Mitsumi-Brenner unter 2.6.6

[Moorenkopf]

Hi, ich hab' ein System mit 2.4er Kernel und eins mit 2.6.6er.
Unter letzterem läuft mein Brenner nicht, obwohl k3b ihn erkennt.

Brenner: Mitsumi CR-4802TE
Kernel: 2.6.6 Development

K3b-Log:
System
-----------------------
K3b Version: 0.11.9
KDE Version: 3.2.2
QT Version: 3.3.2

cdrecord
-----------------------
scsidev: '/dev/ide/host0/bus1/target1/lun0/cd'
devname: '/dev/ide/host0/bus1/target1/lun0/cd'
scsibus: -2 target: -2 lun: -2
Warning: Open by 'devname' is unintentional and not supported.
Linux sg driver version: 3.5.27
SCSI buffer size: 64512
Cdrecord-Clone 2.01a25 (i686-pc-linux-gnu) Copyright (C) 1995-2004 Jörg Schilling
TOC Type: 1 = CD-ROM
Using libscg version 'schily-0.8'.
atapi: 1
Device type : Removable CD-ROM
Version : 0
Response Format: 1
Vendor_info : 'MITSUMI '
Identifikation : 'CR-4802TE '
Revision : '1.4D'
Device seems to be: Philips CDD-522.
Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
Driver flags : MMC SWABAUDIO
Supported modes: TAO PACKET SAO SAO/R96R RAW/R16 RAW/R96P RAW/R96R
Drive buf size : 1638400 = 1600 KB
FIFO size : 4194304 = 4096 KB
Track 01: data 3 MB
Total size: 3 MB (00:23.36) = 1752 sectors
Lout start: 4 MB (00:25/27) = 1752 sectors
Current Secsize: 2048
ATIP info from disk:
Indicated writing power: 4
Is not unrestricted
Is not erasable
Disk sub type: Medium Type A, low Beta category (A-) (2)
ATIP start of lead in: -12508 (97:15/17)
ATIP start of lead out: 359845 (79:59/70)
Disk type: Short strategy type (Phthalocyanine or similar)
Manuf. index: 22
Manufacturer: Ritek Co.
Blocks total: 359845 Blocks current: 359845 Blocks remaining: 358093
Starting to write CD/DVD at speed 4 in dummy SAO mode for single session.
Last chance to quit, starting dummy write in 2 seconds.
1 seconds.
0 seconds. Operation starts.
resid: 198
/usr/bin/cdrecord: Success. mode select g1: scsi sendcmd: no error
CDB: 55 10 00 00 00 00 00 01 02 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 06 00 00 00 00 1A 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x1A Qual 0x00 (parameter list length error) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.002s timeout 200s
/usr/bin/cdrecord: Warning: using default CD write parameter data.
Mode Select Data 00 10 00 00 05 32 12 00 00 00 00 00 00 00 00 00 00 00 00 96 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
/usr/bin/cdrecord: Cannot open new session.
/usr/bin/cdrecord: Success. prevent/allow medium removal: scsi sendcmd: no error
CDB: 1E 00 00 00 00 00
status: 0x1 (GOOD STATUS)
cmd finished after 0.000s timeout 200s
/usr/bin/cdrecord: fifo had 57 puts and 0 gets.
/usr/bin/cdrecord: fifo was 0 times empty and 0 times full, min fill was 100%.
Waiting for reader process to fill input buffer ... input buffer ready.
Writing time: 2.383s

cdrecord comand:
-----------------------
/usr/bin/cdrecord -v gracetime=2 dev=/dev/ide/host0/bus1/target1/lun0/cd speed=4 -dao -dummy -eject -data -tsize=1752s -

mkisofs
-----------------------
1752
28.65% done, estimate finish Tue May 25 14:19:05 2004
57.65% done, estimate finish Tue May 25 14:19:05 2004
85.67% done, estimate finish Tue May 25 14:19:05 2004
Total translation table size: 0
Total rockridge attributes bytes: 4975
Total directory bytes: 10240
Path table size(bytes): 56
Max brk space used 0
1752 extents written (3 Mb)

mkisofs comand:
-----------------------
/usr/bin/mkisofs -gui -graft-points -V K3b data project -volset -A K3B THE CD KREATOR VERSION 0.11.9 (C) 2003 SEBASTIAN TRUEG AND THE K3B TEAM -P -p K3b - Version 0.11.9 -sysid LINUX -volset-size 1 -volset-seqno 1 -sort /tmp/kde-moorenkopf/k3b1GukVa.tmp -r -hide-list /tmp/kde-moorenkopf/k3bJRaWlc.tmp -l -iso-level 2 -path-list /tmp/kde-moorenkopf/k3bQWJSqa.tmp

[dakjo]

Und was macht er nicht ? Sieht doch alles OK aus oder ? Wie ist die fehlermeldung.

[Moorenkopf]

Keine weitere Fehlermeldung.. er schmeißt die cd raus