| View previous topic :: View next topic |
| Author |
Message |
complexx
n00b
Joined: 27 Nov 2005
Posts: 13
|
 Posted: Wed Nov 30, 2005 9:01 pm Post subject: [solved] Festplattenproblem |
 |
|
hallo,
wie der Threadname schon sagt hab ich ein Problem mit meiner Festplatte ( Samsung / 160GB / 7200upm).
Alle Aktionen, welche die Festplatte "stärker" beanspruchen, z.B. kopieren einer Daten DVD (4.7GB) dauert 50 min. 
An der Festplatte dürfte es eigentlich nich nicht liegen, da diese vor kurzem noch unter Windows fehlerfrei lief.
Dieser Fehler trat erst nach der Gentoo Installation und Konfiguration auf, wobei der Fehler sicherlich in irgendeiner fehlerhaften Konfiguartion liegt.
Ist jemanden die Fehlerquelle und eine Problemlösung bekannt ?
Danke im vorraus
Last edited by complexx on Fri Dec 02, 2005 2:14 pm; edited 1 time in total |
|
| Back to top |
|
 |
bmuskalla
n00b
Joined: 14 Apr 2005
Posts: 61
Location: Mannheim
|
| Posted: Wed Nov 30, 2005 9:05 pm Post subject: |
|
|
DMA an?
was sagt:
| Code: | | sudo hdparm -d /dev/hda |
? |
|
| Back to top |
|
|
complexx
n00b
Joined: 27 Nov 2005
Posts: 13
|
| Posted: Wed Nov 30, 2005 9:10 pm Post subject: |
|
|
| ne is off |
|
| Back to top |
|
|
m.b.j.
Guru
Joined: 12 Sep 2003
Posts: 407
Location: Germany (Essen)
|
| Posted: Wed Nov 30, 2005 9:27 pm Post subject: |
|
|
Machs an!
man hdparm
_________________
root@mbj # echo "sys-pizza/calzone -tunfish" >> /etc/paludis/use.conf
root@mbj # paludis -i calzone --dl-blocks discard |
|
| Back to top |
|
|
complexx
n00b
Joined: 27 Nov 2005
Posts: 13
|
| Posted: Wed Nov 30, 2005 11:01 pm Post subject: |
|
|
Naja , DMA lässt sich aber nicht aktivieren.
Hab auch schon im Kernel (2.6.13) nachgeschaut und hab vorsichtshalber alles was mit DMA zu tun hat eingebunden.
hdparm -d 1 /dev/hda
/dev/hda:
setting using_dma to 1 (on)
HDIO_SET_DMA failed: Operation not permitted
using_dma = 0 (off)
hdparm -tT
/dev/hda:
Timing cached reads: 1972 MB in 2.00 seconds = 987.91 MB/sec
Timing buffered disk reads: 16 MB in 3.31 seconds = 4.84 MB/sec
hdparm /dev/hda
/dev/hda:
multcount = 16 (on)
IO_support = 1 (32-bit)
unmaskirq = 0 (off)
using_dma = 0 (off)
keepsettings = 0 (off)
readonly = 0 (off)
readahead = 256 (on)
geometry = 19457/255/63, sectors = 160041885696, start = 0
Kann mir jemand da weiterhelfen?.... Bin noch ein noob  |
|
| Back to top |
|
|
phixom
Apprentice
Joined: 07 Jan 2003
Posts: 224
|
| Posted: Thu Dec 01, 2005 8:27 am Post subject: |
|
|
Evtl. keinen oder falschen kerneltreiber für deinen IDE-Controller im Kernel compiliert?
phixom |
|
| Back to top |
|
|
complexx
n00b
Joined: 27 Nov 2005
Posts: 13
|
| Posted: Thu Dec 01, 2005 2:46 pm Post subject: |
|
|
Ich hab ein ASUS K8V-X Board mit via Chipsatz und ich nehme an das ich die richtigen Treiber ausgewählt habe....
