Gentoo Forums
Gentoo Forums
Gentoo Forums
Quick Search: in
Sony Clie Not talking to me..
View unanswered posts
View posts from last 24 hours

 
Reply to topic    Gentoo Forums Forum Index Kernel & Hardware
View previous topic :: View next topic  
Author Message
67comet
Apprentice
Apprentice


Joined: 29 Oct 2004
Posts: 256
Location: Kadena AB, Okinawa Japan

PostPosted: Wed Dec 29, 2004 2:43 pm    Post subject: Sony Clie Not talking to me.. Reply with quote

I've bounced around the forums, talked a few in IRC #gentoo, and still have made no headway with my Sony Clie since early December.

I recompiled my kenrel (gentoo-dev-sources-2.6.9-r1 AND 2.6.10-r1) with all the USB stuff that looked familure/usefull, and needed (I have yet to see anything about "visor" I see that around the forums, but not in genkernel --menuconfig all).

When I dmesg I see a little about Palm Sony at the end mainly. Here is my dmesg with the Sony hooked up to the usb port.

Code:

# dmesg
power switching (usb 1.0)
hub 3-0:1.0: individual port over-current protection
hub 3-0:1.0: power on to power good time: 2ms
hub 3-0:1.0: local power source is good
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x301
usb 1-2: new low speed USB device using address 2
usb 1-2: skipped 1 descriptor after interface
usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-2: default language 0x0409
usb 1-2: Product: USB Mouse
usb 1-2: Manufacturer: Logitech
usb 1-2: hotplug
usb 1-2: adding 1-2:1.0 (config #1, interface 0)
usb 1-2:1.0: hotplug
usbcore: registered new driver usbmouse
drivers/usb/input/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
usbmouse 1-2:1.0: usb_probe_interface
usbmouse 1-2:1.0: usb_probe_interface - got id
input: Logitech USB Mouse on usb-0000:00:1d.0-2
ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 10 (level, low) -> IRQ 10
ehci_hcd 0000:00:1d.7: Intel Corp. 82801DB/DBM (ICH4/ICH4-M) USB 2.0 EHCI Controller
ehci_hcd 0000:00:1d.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6
ehci_hcd 0000:00:1d.7: reset hcc_params 6871 thresh 7 uframes 1024 64 bit addr
ehci_hcd 0000:00:1d.7: capability 0001 at 68
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 10, pci mem e19ecc00
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: init command 010001 (park)=0 ithresh=1 period=1024 RUN
ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
ehci_hcd 0000:00:1d.7: supports USB remote wakeup
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: default language 0x0409
usb usb4: Product: Intel Corp. 82801DB/DBM (ICH4/ICH4-M) USB 2.0 EHCI Controller
usb usb4: Manufacturer: Linux 2.6.9-gentoo-r1 ehci_hcd
usb usb4: SerialNumber: 0000:00:1d.7
usb usb4: hotplug
usb usb4: adding 4-0:1.0 (config #1, interface 0)
usb 4-0:1.0: hotplug
hub 4-0:1.0: usb_probe_interface
hub 4-0:1.0: usb_probe_interface - got id
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
hub 4-0:1.0: standalone hub
hub 4-0:1.0: ganged power switching
hub 4-0:1.0: individual port over-current protection
hub 4-0:1.0: Single TT
hub 4-0:1.0: TT requires at most 8 FS bit times
hub 4-0:1.0: power on to power good time: 20ms
hub 4-0:1.0: local power source is good
hub 4-0:1.0: enabling power on all ports
uhci_hcd 0000:00:1d.0: port 2 portsc 008a
hub 1-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
