| View previous topic :: View next topic |
| Author |
Message |
Kernel78
Moderator
Joined: 24 Jun 2005
Posts: 3654
|
 Posted: Thu Apr 05, 2007 9:22 am Post subject: |
 |
|
Rispondi a zocram e non a me ? potrei diventare permaloso 
_________________
Le tre grandi virtù di un programmatore: pigrizia, impazienza e arroganza. (Larry Wall).
Prima di postare un file togli i commenti con | Code: | | grep -vE '(^[[:space:]]*($|(#|!|;|//)))' |
|
|
| Back to top |
|
 |
canduc17
l33t
Joined: 11 Oct 2005
Posts: 795
Location: Ferrara, Italy
|
| Posted: Thu Apr 05, 2007 9:34 am Post subject: |
|
|
Scusa Kernel78, ma il tuo post non l'avevo proprio visto...
Allora: il supporto USB nel kernel c'è, tant'è che a manoni riesco a montare la penna senza problemi.
Se inserisco un cd, la famigerata finestra si apre!
Ecco dmesg | tail prima dell'inserimento penna: | Code: | candacer canduc # dmesg | tail
sda: assuming drive cache: write through
SCSI device sda: 2013184 512-byte hdwr sectors (1031 MB)
sda: Write Protect is off
sda: Mode Sense: 23 00 00 00
sda: assuming drive cache: write through
sda: sda1
sd 1:0:0:0: Attached scsi removable disk sda
usb-storage: device scan complete
usb 1-2: USB disconnect, address 4
spurious 8259A interrupt: IRQ7.
|
e dopo | Code: | candacer canduc # dmesg | tail
sda: Write Protect is off
sda: Mode Sense: 23 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 2013184 512-byte hdwr sectors (1031 MB)
sda: Write Protect is off
sda: Mode Sense: 23 00 00 00
sda: assuming drive cache: write through
sda: sda1
sd 2:0:0:0: Attached scsi removable disk sda
usb-storage: device scan complete |
_________________
A cow enters a supermarket, does an handstand and dies. (Public toilet graffito) |
|
| Back to top |
|
|
102376
l33t
Joined: 19 Mar 2005
Posts: 608
|
| Posted: Thu Apr 05, 2007 10:44 am Post subject: |
|
|
| Quote: | | Per permettere ciò dovete aver compilato KDE con la variabile USE hal |
l'hai fatto, magari hal serve solo per le usb.
dai un |
|
| Back to top |
|
|
canduc17
l33t
Joined: 11 Oct 2005
Posts: 795
Location: Ferrara, Italy
|
| Posted: Thu Apr 05, 2007 11:38 am Post subject: |
|
|
| Code: | candacer canduc # equery uses kde
[ Searching for packages matching kde... ]
!!! No matching packages found for "kde"
candacer canduc # equery uses kdebase-startkde
[ Searching for packages matching kdebase-startkde... ]
[ Colour Code : set unset ]
[ Legend : Left column (U) - USE flags from make.conf ]
[ : Right column (I) - USE flags packages was installed with ]
[ Found these USE variables for kde-base/kdebase-startkde-3.5.5 ]
U I
- + arts : Adds support for aRts: the KDE sound daemon
- - debug : Enable extra debug codepaths, like asserts and extra output. If you want to get meaningful backtraces see http://www.gentoo.org/proj/en/qa/backtraces.xml .
- - elibc_FreeBSD : <unknown>
- - kdeenablefinal : EXPERIMENTAL: KDE ebuilds will use the enable-final flag, yielding big compilation speedups at the cost of heavy mem usage.
- - xinerama : Add support for the xinerama X11 extension, which allows you to stretch your display across multiple monitors |
Con equery uses kde non ho risultati, facendo equery uses kdebase-startkde ottengo l'output sopra, ma di hal non si parla...Io comunque credo di averso settato...
Se non l'ho fatto devo ricompilare kde?! 