<*> ATA/ATAPI/MFM/RLL support x x
x x <*> Enhanced IDE/MFM/RLL disk/cdrom/tape/floppy support
x x --- Please see Documentation/ide.txt for help/info on IDE drives
x x [ ] Support for SATA (deprecated; conflicts with libata SATA driver)
x x [ ] Use old disk-only driver on primary interface
x x [*] Use multi-mode by default x x
x x <*> Include IDE/ATAPI CDROM support x x
x x < > Include IDE/ATAPI TAPE support (EXPERIMENTAL) x x
x x < > Include IDE/ATAPI FLOPPY support x x
x x < > SCSI emulation support x x
x x [ ] IDE Taskfile Access x x
x x --- IDE chipset support/bugfixes x x
x x <*> generic/default IDE chipset support x x
x x [*] CMD640 chipset bugfix/support x x
x x [ ] CMD640 enhanced support x x
x x [ ] PNP EIDE support x x
x x [*] PCI IDE chipset support x x
x x [*] Sharing PCI IDE interrupts support x x
x x [ ] Boot off-board chipsets first support x x
x x <*> Generic PCI IDE Chipset Support x x
x x < > OPTi 82C621 chipset enhanced support (EXPERIMENTAL) x x
x x <*> RZ1000 chipset bugfix/support x x
x x [*] Generic PCI bus-master DMA support x x
x x [*] Force enable legacy 2.0.X HOSTS to use DMA x x
x x [*] Use PCI DMA by default when available x x
x x [ ] Enable DMA only for disks x x
x x < > AEC62XX chipset support x x
x x < > ALI M15x3 chipset support x x
x x <*> AMD and nVidia IDE support x x
x x < > ATI IXP chipset IDE support x x
x x < > CMD64{3|6|8|9} chipset support x x
x x < > Compaq Triflex IDE support x x
x x < > CY82C693 chipset support x x
x x < > Cyrix CS5510/20 MediaGX chipset support (VERY EXPERIMENTAL) x x
x x < > Cyrix/National Semiconductor CS5530 MediaGX chipset support x x
x x < > HPT34X chipset support x x
x x < > HPT36X/37X chipset support x x
x x < > National SCx200 chipset support x x
x x < > Intel PIIXn chipsets support x x
x x < > IT821X IDE support x x
x x < > NS87415 chipset support x x
x x < > PROMISE PDC202{46|62|65|67} support x x
x x < > PROMISE PDC202{68|69|70|71|75|76|77} support x x
x x < > ServerWorks OSB4/CSB5/CSB6 chipsets support
< > Silicon Image chipset support x x
x x < > SiS5513 chipset support x x
x x < > SLC90E66 chipset support x x
x x < > Tekram TRM290 chipset support x x
x x <*> VIA82CXXX chipset support x x
x x [ ] IGNORE word93 Validation BITS |
|
| Back to top |
|
|
Anarcho
Advocate
Joined: 06 Jun 2004
Posts: 2970
Location: Germany
|
| Posted: Thu Dec 01, 2005 2:55 pm Post subject: |
|
|
Entfern diesen hier mal:
| Code: | | x x <*> AMD and nVidia IDE support x x |
Manchmal beissen sich die einzelnen Treiber.
_________________
...it's only Rock'n'Roll, but I like it! |
|
| Back to top |
|
|
complexx
n00b
Joined: 27 Nov 2005
Posts: 13
|
| Posted: Thu Dec 01, 2005 3:19 pm Post subject: |
|
|
So hab den Part kurz entfernt, jedoch hat sich an dem Problem noch nichts geändert.  |
|
| Back to top |
|
|
Anarcho
Advocate
Joined: 06 Jun 2004
Posts: 2970
Location: Germany
|
| Posted: Thu Dec 01, 2005 3:51 pm Post subject: |
|
|
Hast du auch wirklich in den neuen Kernel gebootet? Vielleicht war beim kopieren /boot nicht gemountet.
Ansonsten zeig dochmal die Ausgabe von lspci (eventuell emerge pciutils)
_________________
...it's only Rock'n'Roll, but I like it! |
|
| Back to top |
|
|
Louisdor
Veteran
Joined: 14 Dec 2003
Posts: 1231
Location: im Brandenburgischen
|
| Posted: Thu Dec 01, 2005 4:04 pm Post subject: |
|
|
Nimm mal noch diese raus: | complexx wrote: | Ich hab ein ASUS K8V-X Board mit via Chipsatz ...
<*> RZ1000 chipset bugfix/support |
Brauchst Du den? | Kernel Help wrote: | | The PC-Technologies RZ1000 IDE chip is used on many common 486 and Pentium motherboards, ... |
Und das auch:
| complexx wrote: | | [*] Force enable legacy 2.0.X HOSTS to use DMA |
| Kernel Help wrote: | This is an old piece of lost code from Linux 2.0 Kernels.
Generally say N here. |
Ciao,
aleX!
_________________
"Ich bin ich." |
|
| Back to top |
|
|
Marlo
Veteran
Joined: 26 Jul 2003
Posts: 1591
|
| Posted: Thu Dec 01, 2005 4:08 pm Post subject: |
|
|
Sach ma,
eine
| Quote: | | ( Samsung / 160GB / 7200upm). |
ist doch heutzutage eine S-ATA.
Frage: Hast du eine S-ATA als IDE angeschlossen, also mit dem breiten Kabel und dem alten Stecker?
Ma
_________________
------------------------------------------------------------------
http://radio.garden/ |
|
| Back to top |
|
|
complexx
n00b
Joined: 27 Nov 2005
Posts: 13
|
| Posted: Thu Dec 01, 2005 5:05 pm Post subject: |
|
|
"Ansonsten zeig dochmal die Ausgabe von lspci (eventuell emerge pciutils)"
Wozu ist das gut ?
Das hab ich mittlerweile auch wiederausgenommen. Hatte einfach aus Verzweiflung alles, was mit DMA zu tun hat, aktiviert.
