Gentoo Forums
Gentoo Forums
Gentoo Forums
Quick Search: in
Toshiba L100 + Realtek eth0 + ACPI +IRQ = sado mazo
View unanswered posts
View posts from last 24 hours

 
Reply to topic    Gentoo Forums Forum Index Russian
View previous topic :: View next topic  
Author Message
zeroQ
n00b
n00b


Joined: 03 Jul 2007
Posts: 11

PostPosted: Wed Jul 04, 2007 7:59 am    Post subject: Toshiba L100 + Realtek eth0 + ACPI +IRQ = sado mazo Reply with quote

значит есть бук Тошиба.... на нем

Code:
notik zeroq # lspci
00:00.0 Host bridge: ATI Technologies Inc Unknown device 5a31 (rev 01)
00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge
00:12.0 IDE interface: ATI Technologies Inc 4379 Serial ATA Controller (rev 80)
00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (rev 80)
00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (rev 80)
00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host Controller (rev 80)
00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 81)
00:14.1 IDE interface: ATI Technologies Inc Standard Dual Channel PCI IDE Controller (rev 80)
00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge (rev 80)
00:14.4 PCI bridge: ATI Technologies Inc IXP SB400 PCI-PCI Bridge (rev 80)
00:14.5 Multimedia audio controller: ATI Technologies Inc IXP SB400 AC'97 Audio Controller (rev 80)
00:14.6 Modem: ATI Technologies Inc SB400 AC'97 Modem Controller (rev 80)
01:05.0 VGA compatible controller: ATI Technologies Inc RC410 [Radeon Xpress 200M]
09:01.0 CardBus bridge: Texas Instruments PCI1510 PC card Cardbus Controller
09:02.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
09:04.0 Ethernet controller: Atheros Communications, Inc. AR5005G 802.11abg NIC (rev 01)


ядро

Code:
Linux notik 2.6.20-x #1 SMP Tue Jul 3 23:58:55 MSD 2007 i686 Intel(R) Celeron(R) M processor 1.70GHz GenuineIntel GNU/Linux
из портажа собрано через genkernel.....

Проблема в том что вырубаеться сетевуха через некоторое время... причем намертво... ifconfig down/up не помогает.. unplug кабеля не помогает... тока ребут машины.... dmesg выдает такую тему...