_________________
A cow enters a supermarket, does an handstand and dies. (Public toilet graffito) |
|
| Back to top |
|
|
comio
Advocate
Joined: 03 Jul 2003
Posts: 2191
Location: Taranto
|
| Posted: Thu Apr 05, 2007 12:09 pm Post subject: |
|
|
sei nel gruppo plugdev? (si chiama così?)
ciao
_________________
RTFM!!!!
e
http://www.comio.it
 |
|
| Back to top |
|
|
canduc17
l33t
Joined: 11 Oct 2005
Posts: 795
Location: Ferrara, Italy
|
| Posted: Thu Apr 05, 2007 12:09 pm Post subject: |
|
|
Rettifico: se inserisco un cd, la finestra si apre, ma poi non mi fà accedere al contenuto, dandomi il messaggio:Autorizzazioni negate.
L'indirizzo dove monta il cd è system:/media/hdc, ma anche se cerco di accedervi come root, mi dà lo stesso messaggio di errore.
Non so se può essere utile, ma la configurazione del lettore cd in /etc/fstab è: | Code: | | /dev/cdrom /mnt/cdrom auto auto,user,canduc 0 0 |
@ comio: Sì che sono in plugdev...mi sono aggiunto come suggeritomi due o tre post sopra...
_________________
A cow enters a supermarket, does an handstand and dies. (Public toilet graffito) |
|
| Back to top |
|
|
Scen
Retired Dev
Joined: 29 Jul 2003
Posts: 2470
Location: Padova, Italy
|
| Posted: Thu Apr 05, 2007 12:21 pm Post subject: |
|
|
Se stai utilizzando il trio dbus-hald-kdebase-kioslaves NON devi inserire nessuna voce in /etc/fstab, altrimenti il comportamento predefinito del montaggio automatico va in crisi.
_________________
I was born in a deep forest/I wish I could live here all my life/I am made from stones and roots/My home, these woods and roads
All my life I loved this sound/Of the woods all around/Eagles flies where the winds blows free
Journey is my destiny |
|
| Back to top |
|
|
canduc17
l33t
Joined: 11 Oct 2005
Posts: 795
Location: Ferrara, Italy
|
| Posted: Thu Apr 05, 2007 12:31 pm Post subject: |
|
|
Infatti: commentando quella riga in fstab accedo al contenuto del cd senza problemi.
Per le penne USB, invece, continua a non aprirsi nessun popup...
_________________
A cow enters a supermarket, does an handstand and dies. (Public toilet graffito) |
|
| Back to top |
|
|
Scen
Retired Dev
Joined: 29 Jul 2003
Posts: 2470
Location: Padova, Italy
|
| Posted: Thu Apr 05, 2007 12:49 pm Post subject: |
|
|
Per me ti manca qualche supporto nel kernel. Hai attivato il supporto SCSI ai dischi? (CONFIG_BLK_DEV_SD)
| Code: |
Device Drivers --->
SCSI device support --->
<*> SCSI disk support
|
_________________
I was born in a deep forest/I wish I could live here all my life/I am made from stones and roots/My home, these woods and roads
All my life I loved this sound/Of the woods all around/Eagles flies where the winds blows free
Journey is my destiny |
|
| Back to top |
|
|
canduc17
l33t
Joined: 11 Oct 2005
Posts: 795
Location: Ferrara, Italy
|
| Posted: Thu Apr 05, 2007 12:59 pm Post subject: |
|
|
La mia condizione attuale è questa: | Code: | < > RAID Transport Class
<*> SCSI device support
< > SCSI target support
[*] legacy /proc/scsi/ support
--- SCSI support type (disk, tape, CD-ROM)
<*> SCSI disk support
< > SCSI tape support
< > SCSI OnStream SC-x0 tape support
< > SCSI CDROM support
< > SCSI generic support
< > SCSI media changer support
--- Some SCSI devices (e.g. CD jukebox) support multiple LUNs
[ ] Probe all LUNs on each SCSI device
[ ] Verbose SCSI error reporting (kernel size +=12K)
[ ] SCSI logging facility
[ ] Asynchronous SCSI scanning
SCSI Transports --->
SCSI low-level drivers --->
PCMCIA SCSI adapter support ---> |
Che io debba forse abilitare SCSI generic support?