[*] Force enable legacy 2.0.X HOSTS to use DMA
"Frage: Hast du eine S-ATA als IDE angeschlossen, also mit dem breiten Kabel und dem alten Stecker? "
Ne is ne noch ne IDE (SAMSUNG SP1604N).
Features
Formatted Capacity = 160GB
Ultra ATA 133 compatible (Default : UDMA 100 Mode 5)
Fluid Dynamic Bearing Spindle Motor Technology
High Speed Dual Digital Signal Processor (DSP) Based Architecture
ATA S.M.A.R.T. Compliant
ATA Security Mode Feature Set
ATA Host Protected Area Feature Set
ATA Automatic Acoustic Management Feature Set
ATA 48-bit Address Feature Set
ATA Device Configuration Overlay Feature Set
Multi-Burst On-The-Fly Error Correction
NoiseGuard
SilentSeek
hdparm -i /dev/hda
/dev/hda:
Model=SAMSUNG SP1604N, FwRev=TM100-24, SerialNo=S013J20X842705
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=34902, SectSize=554, ECCbytes=4
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive conforms to: (null):
* signifies the current active mode
Nur so nebenbei .... Wie ist es möglich ----> Ultra-DMA/6 (Ultra-ATA/133) 133 MByte / sek. <--- einzurichten, wird ja laut den Features unterstützt ?? |
|
| Back to top |
|
|
Louisdor
Veteran
Joined: 14 Dec 2003
Posts: 1231
Location: im Brandenburgischen
|
| Posted: Thu Dec 01, 2005 5:18 pm Post subject: |
|
|
Mal ne 'doofe' Frage: "Hast Du die Platte auch ordentlich am Board angeschlossen und gejumpert?"
Lach nicht! Das habe ich neulich bei jemanden auch gehabt, da war die Platte als Master gejumpert und am Primary IDE Kabel am Slave Anschluss dran.
Das DVD Laufwerk hatte auch den falschen Anschluss. Sowas kann schon zu 'Verwirrungen' führen.
Ciao,
aleX!
_________________
"Ich bin ich." |
|
| Back to top |
|
|
complexx
n00b
Joined: 27 Nov 2005
Posts: 13
|
| Posted: Thu Dec 01, 2005 5:58 pm Post subject: |
|
|
| Negativ, is alles richtig angeschlossen. |
|
| Back to top |
|
|
Louisdor
Veteran
Joined: 14 Dec 2003
Posts: 1231
Location: im Brandenburgischen
|
| Posted: Thu Dec 01, 2005 6:08 pm Post subject: |
|
|
| Anarcho wrote: | | Ansonsten zeig dochmal die Ausgabe von lspci (eventuell emerge pciutils) |
| complexx wrote: | | Wozu ist das gut ? |
| man lspci wrote: | | lspci is a utility for displaying information about all PCI buses in the system and all devices connected to them. |
Da könnte man mal genau sehen, was Du so alles in Deinem System drin!
Schaden kann so eine Information sicherlich!
Ciao,
aleX!
_________________
"Ich bin ich." |
|
| Back to top |
|
|
complexx
n00b
Joined: 27 Nov 2005
Posts: 13
|
| Posted: Thu Dec 01, 2005 6:23 pm Post subject: |
|
|
00:00.0 Host bridge: VIA Technologies, Inc. VT8385 [K8T800 AGP] Host Bridge (rev 01)
00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI bridge [K8T800/K8T890 South]
00:0a.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gigabit Ethernet Controller (rev 13)
00:0f.0 RAID bus controller: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller (rev 80)
00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800/K8T890 South]
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:00.0 VGA compatible controller: nVidia Corporation NV40.2 [GeForce 6800 LE] (rev a1)
und vielleicht hilft das ja auch weiter:
grep ATA /boot/config*
# CONFIG_X86_MCE_NONFATAL is not set
# CONFIG_ATALK is not set
# CONFIG_ATA_OVER_ETH is not set
# ATA/ATAPI/MFM/RLL support
# CONFIG_BLK_DEV_IDE_SATA is not set
CONFIG_SCSI_SATA=y
# CONFIG_SCSI_SATA_AHCI is not set
# CONFIG_SCSI_SATA_SVW is not set
# CONFIG_SCSI_ATA_PIIX is not set
CONFIG_SCSI_SATA_NV=y
# CONFIG_SCSI_SATA_PROMISE is not set
# CONFIG_SCSI_SATA_QSTOR is not set
CONFIG_SCSI_SATA_SX4=y
# CONFIG_SCSI_SATA_SIL is not set
CONFIG_SCSI_SATA_SIS=y
# CONFIG_SCSI_SATA_ULI is not set
# CONFIG_SCSI_SATA_VIA is not set
# CONFIG_SCSI_SATA_VITESSE is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_USB_STORAGE_DATAFAB is not set |
|
| Back to top |
|
|
deejay
l33t
Joined: 24 Aug 2004
Posts: 983
Location: Hannover, Germany
|
| Posted: Thu Dec 01, 2005 7:00 pm Post subject: |
|
|
habe das gleichn Problem auch, das ich kein DMA aktivieren kann .....
_________________
|
|
| Back to top |
|
|
Louisdor
Veteran
Joined: 14 Dec 2003
Posts: 1231
Location: im Brandenburgischen
|
|
| Back to top |
|
|
complexx
n00b
Joined: 27 Nov 2005
Posts: 13
|
|
| Back to top |
|
|
Louisdor
Veteran
Joined: 14 Dec 2003
Posts: 1231
Location: im Brandenburgischen
|
| Posted: Thu Dec 01, 2005 7:46 pm Post subject: |
|
|
Ich glaube, wenn ich das so lese, dass DU, was Deine lspci Ausgabe sagt, diesen Patch gar nicht brauchst!? Bin mir aber nicht so ganz sicher!
Welchen Kernel hast Du denn eigentlich genommen? sys-kernel/gentoo-sources ?
Ciao,
aleX!
_________________
"Ich bin ich." |
|
| Back to top |
|
|
complexx
n00b
Joined: 27 Nov 2005
Posts: 13
|
| Posted: Thu Dec 01, 2005 7:52 pm Post subject: |
|
|
hab den 2.6.13
Ich liste hier noch mal meine aktuelle cfg auf.
grep ATA /boot/config*
| Code: |
# CONFIG_X86_MCE_NONFATAL is not set
# CONFIG_ATALK is not set
# CONFIG_ATA_OVER_ETH is not set
# ATA/ATAPI/MFM/RLL support
# CONFIG_BLK_DEV_IDE_SATA is not set
CONFIG_SCSI_SATA=y
# CONFIG_SCSI_SATA_AHCI is not set
# CONFIG_SCSI_SATA_SVW is not set
# CONFIG_SCSI_ATA_PIIX is not set
CONFIG_SCSI_SATA_NV=y
# CONFIG_SCSI_SATA_PROMISE is not set
# CONFIG_SCSI_SATA_QSTOR is not set
CONFIG_SCSI_SATA_SX4=y
# CONFIG_SCSI_SATA_SIL is not set
CONFIG_SCSI_SATA_SIS=y
# CONFIG_SCSI_SATA_ULI is not set
# CONFIG_SCSI_SATA_VIA is not set
# CONFIG_SCSI_SATA_VITESSE is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_USB_STORAGE_DATAFAB is not set |
lspci
| Code: | 00:00.0 Host bridge: VIA Technologies, Inc. VT8385 [K8T800 AGP] Host Bridge (rev 01)
00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI bridge [K8T800/K8T890 South]
00:0a.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gigabit Ethernet Controller (rev 13)
00:0f.0 RAID bus controller: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller (rev 80)
00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800/K8T890 South]
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:00.0 VGA compatible controller: nVidia Corporation NV40.2 [GeForce 6800 LE] (rev a1) |
hdparm -i /dev/hda
/dev/hda:
| Code: | Model=SAMSUNG SP1604N, FwRev=TM100-24, SerialNo=S013J20X842705
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=34902, SectSize=554, ECCbytes=4
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive conforms to: (null):
* signifies the current active mode |
dmesg output
| Code: |
Linux version 2.6.13-gentoo-r3 (root@XXX) (gcc version 3.3.6 (Gentoo 3.3.6, ssp-3.3.6-1.0, pie-8.7.8)) #4 SMP Fri Oct 28 17:59:26 Local time zone must be set--see zic
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003ff30000 (usable)
BIOS-e820: 000000003ff30000 - 000000003ff40000 (ACPI data)
BIOS-e820: 000000003ff40000 - 000000003fff0000 (ACPI NVS)
BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
Warning only 896MB will be used.
Use a HIGHMEM enabled kernel.
896MB LOWMEM available.
found SMP MP-table at 000ff780
On node 0 totalpages: 229376
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 ACPIAM ) @ 0x000faac0
ACPI: RSDT (v001 A M I OEMRSDT 0x08000403 MSFT 0x00000097) @ 0x3ff30000
ACPI: FADT (v001 A M I OEMFACP 0x08000403 MSFT 0x00000097) @ 0x3ff30200
ACPI: MADT (v001 A M I OEMAPIC 0x08000403 MSFT 0x00000097) @ 0x3ff30390
ACPI: OEMB (v001 A M I OEMBIOS 0x08000403 MSFT 0x00000097) @ 0x3ff40040
ACPI: DSDT (v001 A0091 A0091006 0x00000006 MSFT 0x0100000d) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:12 APIC version 16
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 40000000:bff80000)
Built 1 zonelists
Kernel command line: BOOT_IMAGE=Gentoo ro root=301
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 2203.312 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 903048k/917504k available (3888k kernel code, 13948k reserved, 1419k data, 248k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 4415.84 BogoMIPS (lpj=8831684)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 078bfbff e1d3fbff 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 078bfbff e1d3fbff 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: After all inits, caps: 078bfbff e1d3fbff 00000000 00000010 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: AMD Athlon(tm) 64 Processor 3200+ stepping 00
Total of 1 processors activated (4415.84 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
Brought up 1 CPUs
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1
PCI: Using configuration type 1
ACPI: Subsystem revision 20050408
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] segment is 0
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 11 devices
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: f3700000-f78fffff
PREFETCH window: e3600000-f35fffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
audit: initializing netlink socket (disabled)
audit(1133473596.156:1): initialized
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.23 [Flags: R/W].
SGI XFS with no debug enabled
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
fakephp: Fake PCI Hot Plug Controller Driver
lp: driver loaded but no devices found
Real Time Clock Driver v1.12
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 64M @ 0xf8000000
[drm] Initialized drm 1.0.0 20040925
vesafb: NVIDIA Corporation, nv40 Board - p212-5 , Chip Rev (OEM: NVIDIA)
vesafb: VBE version: 3.0
vesafb: protected mode interface info at c000:cf20
vesafb: pmi: set display start = c00ccf56, set palette = c00ccfc0
vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da
vesafb: hardware doesn't support DDC transfers
vesafb: monitor limits: vf = 0 Hz, hf = 0 kHz, clk = 0 MHz
vesafb: scrolling: redraw
Console: switching to colour frame buffer device 160x64
vesafb: framebuffer at 0xe8000000, mapped to 0xf8880000, using 24576k, total 131072k
fb0: VESA VGA frame buffer device
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
ACPI: CPU0 (power states: C1[C1])
PNP: PS/2 controller doesn't have AUX irq; using default 0xc
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 112
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP(,...)]
lp0: using parport0 (interrupt-driven).
mice: PS/2 mouse device common for all mice
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 16
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 16
sk98lin: Asus mainboard with buggy VPD? Correcting data.
eth0: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter
PrefPort:A RlmtMode:Check Link State
PPP generic driver version 2.4.2
Linux video capture interface: v1.00
bttv: driver version 0.9.16 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
tvaudio: TV audio decoder + audio/video mux driver
tvaudio: known chips: tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6320,tea6420,tda8425,pic16c54 (PV951),ta8874z
Colour QuickCam for Video4Linux v0.05
input: AT Translated Set 2 keyboard on isa0060/serio0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
hda: SAMSUNG SP1604N, ATA DISK drive
Probing IDE interface ide1...
hdc: ATAPI DVD DD 2X16X4X16, ATAPI CD/DVD-ROM drive
hdd: BENQ DVD-ROM 16X, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 312581808 sectors (160041 MB) w/2048KiB Cache, CHS=19457/255/63
hda: cache flushes supported
hda: hda1 hda2 hda3 < hda5 > hda4
hdc: ATAPI 63X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 50X DVD-ROM drive, 512kB Cache
libata version 1.12 loaded.
ieee1394: raw1394: /dev/raw1394 device initialized
usbmon: debugfs is not available
ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 17
PCI: Via IRQ fixup for 0000:00:10.4, from 5 to 1
ehci_hcd 0000:00:10.4: VIA Technologies, Inc. USB 2.0
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.4: irq 17, io mem 0xf7f00000
ehci_hcd 0000:00:10.4: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 17
PCI: Via IRQ fixup for 0000:00:10.0, from 11 to 1
uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 17, io base 0x0000dc00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 17
PCI: Via IRQ fixup for 0000:00:10.1, from 11 to 1
uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 17, io base 0x0000ec00
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 17
PCI: Via IRQ fixup for 0000:00:10.2, from 10 to 1
uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3)
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 17, io base 0x0000c000
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 17
PCI: Via IRQ fixup for 0000:00:10.3, from 10 to 1
uhci_hcd 0000:00:10.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#4)
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:10.3: irq 17, io base 0x0000c400
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usb 2-1: new low speed USB device using uhci_hcd and address 2
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver hiddev
input: USB HID v1.10 Mouse [B16_b_02 USB-PS/2 Optical Mouse] on usb-0000:00:10.0-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
i2c /dev entries driver
Advanced Linux Sound Architecture Driver Version 1.0.9b (Thu Jul 28 12:20:13 2005 UTC).
ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 18
PCI: Via IRQ fixup for 0000:00:11.5, from 5 to 2
PCI: Setting latency timer of device 0000:00:11.5 to 64
codec_read: codec 0 is not valid [0xfe0000]
codec_read: codec 0 is not valid [0xfe0000]
codec_read: codec 0 is not valid [0xfe0000]
codec_read: codec 0 is not valid [0xfe0000]
ALSA device list:
#0: VIA 8237 with AD1980 at 0xc800, irq 18
oprofile: using NMI interrupt.
