Gentoo Forums
Gentoo Forums
Gentoo Forums
Quick Search: in
X on sun ultra5
View unanswered posts
View posts from last 24 hours

 
Reply to topic    Gentoo Forums Forum Index Gentoo on Sparc
View previous topic :: View next topic  
Author Message
frankvandamme
n00b
n00b


Joined: 03 May 2004
Posts: 11
Location: Boortmeerbeek, Belgium

PostPosted: Fri Nov 19, 2004 3:44 pm    Post subject: X on sun ultra5 Reply with quote

Hello!

I have a Sun Ultra5 that has ben running Gentoo for a while now. The machine has a typical (old) fixed frequency Sun monitor (gdm-1962b). The framebuffer is based on the Ati mach64 chip. Before Gentoo I used another distribution under which I could use X by using the output of "fbset -x" as video modes (unfortunately I lost the XF86Config-4 file).

This is the output of fbset -x:

Code:

Section "Modes"
Identifier "Modes"
Mode "1152x900"
    # D: 93.870 MHz, H: 61.433 kHz, V: 65.564 Hz
    DotClock 93.871
    HTimings 1152 1210 1338 1528
    VTimings 900 902 906 937
    Flags    "+HSync" "-VSync" "Composite"    # Warning: XFree86 doesn't support accel
EndMode


This is my full xorg.conf file:
Code:

# **********************************************************************
# Module section -- this  section  is used to specify
# which dynamically loadable modules to load.
# **********************************************************************
#
Section "Module"

# This loads the DBE extension module.

    Load        "dbe"   # Double buffer extension

# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
    SubSection  "extmod"
      Option    "omit xfree86-dga"   # don't initialise the DGA extension
    EndSubSection

# This loads the Type1 and FreeType font modules
    Load        "type1"
    Load        "speedo"
#    Load        "freetype"
#    Load        "xtt"

# This loads the GLX module
#    Load       "glx"
# This loads the DRI module
#    Load       "dri"

EndSection

# **********************************************************************
# Files section.  This allows default font and rgb paths to be set
# **********************************************************************

Section "Files"

# The location of the RGB database.  Note, this is the name of the
# file minus the extension (like ".txt" or ".db").  There is normally
# no need to change the default.

    RgbPath "/usr/X11R6/lib/X11/rgb"

# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
#
# If you don't have a floating point coprocessor and emacs, Mosaic or other
# programs take long to start up, try moving the Type1 and Speedo directory
# to the end of this list (or comment them out).
#

    FontPath   "/usr/share/fonts/local/"
    FontPath   "/usr/share/fonts/misc/"
    FontPath   "/usr/share/fonts/75dpi/:unscaled"
    FontPath   "/usr/share/fonts/100dpi/:unscaled"
    FontPath   "/usr/share/fonts/Speedo/"
    FontPath   "/usr/share/fonts/Type1/"
#    FontPath   "/usr/share/fonts/TrueType/"
#    FontPath   "/usr/share/fonts/freefont/"
    FontPath   "/usr/share/fonts/75dpi/"
    FontPath   "/usr/share/fonts/100dpi/"

# The module search path.  The default path is shown here.

#    ModulePath "/usr/X11R6/lib/modules"

EndSection

# **********************************************************************
# Server flags section.
# **********************************************************************

Section "ServerFlags"

# Uncomment this to cause a core dump at the spot where a signal is
# received.  This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging

#    Option "NoTrapSignals"

# Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence
# (where n is 1 through 12).  This allows clients to receive these key
# events.

#    Option "DontVTSwitch"

# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
# This allows clients to receive this key event.

#    Option "DontZap"

# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
# sequences.  This allows clients to receive these key events.

#    Option "Dont Zoom"

# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.

#    Option "DisableVidModeExtension"

# Uncomment this to enable the use of a non-local xvidtune client.

#    Option "AllowNonLocalXvidtune"

# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings.

#    Option "DisableModInDev"

# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).

#    Option "AllowNonLocalModInDev"

EndSection

# **********************************************************************
# Input devices
# **********************************************************************

# **********************************************************************
# Core keyboard's InputDevice section
# **********************************************************************

Section "InputDevice"

    Identifier "Keyboard1"
    Driver "kbd"

# For most OSs the protocol can be omitted (it defaults to "Standard").
# When using XQUEUE (only for SVR3 and SVR4, but not Solaris),
# uncomment the following line.

#    Option     "Protocol"      "Xqueue"

    Option "AutoRepeat" "500 30"

# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
#    Option "Xleds"      "1 2 3"

#    Option "LeftAlt"     "Meta"
#    Option "RightAlt"    "ModeShift"

# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults).  For example, for a non-U.S.
# keyboard, you will probably want to use:
#    Option "XkbModel"    "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
#    Option "XkbModel"    "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
#    Option "XkbLayout"   "de"
# or:
#    Option "XkbLayout"   "de"
#    Option "XkbVariant"  "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
#    Option "XkbOptions"  "ctrl:swapcaps"

# These are the default XKB settings for XFree86
#    Option "XkbRules"    "xfree86"
#    Option "XkbModel"    "pc101"
#    Option "XkbLayout"   "us"
#    Option "XkbVariant"  ""
#    Option "XkbOptions"  ""

#    Option "XkbDisable"

    Option "XkbRules" "xfree86"
    Option "XkbModel" "pc101"
    Option "XkbLayout" "us"

EndSection


# **********************************************************************
# Core Pointer's InputDevice section
# **********************************************************************

Section "InputDevice"

# Identifier and driver

    Identifier "Mouse1"
    Driver "mouse"
    Option "Protocol"    "Auto"
    Option "Device"      "/dev/sunmouse"

# Mouse-speed setting for PS/2 mouse.

#    Option "Resolution" "256"

# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.

#    Option "Protocol" "Xqueue"

# Baudrate and SampleRate are only for some Logitech mice. In
# almost every case these lines should be omitted.

#    Option "BaudRate" "9600"
#    Option "SampleRate" "150"

# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)

#    Option "Emulate3Buttons"
#    Option "Emulate3Timeout"    "50"

# ChordMiddle is an option for some 3-button Logitech mice

#    Option "ChordMiddle"

EndSection


# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section "Monitor"

    Identifier  "gdm-1962b"

UseModes "Modes"
EndSection

Section "Modes"
Identifier "Modes"
Mode "1152x900"
    # D: 93.870 MHz, H: 61.433 kHz, V: 65.564 Hz
    DotClock 93.871
    HTimings 1152 1210 1338 1528
    VTimings 900 902 906 937
    Flags    "+HSync" "-VSync" "Composite"    # Warning: XFree86 doesn't support accel
EndMode
EndSection
# **********************************************************************
# Graphics device section
# **********************************************************************

# Device configured by xf86config:

Section "Device"
    Identifier  "mach64"
    Driver      "ati"
 # unsupported card
    #VideoRam    1024
    # Insert Clocks lines here if appropriate
EndSection


# **********************************************************************
# Screen sections
# **********************************************************************

# Any number of screen sections may be present.  Each describes
# the configuration of a single screen.  A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
    Identifier  "Screen 1"
    Device      "mach64"
    Monitor     "gdm-1962b"
    DefaultDepth 8

    Subsection "Display"
        Depth       8
        Modes       "1152x900"
        ViewPort    0 0
    EndSubsection
EndSection

# **********************************************************************
# ServerLayout sections.
# **********************************************************************

# Any number of ServerLayout sections may be present.  Each describes
# the way multiple screens are organised.  A specific ServerLayout
# section may be specified from the X server command line with the
# "-layout" option.  In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.

