I have 3xNIC but only working two (eth0,eth1)
dmesg:
but sometimes - eth2 is loadedLinux version 2.6.11-gentoo-r9 (root@rob) (gcc version 3.4.3-20050110 (Gentoo 3.4.3.20050110-r2, ssp-3.4.3.20050110-0, pie-8.7.7)) #1 Wed Jun 29 10:36:37 CEST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000006000000 (usable)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
96MB LOWMEM available.
On node 0 totalpages: 24576
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 20480 pages, LIFO batch:5
HighMem zone: 0 pages, LIFO batch:1
DMI not present.
ACPI: Unable to locate RSDP
Allocating PCI resources starting at 06000000 (gap: 06000000:f9ff0000)
Built 1 zonelists
Kernel command line: root=/dev/hda3
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (010c1000)
Initializing CPU#0
PID hash table entries: 512 (order: 9, 8192 bytes)
Detected 401.136 MHz processor.
Using tsc for high-res timesource
Speakup v-2.00 CVS: Wed Mar 2 20:22:02 EST 2005 : initialized
Speakup: loading module "speakup_n"
request_module: runaway loop modprobe speakup_n
Console: colour VGA+ 80x25
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 92676k/98304k available (2919k kernel code, 5212k reserved, 969k data, 192k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 786.43 BogoMIPS (lpj=393216)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Couldn't initialize miscdevice /dev/synth.
CPU: After generic identify, caps: 0183f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0183f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
CPU: After all inits, caps: 0183f9ff 00000000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: Intel Celeron (Mendocino) stepping 05
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb280, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
SCSI subsystem initialized
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Via IRQ fixup
PCI: Using IRQ router VIA [1106/0596] at 0000:00:07.0
Machine check exception polling timer started.
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
inotify device minor=63
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
SGI XFS with large block numbers, no debug enabled
Initializing Cryptographic API
Activating ISA DMA hang workarounds.
Real Time Clock Driver v1.12
Non-volatile memory driver v1.2
vesafb: NVidia, Riva TNT, A5 (OEM: NVidia)
vesafb: VBE version: 3.0
vesafb: protected mode interface info at c000:0253
vesafb: pmi: set display start = c00c028c, set palette = c00c0302
vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da
vesafb: hardware supports DCC2 transfers
vesafb: monitor limits: vf = 75 Hz, hf = 63 kHz, clk = 80 MHz
vesafb: scrolling: redraw
Console: switching to colour frame buffer device 80x30
vesafb: framebuffer at 0xde000000, mapped to 0xc6880000, using 600k, total 4096k
fb0: VESA VGA frame buffer device
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c596a (rev 09) IDE UDMA33 controller on pci0000:00:07.1
ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: QUANTUM FIREBALL SE4.3A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: max request size: 128KiB
hda: 8418816 sectors (4310 MB) w/80KiB Cache, CHS=14848/9/63, UDMA(33)
hda: cache flushes not supported
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3
st: Version 20041025, fixed bufsize 32768, s/g segs 256
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
ip_conntrack version 2.1 (768 buckets, 6144 max) - 212 bytes per conntrack
NET: Registered protocol family 1
NET: Registered protocol family 17
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 192k freed
Adding 250320k swap on /dev/hda2. Priority:-1 extents:1
EXT3 FS on hda3, internal journal
8139too Fast Ethernet driver 0.9.27
PCI: Found IRQ 11 for device 0000:00:09.0
eth0: RealTek RTL8139 at 0xc686e000, 00:11:3b:04:92:18, IRQ 11
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
PCI: Found IRQ 10 for device 0000:00:0a.0
eth1: RealTek RTL8139 at 0xc6870000, 00:11:3b:04:92:05, IRQ 10
eth1: Identified 8139 chip type 'RTL-8100B/8139D'
PCI: Found IRQ 12 for device 0000:00:0b.0
8139too: 0000:00:0b.0: Chip not responding, ignoring board
8139too: probe of 0000:00:0b.0 failed with error -5
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Bridge firewalling registered
device eth1 entered promiscuous mode
eth1: link up, 100Mbps, full-duplex, lpa 0x45E1
eth1: Promiscuous mode enabled.