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
ip_conntrack version 2.1 (7168 buckets, 57344 max) - 212 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>. http://snowman.net/projects/ipt_recent/
arp_tables: (C) 2002 David S. Miller
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 248k freed
kjournald starting. Commit interval 5 seconds
Adding 1951856k swap on /dev/hda5. Priority:-1 extents:1
EXT3 FS on hda1, internal journal
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 19
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-6629 Wed Nov 3 13:12:51 PST 2004
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on hda4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
eth0: network connection up using port A
speed: 100
autonegotiation: yes
duplex mode: full
flowctrl: symmetric
irq moderation: disabled
scatter-gather: enabled
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
|
|
|
| Back to top |
|
|
complexx
n00b
Joined: 27 Nov 2005
Posts: 13
|
| Posted: Thu Dec 01, 2005 9:04 pm Post subject: |
|
|
| complexx wrote: | hab den 2.6.13
Ich liste hier noch mal meine aktuelle cfg auf.
kernel device drivers
| Code: |
<*> ATA/ATAPI/MFM/RLL support x x
x x <*> Enhanced IDE/MFM/RLL disk/cdrom/tape/floppy support x x
x x --- Please see Documentation/ide.txt for help/info on IDE drives x x
x x [ ] Support for SATA (deprecated; conflicts with libata SATA driver) x x
x x [ ] Use old disk-only driver on primary interface x x
x x <*> Include IDE/ATA-2 DISK support x x
x x [*] Use multi-mode by default x x
x x <*> Include IDE/ATAPI CDROM support x x
x x < > Include IDE/ATAPI TAPE support (EXPERIMENTAL) x x
x x < > Include IDE/ATAPI FLOPPY support x x
x x < > SCSI emulation support x x
x x [ ] IDE Taskfile Access x x
x x --- IDE chipset support/bugfixes x x
x x <*> generic/default IDE chipset support x x
x x [*] CMD640 chipset bugfix/support x x
x x [ ] CMD640 enhanced support x x
x x [ ] PNP EIDE support x x
x x [*] PCI IDE chipset support x x
x x [*] Sharing PCI IDE interrupts support x x
x x [ ] Boot off-board chipsets first support x x
x x <*> Generic PCI IDE Chipset Support x x
x x < > OPTi 82C621 chipset enhanced support (EXPERIMENTAL) x x
x x < > RZ1000 chipset bugfix/support x x
x x [*] Generic PCI bus-master DMA support x x
x x [ ] Force enable legacy 2.0.X HOSTS to use DMA x x
x x [*] Use PCI DMA by default when available x x
x x [ ] Enable DMA only for disks x x
x x < > AEC62XX chipset support x x
x x < > ALI M15x3 chipset support x x
x x < > AMD and nVidia IDE support x x
x x < > ATI IXP chipset IDE support x x
x x < > CMD64{3|6|8|9} chipset support x x
x x < > Compaq Triflex IDE support x x
x x < > CY82C693 chipset support x x
x x < > Cyrix CS5510/20 MediaGX chipset support (VERY EXPERIMENTAL) x x
x x < > Cyrix/National Semiconductor CS5530 MediaGX chipset support x x
x x < > HPT34X chipset support x x
x x < > HPT36X/37X chipset support x x
x x < > National SCx200 chipset support x x
x x < > Intel PIIXn chipsets support x x
x x < > IT821X IDE support x x
x x < > NS87415 chipset support x x
x x < > PROMISE PDC202{46|62|65|67} support x x
x x < > PROMISE PDC202{68|69|70|71|75|76|77} support x x
x x < > ServerWorks OSB4/CSB5/CSB6 chipsets support
< > Silicon Image chipset support x x
x x < > SiS5513 chipset support x x
x x < > SLC90E66 chipset support x x
x x < > Tekram TRM290 chipset support x x
x x < > VIA82CXXX chipset support x x
x x [ ] IGNORE word93 Validation BITS
|
grep ATA /boot/config*
| Code: |
# CONFIG_X86_MCE_NONFATAL is not set
# CONFIG_ATALK is not set
# CONFIG_ATA_OVER_ETH is not set
# ATA/ATAPI/MFM/RLL support
# CONFIG_BLK_DEV_IDE_SATA is not set
CONFIG_SCSI_SATA=y
# CONFIG_SCSI_SATA_AHCI is not set
# CONFIG_SCSI_SATA_SVW is not set
# CONFIG_SCSI_ATA_PIIX is not set
CONFIG_SCSI_SATA_NV=y
# CONFIG_SCSI_SATA_PROMISE is not set
# CONFIG_SCSI_SATA_QSTOR is not set
CONFIG_SCSI_SATA_SX4=y
# CONFIG_SCSI_SATA_SIL is not set
CONFIG_SCSI_SATA_SIS=y
# CONFIG_SCSI_SATA_ULI is not set
# CONFIG_SCSI_SATA_VIA is not set
# CONFIG_SCSI_SATA_VITESSE is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_USB_STORAGE_DATAFAB is not set |
lspci
| Code: | 00:00.0 Host bridge: VIA Technologies, Inc. VT8385 [K8T800 AGP] Host Bridge (rev 01)
00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI bridge [K8T800/K8T890 South]
00:0a.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gigabit Ethernet Controller (rev 13)
00:0f.0 RAID bus controller: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller (rev 80)
00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800/K8T890 South]
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:00.0 VGA compatible controller: nVidia Corporation NV40.2 [GeForce 6800 LE] (rev a1) |
hdparm -i /dev/hda
/dev/hda:
| Code: | Model=SAMSUNG SP1604N, FwRev=TM100-24, SerialNo=S013J20X842705
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=34902, SectSize=554, ECCbytes=4
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive conforms to: (null):
* signifies the current active mode |
dmesg output
| Code: |
Linux version 2.6.13-gentoo-r3 (root@XXX) (gcc version 3.3.6 (Gentoo 3.3.6, ssp-3.3.6-1.0, pie-8.7.8)) #4 SMP Fri Oct 28 17:59:26 Local time zone must be set--see zic
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003ff30000 (usable)
BIOS-e820: 000000003ff30000 - 000000003ff40000 (ACPI data)
BIOS-e820: 000000003ff40000 - 000000003fff0000 (ACPI NVS)
BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
Warning only 896MB will be used.
Use a HIGHMEM enabled kernel.
896MB LOWMEM available.
found SMP MP-table at 000ff780
On node 0 totalpages: 229376
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 ACPIAM ) @ 0x000faac0
ACPI: RSDT (v001 A M I OEMRSDT 0x08000403 MSFT 0x00000097) @ 0x3ff30000
ACPI: FADT (v001 A M I OEMFACP 0x08000403 MSFT 0x00000097) @ 0x3ff30200
ACPI: MADT (v001 A M I OEMAPIC 0x08000403 MSFT 0x00000097) @ 0x3ff30390
ACPI: OEMB (v001 A M I OEMBIOS 0x08000403 MSFT 0x00000097) @ 0x3ff40040
ACPI: DSDT (v001 A0091 A0091006 0x00000006 MSFT 0x0100000d) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:12 APIC version 16
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 40000000:bff80000)
Built 1 zonelists
Kernel command line: BOOT_IMAGE=Gentoo ro root=301
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 2203.312 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 903048k/917504k available (3888k kernel code, 13948k reserved, 1419k data, 248k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 4415.84 BogoMIPS (lpj=8831684)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 078bfbff e1d3fbff 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 078bfbff e1d3fbff 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: After all inits, caps: 078bfbff e1d3fbff 00000000 00000010 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: AMD Athlon(tm) 64 Processor 3200+ stepping 00
Total of 1 processors activated (4415.84 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
Brought up 1 CPUs
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1
PCI: Using configuration type 1
ACPI: Subsystem revision 20050408
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] segment is 0
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 11 devices
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: f3700000-f78fffff
PREFETCH window: e3600000-f35fffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
audit: initializing netlink socket (disabled)
audit(1133473596.156:1): initialized
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.23 [Flags: R/W].
SGI XFS with no debug enabled
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
fakephp: Fake PCI Hot Plug Controller Driver
lp: driver loaded but no devices found
Real Time Clock Driver v1.12
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 64M @ 0xf8000000
[drm] Initialized drm 1.0.0 20040925
vesafb: NVIDIA Corporation, nv40 Board - p212-5 , Chip Rev (OEM: NVIDIA)
vesafb: VBE version: 3.0
vesafb: protected mode interface info at c000:cf20
vesafb: pmi: set display start = c00ccf56, set palette = c00ccfc0
vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da
vesafb: hardware doesn't support DDC transfers
vesafb: monitor limits: vf = 0 Hz, hf = 0 kHz, clk = 0 MHz
vesafb: scrolling: redraw
Console: switching to colour frame buffer device 160x64
vesafb: framebuffer at 0xe8000000, mapped to 0xf8880000, using 24576k, total 131072k
fb0: VESA VGA frame buffer device
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
ACPI: CPU0 (power states: C1[C1])
PNP: PS/2 controller doesn't have AUX irq; using default 0xc
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 112
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP(,...)]
lp0: using parport0 (interrupt-driven).
mice: PS/2 mouse device common for all mice
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 16
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 16
sk98lin: Asus mainboard with buggy VPD? Correcting data.
eth0: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter
PrefPort:A RlmtMode:Check Link State
PPP generic driver version 2.4.2
Linux video capture interface: v1.00
bttv: driver version 0.9.16 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
tvaudio: TV audio decoder + audio/video mux driver
tvaudio: known chips: tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6320,tea6420,tda8425,pic16c54 (PV951),ta8874z
Colour QuickCam for Video4Linux v0.05
input: AT Translated Set 2 keyboard on isa0060/serio0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
hda: SAMSUNG SP1604N, ATA DISK drive
Probing IDE interface ide1...
hdc: ATAPI DVD DD 2X16X4X16, ATAPI CD/DVD-ROM drive
hdd: BENQ DVD-ROM 16X, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 312581808 sectors (160041 MB) w/2048KiB Cache, CHS=19457/255/63
hda: cache flushes supported
hda: hda1 hda2 hda3 < hda5 > hda4
hdc: ATAPI 63X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 50X DVD-ROM drive, 512kB Cache
libata version 1.12 loaded.
ieee1394: raw1394: /dev/raw1394 device initialized
usbmon: debugfs is not available
ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 17
PCI: Via IRQ fixup for 0000:00:10.4, from 5 to 1
ehci_hcd 0000:00:10.4: VIA Technologies, Inc. USB 2.0
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.4: irq 17, io mem 0xf7f00000
ehci_hcd 0000:00:10.4: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 17
PCI: Via IRQ fixup for 0000:00:10.0, from 11 to 1
uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 17, io base 0x0000dc00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 17
PCI: Via IRQ fixup for 0000:00:10.1, from 11 to 1
uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 17, io base 0x0000ec00
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 17
PCI: Via IRQ fixup for 0000:00:10.2, from 10 to 1
uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3)
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 17, io base 0x0000c000
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 17
PCI: Via IRQ fixup for 0000:00:10.3, from 10 to 1
uhci_hcd 0000:00:10.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#4)
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:10.3: irq 17, io base 0x0000c400
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usb 2-1: new low speed USB device using uhci_hcd and address 2
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver hiddev
input: USB HID v1.10 Mouse [B16_b_02 USB-PS/2 Optical Mouse] on usb-0000:00:10.0-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
i2c /dev entries driver
Advanced Linux Sound Architecture Driver Version 1.0.9b (Thu Jul 28 12:20:13 2005 UTC).
ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 18
PCI: Via IRQ fixup for 0000:00:11.5, from 5 to 2
PCI: Setting latency timer of device 0000:00:11.5 to 64
codec_read: codec 0 is not valid [0xfe0000]
codec_read: codec 0 is not valid [0xfe0000]
codec_read: codec 0 is not valid [0xfe0000]
codec_read: codec 0 is not valid [0xfe0000]
ALSA device list:
#0: VIA 8237 with AD1980 at 0xc800, irq 18
oprofile: using NMI interrupt.
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
ip_conntrack version 2.1 (7168 buckets, 57344 max) - 212 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>. http://snowman.net/projects/ipt_recent/
arp_tables: (C) 2002 David S. Miller
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 248k freed
kjournald starting. Commit interval 5 seconds
Adding 1951856k swap on /dev/hda5. Priority:-1 extents:1
EXT3 FS on hda1, internal journal
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 19
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-6629 Wed Nov 3 13:12:51 PST 2004
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on hda4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
eth0: network connection up using port A
speed: 100
autonegotiation: yes
duplex mode: full
flowctrl: symmetric
irq moderation: disabled
scatter-gather: enabled
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
|
|
|
|
| Back to top |
|
|
phixom
Apprentice
Joined: 07 Jan 2003
Posts: 224
|
| Posted: Thu Dec 01, 2005 9:49 pm Post subject: |
|
|
| complexx wrote: |
x x
x x <*> generic/default IDE chipset support x x
x x [*] CMD640 chipset bugfix/support x x
x x [ ] CMD640 enhanced support x x
x x [ ] PNP EIDE support x x
x x [*] PCI IDE chipset support x x
x x [*] Sharing PCI IDE interrupts support x x
x x [ ] Boot off-board chipsets first support x x
x x <*> Generic PCI IDE Chipset Support x x
x x < > OPTi 82C621 chipset enhanced support (EXPERIMENTAL) x x
x x < > RZ1000 chipset bugfix/support x x
x x [*] Generic PCI bus-master DMA support x x
x x [ ] Force enable legacy 2.0.X HOSTS to use DMA x x
x x [*] Use PCI DMA by default when available x x
x x [ ] Enable DMA only for disks x x
|
also den CMD640 brauchst du nicht oder ist der mit drin?
eine von den beiden Optionen , generic/default IDE chipset support bzw. PCI IDE chipset support hat sich bei mir auh mal mit DMA gebissen. Also mal am besten alles deaktvieren, was du nicht wirklich brauchst.
phixom |
|
| Back to top |
|
|
Louisdor
Veteran
Joined: 14 Dec 2003
Posts: 1231
Location: im Brandenburgischen
|
| Posted: Thu Dec 01, 2005 9:49 pm Post subject: |
|
|
| complexx wrote: | hab den 2.6.13
Ich liste hier noch mal meine aktuelle cfg auf.
kernel device drivers
| Code: | [*] CMD640 chipset bugfix/support
< > VIA82CXXX chipset support |
|
Den CMD640 hast Du ja immer noch drin!? Und den VIA82 nicht mehr!?
| complexx wrote: | hdparm -i /dev/hda
/dev/hda:
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
* signifies the current active mode[/code] |
Hm, da steht doch aber, dass udma5 gerade der aktive modus ist!
Und, wozu hast Du denn noch das SATA Zeugs drin?
PS: Was hast Du denn für ein IDE Kabel genommen?
Ciao,
aleX!
_________________
"Ich bin ich." |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Deutsches Forum (German)