_________________
A cow enters a supermarket, does an handstand and dies. (Public toilet graffito) |
|
| Back to top |
|
|
Scen
Retired Dev
Joined: 29 Jul 2003
Posts: 2470
Location: Padova, Italy
|
| Posted: Thu Apr 05, 2007 1:11 pm Post subject: |
|
|
No, qui pare tutto apposto.
Meglio se posti un
| Code: |
zgrep -i usb /proc/config.gz
|
magari ti sei dimenticato di specificare qualche opzione.
_________________
I was born in a deep forest/I wish I could live here all my life/I am made from stones and roots/My home, these woods and roads
All my life I loved this sound/Of the woods all around/Eagles flies where the winds blows free
Journey is my destiny |
|
| Back to top |
|
|
simone-27
Tux's lil' helper
Joined: 19 Feb 2007
Posts: 118
|
| Posted: Thu Apr 05, 2007 1:45 pm Post subject: |
|
|
| Scen wrote: | | Se stai utilizzando il trio dbus-hald-kdebase-kioslaves NON devi inserire nessuna voce in /etc/fstab, altrimenti il comportamento predefinito del montaggio automatico va in crisi. |
non bisogna inserire neanche queste voci?
| Code: |
/dev/sda1 /boot ext2 defaults,noatime 1 2
/dev/sda3 none swap sw 0 0
/dev/sda4 / ext3 noatime 0 1
proc /proc proc defaults 0 0
shm /dev/shm tmpfs nodev,nosuid,noexec 0 0
|
o bisogna non inserire solo quelle riguardanti i cd? |
|
| Back to top |
|
|
Kernel78
Moderator
Joined: 24 Jun 2005
Posts: 3654
|
| Posted: Thu Apr 05, 2007 1:49 pm Post subject: |
|
|
| simone-27 wrote: | | Scen wrote: | | Se stai utilizzando il trio dbus-hald-kdebase-kioslaves NON devi inserire nessuna voce in /etc/fstab, altrimenti il comportamento predefinito del montaggio automatico va in crisi. |
non bisogna inserire neanche queste voci?
| Code: |
/dev/sda1 /boot ext2 defaults,noatime 1 2
/dev/sda3 none swap sw 0 0
/dev/sda4 / ext3 noatime 0 1
proc /proc proc defaults 0 0
shm /dev/shm tmpfs nodev,nosuid,noexec 0 0
|
o bisogna non inserire solo quelle riguardanti i cd? |
Le voci che non si devono inserire sono quelle riguardanti i supporti removibili.
_________________
Le tre grandi virtù di un programmatore: pigrizia, impazienza e arroganza. (Larry Wall).
Prima di postare un file togli i commenti con | Code: | | grep -vE '(^[[:space:]]*($|(#|!|;|//)))' |
|
|
| Back to top |
|
|
simone-27
Tux's lil' helper
Joined: 19 Feb 2007
Posts: 118
|
| Posted: Thu Apr 05, 2007 1:58 pm Post subject: |
|
|
gia che siamo in argomento vi pongo anche il mio problema, prima di rimuovere la riga
| Code: | | /dev/cdrom /mnt/cdrom auto noauto,user 0 0 |
dal /etc/fstab
mi dava permesso negato, ora, dopo averla rimossa d | Code: | | Tipo di file system non valido |
Idee?? |
|
| Back to top |
|
|
canduc17
l33t
Joined: 11 Oct 2005
Posts: 795
Location: Ferrara, Italy
|
| Posted: Thu Apr 05, 2007 1:59 pm Post subject: |
|
|
| Code: | candacer canduc # zgrep -i usb /proc/config.gz
# CONFIG_USB_ZD1201 is not set
# CONFIG_USB_DABUSB is not set
# USB devices
# CONFIG_SND_USB_AUDIO is not set
# CONFIG_SND_USB_USX2Y is not set
# USB support
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set
# Miscellaneous USB options
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_BANDWIDTH is not set
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_SUSPEND is not set
# CONFIG_USB_OTG is not set
# USB Host Controller Drivers
CONFIG_USB_EHCI_HCD=y
# CONFIG_USB_EHCI_SPLIT_ISO is not set
# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
# CONFIG_USB_EHCI_TT_NEWSCHED is not set
# CONFIG_USB_ISP116X_HCD is not set
CONFIG_USB_OHCI_HCD=y
# CONFIG_USB_OHCI_BIG_ENDIAN is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
CONFIG_USB_UHCI_HCD=y