Code:
 notik zeroq # dmesg
Linux version 2.6.20-x (root@notik) (gcc версия 4.1.2 (Gentoo 4.1.2)) #1 SMP Tue
 Jul 3 23:58:55 MSD 2007
BIOS-provided physical RAM map:
sanitize start
sanitize end
copy_e820_map() start: 0000000000000000 size: 000000000009f800 end: 000000000009
f800 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000000009f800 size: 0000000000000800 end: 00000000000a
0000 type: 2
copy_e820_map() start: 00000000000dc000 size: 0000000000024000 end: 000000000010
0000 type: 2
copy_e820_map() start: 0000000000100000 size: 000000002ddb0000 end: 000000002deb
0000 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000002deb0000 size: 0000000000006000 end: 000000002deb
6000 type: 3
copy_e820_map() start: 000000002deb6000 size: 000000000004a000 end: 000000002df0
0000 type: 4
copy_e820_map() start: 000000002df00000 size: 0000000000100000 end: 000000002e00
0000 type: 2
copy_e820_map() start: 00000000e0000000 size: 0000000010000000 end: 00000000f000
0000 type: 2
copy_e820_map() start: 00000000fec00000 size: 0000000000010000 end: 00000000fec1
0000 type: 2
copy_e820_map() start: 00000000fee00000 size: 0000000000001000 end: 00000000fee0
1000 type: 2
copy_e820_map() start: 00000000fff80000 size: 0000000000080000 end: 000000010000
0000 type: 2
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000002deb0000 (usable)
 BIOS-e820: 000000002deb0000 - 000000002deb6000 (ACPI data)
 BIOS-e820: 000000002deb6000 - 000000002df00000 (ACPI NVS)
 BIOS-e820: 000000002df00000 - 000000002e000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
734MB LOWMEM available.
found SMP MP-table at 000f70b0
Entering add_active_range(0, 0, 188080) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   188080
  HighMem    188080 ->   188080
early_node_map[1] active PFN ranges
    0:        0 ->   188080
On node 0 totalpages: 188080
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 1437 pages used for memmap
  Normal zone: 182547 pages, LIFO batch:31
  HighMem zone: 0 pages used for memmap
DMI present.
ACPI: RSDP (v000 TOSQCI                                ) @ 0x000f7080
ACPI: RSDT (v001 TOSQCI L10      0x06040000  LTP 0x00000000) @ 0x2deb15c5
ACPI: FADT (v001 ATI    Goldfish 0x06040000 ATI  0x000f4240) @ 0x2deb5f00
ACPI: MADT (v001 PTLTD           APIC   0x06040000  LTP 0x00000000) @ 0x2deb5f74
ACPI: MCFG (v001 PTLTD    MCFG   0x06040000  LTP 0x00000000) @ 0x2deb5fc4
ACPI: SSDT (v001  PmRef  Cpu0Cst 0x00003001 INTL 0x20030224) @ 0x2deb17ff
ACPI: SSDT (v001  PmRef    CpuPm 0x00003000 INTL 0x20030224) @ 0x2deb15fd
ACPI: DSDT (v001 TOSQCI L10      0x06040000 MSFT 0x0100000c) @ 0x00000000
ATI board detected. Disabling timer routing over 8254.
ACPI: PM-Timer IO Port: 0x8008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:13 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 33, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 2e000000:b2000000)
Detected 1695.843 MHz processor.
Built 1 zonelists.  Total pages: 186611
Kernel command line: BOOT_IMAGE=Gentoo ro root=804 init=/linuxrc ramdisk=8192 re
al_root=/dev/sda4 udev
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 739616k/752320k available (2680k kernel code, 12200k reserved, 1191k dat
a, 244k init, 0k highmem)
virtual kernel memory layout:
    fixmap  : 0xfff9d000 - 0xfffff000   ( 392 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xee800000 - 0xff7fe000   ( 271 MB)
    lowmem  : 0xc0000000 - 0xedeb0000   ( 734 MB)
      .init : 0xc04cf000 - 0xc050c000   ( 244 kB)
      .data : 0xc039e13c - 0xc04c7fb0   (1191 kB)
      .text : 0xc0100000 - 0xc039e13c   (2680 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3395.32 BogoMIPS (lpj=6790649)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afe9fbff 00100000 00000000 00000000 00000000
00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: After all inits, caps: afe9fbff 00100000 00000000 00002040 00000000 0000000
0 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 16k freed
ACPI: Core revision 20060707
CPU0: Intel(R) Celeron(R) M processor         1.70GHz stepping 08
Total of 1 processors activated (3395.32 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ...  failed.
...trying to set up timer as Virtual Wire IRQ... works.
Brought up 1 CPUs
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Scanning bus 0000:00
PCI: Found 0000:00:00.0 [1002/5a31] 000600 00
PCI: Calling quirk c0316bf0 for 0000:00:00.0
PCI: Found 0000:00:01.0 [1002/5a3f] 000604 01
