52:00 2007] completed event "battery BAT1 00000080 00000001"
[Sat Nov 3 13:52:00 2007] received event "processor CPU0 00000080 00000000"
[Sat Nov 3 13:52:00 2007] completed event "processor CPU0 00000080 00000000"
[Sat Nov 3 13:56:21 2007] received event "ac_adapter ACAD 00000080 00000001"
[Sat Nov 3 13:56:21 2007] executing action "/etc/acpi/actions/pmg_switch_runlevel.sh ac_adapter ACAD 00000080 00000001"
[Sat Nov 3 13:56:21 2007] BEGIN HANDLER MESSAGES
[Sat Nov 3 13:56:22 2007] END HANDLER MESSAGES
[Sat Nov 3 13:56:22 2007] action exited with status 0
[Sat Nov 3 13:56:22 2007] completed event "ac_adapter ACAD 00000080 00000001"
[Sat Nov 3 13:56:22 2007] received event "battery BAT1 00000080 00000001"
[Sat Nov 3 13:56:22 2007] executing action "/etc/acpi/actions/pmg_switch_runlevel.sh battery BAT1 00000080 00000001"
[Sat Nov 3 13:56:22 2007] BEGIN HANDLER MESSAGES
[Sat Nov 3 13:56:22 2007] END HANDLER MESSAGES
[Sat Nov 3 13:56:22 2007] action exited with status 0
[Sat Nov 3 13:56:22 2007] completed event "battery BAT1 00000080 00000001"
[Sat Nov 3 13:56:22 2007] received event "processor CPU0 00000080 00000000"
[Sat Nov 3 13:56:22 2007] completed event "processor CPU0 00000080 00000000"
[Sat Nov 3 13:57:51 2007] exiting
[Sat Nov 3 13:57:51 2007] starting up
[Sat Nov 3 13:57:51 2007] 2 rules loaded
[Sat Nov 3 13:57:55 2007] received event "ac_adapter ACAD 00000080 00000000"
[Sat Nov 3 13:57:55 2007] executing action "/etc/acpi/actions/pmg_switch_runlevel.sh ac_adapter ACAD 00000080 00000000"
[Sat Nov 3 13:57:55 2007] BEGIN HANDLER MESSAGES
[Sat Nov 3 13:57:56 2007] END HANDLER MESSAGES
[Sat Nov 3 13:57:56 2007] action exited with status 0
[Sat Nov 3 13:57:56 2007] completed event "ac_adapter ACAD 00000080 00000000"
[Sat Nov 3 13:57:56 2007] received event "battery BAT1 00000080 00000001"
[Sat Nov 3 13:57:56 2007] executing action "/etc/acpi/actions/pmg_switch_runlevel.sh battery BAT1 00000080 00000001"
[Sat Nov 3 13:57:56 2007] BEGIN HANDLER MESSAGES
[Sat Nov 3 13:57:56 2007] END HANDLER MESSAGES
[Sat Nov 3 13:57:56 2007] action exited with status 0
[Sat Nov 3 13:57:56 2007] completed event "battery BAT1 00000080 00000001"
[Sat Nov 3 13:57:56 2007] received event "processor CPU0 00000080 00000000"
[Sat Nov 3 13:57:56 2007] completed event "processor CPU0 00000080 00000000"
[Sat Nov 3 14:08:56 2007] exiting
[Sat Nov 3 14:11:14 2007] starting up
[Sat Nov 3 14:11:14 2007] 2 rules loaded
|
до этого не выполнялся скрипт /etc/acpi/actions/pmg_switch_runlevel.sh
после того как закомментировал /etc/acpi/default.sh скрипт переключения начал выполняться, но записей в логах "Switching to AC mode" и "Switching to battery mode" все равно нет 
кто настраивал, подскажите в чем может быть проблема? |
|
Russian
