View previous topic :: View next topic |
Author |
Message |
tdyp Apprentice
Joined: 03 Aug 2006 Posts: 154
|
Posted: Tue Aug 29, 2006 1:55 pm Post subject: [wifi rt2500] probleme de configuration [abandonné] |
|
|
et oui encore un.
probleme, je n ai pas trouver de solution dans les autres cas. voila mon probleme
]bonjour a tous
donc je reviens pour vous exposer mon probleme pour la configuration du ma carte wifi integre ralink rt2500
actuellement je suis sous windows mais je repasserais sous G. des que j aurais exposer mon probleme. ca permettra deja de placer le probleme.
donc j ai vu que sur G. il y avait ndiswrapper. j ai lu qu il permettait d utiliser les pilotes win sous linux. je l installe via emerge, recupere les fichiers, l installe se passe bien mais lorsque l on ajoute le module au noyau: un message d erreur. dmesg me mets un message mais bon j ai virer ndiswrapper, il est encore trop controversé.
ne me laissant pas abattre j ai vu qu il y avait un post traitant de l installation du wifi pour rt2500 facon gentoo... j emerge les fichiers rt2500 (il n est pas masqué pour moi ) ok, je suis la methode ok jusqu a de moment la:
Code: | # modprobe rt2500 ; iwconfig ra0 ; ifconfig ra0
ra0 RT2500 Wireless ESSID:""
Mode:Managed Frequency=2.412 GHz Bit Rate:1 Mb/s
RTS thr:off Fragment thr:off
Encryption key:off
Link Quality=0/100 Signal level=-120 dBm Noise level:-256 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
ra0 Protokoll:Ethernet Hardware Adresse 00:11:22:33:44:55
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:11 Basisadresse:0x8000 |
voila ce que moi j ai:
Code: | # modprobe rt2500 ; iwconfig ra0 ; ifconfig ra0
ra0 no wireless extensions.
ra0 Link encap:Ethernet HWaddr 00:10:60:63:0D:91
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:10 Base address:0x4000 |
de plus ma carte ra0 n apparait que lorsque je l active:
voila ce que me donnait un ifconfig -a seul:
Code: |
eth0 Link encap:Ethernet HWaddr 00:40:D0:86:5B:A4
inet addr:192.168.0.4 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST NOTRAILERS RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2464 errors:0 dropped:0 overruns:0 frame:0
TX packets:2177 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2439223 (2.3 Mb) TX bytes:230327 (224.9 Kb)
Interrupt:7 Base address:0xe000
eth1 Link encap:UNSPEC HWaddr 00-40-D0-01-00-36-CA-16-00-00-00-00-00-00-00-00
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:4 errors:0 dropped:0 overruns:0 frame:0
TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:200 (200.0 b) TX bytes:200 (200.0 b)
|
lorsque je fait:
puii un ifconfig -a
Code: |
# ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:40:D0:86:5B:A4
inet addr:192.168.0.4 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST NOTRAILERS RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2465 errors:0 dropped:0 overruns:0 frame:0
TX packets:2178 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2439593 (2.3 Mb) TX bytes:230393 (224.9 Kb)
Interrupt:7 Base address:0xe000
eth1 Link encap:UNSPEC HWaddr 00-40-D0-01-00-36-CA-16-00-00-00-00-00-00-0 0-00
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:4 errors:0 dropped:0 overruns:0 frame:0
TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:200 (200.0 b) TX bytes:200 (200.0 b)
ra0 Link encap:Ethernet HWaddr 00:10:60:63:0D:91
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:10 Base address:0x4000 |
merci pour votre aide
Last edited by tdyp on Sun Nov 05, 2006 10:32 pm; edited 1 time in total |
|
Back to top |
|
|
man in the hill Veteran
Joined: 15 Dec 2005 Posts: 1552 Location: Madinina
|
Posted: Tue Aug 29, 2006 3:42 pm Post subject: |
|
|
Salut,
j'utilise les pilotes rt2500 ... Il faut que tu rajoutes rt2500 ds le fichier /etc/modules.autoload.d/kernel-2.6 pour un montage automatique au démarrage ensuite tu suis la doc gentoo pour une conf en dhcp ds la fichier /etc/conf.d/net ...