PCI: Calling quirk c0316bf0 for 0000:00:01.0
PCI: Found 0000:00:12.0 [1002/4379] 000101 00
PCI: Calling quirk c0316bf0 for 0000:00:12.0
PCI: Found 0000:00:13.0 [1002/4374] 000c03 00
PCI: Calling quirk c0316bf0 for 0000:00:13.0
PCI: Found 0000:00:13.1 [1002/4375] 000c03 00
PCI: Calling quirk c0316bf0 for 0000:00:13.1
PCI: Found 0000:00:13.2 [1002/4373] 000c03 00
PCI: Calling quirk c0316bf0 for 0000:00:13.2
PCI: Found 0000:00:14.0 [1002/4372] 000c05 00
PCI: Calling quirk c0316bf0 for 0000:00:14.0
PCI: Found 0000:00:14.1 [1002/4376] 000101 00
PCI: Calling quirk c0316bf0 for 0000:00:14.1
PCI: Found 0000:00:14.3 [1002/4377] 000601 00
PCI: Calling quirk c0316bf0 for 0000:00:14.3
PCI: Found 0000:00:14.4 [1002/4371] 000604 01
PCI: Calling quirk c0316bf0 for 0000:00:14.4
PCI: Found 0000:00:14.5 [1002/4370] 000401 00
PCI: Calling quirk c0316bf0 for 0000:00:14.5
PCI: Found 0000:00:14.6 [1002/4378] 000703 00
PCI: Calling quirk c0316bf0 for 0000:00:14.6
PCI: Fixups for bus 0000:00
PCI: Scanning behind PCI bridge 0000:00:01.0, config 010100, pass 0
PCI: Scanning bus 0000:01
PCI: Found 0000:01:05.0 [1002/5a62] 000300 00
PCI: Calling quirk c0316bf0 for 0000:01:05.0
Boot video device is 0000:01:05.0
PCI: Fixups for bus 0000:01
PCI: Bus scan for 0000:01 returning with max=01
PCI: Scanning behind PCI bridge 0000:00:14.4, config 0e0900, pass 0
PCI: Scanning bus 0000:09
PCI: Found 0000:09:01.0 [104c/ac56] 000607 02
PCI: Calling quirk c0316bf0 for 0000:09:01.0
PCI: Found 0000:09:02.0 [10ec/8139] 000200 00
PCI: Calling quirk c0316bf0 for 0000:09:02.0
PCI: Found 0000:09:04.0 [168c/001a] 000200 00
PCI: Calling quirk c0316bf0 for 0000:09:04.0
PCI: Fixups for bus 0000:09
PCI: Transparent bridge - 0000:00:14.4
PCI: Scanning behind PCI bridge 0000:09:01.0, config 000000, pass 0
PCI: Scanning behind PCI bridge 0000:09:01.0, config 000000, pass 1
PCI: Bus scan for 0000:09 returning with max=0d
PCI: Scanning behind PCI bridge 0000:00:01.0, config 010100, pass 1
PCI: Scanning behind PCI bridge 0000:00:14.4, config 0e0900, pass 1
PCI: Bus scan for 0000:00 returning with max=0e
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
SCSI subsystem initialized
libata version 2.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
  got res [34000000:3407ffff] bus [34000000:3407ffff] flags 7200 for BAR 6 of 00
00:00:12.0
  got res [d0120000:d013ffff] bus [d0120000:d013ffff] flags 7202 for BAR 6 of 00
00:01:05.0
PCI: Bridge: 0000:00:01.0
  IO window: 9000-9fff
  MEM window: d0100000-d01fffff
  PREFETCH window: d4000000-d7ffffff
  got res [d0211000:d0211fff] bus [d0211000:d0211fff] flags 200 for BAR 0 of 000
0:09:01.0
PCI: moved device 0000:09:01.0 resource 0 (200) to d0211000
PCI: Bus 10, cardbus bridge: 0000:09:01.0
  IO window: 0000a400-0000a4ff
  IO window: 0000a800-0000a8ff
  PREFETCH window: 30000000-33ffffff
  MEM window: 38000000-3bffffff
PCI: Bridge: 0000:00:14.4
  IO window: a000-afff
  MEM window: d0200000-d02fffff
  PREFETCH window: 30000000-33ffffff
PCI: Enabling device 0000:09:01.0 (0000 -> 0003)
ACPI: PCI Interrupt 0000:09:01.0[A] -> GSI 20 (level, low) -> IRQ 16
PCI: Enabling bus mastering for device 0000:09:01.0
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 704k freed
Machine check exception polling timer started.
IA-32 Microcode Update Driver: v1.14a <tigran@aivazian.fsnet.co.uk>
Total HugeTLB memory allocated, 0
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
PCI: Calling quirk c021822a for 0000:00:00.0
PCI: Calling quirk c02f593a for 0000:00:00.0
PCI: Calling quirk c021822a for 0000:00:01.0
PCI: Calling quirk c02f593a for 0000:00:01.0
PCI: Calling quirk c021822a for 0000:00:12.0
PCI: Calling quirk c02f593a for 0000:00:12.0
PCI: Calling quirk c021822a for 0000:00:13.0
PCI: Calling quirk c02f593a for 0000:00:13.0
PCI: Calling quirk c021822a for 0000:00:13.1
PCI: Calling quirk c02f593a for 0000:00:13.1
PCI: Calling quirk c021822a for 0000:00:13.2
PCI: Calling quirk c02f593a for 0000:00:13.2
PCI: Calling quirk c021822a for 0000:00:14.0
PCI: Calling quirk c02f593a for 0000:00:14.0
PCI: Calling quirk c021822a for 0000:00:14.1
PCI: Calling quirk c02f593a for 0000:00:14.1
PCI: Calling quirk c021822a for 0000:00:14.3
PCI: Calling quirk c02f593a for 0000:00:14.3
PCI: Calling quirk c021822a for 0000:00:14.4
PCI: Calling quirk c02f593a for 0000:00:14.4
PCI: Calling quirk c021822a for 0000:00:14.5
PCI: Calling quirk c02f593a for 0000:00:14.5
PCI: Calling quirk c021822a for 0000:00:14.6