# CONFIG_USB_SL811_HCD is not set
# USB Device Class drivers
# CONFIG_USB_ACM is not set
# CONFIG_USB_PRINTER is not set
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
# may also be needed; see USB_STORAGE Help for more information
CONFIG_USB_STORAGE=y
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_DATAFAB is not set
# CONFIG_USB_STORAGE_FREECOM is not set
# CONFIG_USB_STORAGE_ISD200 is not set
# CONFIG_USB_STORAGE_DPCM is not set
# CONFIG_USB_STORAGE_USBAT is not set
# CONFIG_USB_STORAGE_SDDR09 is not set
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
# CONFIG_USB_STORAGE_ALAUDA is not set
# CONFIG_USB_STORAGE_KARMA is not set
# CONFIG_USB_LIBUSUAL is not set
# USB Input Devices
CONFIG_USB_HID=y
# CONFIG_USB_HIDINPUT_POWERBOOK is not set
CONFIG_USB_HIDDEV=y
# CONFIG_USB_AIPTEK is not set
CONFIG_USB_WACOM=y
# CONFIG_USB_ACECAD is not set
# CONFIG_USB_KBTAB is not set
# CONFIG_USB_POWERMATE is not set
# CONFIG_USB_TOUCHSCREEN is not set
# CONFIG_USB_YEALINK is not set
# CONFIG_USB_XPAD is not set
# CONFIG_USB_ATI_REMOTE is not set
# CONFIG_USB_ATI_REMOTE2 is not set
# CONFIG_USB_KEYSPAN_REMOTE is not set
# CONFIG_USB_APPLETOUCH is not set
# USB Imaging devices
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set
# USB Network Adapters
# CONFIG_USB_CATC is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_USBNET_MII is not set
# CONFIG_USB_USBNET is not set
# CONFIG_USB_MON is not set
# USB port drivers
# USB Serial Converter support
# CONFIG_USB_SERIAL is not set
# USB Miscellaneous drivers
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_ADUTUX is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYPRESS_CY7C63 is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_PHIDGET is not set
# CONFIG_USB_IDMOUSE is not set
# CONFIG_USB_FTDI_ELAN is not set
# CONFIG_USB_APPLEDISPLAY is not set
# CONFIG_USB_SISUSBVGA is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_TEST is not set
# USB DSL modem support
# USB Gadget Support
# CONFIG_USB_GADGET is not set |
_________________
A cow enters a supermarket, does an handstand and dies. (Public toilet graffito) |
|
| Back to top |
|
|
noice
Guru
Joined: 05 Dec 2005
Posts: 473
Location: italia, Ischia
|
| Posted: Thu Apr 05, 2007 2:44 pm Post subject: |
|
|
se puo' servirti questo è il mio | Code: | CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=y
CONFIG_USB_DEVICEFS=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_OHCI_HCD=y
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
CONFIG_USB_UHCI_HCD=y
CONFIG_USB_PRINTER=y
CONFIG_USB_STORAGE=y
CONFIG_USB_HID=y
CONFIG_USB_HIDINPUT=y
CONFIG_USB_MON=y
|
_________________
Noice
when you post remove comments | Code: | | grep -vh '^[[:space:]]*\(#\|$\)' "$@" |
|
|
| Back to top |
|
|
xdarma
l33t
Joined: 08 Dec 2003
Posts: 719
Location: tra veneto e friuli (italy)
|
| Posted: Thu Apr 05, 2007 5:19 pm Post subject: Re: Popup quando si inserisce penna USB |
|
|
| canduc17 wrote: | Ciao.
Ho cercato su google, ma non sono riuscito a trovare l'howto per fare in modo che, quando inserisco una penna USB, si apra un pop-up che mi chieda cosa voglio fare con il dispositivo appena montato (ad esempio aprirlo in una cartella).
Come devo fare? |
Oltre a tutto quello che ti hanno già detto, verifica che in:
Pannello di controllo di KDE -> Configura desktop -> Comportamento -> Icone dei dispositivi
"Mostra le icone dei dispositivi" sia selezionata e che tra i "Tipi di dispositivo da mostrare" sia selezionata "Supporto rimovibile montato".
_________________
proud user of faKeDE-4.7.3 -> back to windowmaker -> moved to LXQt |
|
| Back to top |
|
|
!equilibrium
Bodhisattva
Joined: 06 Jun 2004
Posts: 2109
Location: MI/BG/LC
|
|
| Back to top |
|
|
canduc17
l33t
Joined: 11 Oct 2005
Posts: 795
Location: Ferrara, Italy
|
| Posted: Fri Apr 06, 2007 9:04 am Post subject: |
|
|
Ora in Pannello di controllo di KDE -> Configura desktop -> Comportamento -> Icone dei dispositivi
"Mostra le icone dei dispositivi" è selezionata e tra i "Tipi di dispositivo da mostrare" è selezionata "Supporto rimovibile montato".
Della configurazione di noice per l'USB, mi mancava solo CONFIG_USB_MON; ma anche dopo averlo inserito, non è cambiato nulla, non si apre nessuna finestra quando inserisco la penna...
_________________
A cow enters a supermarket, does an handstand and dies. (Public toilet graffito) |
|
| Back to top |
|
|
Scen
Retired Dev
Joined: 29 Jul 2003
Posts: 2470
Location: Padova, Italy
|
| Posted: Fri Apr 06, 2007 10:04 am Post subject: |
|
|
kdebase-kioslaves è compilato con la use "hal" abilitata? (penso di sì, ma verificare non fa mai male)
Hai controllato che non ci sia qualche problema di librerie corrotte? (non si sa mai anche qua) revdep-rebuild -pv si lamenta di qualcosa?
_________________
I was born in a deep forest/I wish I could live here all my life/I am made from stones and roots/My home, these woods and roads
All my life I loved this sound/Of the woods all around/Eagles flies where the winds blows free
Journey is my destiny |
|
| Back to top |
|
|
canduc17
l33t
Joined: 11 Oct 2005
Posts: 795
Location: Ferrara, Italy
|
| Posted: Fri Apr 06, 2007 10:18 am Post subject: |
|
|
| Code: | candacer canduc # equery uses kdebase-kioslaves
[ Searching for packages matching kdebase-kioslaves... ]
[ Colour Code : set unset ]
[ Legend : Left column (U) - USE flags from make.conf ]
[ : Right column (I) - USE flags packages was installed with ]
[ Found these USE variables for kde-base/kdebase-kioslaves-3.5.5-r1 ]
U I
- + arts : Adds support for aRts: the KDE sound daemon
- - debug : Enable extra debug codepaths, like asserts and extra output. If you want to get meaningful backtraces see http://www.gentoo.org/proj/en/qa/backtraces.xml .
- - elibc_FreeBSD : <unknown>
+ + hal : Enable Hardware Abstraction Layer (HAL) support
- - kdeenablefinal : EXPERIMENTAL: KDE ebuilds will use the enable-final flag, yielding big compilation speedups at the cost of heavy mem usage.
- - kdehiddenvisibility : Makes KDE symbols hidden by default, requires GCC 4.1 (experimental)
- - ldap : Adds LDAP support (Lightweight Directory Access Protocol)
- - openexr : Support for the OpenEXR graphics file format
- - samba : Adds support for SAMBA (Windows File and Printer sharing)
- - xinerama : Add support for the xinerama X11 extension, which allows you to stretch your display across multiple monitors |
| Code: | candacer canduc # revdep-rebuild -pv
Configuring search environment for revdep-rebuild
Checking reverse dependencies...
Packages containing binaries and libraries broken by a package update
will be emerged.
Collecting system binaries and libraries... done.
(/root/.revdep-rebuild.1_files)
Collecting complete LD_LIBRARY_PATH... done.
(/root/.revdep-rebuild.2_ldpath)
Checking dynamic linking consistency...
done.
(/root/.revdep-rebuild.3_rebuild)
Assigning files to ebuilds... Nothing to rebuild
Evaluating package order... done.