Section "ServerLayout"

# The Identifier line must be present
    Identifier  "Simple Layout"

    Screen "Screen 1"

# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used.  Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".

    InputDevice "Mouse1" "CorePointer"
    InputDevice "Keyboard1" "CoreKeyboard"

EndSection

# Section "DRI"
#    Mode 0666
# EndSection


And this is Xorg's log file:

Code:


X Window System Version 6.8.0
Release Date: 8 September 2004
X Protocol Version 11, Revision 0, Release 6.8
Build Operating System: Linux 2.4.26-sparc sparc64 [ELF]
Current Operating System: Linux hades 2.4.26-sparc #3 Tue Oct 19 16:15:41 CEST 2004 sparc64
Build Date: 22 October 2004
 Before reporting problems, check http://wiki.X.Org
 to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
 (++) from command line, (!!) notice, (II) informational,
 (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Fri Nov 19 11:38:13 2004
(==) Using config file: "/etc/X11/xorg.conf"
(==) ServerLayout "Simple Layout"
(**) |-->Screen "Screen 1" (0)
(**) |   |-->Monitor "gdm-1962b"
(**) |   |-->Device "mach64"
(**) |-->Input Device "Mouse1"
(**) |-->Input Device "Keyboard1"
(WW) The directory "/usr/share/fonts/Speedo/" does not exist.
 Entry deleted from font path.
(**) FontPath set to "/usr/share/fonts/local/,/usr/share/fonts/misc/,/usr/share/fonts/75dpi/:unscaled, /usr/share/fonts/100dpi/:unscaled,/usr/share/fonts/Type1/,/usr/share/fonts/75dpi/,/usr/share/fonts/100dpi/"
(**) RgbPath set to "/usr/X11R6/lib/X11/rgb"
(==) ModulePath set to "/usr/X11R6/lib/modules"
(WW) Open APM failed (/dev/apm_bios) (No such file or directory)
(II) Module ABI versions:
 X.Org ANSI C Emulation: 0.2
 X.Org Video Driver: 0.7
 X.Org XInput driver : 0.4
 X.Org Server Extension : 0.2
 X.Org Font Renderer : 0.4
(II) Loader running on linux
(II) LoadModule: "bitmap"
(II) Loading /usr/X11R6/lib/modules/fonts/libbitmap.a
(II) Module bitmap: vendor="X.Org Foundation"
 compiled for 6.8.0, module version = 1.0.0
 Module class: X.Org Font Renderer
 ABI class: X.Org Font Renderer, version 0.4
(II) Loading font Bitmap
(II) LoadModule: "pcidata"
(II) Loading /usr/X11R6/lib/modules/libpcidata.a
(II) Module pcidata: vendor="X.Org Foundation"
 compiled for 6.8.0, module version = 1.0.0
 ABI class: X.Org Video Driver, version 0.7
Using vt 7
(--) using VT number 7

(II) PCI: PCI scan (all values are in hex)
(II) PCI: 00:00:0: chip 108e,a000 card 0000,0000 rev 00 class 06,00,00 hdr 00
(II) PCI: 00:01:0: chip 108e,5000 card 0000,0000 rev 11 class 06,04,00 hdr 81
(II) PCI: 00:01:1: chip 108e,5000 card 0000,0000 rev 11 class 06,04,00 hdr 81
(II) PCI: 01:01:0: chip 108e,1000 card 0000,0000 rev 01 class 06,80,00 hdr 80
(II) PCI: 01:01:1: chip 108e,1001 card 0000,0000 rev 01 class 02,00,00 hdr 80
(II) PCI: 01:02:0: chip 1002,4754 card 0000,0000 rev 9a class 03,00,00 hdr 00
(II) PCI: 01:03:0: chip 1095,0646 card 1095,0646 rev 03 class 01,01,8f hdr 00
(II) PCI: 02:01:0: chip 10ec,8029 card 10ec,8029 rev 00 class 02,00,00 hdr 00
(II) PCI: End of PCI scan
(II) Host-to-PCI bridge:
(II) Bus 0: bridge is at (0:0:0), (0,0,2), BCTRL: 0x0008 (VGA_EN is set)
(II) Bus 0 I/O range:
   [0] -1   1   0x00000000 - 0x00ffffff (0x1000000) IX[B]
(II) Bus 0 non-prefetchable memory range:
   [0] -1   1   0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus 0 prefetchable memory range:
   [0] -1   1   0x00000000 - 0xffffffff (0x0) MX[B]
(II) PCI-to-PCI bridge:
(II) Bus 2: bridge is at (0:1:0), (0,2,255), BCTRL: 0x002b (VGA_EN is set)
(II) Bus 2 I/O range:
   [0] -1   1   0x00000000 - 0x001fffff (0x200000) IX[B]
   [1] -1   1   0x00200000 - 0x003fffff (0x200000) IX[B]
   [2] -1   1   0x00400000 - 0x005fffff (0x200000) IX[B]
   [3] -1   1   0x00600000 - 0x007fffff (0x200000) IX[B]
   [4] -1   1   0x00800000 - 0x009fffff (0x200000) IX[B]
   [5] -1   1   0x00a00000 - 0x00bfffff (0x200000) IX[B]
(II) Bus 2 non-prefetchable memory range:
   [0] -1   1   0x00000000 - 0x1fffffff (0x20000000) MX[B]
   [1] -1   1   0x20000000 - 0x3fffffff (0x20000000) MX[B]
   [2] -1   1   0x40000000 - 0x5fffffff (0x20000000) MX[B]
   [3] -1   1   0x60000000 - 0x7fffffff (0x20000000) MX[B]
   [4] -1   1   0x80000000 - 0x9fffffff (0x20000000) MX[B]
   [5] -1   1   0xa0000000 - 0xbfffffff (0x20000000) MX[B]
(II) PCI-to-PCI bridge:
(II) Bus 1: bridge is at (0:1:1), (0,1,1), BCTRL: 0x0023 (VGA_EN is cleared)
(II) Bus 1 I/O range:
   [0] -1   1   0x00c00000 - 0x00dfffff (0x200000) IX[B]
   [1] -1   1   0x00e00000 - 0x00ffffff (0x200000) IX[B]
(II) Bus 1 non-prefetchable memory range:
   [0] -1   1   0xe0000000 - 0xffffffff (0x20000000) MX[B]
(--) PCI:*(1:2:0) ATI Technologies Inc 3D Rage I/II 215GT [Mach64 GT] rev 154, Mem @ 0xe1000000/24, 0xe0008000/12, I/O @ 0xc00400/8, BIOS @ 0xe0020000/17
(II) Addressable bus resource ranges are
   [0] -1   1   0x00000000 - 0xffffffff (0x0) MX[B]
   [1] -1   1   0x00000000 - 0x00ffffff (0x1000000) IX[B]
(II) OS-reported resource ranges:
   [0] -1   1   0xffffffff - 0xffffffff (0x1) MX[B]
   [1] -1   1   0x000f0000 - 0x000fffff (0x10000) MX[B]
   [2] -1   1   0x000c0000 - 0x000effff (0x30000) MX[B]
   [3] -1   1   0x00000000 - 0x0009ffff (0xa0000) MX[B]
   [4] -1   1   0x00ffffff - 0x00ffffff (0x1) IX[B]
   [5] -1   1   0x00000000 - 0x00000000 (0x1) IX[B]
(II) Active PCI resource ranges:
   [0] -1   1   0xe0000000 - 0xe0007fff (0x8000) MX[B]
   [1] -1   1   0xf1000000 - 0xf17fffff (0x800000) MX[B]
   [2] -1   1   0xf0000000 - 0xf0ffffff (0x1000000) MX[B]
   [3] -1   1   0xe0020000 - 0xe003ffff (0x20000) MX[B](B)
   [4] -1   1   0xe0008000 - 0xe0008fff (0x1000) MX[B](B)
   [5] -1   1   0xe1000000 - 0xe1ffffff (0x1000000) MX[B](B)
   [6] -1   1   0x00000400 - 0x0000041f (0x20) IX[B]
   [7] -1   1   0x00c00020 - 0x00c0002f (0x10) IX[B]
   [8] -1   1   0x00c00018 - 0x00c0001b (0x4) IX[B]
   [9] -1   1   0x00c00010 - 0x00c00017 (0x8) IX[B]
   [10] -1   1   0x00c00008 - 0x00c0000b (0x4) IX[B]
   [11] -1   1   0x00c00000 - 0x00c00007 (0x8) IX[B]
   [12] -1   1   0x00c00400 - 0x00c004ff (0x100) IX[B](B)
(II) Active PCI resource ranges after removing overlaps:
   [0] -1   1   0xe0000000 - 0xe0007fff (0x8000) MX[B]
   [1] -1   1   0xf1000000 - 0xf17fffff (0x800000) MX[B]
   [2] -1   1   0xf0000000 - 0xf0ffffff (0x1000000) MX[B]
   [3] -1   1   0xe0020000 - 0xe003ffff (0x20000) MX[B](B)
   [4] -1   1   0xe0008000 - 0xe0008fff (0x1000) MX[B](B)
   [5] -1   1   0xe1000000 - 0xe1ffffff (0x1000000) MX[B](B)
   [6] -1   1   0x00000400 - 0x0000041f (0x20) IX[B]
   [7] -1   1   0x00c00020 - 0x00c0002f (0x10) IX[B]
   [8] -1   1   0x00c00018 - 0x00c0001b (0x4) IX[B]
   [9] -1   1   0x00c00010 - 0x00c00017 (0x8) IX[B]
   [10] -1   1   0x00c00008 - 0x00c0000b (0x4) IX[B]
   [11] -1   1   0x00c00000 - 0x00c00007 (0x8) IX[B]
   [12] -1   1   0x00c00400 - 0x00c004ff (0x100) IX[B](B)
(II) OS-reported resource ranges after removing overlaps with PCI:
   [0] -1   1   0xffffffff - 0xffffffff (0x1) MX[B]
   [1] -1   1   0x000f0000 - 0x000fffff (0x10000) MX[B]
   [2] -1   1   0x000c0000 - 0x000effff (0x30000) MX[B]
   [3] -1   1   0x00000000 - 0x0009ffff (0xa0000) MX[B]
   [4] -1   1   0x00ffffff - 0x00ffffff (0x1) IX[B]
   [5] -1   1   0x00000000 - 0x00000000 (0x1) IX[B]
(II) All system resource ranges:
   [0] -1   1   0xffffffff - 0xffffffff (0x1) MX[B]
   [1] -1   1   0x000f0000 - 0x000fffff (0x10000) MX[B]
   [2] -1   1   0x000c0000 - 0x000effff (0x30000) MX[B]
   [3] -1   1   0x00000000 - 0x0009ffff (0xa0000) MX[B]
   [4] -1   1   0xe0000000 - 0xe0007fff (0x8000) MX[B]
   [5] -1   1   0xf1000000 - 0xf17fffff (0x800000) MX[B]
   [6] -1   1   0xf0000000 - 0xf0ffffff (0x1000000) MX[B]
   [7] -1   1   0xe0020000 - 0xe003ffff (0x20000) MX[B](B)
   [8] -1   1   0xe0008000 - 0xe0008fff (0x1000) MX[B](B)
   [9] -1   1   0xe1000000 - 0xe1ffffff (0x1000000) MX[B](B)
   [10] -1   1   0x00ffffff - 0x00ffffff (0x1) IX[B]
   [11] -1   1   0x00000000 - 0x00000000 (0x1) IX[B]
   [12] -1   1   0x00000400 - 0x0000041f (0x20) IX[B]
   [13] -1   1   0x00c00020 - 0x00c0002f (0x10) IX[B]
   [14] -1   1   0x00c00018 - 0x00c0001b (0x4) IX[B]
   [15] -1   1   0x00c00010 - 0x00c00017 (0x8) IX[B]
   [16] -1   1   0x00c00008 - 0x00c0000b (0x4) IX[B]
   [17] -1   1   0x00c00000 - 0x00c00007 (0x8) IX[B]
   [18] -1   1   0x00c00400 - 0x00c004ff (0x100) IX[B](B)
(II) LoadModule: "dbe"
(II) Loading /usr/X11R6/lib/modules/extensions/libdbe.a
(II) Module dbe: vendor="X.Org Foundation"
   compiled for 6.8.0, module version = 1.0.0
   Module class: X.Org Server Extension
   ABI class: X.Org Server Extension, version 0.2
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "extmod"
(II) Loading /usr/X11R6/lib/modules/extensions/libextmod.a
(II) Module extmod: vendor="X.Org Foundation"
   compiled for 6.8.0, module version = 1.0.0
   Module class: X.Org Server Extension
   ABI class: X.Org Server Extension, version 0.2
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension DPMS
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "type1"
(II) Loading /usr/X11R6/lib/modules/fonts/libtype1.a
(II) Module type1: vendor="X.Org Foundation"
   compiled for 6.8.0, module version = 1.0.2
   Module class: X.Org Font Renderer
   ABI class: X.Org Font Renderer, version 0.4
(II) Loading font Type1
(II) Loading font CID
(II) LoadModule: "speedo"
(WW) Warning, couldn't open module speedo
(II) UnloadModule: "speedo"
(EE) Failed to load module "speedo" (module does not exist, 0)
(II) LoadModule: "ati"
(II) Loading /usr/X11R6/lib/modules/drivers/ati_drv.o
(II) Module ati: vendor="X.Org Foundation"
   compiled for 6.8.0, module version = 6.5.6
   Module class: X.Org Video Driver
   ABI class: X.Org Video Driver, version 0.7
(II) LoadModule: "mouse"
(II) Loading /usr/X11R6/lib/modules/input/mouse_drv.o
(II) Module mouse: vendor="X.Org Foundation"
   compiled for 6.8.0, module version = 1.0.0
   Module class: X.Org XInput Driver
   ABI class: X.Org XInput driver, version 0.4
(II) LoadModule: "kbd"
(II) Loading /usr/X11R6/lib/modules/input/kbd_drv.o
(II) Module kbd: vendor="X.Org Foundation"
   compiled for 6.8.0, module version = 1.0.0
   Module class: X.Org XInput Driver
   ABI class: X.Org XInput driver, version 0.4
(II) ATI: ATI driver (version 6.5.6) for chipset: ati
(II) R128: Driver for ATI Rage 128 chipsets:
   ATI Rage 128 Mobility M3 LE (PCI), ATI Rage 128 Mobility M3 LF (AGP),
   ATI Rage 128 Mobility M4 MF (AGP), ATI Rage 128 Mobility M4 ML (AGP),
   ATI Rage 128 Pro GL PA (PCI/AGP), ATI Rage 128 Pro GL PB (PCI/AGP),
   ATI Rage 128 Pro GL PC (PCI/AGP), ATI Rage 128 Pro GL PD (PCI),
   ATI Rage 128 Pro GL PE (PCI/AGP), ATI Rage 128 Pro GL PF (AGP),
   ATI Rage 128 Pro VR PG (PCI/AGP), ATI Rage 128 Pro VR PH (PCI/AGP),
   ATI Rage 128 Pro VR PI (PCI/AGP), ATI Rage 128 Pro VR PJ (PCI/AGP),
   ATI Rage 128 Pro VR PK (PCI/AGP), ATI Rage 128 Pro VR PL (PCI/AGP),
   ATI Rage 128 Pro VR PM (PCI/AGP), ATI Rage 128 Pro VR PN (PCI/AGP),
   ATI Rage 128 Pro VR PO (PCI/AGP), ATI Rage 128 Pro VR PP (PCI),
   ATI Rage 128 Pro VR PQ (PCI/AGP), ATI Rage 128 Pro VR PR (PCI),
   ATI Rage 128 Pro VR PS (AGP?), ATI Rage 128 Pro VR PT (AGP?),
   ATI Rage 128 Pro VR PU (AGP?), ATI Rage 128 Pro VR PV (AGP?),
   ATI Rage 128 Pro VR PW (AGP?), ATI Rage 128 Pro VR PX (AGP?),
   ATI Rage 128 GL RE (PCI), ATI Rage 128 GL RF (AGP),
   ATI Rage 128 RG (AGP), ATI Rage 128 VR RK (PCI),
   ATI Rage 128 VR RL (AGP), ATI Rage 128 4X SE (AGP?),
   ATI Rage 128 4X SF (AGP?), ATI Rage 128 4X SG (AGP?),
   ATI Rage 128 4X SH (AGP?), ATI Rage 128 4X SK (AGP?),
   ATI Rage 128 4X SL (AGP?), ATI Rage 128 4X SM (AGP),
   ATI Rage 128 4X SN (AGP?), ATI Rage 128 Pro ULTRA TF (AGP),
   ATI Rage 128 Pro ULTRA TL (AGP), ATI Rage 128 Pro ULTRA TR (AGP),
   ATI Rage 128 Pro ULTRA TS (AGP?), ATI Rage 128 Pro ULTRA TT (AGP?),
   ATI Rage 128 Pro ULTRA TU (AGP?)
(II) RADEON: Driver for ATI Radeon chipsets: ATI Radeon QD (AGP),
   ATI Radeon QE (AGP), ATI Radeon QF (AGP), ATI Radeon QG (AGP),
   ATI Radeon VE/7000 QY (AGP/PCI), ATI Radeon VE/7000 QZ (AGP/PCI),
   ATI Radeon Mobility M7 LW (AGP),
   ATI Mobility FireGL 7800 M7 LX (AGP),
   ATI Radeon Mobility M6 LY (AGP), ATI Radeon Mobility M6 LZ (AGP),
   ATI Radeon IGP320 (A3) 4136, ATI Radeon IGP320M (U1) 4336,
   ATI Radeon IGP330/340/350 (A4) 4137,
   ATI Radeon IGP330M/340M/350M (U2) 4337,
   ATI Radeon 7000 IGP (A4+) 4237, ATI Radeon Mobility 7000 IGP 4437,
   ATI FireGL 8700/8800 QH (AGP), ATI Radeon 8500 QL (AGP),
   ATI Radeon 9100 QM (AGP), ATI Radeon 8500 AIW BB (AGP),
   ATI Radeon 8500 AIW BC (AGP), ATI Radeon 7500 QW (AGP/PCI),
   ATI Radeon 7500 QX (AGP/PCI), ATI Radeon 9000/PRO If (AGP/PCI),
   ATI Radeon 9000 Ig (AGP/PCI), ATI FireGL Mobility 9000 (M9) Ld (AGP),
   ATI Radeon Mobility 9000 (M9) Lf (AGP),
   ATI Radeon Mobility 9000 (M9) Lg (AGP),
   ATI Radeon 9100 IGP (A5) 5834,
   ATI Radeon Mobility 9100 IGP (U3) 5835, ATI Radeon 9100 PRO IGP 7834,
   ATI Radeon Mobility 9200 IGP 7835, ATI Radeon 9200PRO 5960 (AGP),
   ATI Radeon 9200 5961 (AGP), ATI Radeon 9200 5962 (AGP),
   ATI Radeon 9200SE 5964 (AGP),
   ATI Radeon Mobility 9200 (M9+) 5C61 (AGP),
   ATI Radeon Mobility 9200 (M9+) 5C63 (AGP), ATI Radeon 9500 AD (AGP),
   ATI Radeon 9500 AE (AGP), ATI Radeon 9600TX AF (AGP),
   ATI FireGL Z1 AG (AGP), ATI Radeon 9700 Pro ND (AGP),
   ATI Radeon 9700/9500Pro NE (AGP), ATI Radeon 9700 NF (AGP),
   ATI FireGL X1 NG (AGP), ATI Radeon 9600 AP (AGP),
   ATI Radeon 9600SE AQ (AGP), ATI Radeon 9600XT AR (AGP),
   ATI Radeon 9600 AS (AGP), ATI FireGL T2 AT (AGP),
   ATI FireGL RV360 AV (AGP),
   ATI Radeon Mobility 9600/9700 (M10/M11) NP (AGP),
   ATI Radeon Mobility 9600 (M10) NQ (AGP),
   ATI Radeon Mobility 9600 (M11) NR (AGP),
   ATI Radeon Mobility 9600 (M10) NS (AGP),
   ATI FireGL Mobility T2 (M10) NT (AGP),
   ATI FireGL Mobility T2e (M11) NV (AGP), ATI Radeon 9800SE AH (AGP),
   ATI Radeon 9800 AI (AGP), ATI Radeon 9800 AJ (AGP),
   ATI FireGL X2 AK (AGP), ATI Radeon 9800PRO NH (AGP),
   ATI Radeon 9800 NI (AGP), ATI FireGL X2 NK (AGP),
   ATI Radeon 9800XT NJ (AGP), ATI Radeon X600 (RV380) 3E50 (PCIE),
   ATI FireGL V3200 (RV380) 3E54 (PCIE),
   ATI Radeon Mobility X600 (M24) 3150 (PCIE),
   ATI FireGL M24 GL 3154 (PCIE), ATI Radeon X300 (RV370) 5B60 (PCIE),
   ATI Radeon X600 (RV370) 5B62 (PCIE),
   ATI FireGL V3100 (RV370) 5B64 (PCIE),
   ATI FireGL D1100 (RV370) 5B65 (PCIE),
   ATI Radeon Mobility M300 (M22) 5460 (PCIE),
   ATI FireGL M22 GL 5464 (PCIE), ATI Radeon X800 (R420) JH (AGP),
   ATI Radeon X800PRO (R420) JI (AGP),
   ATI Radeon X800SE (R420) JJ (AGP), ATI Radeon X800 (R420) JK (AGP),
   ATI Radeon X800 (R420) JL (AGP), ATI FireGL X3 (R420) JM (AGP),
   ATI Radeon Mobility 9800 (M18) JN (AGP),
   ATI Radeon X800XT (R420) JP (AGP), ATI Radeon X800 (R423) UH (PCIE),
   ATI Radeon X800PRO (R423) UI (PCIE),
   ATI Radeon X800LE (R423) UJ (PCIE),
   ATI Radeon X800SE (R423) UK (PCIE),
   ATI FireGL V7200 (R423) UQ (PCIE), ATI FireGL V5100 (R423) UR (PCIE),
   ATI FireGL V7100 (R423) UT (PCIE),
   ATI Radeon X800XT (R423) 5D57 (PCIE)
(WW) Attempt to disable VGA routing through Simba at 0:1:0 disallowed.
(II) Primary Device is: PCI 01:02:0
(II) ATI:  Candidate "Device" section "mach64".
(WW) Attempt to enable VGA routing through Simba at 0:1:1 disallowed.
(II) ATI:  Shared PCI/AGP Mach64 in slot 1:2:0 detected.
(II) ATI:  Shared PCI/AGP Mach64 in slot 1:2:0 assigned to active "Device" section "mach64".
(II) Loading sub module "atimisc"
(II) LoadModule: "atimisc"
(II) Loading /usr/X11R6/lib/modules/drivers/atimisc_drv.o
(II) Module atimisc: vendor="X.Org Foundation"
   compiled for 6.8.0, module version = 6.5.6
   Module class: X.Org Video Driver
   ABI class: X.Org Video Driver, version 0.7
(II) resource ranges after probing:
   [0] -1   1   0xffffffff - 0xffffffff (0x1) MX[B]
   [1] -1   1   0x000f0000 - 0x000fffff (0x10000) MX[B]
   [2] -1   1   0x000c0000 - 0x000effff (0x30000) MX[B]
   [3] -1   1   0x00000000 - 0x0009ffff (0xa0000) MX[B]
   [4] -1   1   0xe0000000 - 0xe0007fff (0x8000) MX[B]
   [5] -1   1   0xf1000000 - 0xf17fffff (0x800000) MX[B]
   [6] -1   1   0xf0000000 - 0xf0ffffff (0x1000000) MX[B]
   [7] -1   1   0xe0020000 - 0xe003ffff (0x20000) MX[B](B)
   [8] -1   1   0xe0008000 - 0xe0008fff (0x1000) MX[B](B)
   [9] -1   1   0xe1000000 - 0xe1ffffff (0x1000000) MX[B](B)
   [10] -1   1   0x00ffffff - 0x00ffffff (0x1) IX[B]
   [11] -1   1   0x00000000 - 0x00000000 (0x1) IX[B]
   [12] -1   1   0x00000400 - 0x0000041f (0x20) IX[B]
   [13] -1   1   0x00c00020 - 0x00c0002f (0x10) IX[B]
   [14] -1   1   0x00c00018 - 0x00c0001b (0x4) IX[B]
   [15] -1   1   0x00c00010 - 0x00c00017 (0x8) IX[B]
   [16] -1   1   0x00c00008 - 0x00c0000b (0x4) IX[B]
   [17] -1   1   0x00c00000 - 0x00c00007 (0x8) IX[B]
   [18] -1   1   0x00c00400 - 0x00c004ff (0x100) IX[B](B)
(==) ATI(0): Chipset:  "ati".
(**) ATI(0): Depth 8, (--) framebuffer bpp 8
(II) ATI(0): BIOS Data:  BIOSSize=0x0000, ROMTable=0x0000.
(II) ATI(0): BIOS Data:  ClockTable=0x0000, FrequencyTable=0x0000.
(II) ATI(0): BIOS Data:  LCDTable=0x0000, LCDPanelInfo=0x0000.
(II) ATI(0): BIOS Data:  VideoTable=0x0000, HardwareTable=0x0000.
(II) ATI(0): BIOS Data:  I2CType=0x00, Tuner=0x00, Decoder=0x00, Audio=0x0F.
(--) ATI(0): ATI 3D Rage II graphics controller detected.
(--) ATI(0): Chip type 4754 "GT", version 2, foundry UMC, class 0, revision 0x02.
(--) ATI(0): PCI bus interface detected.
(--) ATI(0): ATI Mach64 adapter detected.
(!!) ATI(0): For information on using the multimedia capabilities
   of this adapter, please see http://gatos.sf.net.
(--) ATI(0): Internal RAMDAC (subtype 1) detected.
(==) ATI(0): RGB weight 888
(==) ATI(0): Default visual is PseudoColor
(==) ATI(0): Using gamma correction (1.0, 1.0, 1.0)
(II) ATI(0): Using Mach64 accelerator CRTC.
(II) ATI(0): Storing hardware cursor image at 0xE11FFC00.
(II) ATI(0): Using 8 MB linear aperture at 0xE1800000.
(!!) ATI(0): Virtual resolutions will be limited to 2047 kB
 due to linear aperture size and/or placement of hardware cursor image area.
(II) ATI(0): Using Block 0 MMIO aperture at 0xE0008400.
(II) ATI(0): Using Block 1 MMIO aperture at 0xE0008000.
(II) ATI(0): MMIO write caching enabled.
(--) ATI(0): 2048 kB of SGRAM (1:1) detected (using 2047 kB).
(WW) ATI(0): Cannot shadow an accelerated frame buffer.
(II) ATI(0): Engine XCLK 66.818 MHz;  Refresh rate code 4.
(--) ATI(0): Internal programmable clock generator detected.
(--) ATI(0): Reference clock 157.5/11 (14.318) MHz.
(II) ATI(0): gdm-1962b: Using default hsync range of 28.00-33.00 kHz
(II) ATI(0): gdm-1962b: Using default vrefresh range of 43.00-72.00 Hz
(II) ATI(0): Maximum clock: 170.00 MHz
(II) ATI(0): Not using mode "1152x900" (hsync out of range)
(II) ATI(0): Not using default mode "640x350" (hsync out of range)
(II) ATI(0): Not using default mode "320x175" (hsync out of range)
(II) ATI(0): Not using default mode "640x400" (hsync out of range)
(II) ATI(0): Not using default mode "320x200" (hsync out of range)
(II) ATI(0): Not using default mode "720x400" (hsync out of range)
(II) ATI(0): Not using default mode "360x200" (hsync out of range)
(II) ATI(0): Not using default mode "640x480" (hsync out of range)
(II) ATI(0): Not using default mode "320x240" (hsync out of range)
(II) ATI(0): Not using default mode "640x480" (hsync out of range)
(II) ATI(0): Not using default mode "320x240" (hsync out of range)
(II) ATI(0): Not using default mode "640x480" (hsync out of range)
(II) ATI(0): Not using default mode "320x240" (hsync out of range)
(II) ATI(0): Not using default mode "800x600" (hsync out of range)
(II) ATI(0): Not using default mode "400x300" (hsync out of range)
(II) ATI(0): Not using default mode "800x600" (hsync out of range)
(II) ATI(0): Not using default mode "400x300" (hsync out of range)
(II) ATI(0): Not using default mode "800x600" (hsync out of range)
(II) ATI(0): Not using default mode "400x300" (hsync out of range)
(II) ATI(0): Not using default mode "800x600" (hsync out of range)
(II) ATI(0): Not using default mode "400x300" (hsync out of range)
(II) ATI(0): Not using default mode "800x600" (hsync out of range)
(II) ATI(0): Not using default mode "400x300" (hsync out of range)
(II) ATI(0): Not using default mode "1024x768" (hsync out of range)
(II) ATI(0): Not using default mode "512x384" (hsync out of range)
(II) ATI(0): Not using default mode "1024x768" (hsync out of range)
(II) ATI(0): Not using default mode "512x384" (hsync out of range)
(II) ATI(0): Not using default mode "1024x768" (hsync out of range)
(II) ATI(0): Not using default mode "512x384" (hsync out of range)
(II) ATI(0): Not using default mode "1024x768" (hsync out of range)
(II) ATI(0): Not using default mode "512x384" (hsync out of range)
(II) ATI(0): Not using default mode "1024x768" (hsync out of range)
(II) ATI(0): Not using default mode "512x384" (hsync out of range)
(II) ATI(0): Not using default mode "1152x864" (hsync out of range)
(II) ATI(0): Not using default mode "576x432" (hsync out of range)
(II) ATI(0): Not using default mode "1280x960" (hsync out of range)
(II) ATI(0): Not using default mode "640x480" (hsync out of range)
(II) ATI(0): Not using default mode "1280x960" (hsync out of range)
(II) ATI(0): Not using default mode "640x480" (hsync out of range)
(II) ATI(0): Not using default mode "1280x1024" (hsync out of range)
(II) ATI(0): Not using default mode "640x512" (hsync out of range)
(II) ATI(0): Not using default mode "1280x1024" (hsync out of range)
(II) ATI(0): Not using default mode "640x512" (hsync out of range)
(II) ATI(0): Not using default mode "1280x1024" (hsync out of range)
(II) ATI(0): Not using default mode "640x512" (hsync out of range)
(II) ATI(0): Not using default mode "1600x1200" (hsync out of range)
(II) ATI(0): Not using default mode "800x600" (hsync out of range)
(II) ATI(0): Not using default mode "1600x1200" (bad mode clock/interlace/doublescan)
(II) ATI(0): Not using default mode "800x600" (hsync out of range)
(II) ATI(0): Not using default mode "1600x1200" (bad mode clock/interlace/doublescan)
(II) ATI(0): Not using default mode "800x600" (hsync out of range)
(II) ATI(0): Not using default mode "1600x1200" (bad mode clock/interlace/doublescan)
(II) ATI(0): Not using default mode "800x600" (hsync out of range)
(II) ATI(0): Not using default mode "1600x1200" (bad mode clock/interlace/doublescan)
(II) ATI(0): Not using default mode "800x600" (hsync out of range)
(II) ATI(0): Not using default mode "1792x1344" (insufficient memory for mode)
(II) ATI(0): Not using default mode "896x672" (hsync out of range)
(II) ATI(0): Not using default mode "1792x1344" (insufficient memory for mode)
(II) ATI(0): Not using default mode "896x672" (hsync out of range)
(II) ATI(0): Not using default mode "1856x1392" (insufficient memory for mode)
(II) ATI(0): Not using default mode "928x696" (hsync out of range)
(II) ATI(0): Not using default mode "1856x1392" (insufficient memory for mode)
(II) ATI(0): Not using default mode "928x696" (hsync out of range)
(II) ATI(0): Not using default mode "1920x1440" (insufficient memory for mode)
(II) ATI(0): Not using default mode "960x720" (hsync out of range)
(II) ATI(0): Not using default mode "1920x1440" (insufficient memory for mode)
(II) ATI(0): Not using default mode "960x720" (hsync out of range)
(II) ATI(0): Not using default mode "832x624" (hsync out of range)
(II) ATI(0): Not using default mode "416x312" (hsync out of range)
(II) ATI(0): Not using default mode "1152x768" (hsync out of range)
(II) ATI(0): Not using default mode "576x384" (hsync out of range)
(II) ATI(0): Not using default mode "1400x1050" (hsync out of range)
(II) ATI(0): Not using default mode "700x525" (hsync out of range)
(II) ATI(0): Not using default mode "1400x1050" (hsync out of range)
(II) ATI(0): Not using default mode "700x525" (hsync out of range)
(II) ATI(0): Not using default mode "1600x1024" (hsync out of range)
(II) ATI(0): Not using default mode "800x512" (hsync out of range)
(II) ATI(0): Not using default mode "1920x1440" (insufficient memory for mode)
(II) ATI(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan)
(II) ATI(0): Not using default mode "2048x1536" (insufficient memory for mode)
(II) ATI(0): Not using default mode "1024x768" (hsync out of range)
(II) ATI(0): Not using default mode "2048x1536" (insufficient memory for mode)
(II) ATI(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan)
(II) ATI(0): Not using default mode "2048x1536" (insufficient memory for mode)
(II) ATI(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan)
(II) ATI(0): Not using mode "1152x900" (no mode of this name)
(--) ATI(0): Virtual size is 640x480 (pitch 640)
(**) ATI(0):  Default mode "640x480": 25.2 MHz, 31.5 kHz, 60.0 Hz
(II) ATI(0): Modeline "640x480"   25.20  640 656 752 800  480 490 492 525 -hsync -vsync
(**) ATI(0):  Default mode "320x240": 12.6 MHz, 31.5 kHz, 60.1 Hz (D)
(II) ATI(0): Modeline "320x240"   12.60  320 328 376 400  240 245 246 262 doublescan -hsync -vsync
(==) ATI(0): DPI set to (75, 75)
(II) Loading sub module "xaa"
(II) LoadModule: "xaa"
(II) Loading /usr/X11R6/lib/modules/libxaa.a
(II) Module xaa: vendor="X.Org Foundation"
   compiled for 6.8.0, module version = 1.2.0
   ABI class: X.Org Video Driver, version 0.7
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Loading /usr/X11R6/lib/modules/libramdac.a
(II) Module ramdac: vendor="X.Org Foundation"
   compiled for 6.8.0, module version = 0.1.0
   ABI class: X.Org Video Driver, version 0.7
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/X11R6/lib/modules/libfb.a
(II) Module fb: vendor="X.Org Foundation"
   compiled for 6.8.0, module version = 1.0.0
   ABI class: X.Org ANSI C Emulation, version 0.2
(!!) ATI(0): Using composite sync to match input timing.
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"
(II) Loading /usr/X11R6/lib/modules/libi2c.a
(II) Module i2c: vendor="X.Org Foundation"
   compiled for 6.8.0, module version = 1.2.0
   ABI class: X.Org Video Driver, version 0.7
(WW) ATI(0): I2C bus Mach64 initialisation failure.
(II) ATI(0): I2C bus "Mach64" removed.
(II) do I need RAC?  No, I don't.
(II) resource ranges after preInit:
   [0] 0   1   0xe0008000 - 0xe0008fff (0x1000) MS[B]
   [1] 0   1   0xe1000000 - 0xe1ffffff (0x1000000) MS[B]
   [2] -1   1   0xffffffff - 0xffffffff (0x1) MX[B]
   [3] -1   1   0x000f0000 - 0x000fffff (0x10000) MX[B]
   [4] -1   1   0x000c0000 - 0x000effff (0x30000) MX[B]
   [5] -1   1   0x00000000 - 0x0009ffff (0xa0000) MX[B]
   [6] -1   1   0xe0000000 - 0xe0007fff (0x8000) MX[B]
   [7] -1   1   0xf1000000 - 0xf17fffff (0x800000) MX[B]
   [8] -1   1   0xf0000000 - 0xf0ffffff (0x1000000) MX[B]
   [9] -1   1   0xe0020000 - 0xe003ffff (0x20000) MX[B](B)
   [10] -1   1   0xe0008000 - 0xe0008fff (0x1000) MX[B](B)
   [11] -1   1   0xe1000000 - 0xe1ffffff (0x1000000) MX[B](B)
   [12] 0   1   0x00c00400 - 0x00c004ff (0x100) IS[B]
   [13] -1   1   0x00ffffff - 0x00ffffff (0x1) IX[B]
   [14] -1   1   0x00000000 - 0x00000000 (0x1) IX[B]
   [15] -1   1   0x00000400 - 0x0000041f (0x20) IX[B]
   [16] -1   1   0x00c00020 - 0x00c0002f (0x10) IX[B]
   [17] -1   1   0x00c00018 - 0x00c0001b (0x4) IX[B]
   [18] -1   1   0x00c00010 - 0x00c00017 (0x8) IX[B]
   [19] -1   1   0x00c00008 - 0x00c0000b (0x4) IX[B]
   [20] -1   1   0x00c00000 - 0x00c00007 (0x8) IX[B]
   [21] -1   1   0x00c00400 - 0x00c004ff (0x100) IX[B](B)
(II) ATI(0): Largest offscreen areas (with overlaps):
(II) ATI(0):    640 x 2795 rectangle at 0,480
(II) ATI(0):    128 x 2796 rectangle at 0,480
(II) ATI(0): Using XFree86 Acceleration Architecture (XAA)
   Screen to screen bit blits
   Solid filled rectangles
   8x8 mono pattern filled rectangles
   Indirect CPU to Screen color expansion
   Solid Lines
   Offscreen Pixmaps
   Setting up tile and stipple cache:
      32 128x128 slots
      18 256x256 slots
(==) ATI(0): Backing store disabled
(==) ATI(0): Silken mouse enabled
(==) RandR enabled
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension LBX
(II) Initializing built-in extension XC-APPGROUP
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension XFree86-Bigfont
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) Initializing built-in extension XEVIE
(**) Option "Protocol" "Auto"
(**) Mouse1: Device: "/dev/sunmouse"
(**) Mouse1: Protocol: "Auto"
(**) Option "CorePointer"
(**) Mouse1: Core Pointer
(**) Option "Device" "/dev/sunmouse"
(==) Mouse1: Emulate3Buttons, Emulate3Timeout: 50
(==) Mouse1: Buttons: 3
(**) Mouse1: SmartScroll: 1
(**) Option "CoreKeyboard"
(**) Keyboard1: Core Keyboard
(**) Option "Protocol" "standard"
(**) Keyboard1: Protocol: standard
(**) Option "AutoRepeat" "500 30"
(**) Option "XkbRules" "xfree86"
(**) Keyboard1: XkbRules: "xfree86"
(**) Option "XkbModel" "pc101"
(**) Keyboard1: XkbModel: "pc101"
(**) Option "XkbLayout" "us"
(**) Keyboard1: XkbLayout: "us"
(**) Option "CustomKeycodes" "off"
(**) Keyboard1: CustomKeycodes disabled
(II) XINPUT: Adding extended input device "Keyboard1" (type: KEYBOARD)
(II) XINPUT: Adding extended input device "Mouse1" (type: MOUSE)
(**) Option "Device" "/dev/sunmouse"
(II) Mouse1: GuessProtocol: setting mouse protocol to "PS/2"
Could not init font path element /usr/share/fonts/local/, removing from list!


f anyone can help me out, thanks in advance!
Back to top
View user's profile Send private message
fkryszon
n00b
n00b


Joined: 01 Nov 2004
Posts: 64
Location: Belgium

PostPosted: Mon Nov 22, 2004 10:27 pm    Post subject: Reply with quote

mayve not optimized but working on std ultra5:

# File generated by xorgconfig.

#
# Copyright 2004 The X.Org Foundation
#
# Permission is hereby granted, free of charge, to any person obtaining a
# copy of this software and associated documentation files (the "Software"),
# to deal in the Software without restriction, including without limitation
# the rights to use, copy, modify, merge, publish, distribute, sublicense,
# and/or sell copies of the Software, and to permit persons to whom the
# Software is furnished to do so, subject to the following conditions:
#
# The above copyright notice and this permission notice shall be included in
# all copies or substantial portions of the Software.
#
# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
# The X.Org Foundation BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
# WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF
# OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
# SOFTWARE.
#
# Except as contained in this notice, the name of The X.Org Foundation shall
# not be used in advertising or otherwise to promote the sale, use or other
# dealings in this Software without prior written authorization from
# The X.Org Foundation.
#

# **********************************************************************
# Refer to the xorg.conf(5x) man page for details about the format of
# this file.
# **********************************************************************

# **********************************************************************
# Module section -- this section is used to specify
# which dynamically loadable modules to load.
# **********************************************************************
#
Section "Module"

# This loads the DBE extension module.

Load "dbe" # Double buffer extension

# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
SubSection "extmod"
Option "omit xfree86-dga" # don't initialise the DGA extension
EndSubSection

# This loads the font modules
Load "type1"
# Load "speedo"
Load "freetype"
# Load "xtt"

# This loads the GLX module
# Load "glx"
# This loads the DRI module
# Load "dri"

EndSection

# **********************************************************************
# Files section. This allows default font and rgb paths to be set
# **********************************************************************

Section "Files"

# The location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.

RgbPath "/usr/X11R6/lib/X11/rgb"

# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
#
#

FontPath "/usr/share/fonts/misc/"
FontPath "/usr/share/fonts/TTF/"
FontPath "/usr/share/fonts/Type1/"
# FontPath "/usr/share/fonts/CID/"
FontPath "/usr/share/fonts/75dpi/"
FontPath "/usr/share/fonts/100dpi/"
FontPath "/usr/share/fonts/local/"
# FontPath "/usr/share/fonts/Speedo/"
# FontPath "/usr/share/fonts/TrueType/"
# FontPath "/usr/share/fonts/freefont/"

# The module search path. The default path is shown here.

# ModulePath "/usr/X11R6/lib/modules"

EndSection

# **********************************************************************
# Server flags section.
# **********************************************************************

Section "ServerFlags"

# Uncomment this to cause a core dump at the spot where a signal is
# received. This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging

# Option "NoTrapSignals"

# Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence
# (where n is 1 through 12). This allows clients to receive these key
# events.

# Option "DontVTSwitch"

# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
# This allows clients to receive this key event.

# Option "DontZap"

# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
# sequences. This allows clients to receive these key events.

# Option "Dont Zoom"

# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.

# Option "DisableVidModeExtension"

# Uncomment this to enable the use of a non-local xvidtune client.

# Option "AllowNonLocalXvidtune"

# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings.

# Option "DisableModInDev"

# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).

# Option "AllowNonLocalModInDev"

EndSection

# **********************************************************************
# Input devices
# **********************************************************************

# **********************************************************************
# Core keyboard's InputDevice section
# **********************************************************************

Section "InputDevice"

Identifier "Keyboard1"
Driver "keyboard"

# For most OSs the protocol can be omitted (it defaults to "Standard").
# When using XQUEUE (only for SVR3 and SVR4, but not Solaris),
# uncomment the following line.