PCI: Calling quirk c02f593a for 0000:00:14.6
PCI: Calling quirk c021822a for 0000:01:05.0
PCI: Calling quirk c02f593a for 0000:01:05.0
PCI: Calling quirk c021822a for 0000:09:01.0
PCI: Calling quirk c02f593a for 0000:09:01.0
PCI: Calling quirk c021822a for 0000:09:02.0
PCI: Calling quirk c02f593a for 0000:09:02.0
PCI: Calling quirk c021822a for 0000:09:04.0
PCI: Calling quirk c02f593a for 0000:09:04.0
toshiba: not a supported Toshiba laptop
Linux agpgart interface v0.101 (c) Dave Jones
Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 sec
onds).
Hangcheck: Using get_cycles().
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ACPI: PCI Interrupt 0000:00:14.6[B] -> GSI 17 (level, low) -> IRQ 17
ACPI: PCI interrupt for device 0000:00:14.6 disabled
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ATIIXP: IDE controller at PCI slot 0000:00:14.1
ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 18
ATIIXP: chipset revision 128
ATIIXP: not 100% native mode: will probe irqs later
    ide1: BM-DMA at 0x8468-0x846f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide1...
hdc: HL-DT-ST DVDRAM GMA-4082N, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide0...
hdc: ATAPI 31X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
3ware Storage Controller device driver for Linux v1.26.02.002.
sata_sil 0000:00:12.0: version 2.0
PCI: Enabling device 0000:00:12.0 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 19
ata1: SATA max UDMA/100 cmd 0xEE812080 ctl 0xEE81208A bmdma 0xEE812000 irq 19
ata2: SATA max UDMA/100 cmd 0xEE8120C0 ctl 0xEE8120CA bmdma 0xEE812008 irq 19
scsi0 : sata_sil
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7, max UDMA/100, 117210240 sectors: LBA48 NCQ (depth 0/32)
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/100
scsi1 : sata_sil
ata2: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access     ATA      TOSHIBA MK6034GS AH10 PQ: 0 ANSI: 5
SCSI device sda: 117210240 512-byte hdwr sectors (60012 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
SCSI device sda: 117210240 512-byte hdwr sectors (60012 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
 sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: Attached scsi disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
usbmon: debugfs is not available
ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 20
ehci_hcd 0000:00:13.2: EHCI Host Controller
ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:13.2: irq 20, io mem 0xd0007000
ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 20
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.0: irq 20, io mem 0xd0005000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 20
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:13.1: irq 20, io mem 0xd0006000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
USB Universal Host Controller Interface driver v3.0
usb 2-1: new low speed USB device using ohci_hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
input: Logitech USB-PS/2 Optical Mouse as /class/input/input0
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:13.0
-1
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input1
oprofile: using NMI interrupt.
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
Using IPI Shortcut mode
Freeing unused kernel memory: 244k freed
Time: tsc clocksource has been installed.
Synaptics Touchpad, model: 1, fw: 6.2, id: 0x92a0b1, caps: 0xa04713/0x200000
synaptics: Toshiba Satellite L100                    detected, limiting rate to
40pps.
input: SynPS/2 Synaptics TouchPad as /class/input/input2
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
8139too Fast Ethernet driver 0.9.28
ACPI: PCI Interrupt 0000:09:02.0[A] -> GSI 21 (level, low) -> IRQ 21
eth0: RealTek RTL8139 at 0xee820000, 00:16:36:6b:c6:9e, IRQ 21
eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 17 (level, low) -> IRQ 17
EXT3 FS on sda4, internal journal
Adding 498004k swap on /dev/sda2.  Priority:-1 extents:1 across:498004k
Real Time Clock Driver v1.12ac
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
eth0: no IPv6 routers present
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0c 0005 c07f media 10.
eth0: Tx queue start entry 1648  dirty entry 1644.
eth0:  Tx descriptor 0 is 0008a04a. (queue head)
eth0:  Tx descriptor 1 is 0008a04a.
eth0:  Tx descriptor 2 is 0008a04a.
eth0:  Tx descriptor 3 is 0008a03c.
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1



видно что ругаеться ACPI мол чето с IRQ видимо.... пробовал кучу версию ядер разные настройки.. ставил сетевуху в режиме модуля в ядре... пофик.... причем отрубаеться чаще из за большого пробега инфы по каналу... тоесть если просто сидеть в аське и ирке то дольше работает.. как тока начинаешь скачивать большой файл отрубаеться намертво... кабель не битый... проверял... сама сетевуха рабочая под виндой пашет тип топ.... отключал поддержку ACPI в ядре и при загрузке (когда включено ACPI) выскакивает кернел паник.. тоесть без ACPI никуды.... перечитал много гуула проблем частая и у многих решалось переустановкой нового и другого дистра.... или установкой патчей для ACPI c sourceforge... но эти патчи для ядра 2.15.* и ниже вроде.. а у мну 2.6.20+... народ подскажите где копать в какую сторону?... как настроить IRQ... в биосе опции нету такой.. ХЕЛЛЛПП!!!! :( :( :( :( :( :(
Back to top
View user's profile Send private message
neroot
n00b
n00b


Joined: 16 Mar 2007
Posts: 33
Location: Россия, Н.Новгород

PostPosted: Wed Jul 04, 2007 9:04 am    Post subject: Reply with quote

Я бы начал стого, что:
1. Обновил ядро. echo sys-kernel/gentoo-sources ~x86 > /etc/portage/package.keywords && emerge gentoo-sources
2. Настроил бы ядро руками. Поэксперементировав и с аспи, и с драйвером 8139 (в особенности с ним).
И вопрос: демон acpid есть/работает в системе?
_________________
Делай, что должен и будь, что будет.
Back to top
View user's profile Send private message
zeroQ
n00b
n00b


Joined: 03 Jul 2007
Posts: 11

PostPosted: Wed Jul 04, 2007 9:16 am    Post subject: Reply with quote

как я написал ядро стоит из gentoo-sources... так же пробовал ядра повыше релизом... бес толку.. настривал конечно руками.... с опциями карты игрался как тока мог... и модуль и не молуль и опции и не опции.. без толку... acpid пашет.... =(
Back to top
View user's profile Send private message
neroot
n00b
n00b


Joined: 16 Mar 2007
Posts: 33
Location: Россия, Н.Новгород

PostPosted: Wed Jul 04, 2007 12:49 pm    Post subject: Reply with quote

Хм... А вариант биос обновить - отрабатывали?
_________________
Делай, что должен и будь, что будет.
Back to top
View user's profile Send private message
zeroQ
n00b
n00b


Joined: 03 Jul 2007
Posts: 11

PostPosted: Wed Jul 04, 2007 1:07 pm    Post subject: Reply with quote

хмм.. чето я про это подзабыл... пойду попробую...
Back to top
View user's profile Send private message
zeroQ
n00b
n00b


Joined: 03 Jul 2007
Posts: 11

PostPosted: Wed Jul 04, 2007 3:32 pm    Post subject: Reply with quote

биос не помог... =( есть еще какие варианты решения проблемы.....?
Back to top
View user's profile Send private message
calculator
Apprentice
Apprentice


Joined: 16 Oct 2006
Posts: 183
Location: Russia, Moscow

PostPosted: Wed Jul 04, 2007 8:10 pm    Post subject: Reply with quote

Этот dmesg после падения интерфейса?
Если проблема постоянно появляется при прокачке большой информации, попробуй прокачаться с livecd.
Back to top
View user's profile Send private message
zeroQ
n00b
n00b


Joined: 03 Jul 2007
Posts: 11

PostPosted: Wed Jul 04, 2007 8:54 pm    Post subject: Reply with quote

c livecd все оки доки пашет..... но мну то сеть нуна постоянно ))... dmesq после падения eth0 посление мессаги про него....
Back to top
View user's profile Send private message
calculator
Apprentice
Apprentice


Joined: 16 Oct 2006
Posts: 183
Location: Russia, Moscow

PostPosted: Wed Jul 04, 2007 9:30 pm    Post subject: Reply with quote

google по теме смотри
Оно?
Back to top
View user's profile Send private message
zeroQ
n00b
n00b


Joined: 03 Jul 2007
Posts: 11

PostPosted: Thu Jul 05, 2007 7:04 am    Post subject: Reply with quote

с гуглом я общался.... проблему такого рода бывали не тока на реалтек чипах... тоесть от чипа не зависит... проблемы решали или отключением acpi в ядре или функцией noapic... или утановкой старого ядра... или настройками в биосе по IRQ... если у мну отключить acpi или в ядре или в загрузчике то система вылетает с кернел паник... не может определить винт... он у мну sata через silicon дрова пашет.... и проблема эта связана с IRQ.. но как это вылечить не убивая acpi? в ноутах на сегодня acpi далек от идеала.... =(....
Back to top
View user's profile Send private message
zeroQ
n00b
n00b


Joined: 03 Jul 2007
Posts: 11

PostPosted: Thu Jul 05, 2007 8:13 am    Post subject: Reply with quote

не хочу ПСМСИА ))... нуна чинить....
Back to top
View user's profile Send private message
Laitr Keiows
Moderator
Moderator


Joined: 04 Jul 2005
Posts: 891
Location: Kobe, Japan

PostPosted: Fri Jul 06, 2007 1:24 am    Post subject: Reply with quote

А где содержимое логов сразу при появлении проблемы?
Back to top
View user's profile Send private message
Laitr Keiows
Moderator
Moderator


Joined: 04 Jul 2005
Posts: 891
Location: Kobe, Japan

PostPosted: Fri Jul 06, 2007 12:13 pm    Post subject: Reply with quote

Code:
Disabling IRQ #XX

перед этим случаем не появлялось?

Рекомендуют использовать ядерный параметр noirqdebug
http://www.mail-archive.com/netdev@vger.kernel.org/msg15993.html и далее по теме

Quote:
Without the i915 module both network and console switching work.


Я бы еще копнул в сторону DSDT, оно у тошибы и асуса престранное бывает.
И еще посмотрел бы что в /proc/interrupts
Back to top
View user's profile Send private message
zeroQ
n00b
n00b


Joined: 03 Jul 2007
Posts: 11

PostPosted: Fri Jul 06, 2007 3:50 pm    Post subject: Reply with quote

/proc/interrupts

Code:
           CPU0       
  0:    5560939  local-APIC-edge-fasteio   timer
  1:      15030   IO-APIC-edge      i8042
  8:          2   IO-APIC-edge      rtc
  9:        301   IO-APIC-fasteoi   acpi
 12:        124   IO-APIC-edge      i8042
 15:         25   IO-APIC-edge      ide1
 17:     281856   IO-APIC-fasteoi   ATI IXP, fglrx
 19:      33969   IO-APIC-fasteoi   libata
 20:     184035   IO-APIC-fasteoi   ehci_hcd:usb1, ohci_hcd:usb2, ohci_hcd:usb3
 21:      40025   IO-APIC-fasteoi   eth0
NMI:          0
LOC:    5560655
ERR:          0
MIS:          0


такой месаги не было даже..
Code:
Disabling IRQ #XX


ща попробую noirqdebug
Back to top
View user's profile Send private message
Laitr Keiows
Moderator
Moderator


Joined: 04 Jul 2005
Posts: 891
Location: Kobe, Japan

PostPosted: Fri Jul 06, 2007 11:34 pm    Post subject: Reply with quote

Рекомендую вот это еще:
http://gentoo-wiki.com/HOWTO_Fix_Common_ACPI_Problems

У меня когда-то на старом компе были престранные проблемы с USB: отваливались устройства и все тут.
Помогло исправление ошибок в DSDT.
Back to top
View user's profile Send private message
zeroQ
n00b
n00b


Joined: 03 Jul 2007
Posts: 11

PostPosted: Sun Jul 29, 2007 6:14 pm    Post subject: Reply with quote

да... тока разобрался и вник в фак.... dsdt и вправду buggy... нормального dsdt для моей машины на сайте acpi нету еще раз повторю это Toshiba L100-173.... выпали такие ошибки

Code:

Intel ACPI Component Architecture
ASL Optimizing Compiler version 20060912 [Jul 29 2007]
Copyright (C) 2000 - 2006 Intel Corporation
Supports ACPI Specification Revision 3.0a

acpi.dsl   158:     Method (_WAK, 1, NotSerialized)
Warning  1079 -                ^ Reserved method must return a value (_WAK)

acpi.dsl  1642:                 Field (SMB, WordAcc, NoLock, Preserve)
Error    4026 -                          ^ Access width is greater than region size

acpi.dsl  1644:                     SIRQ,   8
Error    4027 -                        ^ Access width of Field Unit extends beyond region limit

acpi.dsl  4048:                                 Name (_T_0, 0x00)
Error    4081 -                     Use of reserved word ^  (_T_0)

acpi.dsl  4126:                                 Name (_T_0, 0x00)
Error    4081 -                     Use of reserved word ^  (_T_0)

acpi.dsl  4602:             Method (EVNT, 1, NotSerialized)
Warning  1086 -                        ^ Not all control paths return a value (EVNT)

acpi.dsl  4929:                     Name (_T_0, 0x00)
Error    4081 -         Use of reserved word ^  (_T_0)

ASL Input:  acpi.dsl - 5275 lines, 186429 bytes, 2160 keywords
Compilation complete. 5 Errors, 2 Warnings, 0 Remarks, 917 Optimizations



поискал такие же ошибки у гугла... но так как ни там чинять (заменяют код) мну помоему не подойдет... текст исходный у людей и у мну разный... я не уровня программера, посему исправление для меня сложновато.... есть ли какая нить сслыка с подробным описанием ошибок и их исправлением... PLZZZ HELP!!! вот мой dsdt - http://paste.org.ru/?sh7sdf
Back to top
View user's profile Send private message
Kee_Keekkenen
n00b
n00b


Joined: 01 Dec 2005
Posts: 34

PostPosted: Sun Aug 05, 2007 7:23 pm    Post subject: Reply with quote

а что в .config ?
Back to top
View user's profile Send private message
akam
Tux's lil' helper
Tux's lil' helper


Joined: 04 Sep 2006
Posts: 82
Location: Nab. Chelny, Russia

PostPosted: Thu Sep 13, 2007 5:41 pm    Post subject: Reply with quote

Кто нибудь смог решить проблему?
Back to top
View user's profile Send private message
akam
Tux's lil' helper
Tux's lil' helper


Joined: 04 Sep 2006
Posts: 82
Location: Nab. Chelny, Russia

PostPosted: Fri Sep 14, 2007 8:42 am    Post subject: Reply with quote

Toshiba Satellite L30
Сетевуха работает нормально на ядре собранном БЕЗ APM/ACPI или загруженным с опцией acpi=off
Но на ноуте это не решение пробдемы :(
Back to top
View user's profile Send private message
Display posts from previous:   
Reply to topic    Gentoo Forums Forum Index Russian All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum