| View previous topic :: View next topic |
| Author |
Message |
numerodix
l33t
Joined: 18 Jul 2002
Posts: 743
Location: nl.eu
|
 Posted: Sun Mar 23, 2003 1:29 am Post subject: Cannot get network online |
 |
|
I've set up some partitions for Gentoo recently on the same disk WinXP runs on. In order to be able to use the system while compiling, I've done most of the builds in vmware. In order to do that, I compiled both the driver for the vmware ethernet card and the actual adapter on my mainboard into the kernel. In vmware it works fine but when I boot from the physical disk I cannot get the network online.
I also keep getting this message when starting/stopping the net interface but not just then.
| Code: | /usr/sbin/runscript.sh: line 1: ..#: command not found
|
I printed some info I thought might be useful...
| Code: | # lspci
00:00.0 Host bridge: Silicon Integrated Systems [SiS] SiS645DX Host & Memory & AGP Controller
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] SiS 530 Virtual PCI-to-PCI bridge (AGP)
00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS961 [MuTIOL Media IO] (rev 10)
00:02.2 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 07)
00:02.3 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 07)
00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev d0)
00:03.0 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 10/100 Ethernet (rev 90)
00:05.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10)
00:09.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
00:09.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
00:0b.0 Multimedia audio controller: Ensoniq 5880 AudioPCI (rev 04)
01:00.0 VGA compatible controller: nVidia Corporation NV15 [GeForce2 GTS/Pro] (rev a4)
|
| Code: | # dmesg
Linux version 2.4.20-gentoo-r1 (root@cdimage) (gcc version 3.2.2) #1 SMP Thu Mar 20 16:00:47 CET 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fffc000 (usable)
BIOS-e820: 000000001fffc000 - 000000001ffff000 (ACPI data)
BIOS-e820: 000000001ffff000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
511MB LOWMEM available.
ACPI: have wakeup address 0xc0002000
On node 0 totalpages: 131068
zone(0): 4096 pages.
zone(1): 126972 pages.
zone(2): 0 pages.
ACPI: RSDP (v000 ASUS ) @ 0x000f6860
ACPI: RSDT (v001 ASUS P4S533 16944.11825) @ 0x1fffc000
ACPI: FADT (v001 ASUS P4S533 16944.11825) @ 0x1fffc100
ACPI: BOOT (v001 ASUS P4S533 16944.11825) @ 0x1fffc040
ACPI: MADT (v001 ASUS P4S533 16944.11825) @ 0x1fffc080
ACPI: DSDT (v001 ASUS P4S533 00000.04096) @ 0x00000000
ACPI: BIOS passes blacklist
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 Pentium 4(tm) XEON(tm) APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] polarity[0x1] trigger[0x1] lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0])
IOAPIC[0]: Assigned apic_id 2
IOAPIC[0]: apic_id 2, version 0, address 0xfec00000, IRQ 0-23
ACPI: INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x0] trigger[0x1])
ACPI: INT_SRC_OVR (bus[0] irq[0x9] global_irq[0x14] polarity[0x3] trigger[0x3])
Using ACPI (MADT) for SMP configuration information
Kernel command line: root=/dev/hda10
Initializing CPU#0
Detected 2018.115 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 3981.31 BogoMIPS
Memory: 511636k/524272k available (2132k kernel code, 10072k reserved, 613k data, 132k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I cache: 0K, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Hyper-Threading is disabled
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 3febfbff 00000000 00000000 00000000
CPU: Common caps: 3febfbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
CPU: L1 I cache: 0K, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Hyper-Threading is disabled
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 3febfbff 00000000 00000000 00000000
CPU: Common caps: 3febfbff 00000000 00000000 00000000
CPU0: Intel(R) Pentium(R) 4 CPU 2.00GHz stepping 04
per-CPU timeslice cutoff: 1462.33 usecs.
task migration cache decay timeout: 2 msecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Error: only one processor found.
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-21, 2-22, 2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 17.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00178000
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0000
WARNING: unexpected IO-APIC, please mail
to linux-smp@vger.kernel.org
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 0 0 0 0 0 1 1 71
0a 001 01 0 0 0 0 0 1 1 79
0b 001 01 0 0 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 001 01 0 0 0 0 0 1 1 91
0e 001 01 0 0 0 0 0 1 1 99
0f 001 01 0 0 0 0 0 1 1 A1
10 000 00 1 0 0 0 0 0 0 00
11 000 00 1 0 0 0 0 0 0 00
12 000 00 1 0 0 0 0 0 0 00
13 000 00 1 0 0 0 0 0 0 00
14 001 01 1 1 0 1 0 1 1 71
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9-> 0:20
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2017.0671 MHz.