usb 1-2: USB disconnect, address 2
usb 1-2: usb_disable_device nuking all URBs
usb 1-2: unregistering interface 1-2:1.0
usb 1-2:1.0: hotplug
usb 1-2: unregistering device
usb 1-2: hotplug
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
ehci_hcd 0000:00:1d.7: GetStatus port 2 status 001403 POWER sig=k  CSC CONNECT
hub 4-0:1.0: port 2, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:1d.7: port 2 low speed --> companion
ehci_hcd 0000:00:1d.7: GetStatus port 2 status 003002 POWER OWNER sig=se0  CSC
uhci_hcd 0000:00:1d.0: port 2 portsc 01a3
hub 1-0:1.0: port 2, status 0301, change 0001, 1.5 Mb/s
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x301
usb 1-2: new low speed USB device using address 3
usb 1-2: skipped 1 descriptor after interface
usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-2: default language 0x0409
usb 1-2: Product: USB Mouse
usb 1-2: Manufacturer: Logitech
usb 1-2: hotplug
usb 1-2: adding 1-2:1.0 (config #1, interface 0)
usb 1-2:1.0: hotplug
usbmouse 1-2:1.0: usb_probe_interface
usbmouse 1-2:1.0: usb_probe_interface - got id
input: Logitech USB Mouse on usb-0000:00:1d.0-2
uhci_hcd 0000:00:1d.1: suspend_hc
uhci_hcd 0000:00:1d.2: suspend_hc
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
e100: eth0: e100_watchdog: link up, 100Mbps, half-duplex
parport0: PC-style at 0x378 (0x778) [PCSPP(,...)]
parport0: irq 7 detected
lp0: using parport0 (polling).
NVRM: not using NVAGP, AGPGART is loaded!!
NVRM: not using NVAGP, AGPGART is loaded!!
NVRM: not using NVAGP, AGPGART is loaded!!
spurious 8259A interrupt: IRQ7.
NVRM: not using NVAGP, AGPGART is loaded!!
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 001803 POWER sig=j  CSC CONNECT
hub 4-0:1.0: port 3, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x501
hub 4-0:1.0: port 3 not reset yet, waiting 50ms
ehci_hcd 0000:00:1d.7: port 3 full speed --> companion
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 003801 POWER OWNER sig=j  CONNECT
uhci_hcd 0000:00:1d.1: wakeup_hc
uhci_hcd 0000:00:1d.1: port 1 portsc 0083
hub 2-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
uhci_hcd 0000:00:1d.1: CTRL: TypeReq=0x2301 val=0x2 idx=0x0 len=0 ==> -32
usb 2-1: new full speed USB device using address 2
usb 2-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-1: default language 0x0409
usb 2-1: Product: Palm Handheld
usb 2-1: Manufacturer: Sony
usb 2-1: hotplug
usb 2-1: adding 2-1:1.0 (config #1, interface 0)
usb 2-1:1.0: hotplug
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 001002 POWER sig=se0  CSC
hub 4-0:1.0: port 3, status 0100, change 0001, 12 Mb/s
hub 4-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:1d.1: port 1 portsc 008a
hub 2-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
usb 2-1: USB disconnect, address 2
usb 2-1: usb_disable_device nuking all URBs
usb 2-1: unregistering interface 2-1:1.0
usb 2-1:1.0: hotplug
usb 2-1: unregistering device
usb 2-1: hotplug
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:1d.1: suspend_hc
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 001803 POWER sig=j  CSC CONNECT
hub 4-0:1.0: port 3, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x501
hub 4-0:1.0: port 3 not reset yet, waiting 50ms
ehci_hcd 0000:00:1d.7: port 3 full speed --> companion
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 003801 POWER OWNER sig=j  CONNECT
