_dolan
n00b
Joined: 14 Mar 2018
Posts: 1
|
 Posted: Wed Mar 14, 2018 2:32 pm Post subject: Intel Graphics micro HDMI to VGA adapter not working |
 |
|
I have been struggling to get a micro HDMI to VGA adapter I recently bought working with my laptop. It is running gentoo kernel 4.12.12, with Intel HD Graphics 520 (Skylake). Everything works fine on my laptop's screen, but when I try to plug the micro HDMI adapter, connected to a monitor, into the micro HDMI port on my laptop, it doesn't get detected. What's weird is that if I put video=HDMI-A-1 on the kernel command line, the output works perfectly fine, and I can manipulate it using xrandr, however with that enabled, xrandr always shows it as connected, even if the adapter is disconnected, which I don't want.
Output of xrandr --verbose
| Code: |
Screen 0: minimum 320 x 200, current 1920 x 1080, maximum 8192 x 8192
eDP-1 connected primary 1920x1080+0+0 (0x45) normal (normal left inverted right x axis y axis) 293mm x 165mm
Identifier: 0x42
Timestamp: 138027
Subpixel: unknown
Gamma: 1.0:1.0:1.0
Brightness: 1.0
Clones:
CRTC: 0
CRTCs: 0 1 2
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
EDID:
00ffffffffffff0006af2d2700000000
10190104951d117802bc05a2554c9a25
0e505400000001010101010101010101
010101010101143780b8703824401010
3e0025a5100000180000000000000000
00000000000000000000000000fe0041
554f0a202020202020202020000000fe
004231333348414e30322e37200a0082
scaling mode: Full aspect
supported: None, Full, Center, Full aspect
Broadcast RGB: Automatic
supported: Automatic, Full, Limited 16:235
audio: auto
supported: force-dvi, off, auto, on
link-status: Good
supported: Good, Bad
1920x1080 (0x45) 141.000MHz -HSync -VSync *current +preferred
h: width 1920 start 1936 end 1952 total 2104 skew 0 clock 67.02KHz
v: height 1080 start 1083 end 1097 total 1116 clock 60.05Hz
1400x1050 (0x46) 122.000MHz +HSync +VSync
h: width 1400 start 1488 end 1640 total 1880 skew 0 clock 64.89KHz
v: height 1050 start 1052 end 1064 total 1082 clock 59.98Hz
1280x1024 (0x47) 108.000MHz +HSync +VSync
h: width 1280 start 1328 end 1440 total 1688 skew 0 clock 63.98KHz
v: height 1024 start 1025 end 1028 total 1066 clock 60.02Hz
1280x960 (0x48) 108.000MHz +HSync +VSync
h: width 1280 start 1376 end 1488 total 1800 skew 0 clock 60.00KHz
v: height 960 start 961 end 964 total 1000 clock 60.00Hz
1024x768 (0x49) 133.475MHz -HSync +VSync DoubleScan
h: width 1024 start 1100 end 1212 total 1400 skew 0 clock 95.34KHz
v: height 768 start 768 end 770 total 794 clock 60.04Hz
1024x768 (0x4a) 65.000MHz -HSync -VSync
h: width 1024 start 1048 end 1184 total 1344 skew 0 clock 48.36KHz
v: height 768 start 771 end 777 total 806 clock 60.00Hz
960x720 (0x4b) 117.000MHz -HSync +VSync DoubleScan
h: width 960 start 1024 end 1128 total 1300 skew 0 clock 90.00KHz
v: height 720 start 720 end 722 total 750 clock 60.00Hz
928x696 (0x4c) 109.150MHz -HSync +VSync DoubleScan
h: width 928 start 976 end 1088 total 1264 skew 0 clock 86.35KHz
v: height 696 start 696 end 698 total 719 clock 60.05Hz
896x672 (0x4d) 102.400MHz -HSync +VSync DoubleScan
h: width 896 start 960 end 1060 total 1224 skew 0 clock 83.66KHz
v: height 672 start 672 end 674 total 697 clock 60.01Hz
800x600 (0x4e) 81.000MHz +HSync +VSync DoubleScan
h: width 800 start 832 end 928 total 1080 skew 0 clock 75.00KHz
v: height 600 start 600 end 602 total 625 clock 60.00Hz
800x600 (0x4f) 40.000MHz +HSync +VSync
h: width 800 start 840 end 968 total 1056 skew 0 clock 37.88KHz
v: height 600 start 601 end 605 total 628 clock 60.32Hz
800x600 (0x50) 36.000MHz +HSync +VSync
h: width 800 start 824 end 896 total 1024 skew 0 clock 35.16KHz
v: height 600 start 601 end 603 total 625 clock 56.25Hz
700x525 (0x51) 61.000MHz +HSync +VSync DoubleScan
h: width 700 start 744 end 820 total 940 skew 0 clock 64.89KHz
v: height 525 start 526 end 532 total 541 clock 59.98Hz
640x512 (0x52) 54.000MHz +HSync +VSync DoubleScan
h: width 640 start 664 end 720 total 844 skew 0 clock 63.98KHz
v: height 512 start 512 end 514 total 533 clock 60.02Hz
640x480 (0x53) 54.000MHz +HSync +VSync DoubleScan
h: width 640 start 688 end 744 total 900 skew 0 clock 60.00KHz
v: height 480 start 480 end 482 total 500 clock 60.00Hz
640x480 (0x54) 25.175MHz -HSync -VSync
h: width 640 start 656 end 752 total 800 skew 0 clock 31.47KHz
v: height 480 start 490 end 492 total 525 clock 59.94Hz
512x384 (0x55) 32.500MHz -HSync -VSync DoubleScan
h: width 512 start 524 end 592 total 672 skew 0 clock 48.36KHz
v: height 384 start 385 end 388 total 403 clock 60.00Hz
400x300 (0x56) 20.000MHz +HSync +VSync DoubleScan
h: width 400 start 420 end 484 total 528 skew 0 clock 37.88KHz
v: height 300 start 300 end 302 total 314 clock 60.32Hz
400x300 (0x57) 18.000MHz +HSync +VSync DoubleScan
h: width 400 start 412 end 448 total 512 skew 0 clock 35.16KHz
v: height 300 start 300 end 301 total 312 clock 56.34Hz
320x240 (0x58) 12.587MHz -HSync -VSync DoubleScan
h: width 320 start 328 end 376 total 400 skew 0 clock 31.47KHz
v: height 240 start 245 end 246 total 262 clock 60.05Hz
HDMI-1 disconnected (normal left inverted right x axis y axis)
Identifier: 0x43
Timestamp: 138027
Subpixel: unknown
Clones:
CRTCs: 0 1 2
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
aspect ratio: Automatic
supported: Automatic, 4:3, 16:9
Broadcast RGB: Automatic
supported: Automatic, Full, Limited 16:235
audio: auto
supported: force-dvi, off, auto, on
link-status: Good
supported: Good, Bad
|
Device according to lspci -v
| Code: |
00:02.0 VGA compatible controller: Intel Corporation HD Graphics 520 (rev 07) (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. HD Graphics 520
Flags: bus master, fast devsel, latency 0, IRQ 123
Memory at de000000 (64-bit, non-prefetchable) [size=16M]
Memory at c0000000 (64-bit, prefetchable) [size=256M]
I/O ports at f000 [size=64]
[virtual] Expansion ROM at 000c0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: i915
Kernel modules: i915
|
Output of cat /sys/class/drm/card0-HDMI-A-1/status
What seems weird to me is the output of cat /sys/class/drm/card0-HDMI-A-1/enabled
which seems to me like the output is being actively disabled by something?
My xorg.conf
| Code: |
Section "Device"
Identifier "Device0"
BusID "PCI:00:02:0"
Driver "modesetting"
EndSection
|
I have tried manually enabling the output with xrandr
| Code: |
dylan@dylan-laptop ~ % xrandr --addmode HDMI-1 1920x1080
dylan@dylan-laptop ~ % xrandr --output HDMI-1 --mode 1920x1080 --right-of eDP-1
xrandr: Configure crtc 1 failed
|
(1920x1080 is a supported mode on this monitor)
Some additional information:
I am using i3wm gaps. My laptop is an ASUS ZenBook UX305LA.
Any help with this would be greatly appreciated! Thanks in advance! |
|
Kernel & Hardware