(/root/.revdep-rebuild.5_order)
Dynamic linking on your system is consistent... All done. |
_________________
A cow enters a supermarket, does an handstand and dies. (Public toilet graffito) |
|
| Back to top |
|
|
Scen
Retired Dev
Joined: 29 Jul 2003
Posts: 2470
Location: Padova, Italy
|
| Posted: Fri Apr 06, 2007 11:07 am Post subject: |
|
|
Io quando collego la mia pendrive ottengo questo (da dmesg)
| Code: |
usb 1-6: new high speed USB device using ehci_hcd and address 5
usb 1-6: configuration #1 chosen from 1 choice
scsi6 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
scsi 6:0:0:0: Direct-Access SanDisk Cruzer Mini 0.2 PQ: 0 ANSI: 2
SCSI device sdd: 1000944 512-byte hdwr sectors (512 MB)
sdd: Write Protect is off
sdd: Mode Sense: 03 00 00 00
sdd: assuming drive cache: write through
SCSI device sdd: 1000944 512-byte hdwr sectors (512 MB)
sdd: Write Protect is off
sdd: Mode Sense: 03 00 00 00
sdd: assuming drive cache: write through
sdd: sdd1
sd 6:0:0:0: Attached scsi removable disk sdd
usb-storage: device scan complete
|
Siccome non riesco a capire cosa non vada nel tuo sistema, fai così
- Avvia il sistema
- Da console dai dmesg
- Inserisci la pendrive e attendi qualche secondo
- Da un'altra console, ridai dmesg
- incolla i messaggi in più del secondo dmesg rispetto al primo
_________________
I was born in a deep forest/I wish I could live here all my life/I am made from stones and roots/My home, these woods and roads
All my life I loved this sound/Of the woods all around/Eagles flies where the winds blows free
Journey is my destiny |
|
| Back to top |
|
|
canduc17
l33t
Joined: 11 Oct 2005
Posts: 795
Location: Ferrara, Italy
|
| Posted: Fri Apr 06, 2007 11:23 am Post subject: |
|
|
| Code: | usb 4-1: new high speed USB device using ehci_hcd and address 3
usb 4-1: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
scsi 0:0:0:0: Direct-Access VBTM Store 'n' Go 5.00 PQ: 0 ANSI: 0 CCS
SCSI device sda: 1809408 512-byte hdwr sectors (926 MB)
sda: Write Protect is off
sda: Mode Sense: 23 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 1809408 512-byte hdwr sectors (926 MB)
sda: Write Protect is off
sda: Mode Sense: 23 00 00 00
sda: assuming drive cache: write through
sda: sda1
sd 0:0:0:0: Attached scsi removable disk sda
usb-storage: device scan complete |
_________________
A cow enters a supermarket, does an handstand and dies. (Public toilet graffito) |
|
| Back to top |
|
|
Onip
Advocate
Joined: 02 Sep 2004
Posts: 2912
Location: Parma (Italy)
|
| Posted: Fri Apr 06, 2007 11:24 am Post subject: |
|
|
| Scen wrote: |
- Avvia il sistema
- Da console dai dmesg
- Inserisci la pendrive e attendi qualche secondo
- Da un'altra console, ridai dmesg
- incolla i messaggi in più del secondo dmesg rispetto al primo
|
anche
dovrebbe funzionare, o sbaglio? 
_________________
Linux Registered User n. 373835
Titus Lucretius Carus, De Rerum Natura - Tantum religio potuit suadere malorum |
|
| Back to top |
|
|
Scen
Retired Dev
Joined: 29 Jul 2003
Posts: 2470
Location: Padova, Italy
|
| Posted: Fri Apr 06, 2007 11:31 am Post subject: |
|
|
| Onip wrote: | | anche dovrebbe funzionare, o sbaglio? |
Lo so, hai ragione 
Era per avere un elenco di messaggi "pulito", in quanto usando il comando che dici "in corsa" c'è il rischio di avere i messaggi del kernel "sporcati" da altri eventi (o di non vedere tutte le righe).
/me pignolo 
_________________
I was born in a deep forest/I wish I could live here all my life/I am made from stones and roots/My home, these woods and roads
All my life I loved this sound/Of the woods all around/Eagles flies where the winds blows free
Journey is my destiny |
|
| Back to top |
|
|
|
Forum italiano (Italian)