# Option "Protocol" "Xqueue"

Option "AutoRepeat" "500 30"

# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
# Option "Xleds" "1 2 3"

# Option "LeftAlt" "Meta"
# Option "RightAlt" "ModeShift"

# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults). For example, for a non-U.S.
# keyboard, you will probably want to use:
# Option "XkbModel" "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
# Option "XkbModel" "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
# Option "XkbLayout" "de"
# or:
# Option "XkbLayout" "de"
# Option "XkbVariant" "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
# Option "XkbOptions" "ctrl:swapcaps"

# These are the default XKB settings for Xorg
# Option "XkbRules" "xorg"
# Option "XkbModel" "pc101"
# Option "XkbLayout" "us"
# Option "XkbVariant" ""
# Option "XkbOptions" ""

# Option "XkbDisable"

Option "XkbRules" "sun"
Option "XkbModel" "type5"
Option "XkbLayout" "us"

EndSection


# **********************************************************************
# Core Pointer's InputDevice section
# **********************************************************************

Section "InputDevice"

# Identifier and driver

Identifier "Mouse1"
Driver "mouse"
Option "Protocol" "Busmouse"
Option "Device" "/dev/sunmouse"

# Mouse-speed setting for PS/2 mouse.

# Option "Resolution" "256"

# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.

# Option "Protocol" "Xqueue"

# Baudrate and SampleRate are only for some Logitech mice. In
# almost every case these lines should be omitted.

# Option "BaudRate" "9600"
# Option "SampleRate" "150"

# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)

# Option "Emulate3Buttons"
# Option "Emulate3Timeout" "50"

# ChordMiddle is an option for some 3-button Logitech mice

# Option "ChordMiddle"

EndSection


# **********************************************************************
# Other input device sections
# this is optional and is required only if you
# are using extended input devices. This is for example only. Refer
# to the xorg.conf man page for a description of the options.
# **********************************************************************
#
# Section "InputDevice"
# Identifier "Mouse2"
# Driver "mouse"
# Option "Protocol" "MouseMan"
# Option "Device" "/dev/mouse2"
# EndSection
#
# Section "InputDevice"
# Identifier "spaceball"
# Driver "magellan"
# Option "Device" "/dev/cua0"
# EndSection
#
# Section "InputDevice"
# Identifier "spaceball2"
# Driver "spaceorb"
# Option "Device" "/dev/cua0"
# EndSection
#
# Section "InputDevice"
# Identifier "touchscreen0"
# Driver "microtouch"
# Option "Device" "/dev/ttyS0"
# Option "MinX" "1412"
# Option "MaxX" "15184"
# Option "MinY" "15372"
# Option "MaxY" "1230"
# Option "ScreenNumber" "0"
# Option "ReportingMode" "Scaled"
# Option "ButtonNumber" "1"
# Option "SendCoreEvents"
# EndSection
#
# Section "InputDevice"
# Identifier "touchscreen1"
# Driver "elo2300"
# Option "Device" "/dev/ttyS0"
# Option "MinX" "231"
# Option "MaxX" "3868"
# Option "MinY" "3858"
# Option "MaxY" "272"
# Option "ScreenNumber" "0"
# Option "ReportingMode" "Scaled"
# Option "ButtonThreshold" "17"
# Option "ButtonNumber" "1"
# Option "SendCoreEvents"
# EndSection

# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section "Monitor"

Identifier "My Monitor"

# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

HorizSync 31.5 - 57.0

# HorizSync 30-64 # multisync
# HorizSync 31.5, 35.2 # multiple fixed sync frequencies
# HorizSync 15-25, 30-50 # multiple ranges of sync frequencies

# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

VertRefresh 50-90

EndSection


# **********************************************************************
# Graphics device section
# **********************************************************************

# Any number of graphics device sections may be present

# Standard VGA Device:

Section "Device"
Identifier "Standard VGA"
VendorName "Unknown"
BoardName "Unknown"

# The chipset line is optional in most cases. It can be used to override
# the driver's chipset detection, and should not normally be specified.

# Chipset "generic"

# The Driver line must be present. When using run-time loadable driver
# modules, this line instructs the server to load the specified driver
# module. Even when not using loadable driver modules, this line
# indicates which driver should interpret the information in this section.

Driver "vga"
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for. When this line isn't present, a device
# section can only match up with the primary video device. For PCI
# devices a line like the following could be used. This line should not
# normally be included unless there is more than one video device
# intalled.

# BusID "PCI:0:10:0"

# VideoRam 256

# Clocks 25.2 28.3

EndSection

# Device configured by xorgconfig:

Section "Device"
Identifier "** ATI Rage 128 based (generic) [r128]"
Driver "ati"
VideoRam 4096
# Insert Clocks lines here if appropriate
EndSection


# **********************************************************************
# Screen sections
# **********************************************************************

# Any number of screen sections may be present. Each describes
# the configuration of a single screen. A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
Identifier "Screen 1"
Device "** ATI Rage 128 based (generic) [r128]"
Monitor "My Monitor"
DefaultDepth 24

Subsection "Display"
Depth 8
Modes "1024x768"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 16
Modes "1024x768"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 24
Modes "1024x768"
ViewPort 0 0
EndSubsection
EndSection

# **********************************************************************
# ServerLayout sections.
# **********************************************************************

# Any number of ServerLayout sections may be present. Each describes
# the way multiple screens are organised. A specific ServerLayout
# section may be specified from the X server command line with the
# "-layout" option. In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.

Section "ServerLayout"

# The Identifier line must be present
Identifier "Simple Layout"

# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens. The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen. In this example, screen 2 is located to the
# right of screen 1.

Screen "Screen 1"

# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used. Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".

InputDevice "Mouse1" "CorePointer"
InputDevice "Keyboard1" "CoreKeyboard"

EndSection

# Section "DRI"
# Mode 0666
# EndSection



i hope, that helps a bit
Back to top
View user's profile Send private message
frankvandamme
n00b
n00b


Joined: 03 May 2004
Posts: 11
Location: Boortmeerbeek, Belgium

PostPosted: Tue Nov 23, 2004 8:58 pm    Post subject: Reply with quote

Hm nope, forget it. This monitor needs all timings etc accurately specified (that is what fixed-frequency means), generic settings and ranges don't work.
Back to top
View user's profile Send private message
marky9074
Apprentice
Apprentice


Joined: 24 Sep 2004
Posts: 196
Location: UK

PostPosted: Tue Nov 23, 2004 10:57 pm    Post subject: Reply with quote

This may be an issue with the reference clock, a quick search in the forum gets the links below:

http://www.xfree86.org/~dawes/4.3.0/ati5.html#26.

https://forums.gentoo.org/viewtopic.php?t=196979&highlight=mach64+sparc

https://forums.gentoo.org/viewtopic.php?t=249153&highlight=reference+clock+sparc

Mark
Back to top
View user's profile Send private message
frankvandamme
n00b
n00b


Joined: 03 May 2004
Posts: 11
Location: Boortmeerbeek, Belgium

PostPosted: Thu Nov 25, 2004 4:35 pm    Post subject: Reply with quote

I solved this problem: the clue is, X uses a built-in horizontal and vertical refresh range if you don't specify them. Then, if the modelines and the refresh rates are incompatible, it discards the mode.

So the trick is to add a horizsync and vertrefresh that X likes (google the monitor's product id + manual for that).
Back to top
View user's profile Send private message
dberkholz
Developer
Developer


Joined: 18 Mar 2003
Posts: 1008
Location: Minneapolis, MN, USA

PostPosted: Sat Dec 18, 2004 10:01 am    Post subject: Reply with quote

fkryszon wrote:
mayve not optimized but working on std ultra5:

Thanks a bunch, this gave me some good tips for getting X up on my new u5.
Back to top
View user's profile Send private message
Display posts from previous:   
Reply to topic    Gentoo Forums Forum Index Gentoo on Sparc All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum