View previous topic :: View next topic |
Author |
Message |
killfire l33t
Joined: 04 Oct 2003 Posts: 618
|
Posted: Tue Aug 10, 2004 3:43 am Post subject: ibookg3 sleep/hfs+ stuff |
|
|
lemme pop back into the shell of a newb...
heres the thing. i have seen mentioned everywhere, but cannot seem to find specific instructions (or even general ones) on how to get the following working:
sleep on ibook g3, kernel 2.6.7
with a working kernel, support for everything i needed i think.... and when i close the lid on the laptop, it freezes... only done this a few times (need osx for internet anyway, so reboot alot)... so i havent tested by way of ssh whether the computrer is frozen, or just the screen. the point is, sleep is not working.
how to get read (and write) access for hfs+ filesystems, i enabled hfs+ in the kernel section for filesystems, but when i try to mount (whether with traditional mount -t hfs /dev/blah /mnt/macosx , or the sort of strange hmount) i only get the small README file that tells you to install a mac os....
i do not have journalling enabled..
hopefully this can be very clearly cleared up (because i know both are possible)
any kernel options, plus apps/ necesary configuration would be handy
thanks,
killfire |
|
Back to top |
|
|
DiskBreaker Apprentice
Joined: 07 Oct 2003 Posts: 224
|
Posted: Tue Aug 10, 2004 6:11 am Post subject: Re: ibookg3 sleep/hfs+ stuff |
|
|
killfire wrote: | sleep on ibook g3, kernel 2.6.7 |
You will need to emerge and configure pbbuttonsd and add it to your bootlevel.
killfire wrote: | how to get read (and write) access for hfs+ filesystems, i enabled hfs+ in the kernel section for filesystems, but when i try to mount (whether with traditional mount -t hfs /dev/blah /mnt/macosx , or the sort of strange hmount) i only get the small README file that tells you to install a mac os.... |
You are mounting an hfs+ partition as hfs. Whenever you do this you see a file explaining why you can't access your data like that (pretty user-friendly engineering by apple again
What you have to do is specify hfsplus as the partition type:
Code: | mount -t hfsplus /dev/blah /mnt/macosx |
hth,
disk |
|
Back to top |
|
|
marks n00b
Joined: 20 Oct 2002 Posts: 5
|
|
Back to top |
|
|
ruben Guru
Joined: 04 Jul 2003 Posts: 462
|
Posted: Tue Aug 10, 2004 1:56 pm Post subject: |
|
|
You don't happen to be running "mol" when you tried the sleep? I noticed that when i run mol, my G3 iBook will go to sleep, but doesn't wanna wake up. |
|
Back to top |
|
|
killfire l33t
Joined: 04 Oct 2003 Posts: 618
|
Posted: Tue Aug 10, 2004 6:42 pm Post subject: |
|
|
i have installed pbbuttonsd, configured it (thats how i did in 2.4)... i also disabled smp (as i dont have dual processors) .. before i posted here....
ill try to check preemptive kernell....
[EDIT]
checked, and i think this is the corresponding code:
Code: |
# CONFIG_SMP is not set
# CONFIG_PREEMPT is not set
# CONFIG_HIGHMEM is not set
CONFIG_KERNEL_ELF=y
|
so it seems that those are not set, either preempt or smp....
ill try again, i only tested this once or twice, and i may have recompiled my kernel since....
[/EDIT]
the hfs+ partitions were my mistake, i actually noticed it in a post after posting this....
i think the problem was that i had seen that mount supported hfs+, written like that, so i assumed that was the type that they used.....
thanks for the replies, will check back up on the kernel settings.
killfire[/code] |
|
Back to top |
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
|