eth1: Promiscuous mode enabled.
eth1: Promiscuous mode enabled.
eth1: Promiscuous mode enabled.
eth1: Promiscuous mode enabled.
ip_tables: (C) 2000-2002 Netfilter core team
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
Linux version 2.6.11-gentoo-r9 (root@rob) (gcc version 3.4.3-20050110 (Gentoo 3.4.3.20050110-r2, ssp-3.4.3.20050110-0, pie-8.7.7)) #1 Wed Jun 29 10:36:37 CEST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000006000000 (usable)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
96MB LOWMEM available.
On node 0 totalpages: 24576
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 20480 pages, LIFO batch:5
HighMem zone: 0 pages, LIFO batch:1
DMI not present.
ACPI: Unable to locate RSDP
Allocating PCI resources starting at 06000000 (gap: 06000000:f9ff0000)
Built 1 zonelists
Kernel command line: root=/dev/hda3
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (010c1000)
Initializing CPU#0
PID hash table entries: 512 (order: 9, 8192 bytes)
Detected 400.944 MHz processor.
Using tsc for high-res timesource
Speakup v-2.00 CVS: Wed Mar 2 20:22:02 EST 2005 : initialized
Speakup: loading module "speakup_n"
request_module: runaway loop modprobe speakup_n
Console: colour VGA+ 80x25
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 92676k/98304k available (2919k kernel code, 5212k reserved, 969k data, 192k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 788.48 BogoMIPS (lpj=394240)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Couldn't initialize miscdevice /dev/synth.
CPU: After generic identify, caps: 0183f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0183f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
CPU: After all inits, caps: 0183f9ff 00000000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: Intel Celeron (Mendocino) stepping 05
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb280, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
SCSI subsystem initialized
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Via IRQ fixup
PCI: Using IRQ router VIA [1106/0596] at 0000:00:07.0
Machine check exception polling timer started.
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
inotify device minor=63
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
SGI XFS with large block numbers, no debug enabled
Initializing Cryptographic API
Activating ISA DMA hang workarounds.
Real Time Clock Driver v1.12
Non-volatile memory driver v1.2
vesafb: NVidia, Riva TNT, A5 (OEM: NVidia)
vesafb: VBE version: 3.0
vesafb: protected mode interface info at c000:0253
vesafb: pmi: set display start = c00c028c, set palette = c00c0302
vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da
vesafb: hardware supports DCC2 transfers
vesafb: monitor limits: vf = 75 Hz, hf = 63 kHz, clk = 80 MHz
vesafb: scrolling: redraw
Console: switching to colour frame buffer device 80x30
vesafb: framebuffer at 0xde000000, mapped to 0xc6880000, using 600k, total 4096k
fb0: VESA VGA frame buffer device
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c596a (rev 09) IDE UDMA33 controller on pci0000:00:07.1
ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: QUANTUM FIREBALL SE4.3A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: max request size: 128KiB
hda: 8418816 sectors (4310 MB) w/80KiB Cache, CHS=14848/9/63, UDMA(33)
hda: cache flushes not supported
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3
st: Version 20041025, fixed bufsize 32768, s/g segs 256
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
ip_conntrack version 2.1 (768 buckets, 6144 max) - 212 bytes per conntrack
NET: Registered protocol family 1
NET: Registered protocol family 17
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 192k freed
Adding 250320k swap on /dev/hda2. Priority:-1 extents:1
EXT3 FS on hda3, internal journal
8139too Fast Ethernet driver 0.9.27
PCI: Found IRQ 11 for device 0000:00:09.0
eth0: RealTek RTL8139 at 0xc686e000, 00:11:3b:04:92:18, IRQ 11
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
PCI: Found IRQ 10 for device 0000:00:0a.0
eth1: RealTek RTL8139 at 0xc6870000, 00:11:3b:04:92:05, IRQ 10
eth1: Identified 8139 chip type 'RTL-8100B/8139D'
PCI: Found IRQ 12 for device 0000:00:0b.0
8139too: 0000:00:0b.0: unknown chip version, assuming RTL-8139
8139too: 0000:00:0b.0: TxConfig = 0xffffffff
eth2: RealTek RTL8139 at 0xc6872000, fb:db:bf:ff:6f:7f, IRQ 12
eth2: Identified 8139 chip type 'RTL-8139'
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Bridge firewalling registered
device eth1 entered promiscuous mode
eth1: link up, 100Mbps, full-duplex, lpa 0x45E1
eth1: Promiscuous mode enabled.
eth1: Promiscuous mode enabled.
eth1: Promiscuous mode enabled.
eth1: Promiscuous mode enabled.
eth1: Promiscuous mode enabled.
eth2: link up, 100Mbps, full-duplex, lpa 0xFFFF
eth2: Promiscuous mode enabled.
device eth2 entered promiscuous mode
br0: port 1(eth1) entering learning state
eth1: Promiscuous mode enabled.
eth1: Promiscuous mode enabled.
ip_tables: (C) 2000-2002 Netfilter core team
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
br0: topology change detected, propagating
br0: port 1(eth1) entering forwarding state
atkbd.c: Keyboard on isa0060/serio0 reports too many keys pressed.
atkbd.c: Keyboard on isa0060/serio0 reports too many keys pressed.
atkbd.c: Keyboard on isa0060/serio0 reports too many keys pressed.
atkbd.c: Keyboard on isa0060/serio0 reports too many keys pressed.
lsmod:
lspci -vModule Size Used by
sch_ingress 3460 1
sch_sfq 4992 3
cls_u32 6532 4
sch_htb 15232 1
ppp_synctty 7808 0
ppp_async 9088 1
crc_ccitt 1920 1 ppp_async
ppp_generic 19604 6 ppp_synctty,ppp_async
slhc 6528 1 ppp_generic
ipt_REJECT 5120 1
ipt_state 1664 3
iptable_filter 2304 1
ipt_MASQUERADE 2688 1
ipt_REDIRECT 1792 2
iptable_nat 19036 3 ipt_MASQUERADE,ipt_REDIRECT
ip_tables 18304 6 ipt_REJECT,ipt_state,iptable_filter,ipt_MASQUERADE,ipt_REDIRECT,iptable_nat
bridge 43032 0
usbcore 97272 1
8139too 19840 0
mii 4096 1 8139too
0000:00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev 22)
Flags: bus master, medium devsel, latency 0
Memory at d8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 1.0
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP] (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: dc000000-ddffffff
Prefetchable memory behind bridge: de000000-deffffff
0000:00:07.0 ISA bridge: VIA Technologies, Inc. VT82C596 ISA [Mobile South] (rev 09)
Subsystem: VIA Technologies, Inc. VT82C596/A/B PCI to ISA Bridge
Flags: bus master, stepping, medium devsel, latency 0
0000:00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Flags: bus master, medium devsel, latency 32
I/O ports at d000
0000:00:07.3 Host bridge: VIA Technologies, Inc. VT82C596 Power Management
Flags: medium devsel
0000:00:09.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Flags: bus master, medium devsel, latency 32, IRQ 10
I/O ports at d800 [size=256]
Memory at df000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
0000:00:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Flags: bus master, medium devsel, latency 32, IRQ 12
I/O ports at dc00 [size=256]
Memory at df001000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
0000:00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Flags: bus master, medium devsel, latency 32, IRQ 5
I/O ports at e000 [size=256]
Memory at df002000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
0000:01:00.0 VGA compatible controller: nVidia Corporation NV4 [RIVA TNT] (rev 04) (prog-if 00 [VGA])
Subsystem: ASUSTeK Computer Inc. V3400 TNT
Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 11
Memory at dc000000 (32-bit, non-prefetchable) [size=16M]
Memory at de000000 (32-bit, prefetchable) [size=16M]
Capabilities: [60] Power Management version 1
Capabilities: [44] AGP version 1.0