uhci_hcd 0000:00:1d.1: wakeup_hc
uhci_hcd 0000:00:1d.1: port 1 portsc 0083
hub 2-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
uhci_hcd 0000:00:1d.1: CTRL: TypeReq=0x2301 val=0x2 idx=0x0 len=0 ==> -32
usb 2-1: new full speed USB device using address 3
usb 2-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-1: default language 0x0409
usb 2-1: Product: Palm Handheld
usb 2-1: Manufacturer: Sony
usb 2-1: hotplug
usb 2-1: adding 2-1:1.0 (config #1, interface 0)
usb 2-1:1.0: hotplug
uhci_hcd 0000:00:1d.1: port 1 portsc 008a
hub 2-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
usb 2-1: USB disconnect, address 3
usb 2-1: usb_disable_device nuking all URBs
usb 2-1: unregistering interface 2-1:1.0
usb 2-1:1.0: hotplug
usb 2-1: unregistering device
usb 2-1: hotplug
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 001002 POWER sig=se0  CSC
hub 4-0:1.0: port 3, status 0100, change 0001, 12 Mb/s
hub 4-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:1d.1: suspend_hc
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 001803 POWER sig=j  CSC CONNECT
hub 4-0:1.0: port 3, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x501
hub 4-0:1.0: port 3 not reset yet, waiting 50ms
ehci_hcd 0000:00:1d.7: port 3 full speed --> companion
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 003801 POWER OWNER sig=j  CONNECT
uhci_hcd 0000:00:1d.1: wakeup_hc
uhci_hcd 0000:00:1d.1: port 1 portsc 0083
hub 2-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
uhci_hcd 0000:00:1d.1: CTRL: TypeReq=0x2301 val=0x2 idx=0x0 len=0 ==> -32
usb 2-1: new full speed USB device using address 4
usb 2-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-1: default language 0x0409
usb 2-1: Product: Palm Handheld
usb 2-1: Manufacturer: Sony
usb 2-1: hotplug
usb 2-1: adding 2-1:1.0 (config #1, interface 0)
usb 2-1:1.0: hotplug
uhci_hcd 0000:00:1d.1: uhci_result_control: failed with status 440000
[df24c240] link (1f24c1e2) element (1e751040)
  0: [de751040] link (1e751080) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=4, PID=2d(SETUP) (buf=1b605a40)
  1: [de751080] link (1e7510c0) e3 SPD Active Length=0 MaxLen=f DT1 EndPt=0 Dev=4, PID=69(IN) (buf=01687e80)
  2: [de7510c0] link (1e751100) e3 SPD Active Length=0 MaxLen=f DT0 EndPt=0 Dev=4, PID=69(IN) (buf=01687e90)
  3: [de751100] link (1e751140) e3 SPD Active Length=0 MaxLen=f DT1 EndPt=0 Dev=4, PID=69(IN) (buf=01687ea0)
  4: [de751140] link (1e751180) e3 SPD Active Length=0 MaxLen=f DT0 EndPt=0 Dev=4, PID=69(IN) (buf=01687eb0)
  5: [de751180] link (1e7511c0) e3 SPD Active Length=0 MaxLen=f DT1 EndPt=0 Dev=4, PID=69(IN) (buf=01687ec0)
  6: [de7511c0] link (1e751200) e3 SPD Active Length=0 MaxLen=f DT0 EndPt=0 Dev=4, PID=69(IN) (buf=01687ed0)
  7: [de751200] link (1e751240) e3 SPD Active Length=0 MaxLen=f DT1 EndPt=0 Dev=4, PID=69(IN) (buf=01687ee0)
  8: [de751240] link (1e751280) e3 SPD Active Length=0 MaxLen=f DT0 EndPt=0 Dev=4, PID=69(IN) (buf=01687ef0)
  9: [de751280] link (1e7512c0) e3 SPD Active Length=0 MaxLen=f DT1 EndPt=0 Dev=4, PID=69(IN) (buf=01687f00)
  10: [de7512c0] link (1e751300) e3 SPD Active Length=0 MaxLen=f DT0 EndPt=0 Dev=4, PID=69(IN) (buf=01687f10)
[skipped 6 active TD's]
  17: [de751480] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=4, PID=e1(OUT) (buf=00000000)