@ + _________________ Get Up and Go ! |
|
Back to top |
|
|
tdyp Apprentice
Joined: 03 Aug 2006 Posts: 154
|
Posted: Tue Aug 29, 2006 7:14 pm Post subject: |
|
|
ok jai rajouter la ligne pour le module
maintenant une question:
a la page 85 du guide gentoo ils indiquent qu on peut a la place de remplir le fichier wireless ( comme de par hasar c est ce que j avais fait...)
donc question voila mon fichier wireless est ce que je peux le rajouter tel quel dans le fichier /etc/conf.d/net
fichier wireless:
Code: | #ma config
#choix su essid -> any pour se connecter a n importe quel essid
wlan_ra0="any"
#clef du essid
key_wlan="s:XXXXXXXXXX"
#mode de connexion auto ad hoc managed ou master
mode_ra0="auto"
#canal de communication
channel_ra0="7"
#autres commandes de configuration
iwconfig_ra0=""
iwpriv_ra0=""
sleep_scan_ra0="2"
sleep_associate_ra0="3"
associate_test_ra0="MAC"
config_wlan=( "dhcp" )
dhcpcd_wlan="-t 3"
|
|
|
Back to top |
|
|
man in the hill Veteran
Joined: 15 Dec 2005 Posts: 1552 Location: Madinina
|
Posted: Tue Aug 29, 2006 8:50 pm Post subject: |
|
|
je pense qu'il n'y a pas de soucis ! A mon avis le système recherche ds ces deux fichiers pour configurer le réseau ... _________________ Get Up and Go ! |
|
Back to top |
|
|
tdyp Apprentice
Joined: 03 Aug 2006 Posts: 154
|
Posted: Tue Aug 29, 2006 11:04 pm Post subject: |
|
|
ok je vais tester mais je vous avoue avoir quelques heu.... disons que je reste sceptique sur le resultat... |
|
Back to top |
|
|
titoucha Advocate
Joined: 21 Jul 2005 Posts: 2374 Location: Genève
|
Posted: Wed Aug 30, 2006 12:52 am Post subject: |
|
|
Il n'y a pas de soucis j'utilises aussi le pilote rt2500 et j'ai ma configuration dans /etc/conf.d/wireless et ça fonctionne. |
|
Back to top |
|
|
tdyp Apprentice
Joined: 03 Aug 2006 Posts: 154
|
Posted: Wed Aug 30, 2006 12:05 pm Post subject: |
|
|
titoucha wrote: | Il n'y a pas de soucis j'utilises aussi le pilote rt2500 et j'ai ma configuration dans /etc/conf.d/wireless et ça fonctionne. | ok je teste donc ca je revien dire ca ti suite |
|
Back to top |
|
|
tdyp Apprentice
Joined: 03 Aug 2006 Posts: 154
|
Posted: Wed Aug 30, 2006 12:59 pm Post subject: |
|
|
bon y a visiblement un truc que je fais mal ou que je ne fait pas
premiere chose j aimerai savoir comment je sais si le fichier wireless est bien pris en compte. si je boot j ai beau faire un ifconfig -a =>ok mais un iwconfig me renvoi toujours un message qui me dit qu il n y a pas d extension pour le sans fil ou un truc comme ca.
de plus dans le guide il explique que la configuration du fichier conf.d/net implique aussi un ajout de ce fichier dans le script de demarrage par rc-update.
probleme le fichier wireless n est pas dans init.d donc aucune possibilite de l ajouter... alors comment faire???? |
|
Back to top |
|
|
titoucha Advocate
Joined: 21 Jul 2005 Posts: 2374 Location: Genève
|
Posted: Wed Aug 30, 2006 6:26 pm Post subject: |
|
|
C'est pas ce fichier qu'il faut mettre dans le rc-update.
Il te faut créer un lien symbolique sur le script /etc/init.d/net.lo Code: | ln -s /etc/init.d/net.lo /etc/init.d/net.ra0 | et c'est ce lien qu'il faut ensuite déclarer avec rc-update pour le démarrage Code: | rc-update add net.ra0 default |
|
|
Back to top |
|
|
dapsaille Advocate
Joined: 02 Aug 2004 Posts: 2366 Location: Paris
|
Posted: Wed Aug 30, 2006 10:36 pm Post subject: |
|
|
Bonjour à toi ..
déja tente une configuration manuelle :p
rmmod rt2500
modprobe rt2500
ifconfig ra0 IPQUIVASBIEN up
route add default gw IPDETONROUTEUR
iwconfig ra0 essid "NOMDETONPOINTACCES"
et teste un ping vers ton routeur .. si c'est bon fait ta configuration comme indiqué précédemment |
|
Back to top |
|
|
tdyp Apprentice
Joined: 03 Aug 2006 Posts: 154
|
Posted: Thu Aug 31, 2006 12:09 pm Post subject: |
|
|
dapsaille wrote: | Bonjour à toi ..
déja tente une configuration manuelle :p
rmmod rt2500
modprobe rt2500
ifconfig ra0 IPQUIVASBIEN up
route add default gw IPDETONROUTEUR
iwconfig ra0 essid "NOMDETONPOINTACCES"
et teste un ping vers ton routeur .. si c'est bon fait ta configuration comme indiqué précédemment | marci je teste ca tisuite!!!!!!!!! |
|
Back to top |
|
|
tdyp Apprentice
Joined: 03 Aug 2006 Posts: 154
|
Posted: Thu Aug 31, 2006 12:23 pm Post subject: |
|
|
ok bon visiblement on avance un peu...
Code: |
localhost ~ # rmmod rt2500
localhost ~ # modprobe rt2500
localhost ~ # ifconfig ra0 192.168.0.3 up
localhost ~ # route add default gw 192.168.0.1
SIOCADDRT: File exists
localhost ~ # iwconfig ra0 essid "wlan"
Cannot read[color=red] /proc/net/wireless[/color]
Error for wireless request "Set ESSID" (8B1A) :
SET failed on device ra0 ; Invalid argument.
|
j ai regarder ce qu etait ce fichier en cherchant, mais je ne l ai pas trouver sur mon poste, doit il etre editer ou creer par un programme... la est le mystere pour moi |
|
Back to top |
|
|
titoucha Advocate
Joined: 21 Jul 2005 Posts: 2374 Location: Genève
|
Posted: Fri Sep 01, 2006 2:03 am Post subject: |
|
|
Il ne faut pas chercher ce fichier car il est créer et si jamais détruit dynamiquement par le système.
Tu en est ou de ton problème car ça ma l'air un peu confus. |
|
Back to top |
|
|
tdyp Apprentice
Joined: 03 Aug 2006 Posts: 154
|
Posted: Fri Sep 01, 2006 11:29 pm Post subject: |
|
|
ben je reste bloqué. en fait iwconfig me mets le meme message. je ne sais pas ou me diriger en fait. le peripherique est je pense bien installé mais pas de detection de ssid et une config incertaine... :s |
|
Back to top |
|
|
man in the hill Veteran
Joined: 15 Dec 2005 Posts: 1552 Location: Madinina
|
Posted: Sat Sep 02, 2006 12:01 am Post subject: |
|
|
Salut,
Si tu essais cela ds /etc/conf.d/net
Code: |
modules=( "iwconfig" )
config_ra0=( "dhcp" )
essid_ra0="ESSID"
channel_ra0="le canal "
|
@ + _________________ Get Up and Go ! |
|
Back to top |
|
|
tdyp Apprentice
Joined: 03 Aug 2006 Posts: 154
|
Posted: Thu Sep 07, 2006 2:43 am Post subject: |
|
|
man in the hill wrote: | Salut,
Si tu essais cela ds /etc/conf.d/net
Code: |
modules=( "iwconfig" )
config_ra0=( "dhcp" )
essid_ra0="ESSID"
channel_ra0="le canal "
|
@ + |
dsl pour le retard, je teste ca et reviens rendre compte |
|
Back to top |
|
|
tdyp Apprentice
Joined: 03 Aug 2006 Posts: 154
|
Posted: Thu Sep 07, 2006 3:38 am Post subject: |
|
|
bon j ai rentré ce que tu viens de me donner comme info:
pareil chou blanc!
Code: |
localhost ~ # ifconfig
eth0 Link encap:Ethernet HWaddr 00:40:D0:86:5B:A4
inet addr:192.168.0.4 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST NOTRAILERS RUNNING MULTICAST MTU:1500 Metric:1
RX packets:238 errors:0 dropped:0 overruns:0 frame:0
TX packets:267 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:76099 (74.3 Kb) TX bytes:26442 (25.8 Kb)
Interrupt:7 Base address:0xe000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:4 errors:0 dropped:0 overruns:0 frame:0
TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:200 (200.0 b) TX bytes:200 (200.0 b)
localhost ~ # iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
eth1 no wireless extensions.
ra0 no wireless extensions.
localhost ~ #
| une autre idee??? |
|
Back to top |
|
|
titoucha Advocate
Joined: 21 Jul 2005 Posts: 2374 Location: Genève
|
Posted: Thu Sep 07, 2006 5:08 am Post subject: |
|
|
Regarde aussi avec le programme RaConfig2500 c'est un interface graphique qui modifie le fichier /etc/Wireless/RT2500STA/RT2500STA.dat qui est utilisé par le module rt2500 lors de sont lancement et j'ai constaté que si celui-ci n'était pas correctement renseigné le module ne fonctionnait pas. |
|
Back to top |
|
|
tdyp Apprentice
Joined: 03 Aug 2006 Posts: 154
|
Posted: Fri Sep 08, 2006 4:16 pm Post subject: |
|
|
voila j ai essayer de lancer RaConfig2500 et voila ce que j ai recolté:
http://img373.imageshack.us/my.php?image=screenshot1qk7.png
j ai lu dans un post qu il fallait rajouter le "&" a la fin de la commande ... ce que j ai fait... resultat:
http://img442.imageshack.us/my.php?image=screenshot2zr4.png
ps: si les photos sont trop petites dites moi je reediterai
donc je pense que meme si j ai tout bien fait... en fait la carte n est meme pas installé cependant quand je fais un lshw j ai ceci:
Code: |
*-network:0 UNCLAIMED
description: Network controller
product: RT2500 802.11g Cardbus/mini-PCI
vendor: RaLink
physical id: 15
bus info: pci@00:15.0
version: 01
width: 32 bits
clock: 33MHz
capabilities: bus_master cap_list
resources: iomemory:d0008000-d0009fff irq:10 |
ou plus loin
Code: | -network:0
description: Ethernet interface
product: RT2500 802.11g Cardbus/mini-PCI
vendor: RaLink
physical id: 15
bus info: pci@00:15.0
logical name: ra0
version: 01
serial: 00:10:60:63:0d:91
width: 32 bits
clock: 33MHz
capabilities: bus_master cap_list ethernet physical
configuration: broadcast=yes driver=rt2500 multicast=yes
resources: iomemory:d0008000-d0009fff irq:10 |
donc le je ne sais plus trop quoi penser.... |
|
Back to top |
|
|
titoucha Advocate
Joined: 21 Jul 2005 Posts: 2374 Location: Genève
|
Posted: Sat Sep 09, 2006 2:27 am Post subject: |
|
|
Je te donnes le contenu de mon fichier /etc/Wireless/RT2500STA/RT2500STA.dat
Code: | # Copy this file to /etc/Wireless/RT2500STA/RT2500STA.dat
# This file is a binary file and will be read on loading rt2500.o module.
# Use "vi -b RT2500STA.dat" to modify settings according to your need.
[Default]
AdhocOfdm=0
CountryRegion=0
WirelessMode=0
TXBurst=0
TurboRate=0
BGProtection=0
ShortSlot=0
TxRate=0
PSMode=CAM
SSID=XXXXXXXXXX <---------là ton ESSID
Channel=10
DefaultKeyID=1
Key1=YYYYYYYYYYYY <------ là ta clef en hexadécimal
PSMode=CAM
ProfileID=
NetworkType=Infra
PreambleType=Long
RTSThreshold=1650799160
FragThreshold=1630680931
|
je t'ai mis les endrois ou il fallait remplir quelque chose, j'ai mis pour du WEP car je n'ai pas réussi à faire passer le WPA. |
|
Back to top |
|
|
tdyp Apprentice
Joined: 03 Aug 2006 Posts: 154
|
Posted: Sun Sep 10, 2006 9:42 pm Post subject: |
|
|
merci quand meme je vais tenter. mais c est dommage, je vais devoir reconfigurer mon wlan... bref je teste et je reviens dire des nouvelles. si quelqu un a tout hasard a une config pour du wpa ca serait bien urbain |
|
Back to top |
|
|
titoucha Advocate
Joined: 21 Jul 2005 Posts: 2374 Location: Genève
|
Posted: Mon Sep 11, 2006 12:00 am Post subject: |
|
|
Une fois que l'interface monte tu peux facilement configurer le Wpa avec l'interface graphique. |
|
Back to top |
|
|
tdyp Apprentice
Joined: 03 Aug 2006 Posts: 154
|
Posted: Mon Sep 11, 2006 11:55 am Post subject: |
|
|
j avais vu sur un topic, qu une personne avait reussi a configurer son wifi en editant son fichier .dat effectivement. mais ce que j aimerais savoir c est malgré mes erreurs, l edition de ce fichier sera t il necessaire...? je l espere... |
|
Back to top |
|
|
titoucha Advocate
Joined: 21 Jul 2005 Posts: 2374 Location: Genève
|
Posted: Tue Sep 12, 2006 1:09 am Post subject: |
|
|
tdyp wrote: | j avais vu sur un topic, qu une personne avait reussi a configurer son wifi en editant son fichier .dat effectivement. mais ce que j aimerais savoir c est malgré mes erreurs, l edition de ce fichier sera t il necessaire...? je l espere... |
Pas trop bien compris où tu veux en venir, mais oui tu peux tout à fait l'éditer ce fichier |
|
Back to top |
|
|
tdyp Apprentice
Joined: 03 Aug 2006 Posts: 154
|
Posted: Thu Sep 14, 2006 7:53 pm Post subject: |
|
|
titoucha wrote: | Je te donnes le contenu de mon fichier /etc/Wireless/RT2500STA/RT2500STA.dat
Code: | # Copy this file to /etc/Wireless/RT2500STA/RT2500STA.dat
# This file is a binary file and will be read on loading rt2500.o module.
# Use "vi -b RT2500STA.dat" to modify settings according to your need.
[Default]
AdhocOfdm=0
CountryRegion=0
WirelessMode=0
TXBurst=0
TurboRate=0
BGProtection=0
ShortSlot=0
TxRate=0
PSMode=CAM
SSID=XXXXXXXXXX <---------là ton ESSID
Channel=10
DefaultKeyID=1
Key1=YYYYYYYYYYYY <------ là ta clef en hexadécimal
PSMode=CAM
ProfileID=
NetworkType=Infra
PreambleType=Long
RTSThreshold=1650799160
FragThreshold=1630680931
|
je t'ai mis les endrois ou il fallait remplir quelque chose, j'ai mis pour du WEP car je n'ai pas réussi à faire passer le WPA. |
j ai copier ton fichier. j ai monté l interface. j ai relancé RaConfig2500
et pareil "device driver not found"... vous savez quoi... j ai beau avoir du wifi sur ce maudit portable je reste et prefere tout de meme l ethernet... je veux bien continuer mais je pense qu a la longue je vais rester en ethernet. |
|
Back to top |
|
|
|