jpsollie
Guru
Joined: 17 Aug 2013
Posts: 324
|
 Posted: Thu Jul 04, 2019 12:08 pm Post subject: lm_sensors for nct6795 |
 |
|
I'd like to write a sensors.conf for the MSI B450I motherboard with a ryzen 5 2400GE CPU.
The board is equipped with a nct679 hardware monitoring chip.
Here are my sensor values:
| Code: |
amdgpu-pci-3800
Adapter: PCI adapter
vddgfx: N/A
vddnb: N/A
temp1: +29.0°C (crit = +80.0°C, hyst = +0.0°C)
k10temp-pci-00c3
Adapter: PCI adapter
Tdie: +29.8°C (high = +70.0°C)
Tctl: +29.8°C
nct6795-isa-0a20
Adapter: ISA adapter
Vcore: +0.67 V (min = +0.00 V, max = +1.74 V)
in1: +1.02 V (min = +0.00 V, max = +0.00 V) ALARM
AVCC: +3.36 V (min = +0.00 V, max = +0.00 V) ALARM
+3.3V: +3.34 V (min = +0.00 V, max = +0.00 V) ALARM
in4: +1.01 V (min = +0.00 V, max = +0.00 V) ALARM
in5: +0.15 V (min = +0.00 V, max = +0.00 V) ALARM
in6: +0.86 V (min = +0.00 V, max = +0.00 V) ALARM
3VSB: +3.34 V (min = +0.00 V, max = +0.00 V) ALARM
Vbat: +3.23 V (min = +0.00 V, max = +0.00 V) ALARM
in9: +1.85 V (min = +0.00 V, max = +0.00 V) ALARM
in10: +0.90 V (min = +0.00 V, max = +0.00 V) ALARM
in11: +0.60 V (min = +0.00 V, max = +0.00 V) ALARM
in12: +1.13 V (min = +0.00 V, max = +0.00 V) ALARM
in13: +0.68 V (min = +0.00 V, max = +0.00 V) ALARM
in14: +1.53 V (min = +0.00 V, max = +0.00 V) ALARM
fan1: 0 RPM (min = 0 RPM)
fan2: 0 RPM (min = 0 RPM)
fan3: 0 RPM (min = 0 RPM)
fan4: 0 RPM (min = 0 RPM)
fan5: 0 RPM (min = 0 RPM)
SYSTIN: +40.0°C (high = +0.0°C, hyst = +0.0°C) ALARM sensor = CPU diode
CPUTIN: +32.0°C (high = +115.0°C, hyst = +90.0°C) sensor = thermistor
AUXTIN0: +33.5°C (high = +115.0°C, hyst = +90.0°C) sensor = thermistor
AUXTIN1: +31.0°C sensor = thermistor
AUXTIN2: +50.0°C sensor = thermistor
AUXTIN3: -2.0°C sensor = thermistor
SMBUSMASTER 0: +29.5°C
PCH_CHIP_CPU_MAX_TEMP: +0.0°C
PCH_CHIP_TEMP: +0.0°C
PCH_CPU_TEMP: +0.0°C
intrusion0: ALARM
intrusion1: ALARM
beep_enable: disabled
iwlwifi-virtual-0
Adapter: Virtual device
temp1: +33.0°C
|
So, I see a lot of voltages here("in0"-"in14"), but what do they actually mean? how can I retrieve the recommended values I have to put in my sensors.conf?
Thx
_________________
The power of Gentoo optimization (not overclocked): [img]https://www.passmark.com/baselines/V10/images/503714802842.png[/img] |
|
Kernel & Hardware