..... host bus clock speed is 100.0883 MHz.
cpu: 0, clocks: 100883, slice: 50441
CPU0<T0:100880,T1:50432,D:7,S:50441,C:100883>
migration_task 0 on cpu=0
ACPI: Subsystem revision 20021122
PCI: PCI BIOS revision 2.10 entry at 0xf15b0, last bus=1
PCI: Using configuration type 1
IOAPIC[0]: Set PCI routing entry (2-9 -> 0x71 -> IRQ 9)
ACPI-0511: *** Info: GPE Block0 defined as GPE0 to GPE15
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: System [ACPI] (supports S0 S1 S4 S5)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 12 14 15, disabled)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15, enabled at IRQ 9)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15, disabled)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15, enabled at IRQ 9)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15, enabled at IRQ 9)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
PCI: Probing PCI hardware
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 10
IOAPIC[0]: Set PCI routing entry (2-23 -> 0xa9 -> IRQ 23)
00:00:02[A] -> 2-23 -> IRQ 23
IOAPIC[0]: Set PCI routing entry (2-22 -> 0xb1 -> IRQ 22)
00:00:02[B] -> 2-22 -> IRQ 22
IOAPIC[0]: Set PCI routing entry (2-21 -> 0xb9 -> IRQ 21)
00:00:02[C] -> 2-21 -> IRQ 21
IOAPIC[0]: Set PCI routing entry (2-20 -> 0xc1 -> IRQ 20)
00:00:02[D] -> 2-20 -> IRQ 20
Pin 2-22 already programmed
IOAPIC[0]: Set PCI routing entry (2-16 -> 0xc9 -> IRQ 16)
00:00:08[A] -> 2-16 -> IRQ 16
IOAPIC[0]: Set PCI routing entry (2-17 -> 0xd1 -> IRQ 17)
00:00:08[B] -> 2-17 -> IRQ 17
IOAPIC[0]: Set PCI routing entry (2-18 -> 0xd9 -> IRQ 18)
00:00:08[C] -> 2-18 -> IRQ 18
IOAPIC[0]: Set PCI routing entry (2-19 -> 0xe1 -> IRQ 19)
00:00:08[D] -> 2-19 -> IRQ 19
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Journalled Block Device driver loaded
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.0a [Flags: R/O].
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller on PCI bus 00 dev 15
SIS5513: detected chipset, but driver not compiled in!
SIS5513: chipset revision 208
SIS5513: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:pio
hda: WDC WD800BB-32CCB0, ATA DISK drive
hdb: IC35L060AVER07-0, ATA DISK drive
hdc: LG CD-RW CED-8120B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=9729/255/63
hdb: 120103200 sectors (61493 MB) w/1916KiB Cache, CHS=7476/255/63
hdc: ATAPI 32X CD-ROM CD-R/RW drive, 8192kB Cache
Uniform CD-ROM driver Revision: 3.12
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 p9 p10 p11 p12 >
/dev/ide/host0/bus0/target1/lun0: p1 < p5 >
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
pcnet32.c:v1.27b 01.10.2002 tsbogend@alpha.franken.de
sis900.c: v1.08.06 9/24/2002
eth0: Realtek RTL8201 PHY transceiver found at address 1.
eth0: Using transceiver found at address 1 as default
eth0: SiS 900 PCI Fast Ethernet at 0xb000, IRQ 22, 00:e0:18:8a:7f:30.
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected SiS 646 chipset
agpgart: AGP aperture is 64M @ 0xe8000000
usb.c: registered new driver hub
uhci.c: USB Universal Host Controller Interface driver v1.1
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 132k freed
Adding Swap: 1028120k swap-space (priority -1)
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,10), internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,11), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
eth0: Media Link On 10mbps full-duplex
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 00000000 00000259
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 00000000 00000260
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 00000000 00000260
eth0: Media Link On 10mbps full-duplex
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 00000000 00000279
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 00000000 00000260
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 00000000 00000260
|
|
|
| Back to top |
|
 |
dma
Guru
Joined: 31 Jan 2003
Posts: 437
Location: Charlotte, NC, USA
|
| Posted: Sun Mar 23, 2003 5:29 am Post subject: |
|
|
Please post the contents of your /etc/conf.d/net file.
I've found that you need to copy /etc/init.d/net.eth0 to /etc/init.d/net.eth1 if you want more than one interface.
Also. I don't have runscript.sh in /usr/sbin/. Mine is in /sbin/. Not sure why this is. |
|
| Back to top |
|
|
numerodix
l33t
Joined: 18 Jul 2002
Posts: 743
Location: nl.eu
|
| Posted: Sun Mar 23, 2003 11:38 am Post subject: |
|
|
Yes, /sbin it is, sorry about that.
I got it working once I got rid of acpi in the kernel, it looks like that was the problem.
Any idea why I'm getting the runscript error thou? |
|
| Back to top |
|
|
numerodix
l33t
Joined: 18 Jul 2002
Posts: 743
Location: nl.eu
|
| Posted: Tue Mar 25, 2003 3:30 am Post subject: |
|
|
| Problem solved, there seems to have been some syntax error in the /etc/init.d/net.X scripts. Merge net-tools and overwrite them, error is gone. |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Networking & Security