uhci_hcd 0000:00:1d.1: uhci_result_control: failed with status 440000
[df24c270] link (1f24c1e2) element (1e7514c0)
  0: [de7514c0] link (1e751500) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=4, PID=2d(SETUP) (buf=1b605a40)
  1: [de751500] link (1e751540) e3 SPD Active Length=0 MaxLen=1 DT1 EndPt=0 Dev=4, PID=69(IN) (buf=01687e80)
  2: [de751540] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=4, PID=e1(OUT) (buf=00000000)

uhci_hcd 0000:00:1d.1: uhci_result_control: failed with status 440000
[df24c240] link (1f24c1e2) element (1e751040)
  0: [de751040] link (1e751080) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=4, PID=2d(SETUP) (buf=1b605a40)
  1: [de751080] link (1e7510c0) e3 SPD Active Length=0 MaxLen=f DT1 EndPt=0 Dev=4, PID=69(IN) (buf=01687e80)
  2: [de7510c0] link (1e751100) e3 SPD Active Length=0 MaxLen=f DT0 EndPt=0 Dev=4, PID=69(IN) (buf=01687e90)
  3: [de751100] link (1e751140) e3 SPD Active Length=0 MaxLen=f DT1 EndPt=0 Dev=4, PID=69(IN) (buf=01687ea0)
  4: [de751140] link (1e751180) e3 SPD Active Length=0 MaxLen=f DT0 EndPt=0 Dev=4, PID=69(IN) (buf=01687eb0)
  5: [de751180] link (1e7511c0) e3 SPD Active Length=0 MaxLen=f DT1 EndPt=0 Dev=4, PID=69(IN) (buf=01687ec0)
  6: [de7511c0] link (1e751200) e3 SPD Active Length=0 MaxLen=f DT0 EndPt=0 Dev=4, PID=69(IN) (buf=01687ed0)
  7: [de751200] link (1e751240) e3 SPD Active Length=0 MaxLen=f DT1 EndPt=0 Dev=4, PID=69(IN) (buf=01687ee0)
  8: [de751240] link (1e751280) e3 SPD Active Length=0 MaxLen=f DT0 EndPt=0 Dev=4, PID=69(IN) (buf=01687ef0)
  9: [de751280] link (1e7512c0) e3 SPD Active Length=0 MaxLen=f DT1 EndPt=0 Dev=4, PID=69(IN) (buf=01687f00)
  10: [de7512c0] link (1e751300) e3 SPD Active Length=0 MaxLen=f DT0 EndPt=0 Dev=4, PID=69(IN) (buf=01687f10)
[skipped 6 active TD's]
  17: [de751480] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=4, PID=e1(OUT) (buf=00000000)

uhci_hcd 0000:00:1d.1: uhci_result_control: failed with status 440000
[df24c270] link (1f24c1e2) element (1e7514c0)
  0: [de7514c0] link (1e751500) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=4, PID=2d(SETUP) (buf=1b605a40)
  1: [de751500] link (1e751540) e3 SPD Active Length=0 MaxLen=1 DT1 EndPt=0 Dev=4, PID=69(IN) (buf=01687e80)
  2: [de751540] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=4, PID=e1(OUT) (buf=00000000)

ehci_hcd 0000:00:1d.7: GetStatus port 3 status 001002 POWER sig=se0  CSC
hub 4-0:1.0: port 3, status 0100, change 0001, 12 Mb/s
hub 4-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:1d.1: port 1 portsc 008a
hub 2-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
usb 2-1: USB disconnect, address 4
usb 2-1: usb_disable_device nuking all URBs
usb 2-1: unregistering interface 2-1:1.0
usb 2-1:1.0: hotplug
usb 2-1: unregistering device
usb 2-1: hotplug
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:1d.1: suspend_hc
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 001803 POWER sig=j  CSC CONNECT
hub 4-0:1.0: port 3, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x501
hub 4-0:1.0: port 3 not reset yet, waiting 50ms
ehci_hcd 0000:00:1d.7: port 3 full speed --> companion
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 003801 POWER OWNER sig=j  CONNECT
uhci_hcd 0000:00:1d.1: wakeup_hc
uhci_hcd 0000:00:1d.1: port 1 portsc 0083
hub 2-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
uhci_hcd 0000:00:1d.1: CTRL: TypeReq=0x2301 val=0x2 idx=0x0 len=0 ==> -32
usb 2-1: new full speed USB device using address 5
usb 2-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-1: default language 0x0409
usb 2-1: Product: Palm Handheld
usb 2-1: Manufacturer: Sony
usb 2-1: hotplug
usb 2-1: adding 2-1:1.0 (config #1, interface 0)
usb 2-1:1.0: hotplug
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 001002 POWER sig=se0  CSC
hub 4-0:1.0: port 3, status 0100, change 0001, 12 Mb/s
hub 4-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:1d.1: port 1 portsc 008a
hub 2-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
usb 2-1: USB disconnect, address 5
usb 2-1: usb_disable_device nuking all URBs
usb 2-1: unregistering interface 2-1:1.0
usb 2-1:1.0: hotplug
usb 2-1: unregistering device
usb 2-1: hotplug
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:1d.1: suspend_hc
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 001803 POWER sig=j  CSC CONNECT
hub 4-0:1.0: port 3, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x501
hub 4-0:1.0: port 3 not reset yet, waiting 50ms
ehci_hcd 0000:00:1d.7: port 3 full speed --> companion
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 003801 POWER OWNER sig=j  CONNECT
uhci_hcd 0000:00:1d.1: wakeup_hc
uhci_hcd 0000:00:1d.1: port 1 portsc 0083
hub 2-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
uhci_hcd 0000:00:1d.1: CTRL: TypeReq=0x2301 val=0x2 idx=0x0 len=0 ==> -32
usb 2-1: new full speed USB device using address 6
usb 2-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-1: default language 0x0409
usb 2-1: Product: Palm Handheld
usb 2-1: Manufacturer: Sony
usb 2-1: hotplug
usb 2-1: adding 2-1:1.0 (config #1, interface 0)
usb 2-1:1.0: hotplug


Down there at the end is what I get when I've got "HotSync" operating on the Palm when I dmesg.

When I do a:
Code:

$ tail -f /var/log/messages

Dec 29 09:20:16 localhost ehci_hcd 0000:00:1d.7: GetStatus port 3 status 001803 POWER sig=j  CSC CONNECT
Dec 29 09:20:16 localhost hub 4-0:1.0: port 3, status 0501, change 0001, 480 Mb/s
Dec 29 09:20:16 localhost hub 4-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x501
Dec 29 09:20:16 localhost hub 4-0:1.0: port 3 not reset yet, waiting 50ms
Dec 29 09:20:16 localhost ehci_hcd 0000:00:1d.7: port 3 full speed --> companion
Dec 29 09:20:16 localhost ehci_hcd 0000:00:1d.7: GetStatus port 3 status 003801 POWER OWNER sig=j  CONNECT
Dec 29 09:20:16 localhost uhci_hcd 0000:00:1d.1: wakeup_hc
Dec 29 09:20:16 localhost uhci_hcd 0000:00:1d.1: port 1 portsc 0083
Dec 29 09:20:16 localhost hub 2-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
Dec 29 09:20:16 localhost hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
Dec 29 09:20:16 localhost uhci_hcd 0000:00:1d.1: CTRL: TypeReq=0x2301 val=0x2 idx=0x0 len=0 ==> -32
Dec 29 09:20:16 localhost usb 2-1: new full speed USB device using address 5
Dec 29 09:20:16 localhost usb 2-1: new device strings: Mfr=1, Product=2, SerialNumber=0
Dec 29 09:20:16 localhost usb 2-1: default language 0x0409
Dec 29 09:20:16 localhost usb 2-1: Product: Palm Handheld
Dec 29 09:20:16 localhost usb 2-1: Manufacturer: Sony
Dec 29 09:20:16 localhost usb 2-1: hotplug
Dec 29 09:20:16 localhost usb 2-1: adding 2-1:1.0 (config #1, interface 0)
Dec 29 09:20:16 localhost usb 2-1:1.0: hotplug


I get that when I hit "HotSync".

I've been trying to use Evolution 2.0 and J-Pilot.

There is NO /dev/usb/tts (there is a /dev/usb/hid but it's empty) /dev/tts has 0-7 and there is a broken /dev/pilot file in there, it's supposed to point to /usb/tts/1. I've tried to tell j-pilot and evo that the palm is at /dev/tts/0 through 7 and tried to symlink /dev/pilot to /dev/tts/0-7 with no change.

I do not think I have udev and know little about that, however I ASSUME I shouldhave it, but can't seem to find out the paticulars of it.

Anyone have ideas/links to get this device running? I got a new watch for Christmas that doesn't store my appointmets (It's a Seiko SNA-139) so I'm trying to use this Sony Clie to fill my old watches shoes. (It was a Casio EDB-610)

Thanks ahead of time,
Justin :roll:

P.S. When I updated the kernel to 2.6.10-r1 my usb thumb drive and camera would not mount, and I could no longer save to my samba server. Made me say D@M#!
_________________
Be nice or you will be ctrl+alt+deleted .. if you are just being ugly, ctrl+alt+backspaced!
Back to top
View user's profile Send private message
NeddySeagoon
Administrator
Administrator


Joined: 05 Jul 2003
Posts: 43754
Location: 56N 3W

PostPosted: Wed Dec 29, 2004 3:11 pm    Post subject: Reply with quote

67comet,

Give up on genkernel.

In 2.6.10 the Options you want are
Code:
USB Serial Converter support (USB_SERIAL)
USB Handspring Visor / Palm m50x / Sony Clie Driver (USB_SERIAL_VISOR)

At least, it looks promising
_________________
Regards,

NeddySeagoon

Computer users fall into two groups:-
those that do backups
those that have never had a hard drive fail.
Back to top
View user's profile Send private message
67comet
Apprentice
Apprentice


Joined: 29 Oct 2004
Posts: 256
Location: Kadena AB, Okinawa Japan

PostPosted: Wed Dec 29, 2004 4:45 pm    Post subject: Reply with quote

K I tried make menuconfig ..

I see no where that there is an option for:
Code:

USB Serial Converter support (USB_SERIAL)
USB Handspring Visor / Palm m50x / Sony Clie Driver (USB_SERIAL_VISOR)


I looked at every step of:
Device Drivers>USB support>

I didn't see any other options for USB in the menu.

Also when I use genkernel --menuconfig all it gives me this same menu, with the same stuff checked off. (Might be the config file) ..

Sorry if I'm being so noob, but "grrrr" heheehe .. damn the kernel/modual gods!

Justin

DISREGARD .. FOUND IT! .. Sorry didn't dig deep enough .. Here is the route for those that might have the same issue finding it-----

Device Drivers>USB support>USB Serial Converter support>----
_________________
Be nice or you will be ctrl+alt+deleted .. if you are just being ugly, ctrl+alt+backspaced!
Back to top
View user's profile Send private message
67comet
Apprentice
Apprentice


Joined: 29 Oct 2004
Posts: 256
Location: Kadena AB, Okinawa Japan

PostPosted: Thu Dec 30, 2004 2:07 am    Post subject: Reply with quote

Never mind .. I redid my kernel, emerged udev, adjusted the conf files it needed, and rebooted ..

Did a little lusb and hit the hotsync button, and walla, there was my Sony Clie.

Fired up J-Pilot, hit hotsync on the Sony, then hotsync on J-Pilot .. Zip, nada, nothing.

What am I doing wrong?

After I emerged udev, I noticed that /dev/pilot and /dev/usb was gone. Let alone /dev/usb/tts/0 or other.

Suggestions anyone?

Justin 8O
_________________
Be nice or you will be ctrl+alt+deleted .. if you are just being ugly, ctrl+alt+backspaced!
Back to top
View user's profile Send private message
GungHo
Apprentice
Apprentice


Joined: 27 Aug 2004
Posts: 254

PostPosted: Mon Feb 14, 2005 8:51 pm    Post subject: Reply with quote

Hi,

have you solved this problem meanwhile ?

If not, have you had a look into /var/log/messages ?!

cheers
Back to top
View user's profile Send private message
furbmeister
n00b
n00b


Joined: 28 Apr 2005
Posts: 5

PostPosted: Thu Apr 28, 2005 9:19 am    Post subject: Reply with quote

If you're using udev this time around your usb devices for your palm should be setup as:

Code:
mknod /dev/ttyUSB0 c 188 0
mknod /dev/ttyUSB1 c 188 1


also make sure that /dev/ttyUSB0 and /dev/ttyUSB1 are r+w for your user.

then use /dev/ttyUSB1 to connect your clie to whatever syncing medium you use.
_________________
"If everything seems to be under control, you're not going fast enough"
Back to top
View user's profile Send private message
GungHo
Apprentice
Apprentice


Joined: 27 Aug 2004
Posts: 254

PostPosted: Mon May 02, 2005 8:09 pm    Post subject: Reply with quote

Hi furbmeister,

if I may say, you are wrong.

In the moment, when the sync button of the palm/visor/ie is pressed, and all necessary drivers are loaded, there are 2 device nodes automatically created, according to /etc/udev/rules.d/50-udev.rules

Code:
KERNEL="ttyUSB[0-9]*",  NAME="tts/USB%n", SYMLINK="%k"


You do not have to issue mknod commands, as it is the sense of the life of udev to create /dev entries automatically, so you do not have to intervene manually.

But if you have a image of your /dev directory which is automatically restored by udev on startup, then your mknod statements may make sense. But using such a file is against the sense of udev (but it is supported).

I'm not using such a file on my box, /dev is populated automatically, and there are some convenient links generated by a local rule file.

Maybe you should have a look at

http://www.gentoo.org/doc/en/usb-guide.xml
http://www.gentoo.org/doc/en/udev-guide.xml
http://www.gentoo.org/doc/en/migration-to-2.6.xml

HtH

cheers
Back to top
View user's profile Send private message
furbmeister
n00b
n00b


Joined: 28 Apr 2005
Posts: 5

PostPosted: Tue May 03, 2005 9:40 am    Post subject: Reply with quote

GungHo wrote:
Hi furbmeister,

if I may say, you are wrong.

In the moment, when the sync button of the palm/visor/ie is pressed, and all necessary drivers are loaded, there are 2 device nodes automatically created, according to /etc/udev/rules.d/50-udev.rules

Code:
KERNEL="ttyUSB[0-9]*",  NAME="tts/USB%n", SYMLINK="%k"


You do not have to issue mknod commands, as it is the sense of the life of udev to create /dev entries automatically, so you do not have to intervene manually.

But if you have a image of your /dev directory which is automatically restored by udev on startup, then your mknod statements may make sense. But using such a file is against the sense of udev (but it is supported).

I'm not using such a file on my box, /dev is populated automatically, and there are some convenient links generated by a local rule file.

Maybe you should have a look at

http://www.gentoo.org/doc/en/usb-guide.xml
http://www.gentoo.org/doc/en/udev-guide.xml
http://www.gentoo.org/doc/en/migration-to-2.6.xml

HtH

cheers



GungHo,

Yes, you're right about udev, I realized the same thing soon after I got more familiar with it ;-). My syncing however works perfect now. But this is what I did to get mine working after I realized that everytime I sync a new USB device is created, so then if I use /dev/ttyUSB1 the first time, it won't work the next, so I created 10-local.rules for udev and placed it in /etc/udev/rules.d/ and I placed the following inside the rules file:

Code:
SYSFS{product}="Palm Handheld", KERNEL="ttyUSB*", NAME="tts/USB%n", SYMLINK="pilot"


as you can see that will create a symlink for the second USB device everytime for /dev/pilot (please note this works for me because my clie always connects through the second USB device created, e.g. if USB0 and USB1 are created by udev, the Clie will use USB1 to sync). So this rule will create a symlink to USB0 first then since it's the same name (doesn't increment with the device number) it will stick with USB1 when it is created.
Now synching works for me every time, no matter what usb device is created, using /dev/pilot to sync of course.

By the way, from there you could also see that the USB devices are created in /dev/tts/USB*

Hope this helps someone that is having the same issues I had.

Drew.
_________________
"If everything seems to be under control, you're not going fast enough"
Back to top
View user's profile Send private message
GungHo
Apprentice
Apprentice


Joined: 27 Aug 2004
Posts: 254

PostPosted: Tue May 03, 2005 3:05 pm    Post subject: Reply with quote

Hi furbmeister,

Quote:
But this is what I did to get mine working after I realized that everytime I sync a new USB device is created, so then if I use /dev/ttyUSB1 the first time, it won't work the next, so I created 10-local.rules for udev and placed it in /etc/udev/rules.d/ and I placed the following inside the rules file:

Code:
SYSFS{product}="Palm Handheld", KERNEL="ttyUSB*", NAME="tts/USB%n", SYMLINK="pilot"


as you can see that will create a symlink for the second USB device everytime for /dev/pilot (please note this works for me because my clie always connects through the second USB device created, e.g. if USB0 and USB1 are created by udev, the Clie will use USB1 to sync). So this rule will create a symlink to USB0 first then since it's the same name (doesn't increment with the device number) it will stick with USB1 when it is created.


you did like I suggested in https://forums.gentoo.org/viewtopic-t-316924-highlight-.html :wink:

cheers
Back to top
View user's profile Send private message
jtaylor72
Apprentice
Apprentice


Joined: 01 Feb 2004
Posts: 197
Location: "the can", WA

PostPosted: Tue May 03, 2005 3:31 pm    Post subject: Reply with quote

Have you tried giving it flowers or chocolate?





sorry...with that title, I couldn't resist.
Back to top
View user's profile Send private message
furbmeister
n00b
n00b


Joined: 28 Apr 2005
Posts: 5

PostPosted: Wed May 04, 2005 1:05 am    Post subject: Reply with quote

GungHo wrote:
Hi furbmeister,

Quote:
But this is what I did to get mine working after I realized that everytime I sync a new USB device is created, so then if I use /dev/ttyUSB1 the first time, it won't work the next, so I created 10-local.rules for udev and placed it in /etc/udev/rules.d/ and I placed the following inside the rules file:

Code:
SYSFS{product}="Palm Handheld", KERNEL="ttyUSB*", NAME="tts/USB%n", SYMLINK="pilot"


as you can see that will create a symlink for the second USB device everytime for /dev/pilot (please note this works for me because my clie always connects through the second USB device created, e.g. if USB0 and USB1 are created by udev, the Clie will use USB1 to sync). So this rule will create a symlink to USB0 first then since it's the same name (doesn't increment with the device number) it will stick with USB1 when it is created.


you did like I suggested in https://forums.gentoo.org/viewtopic-t-316924-highlight-.html :wink:

cheers


Cool, udev is great isn't it? ;-)
_________________
"If everything seems to be under control, you're not going fast enough"
Back to top
View user's profile Send private message
GungHo
Apprentice
Apprentice


Joined: 27 Aug 2004
Posts: 254

PostPosted: Wed May 04, 2005 7:03 pm    Post subject: Reply with quote

yeah, full ack (cheers to Greg KH), as is the whole Gentoo :idea:
Back to top
View user's profile Send private message
Display posts from previous:   
Reply to topic    Gentoo Forums Forum Index Kernel & Hardware All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum