Gentoo Forums
Gentoo Forums
Gentoo Forums
Quick Search: in
[Solved] Qualcomm Atheros QCA6174 802.11ac Not Working
View unanswered posts
View posts from last 24 hours

 
Reply to topic    Gentoo Forums Forum Index Networking & Security
View previous topic :: View next topic  
Author Message
yx681745
n00b
n00b


Joined: 29 Dec 2017
Posts: 10

PostPosted: Fri Dec 29, 2017 12:22 pm    Post subject: [Solved] Qualcomm Atheros QCA6174 802.11ac Not Working Reply with quote

I set wireless driver in kernel as [url] https://wiki.gentoo.org/wiki/Qualcomm_Atheros_QCA6174 [/url]
Code:
lspci -nnk
    02:00.0 Network controller [0280]: Qualcomm Atheros QCA6174 802.11ac Wireless Network Adapter [168c:003e] (rev 32)
        Subsystem: Bigfoot Networks, Inc. QCA6174 802.11ac Wireless Network Adapter [1a56:1535]
        Kernel driver in use: ath10k_pci
        Kernel modules: ath10k_pci
03:00.0 Ethernet controller [0200]: Qualcomm Atheros Killer E2400 Gigabit Ethernet Controller [1969:e0a1] (rev 10)
        Subsystem: Acer Incorporated [ALI] Killer E2400 Gigabit Ethernet Controller [1025:1051]
        Kernel driver in use: alx 



Code:
tree /sys/class/net                           
/sys/class/net
├── enp3s0 -> ../../devices/pci0000:00/0000:00:1c.3/0000:03:00.0/net/enp3s0
├── lo -> ../../devices/virtual/net/lo
├── sit0 -> ../../devices/virtual/net/sit0
└── wlp2s0 -> ../../devices/pci0000:00/0000:00:1c.0/0000:02:00.0/net/wlp2s0


Code:
dmesg | grep ath10k
[    2.847678] ath10k_pci 0000:02:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[    3.060709] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:02:00.0.bin failed with error -2
[    3.060741] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/cal-pci-0000:02:00.0.bin failed with error -2
[    3.060999] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA6174/hw3.0/firmware-6.bin failed with error -2
[    3.061041] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA6174/hw3.0/firmware-5.bin failed with error -2
[    3.063600] ath10k_pci 0000:02:00.0: qca6174 hw3.2 target 0x05030000 chip_id 0x00340aff sub 1a56:1535
[    3.063605] ath10k_pci 0000:02:00.0: kconfig debug 0 debugfs 0 tracing 0 dfs 0 testmode 0
[    3.065058] ath10k_pci 0000:02:00.0: firmware ver WLAN.RM.2.0-00180-QCARMSWPZ-1 api 4 features wowlan,ignore-otp,no-4addr-pad crc32 75dee6c5
[    3.129268] ath10k_pci 0000:02:00.0: found invalid board magic
[    3.129905] ath10k_pci 0000:02:00.0: board_file api 1 bmi_id N/A crc32 872f3cc5
[    3.715206] ath10k_pci 0000:02:00.0: htt-ver 3.26 wmi-op 4 htt-op 3 cal otp max-sta 32 raw 0 hwcrypto 1
[    3.777783] ath10k_pci 0000:02:00.0 wlp2s0: renamed from wlan0


Code:
 vim /etc/conf.d/net
dns_domain_enp3s0="Avalon"
config_enp3s0="dhcp"

~
Is net name wrong or something? Please check it, thanks!


Last edited by yx681745 on Sat Dec 30, 2017 4:37 am; edited 1 time in total
Back to top
View user's profile Send private message
yx681745
n00b
n00b


Joined: 29 Dec 2017
Posts: 10

PostPosted: Fri Dec 29, 2017 3:37 pm    Post subject: Reply with quote

Code:
dmesg | grep firmware
[    0.253369] i915 0000:00:02.0: Direct firmware load for i915/skl_dmc_ver1_26.bin failed with error -2
[    0.253374] i915 0000:00:02.0: Failed to load DMC firmware [https://01.org/linuxgraphics/downloads/firmware], disabling runtime power management.
[    0.457417] nouveau 0000:01:00.0: Direct firmware load for nvidia/gm204/gr/sw_nonctx.bin failed with error -2
[    3.483048] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:02:00.0.bin failed with error -2
[    3.483070] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/cal-pci-0000:02:00.0.bin failed with error -2
[    3.483254] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA6174/hw3.0/firmware-6.bin failed with error -2
[    3.483259] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA6174/hw3.0/firmware-5.bin failed with error -2
[    3.485954] ath10k_pci 0000:02:00.0: firmware ver WLAN.RM.2.0-00180-QCARMSWPZ-1 api 4 features wowlan,ignore-otp,no-4addr-pad crc32 75dee6c5
[  525.175721] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:02:00.0.bin failed with error -2
[  525.175730] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/cal-pci-0000:02:00.0.bin failed with error -2
[  525.175737] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA6174/hw3.0/firmware-6.bin failed with error -2
[  525.175744] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA6174/hw3.0/firmware-5.bin failed with error -2
[  525.176683] ath10k_pci 0000:02:00.0: firmware ver WLAN.RM.2.0-00180-QCARMSWPZ-1 api 4 features wowlan,ignore-otp,no-4addr-pad crc32 75dee6c5
Back to top
View user's profile Send private message
fedeliallalinea
Bodhisattva
Bodhisattva


Joined: 08 Mar 2003
Posts: 22304
Location: here

PostPosted: Fri Dec 29, 2017 3:47 pm    Post subject: Reply with quote

You can post output of commands
Code:
$ grep FIRMWARE /usr/src/linux/.config
$ grep ATH10K .config
$ grep  DRM_I915 .config

What version of sys-kernel/linux-firmware you installed?
_________________
Questions are guaranteed in life; Answers aren't.
Back to top
View user's profile Send private message
yx681745
n00b
n00b


Joined: 29 Dec 2017
Posts: 10

PostPosted: Fri Dec 29, 2017 4:35 pm    Post subject: Reply with quote

Code:
 grep FIRMWARE /usr/src/linux/.config
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FIRMWARE_IN_KERNEL=y
CONFIG_EXTRA_FIRMWARE=""
# CONFIG_DRM_LOAD_EDID_FIRMWARE is not set
# CONFIG_FIRMWARE_EDID is not set
CONFIG_FIRMWARE_MEMMAP=y
# CONFIG_GOOGLE_FIRMWARE is not set
# CONFIG_TEST_FIRMWARE is not set

grep ATH10K .config
CONFIG_ATH10K=m
CONFIG_ATH10K_PCI=m
# CONFIG_ATH10K_USB is not set
# CONFIG_ATH10K_DEBUG is not set
# CONFIG_ATH10K_DEBUGFS is not set
# CONFIG_ATH10K_TRACING is not set

grep  DRM_I915 .config
CONFIG_DRM_I915=y
# CONFIG_DRM_I915_ALPHA_SUPPORT is not set
CONFIG_DRM_I915_CAPTURE_ERROR=y
CONFIG_DRM_I915_COMPRESS_ERROR=y
CONFIG_DRM_I915_USERPTR=y
# CONFIG_DRM_I915_GVT is not set

My firmware version is 20170314.
I tried to use this [url] https://github.com/kvalo/ath10k-firmware/tree/master/QCA6174 [/url] but it did not work either.
Back to top
View user's profile Send private message
Jaglover
Watchman
Watchman


Joined: 29 May 2005
Posts: 7250
Location: Saint Amant, Acadiana

PostPosted: Fri Dec 29, 2017 4:40 pm    Post subject: Reply with quote

Quote:
[ 525.175721] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:02:00.0.bin failed with error -2
[ 525.175730] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/cal-pci-0000:02:00.0.bin failed with error -2
[ 525.175737] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA6174/hw3.0/firmware-6.bin failed with error -2
[ 525.175744] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA6174/hw3.0/firmware-5.bin failed with error -2
[ 525.176683] ath10k_pci 0000:02:00.0: firmware ver WLAN.RM.2.0-00180-QCARMSWPZ-1 api 4 features wowlan,ignore-otp,no-4addr-pad crc32 75dee6c5

The way I understand this it tries to load different versions of firmwares which are not found (error -2) and finally finds and loads firmware (last line).
There may be something else, does AP scan give any results?
_________________
Please learn how to denote units correctly!
Back to top
View user's profile Send private message
yx681745
n00b
n00b


Joined: 29 Dec 2017
Posts: 10

PostPosted: Fri Dec 29, 2017 5:18 pm    Post subject: Reply with quote

There is no scan result.
Code:
iw dev wlp2s0 link
Not connected.

I'm so confused but sorry i have to go to bed. I'll be online in 8 hours.
Back to top
View user's profile Send private message
Jaglover
Watchman
Watchman


Joined: 29 May 2005
Posts: 7250
Location: Saint Amant, Acadiana

PostPosted: Fri Dec 29, 2017 5:25 pm    Post subject: Reply with quote

Your command does not scan.

Code:
iwlist <device> scanning

_________________
Please learn how to denote units correctly!
Back to top
View user's profile Send private message
fedeliallalinea
Bodhisattva
Bodhisattva


Joined: 08 Mar 2003
Posts: 22304
Location: here

PostPosted: Fri Dec 29, 2017 7:29 pm    Post subject: Reply with quote

For i915 since is built-in try to add firmware in External firmware blobs to build into the kernel binary (see here).
For ath10k, I'm not sure, but try to unmask version 20171206 of sys-kernel/linux-firmware package
_________________
Questions are guaranteed in life; Answers aren't.
Back to top
View user's profile Send private message
yx681745
n00b
n00b


Joined: 29 Dec 2017
Posts: 10

PostPosted: Sat Dec 30, 2017 2:42 am    Post subject: Reply with quote

iwlist didn't work so tired this:
Code:
iw wlp2s0 scan
iw wlp2s0 scan
BSS 2c:30:33:32:3f:90(on wlp2s0)
   TSF: 400487464743 usec (4d, 15:14:47)
   freq: 2412
   beacon interval: 100 TUs
   capability: ESS Privacy ShortSlotTime (0x0411)
   signal: -9.00 dBm
   last seen: 4645 ms ago
   Information elements from Probe Response frame:
   SSID: NETGEAR46
   Supported rates: 1.0* 2.0* 5.5* 11.0* 9.0 18.0 36.0 54.0
   DS Parameter set: channel 1
   ERP: Barker_Preamble_Mode
   Extended supported rates: 6.0 12.0 24.0 48.0
   HT capabilities:
      Capabilities: 0x11ec
         HT20
         SM Power Save disabled
         RX HT20 SGI
         RX HT40 SGI
         TX STBC
         RX STBC 1-stream
         Max AMSDU length: 3839 bytes
         DSSS/CCK HT40
      Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
      Minimum RX AMPDU time spacing: 4 usec (0x05)
      HT RX MCS rate indexes supported: 0-15, 32
      HT TX MCS rate indexes are undefined
   HT operation:
       * primary channel: 1
       * secondary channel offset: no secondary
       * STA channel width: 20 MHz
       * RIFS: 0
       * HT protection: no
       * non-GF present: 0
       * OBSS non-GF present: 0
       * dual beacon: 0
       * dual CTS protection: 0
       * STBC beacon: 0
       * L-SIG TXOP Prot: 0
       * PCO active: 0
       * PCO phase: 0
   RSN:    * Version: 1
       * Group cipher: CCMP
       * Pairwise ciphers: CCMP
       * Authentication suites: PSK
       * Capabilities: 1-PTKSA-RC 1-GTKSA-RC (0x0000)
   Extended capabilities: HT Information Exchange Supported
   BSS Load:
       * station count: 0
       * channel utilisation: 67/255
       * available admission capacity: 31250 [*32us]
   WMM:    * Parameter version 1
       * BE: CW 15-1023, AIFSN 3
       * BK: CW 15-1023, AIFSN 7
       * VI: CW 7-15, AIFSN 2, TXOP 3008 usec
       * VO: CW 3-7, AIFSN 2, TXOP 1504 usec
   Overlapping BSS scan params:
       * passive dwell: 20 TUs
       * active dwell: 10 TUs
       * channel width trigger scan interval: 300 s
       * scan passive total per channel: 200 TUs
       * scan active total per channel: 20 TUs
       * BSS width channel transition delay factor: 5
       * OBSS Scan Activity Threshold: 0.25 %
   Extended capabilities: HT Information Exchange Supported
   Country: CN   Environment: Indoor/Outdoor
      Channels [1 - 13] @ 16 dBm
   WPS:    * Version: 1.0
       * Wi-Fi Protected Setup State: 2 (Configured)
       * Response Type: 3 (AP)
       * UUID: 38833092-3092-1883-ab77-2c3033323f90
       * Manufacturer: NETGEAR, Inc.
       * Model: NETGEAR Wireless Access Point
       * Model Number: R6220
       * Serial Number: 12345678
       * Primary Device Type: 6-0050f204-1
       * Device name: R6220 (Wireless AP)
       * Config methods: Label, Display, Keypad
       * RF Bands: 0x1
       * Unknown TLV (0x1049, 6 bytes): 00 37 2a 00 01 20
BSS a0:f4:79:11:8b:40(on wlp2s0)
   TSF: 3672950192943 usec (42d, 12:15:50)
   freq: 2417
   beacon interval: 100 TUs
   capability: ESS Privacy ShortSlotTime (0x0411)
   signal: -51.00 dBm
   last seen: 4631 ms ago
   Information elements from Probe Response frame:
   SSID: CU_qXr5
   Supported rates: 1.0* 2.0* 5.5* 11.0* 9.0 18.0 36.0 54.0
   DS Parameter set: channel 2
   ERP: Barker_Preamble_Mode
   Extended supported rates: 6.0 12.0 24.0 48.0
   HT capabilities:
      Capabilities: 0x106c
         HT20
         SM Power Save disabled
         RX HT20 SGI
         RX HT40 SGI
         No RX STBC
         Max AMSDU length: 3839 bytes
         DSSS/CCK HT40
      Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
      Minimum RX AMPDU time spacing: 4 usec (0x05)
      HT RX MCS rate indexes supported: 0-15, 32
      HT TX MCS rate indexes are undefined
   HT operation:
       * primary channel: 2
       * secondary channel offset: no secondary
       * STA channel width: 20 MHz
       * RIFS: 0
       * HT protection: no
       * non-GF present: 0
       * OBSS non-GF present: 0
       * dual beacon: 0
       * dual CTS protection: 0
       * STBC beacon: 0
       * L-SIG TXOP Prot: 0
       * PCO active: 0
       * PCO phase: 0
   RSN:    * Version: 1
       * Group cipher: CCMP
       * Pairwise ciphers: CCMP
       * Authentication suites: PSK
       * Capabilities: 1-PTKSA-RC 1-GTKSA-RC (0x0000)
   Extended capabilities: HT Information Exchange Supported
   BSS Load:
       * station count: 0
       * channel utilisation: 27/255
       * available admission capacity: 31250 [*32us]
   WMM:    * Parameter version 1
       * BE: CW 15-1023, AIFSN 3
       * BK: CW 15-1023, AIFSN 7
       * VI: CW 7-15, AIFSN 2, TXOP 3008 usec
       * VO: CW 3-7, AIFSN 2, TXOP 1504 usec
   Overlapping BSS scan params:
       * passive dwell: 20 TUs
       * active dwell: 10 TUs
       * channel width trigger scan interval: 300 s
       * scan passive total per channel: 200 TUs
       * scan active total per channel: 20 TUs
       * BSS width channel transition delay factor: 5
       * OBSS Scan Activity Threshold: 0.25 %
   Extended capabilities: HT Information Exchange Supported
   Country: CN   Environment: Indoor/Outdoor
      Channels [1 - 13] @ 16 dBm
   WPS:    * Version: 1.0
       * Wi-Fi Protected Setup State: 2 (Configured)
       * Response Type: 3 (AP)
       * UUID: bc329e00-1dd8-11b2-8601-a0f479118b40
       * Manufacturer: Huawei
       * Model: Huawei
       * Model Number: HG8347R
       * Serial Number: 12345678
       * Primary Device Type: 6-0050f204-1
       * Device name: Huawei ONT
       * Config methods: PBC
       * RF Bands: 0x1

... Scan works, but I edit /etc/wpa_supplicant/wpa_supplicant.conf as this
Code:
   
# reading passphrase from stdin
network={
        ssid="NETGEAR46"
        #psk="joyousballoon617"
        psk=3d22fce4a752fd5e8243cead06be3cd250565d72fe7defb0519adc9b008dc1f6
}
ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=wheel
update_config=1


Code:
wpa_supplicant -B -c /etc/wpa_supplicant/wpa_supplicant.conf -D ath10k_pci -dd -f /var/log/wpa.log -i wlp2s0 -t


still didn't work, additionally even I add "update_config" in conf file,
Code:
wpa_cli -i wlp2s0
Interactive mode

Could not connect to wpa_supplicant: wlp2s0 - re-trying


Code:
 dmesg | grep -i -E '02:00.0|wlp2s0|ath10k_pci|80211'
[    0.122165] pci 0000:02:00.0: [168c:003e] type 00 class 0x028000
[    0.122339] pci 0000:02:00.0: reg 0x10: [mem 0x84200000-0x843fffff 64bit]
[    0.122875] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[    3.572465] ath10k_pci 0000:02:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[    3.787592] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:02:00.0.bin failed with error -2
[    3.787612] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/cal-pci-0000:02:00.0.bin failed with error -2
[    3.787826] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA6174/hw3.0/firmware-6.bin failed with error -2
[    3.787839] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA6174/hw3.0/firmware-5.bin failed with error -2
[    3.790173] ath10k_pci 0000:02:00.0: qca6174 hw3.2 target 0x05030000 chip_id 0x00340aff sub 1a56:1535
[    3.790175] ath10k_pci 0000:02:00.0: kconfig debug 0 debugfs 0 tracing 0 dfs 0 testmode 0
[    3.790949] ath10k_pci 0000:02:00.0: firmware ver WLAN.RM.2.0-00180-QCARMSWPZ-1 api 4 features wowlan,ignore-otp,no-4addr-pad crc32 75dee6c5
[    3.853284] ath10k_pci 0000:02:00.0: found invalid board magic
[    3.853939] ath10k_pci 0000:02:00.0: board_file api 1 bmi_id N/A crc32 872f3cc5
[    4.436643] ath10k_pci 0000:02:00.0: htt-ver 3.26 wmi-op 4 htt-op 3 cal otp max-sta 32 raw 0 hwcrypto 1
[    4.499721] ath10k_pci 0000:02:00.0 wlp2s0: renamed from wlan0
[ 1447.718659] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
[ 5791.945364] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 5791.949584] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 5791.951217] wlp2s0: authenticated
[ 5791.951410] wlp2s0: associating with AP with corrupt probe response
[ 5791.952419] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 5791.956353] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 5791.959771] wlp2s0: associated
[ 5791.959819] IPv6: ADDRCONF(NETDEV_CHANGE): wlp2s0: link becomes ready
[ 5791.960059] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 5796.887374] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 5796.890827] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 5796.892381] wlp2s0: authenticated
[ 5796.892463] wlp2s0: associating with AP with corrupt probe response
[ 5796.893341] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 5796.897181] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 5796.900187] wlp2s0: associated
[ 5800.060905] wlp2s0: deauthenticated from 2c:30:33:32:3f:90 (Reason: 6=CLASS2_FRAME_FROM_NONAUTH_STA)
[ 5800.097082] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 5800.159814] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 5800.162175] wlp2s0: authenticated
[ 5800.162407] wlp2s0: associating with AP with corrupt probe response
[ 5800.163425] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 5800.167279] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 5800.170503] wlp2s0: associated
[ 5800.170697] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 5809.856863] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 5809.919440] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 5809.922918] wlp2s0: authenticated
[ 5809.923127] wlp2s0: associating with AP with corrupt probe response
[ 5809.923356] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 5809.927287] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 5809.930851] wlp2s0: associated
[ 5809.931052] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 5814.872697] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 5814.927642] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 5814.931119] wlp2s0: authenticated
[ 5814.931320] wlp2s0: associating with AP with corrupt probe response
[ 5814.931351] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 5814.936221] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 5814.939468] wlp2s0: associated
[ 5814.939685] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 5824.721576] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 5824.784101] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 5824.786799] wlp2s0: authenticated
[ 5824.787009] wlp2s0: associating with AP with corrupt probe response
[ 5824.787355] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 5824.791603] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 5824.795132] wlp2s0: associated
[ 5824.795409] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 5837.740354] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 5837.804413] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 5837.806053] wlp2s0: authenticated
[ 5837.806264] wlp2s0: associating with AP with corrupt probe response
[ 5837.806355] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 5837.810632] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 5837.813959] wlp2s0: associated
[ 5837.814173] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 5847.758394] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 5847.822490] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 5847.825620] wlp2s0: authenticated
[ 5847.825834] wlp2s0: associating with AP with corrupt probe response
[ 5847.826355] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 5847.832380] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 5847.835916] wlp2s0: associated
[ 5847.836128] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 5888.624439] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 5888.685665] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 5888.687227] wlp2s0: authenticated
[ 5888.687453] wlp2s0: associating with AP with corrupt probe response
[ 5888.688395] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 5888.693384] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 5888.697082] wlp2s0: associated
[ 5888.697303] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 5893.643567] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 5893.696981] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 5893.698600] wlp2s0: authenticated
[ 5893.698798] wlp2s0: associating with AP with corrupt probe response
[ 5893.699413] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 5893.705875] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 5893.709445] wlp2s0: associated
[ 5893.709720] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 5937.731422] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 5937.793234] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 5937.795523] wlp2s0: authenticated
[ 5937.795724] wlp2s0: associating with AP with corrupt probe response
[ 5937.796429] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 5937.800438] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 5937.803378] wlp2s0: associated
[ 5937.803639] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 5947.583506] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 5947.587264] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 5947.588944] wlp2s0: authenticated
[ 5947.589116] wlp2s0: associating with AP with corrupt probe response
[ 5947.589354] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 5947.593472] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 5947.596848] wlp2s0: associated
[ 5947.597087] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 5952.541271] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 5952.596493] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 5952.609334] wlp2s0: authenticated
[ 5952.609560] wlp2s0: associating with AP with corrupt probe response
[ 5952.610427] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 5952.615142] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 5952.618413] wlp2s0: associated
[ 5952.618642] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 5962.403362] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 5962.458454] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 5962.460048] wlp2s0: authenticated
[ 5962.460249] wlp2s0: associating with AP with corrupt probe response
[ 5962.460353] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 5962.467413] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 5962.470907] wlp2s0: associated
[ 5962.471131] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 5967.417799] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 5967.472877] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 5967.474864] wlp2s0: authenticated
[ 5967.475009] wlp2s0: associating with AP with corrupt probe response
[ 5967.475360] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 5967.479354] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 5967.482756] wlp2s0: associated
[ 5967.482988] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 5972.432052] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 5972.487074] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 5972.488866] wlp2s0: authenticated
[ 5972.489045] wlp2s0: associating with AP with corrupt probe response
[ 5972.489361] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 5972.493434] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 5972.496620] wlp2s0: associated
[ 5972.496839] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 6000.285392] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 6000.347316] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 6000.351018] wlp2s0: authenticated
[ 6000.351229] wlp2s0: associating with AP with corrupt probe response
[ 6000.351367] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 6000.357592] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 6000.361126] wlp2s0: associated
[ 6000.361383] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 6047.821027] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 6047.824445] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 6047.826120] wlp2s0: authenticated
[ 6047.826921] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 6047.888600] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 6047.890255] wlp2s0: authenticated
[ 6056.732255] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 6056.794370] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 6056.797083] wlp2s0: authenticated
[ 6056.797304] wlp2s0: associating with AP with corrupt probe response
[ 6056.797365] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 6056.802970] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 6056.806500] wlp2s0: associated
[ 6059.952912] wlp2s0: deauthenticated from 2c:30:33:32:3f:90 (Reason: 6=CLASS2_FRAME_FROM_NONAUTH_STA)
[ 6059.985027] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 6060.046679] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 6060.053021] wlp2s0: authenticated
[ 6060.053252] wlp2s0: associating with AP with corrupt probe response
[ 6060.054441] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 6060.059306] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 6060.062622] wlp2s0: associated
[ 6060.062845] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 6069.749981] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 6069.805022] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 6069.809082] wlp2s0: authenticated
[ 6069.809273] wlp2s0: associating with AP with corrupt probe response
[ 6069.810375] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 6069.814303] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 6069.817561] wlp2s0: associated
[ 6069.817729] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 6079.599274] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 6079.654577] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 6079.656197] wlp2s0: authenticated
[ 6079.656359] wlp2s0: associating with AP with corrupt probe response
[ 6079.656406] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 6079.660339] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 6079.663669] wlp2s0: associated
[ 6079.663881] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 6094.280280] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 6094.341937] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 6094.343590] wlp2s0: authenticated
[ 6094.343796] wlp2s0: associating with AP with corrupt probe response
[ 6094.344370] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 6094.348304] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 6094.351878] wlp2s0: associated
[ 6094.352078] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 6134.136815] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 6134.198642] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 6134.200766] wlp2s0: authenticated
[ 6134.200984] wlp2s0: associating with AP with corrupt probe response
[ 6134.201389] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 6134.205334] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 6134.208712] wlp2s0: associated
[ 6134.208909] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 6139.153230] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 6139.208007] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 6139.209712] wlp2s0: authenticated
[ 6139.209820] wlp2s0: associating with AP with corrupt probe response
[ 6139.210433] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 6139.214472] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 6139.217568] wlp2s0: associated
[ 6139.217705] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 6185.002515] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 6185.063778] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 6185.065317] wlp2s0: authenticated
[ 6185.065450] wlp2s0: associating with AP with corrupt probe response
[ 6185.066386] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 6185.070299] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 6185.073234] wlp2s0: associated
[ 6185.073365] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 6194.853100] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 6194.906484] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 6194.910972] wlp2s0: authenticated
[ 6194.911155] wlp2s0: associating with AP with corrupt probe response
[ 6194.912444] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 6194.918762] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 6194.922018] wlp2s0: associated
[ 6194.922244] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 6262.541020] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 6262.602688] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 6262.604618] wlp2s0: authenticated
[ 6262.604797] wlp2s0: associating with AP with corrupt probe response
[ 6262.605379] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 6262.609245] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 6262.612508] wlp2s0: associated
[ 6262.612712] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 6287.401515] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 6287.462914] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 6287.464576] wlp2s0: authenticated
[ 6287.464768] wlp2s0: associating with AP with corrupt probe response
[ 6287.465444] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 6287.469452] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 6287.473076] wlp2s0: associated
[ 6287.473291] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 6297.254488] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 6297.309402] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 6297.310971] wlp2s0: authenticated
[ 6297.311111] wlp2s0: associating with AP with corrupt probe response
[ 6297.311386] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 6297.317993] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 6297.321185] wlp2s0: associated
[ 6297.321411] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 6376.107357] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 6376.168576] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 6376.170145] wlp2s0: authenticated
[ 6376.170345] wlp2s0: associating with AP with corrupt probe response
[ 6376.170424] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 6376.174508] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 6376.178216] wlp2s0: associated
[ 6376.178455] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 6426.969851] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 6427.032257] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 6427.033887] wlp2s0: authenticated
[ 6427.034115] wlp2s0: associating with AP with corrupt probe response
[ 6427.034391] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 6427.040930] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 6427.044520] wlp2s0: associated
[ 6427.044781] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 6436.826199] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 6436.879471] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 6436.882041] wlp2s0: authenticated
[ 6436.882253] wlp2s0: associating with AP with corrupt probe response
[ 6436.882387] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 6436.888928] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 6436.892776] wlp2s0: associated
[ 6436.892978] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 6472.511681] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 6472.574026] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 6472.575602] wlp2s0: authenticated
[ 6472.575796] wlp2s0: associating with AP with corrupt probe response
[ 6472.576405] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 6472.580350] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 6472.583454] wlp2s0: associated
[ 6472.583689] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 6548.038818] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 6548.100896] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 6548.104324] wlp2s0: authenticated
[ 6548.104525] wlp2s0: associating with AP with corrupt probe response
[ 6548.105465] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 6548.110036] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 6548.113561] wlp2s0: associated
[ 6548.113772] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 6562.732345] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 6562.794148] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 6562.795801] wlp2s0: authenticated
[ 6562.796016] wlp2s0: associating with AP with corrupt probe response
[ 6562.796395] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 6562.801134] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 6562.804865] wlp2s0: associated
[ 6562.805083] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 6577.420758] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 6577.484114] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 6577.486278] wlp2s0: authenticated
[ 6577.486491] wlp2s0: associating with AP with corrupt probe response
[ 6577.487467] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 6577.492288] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 6577.495996] wlp2s0: associated
[ 6577.496208] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 6655.277742] wlp2s0: authenticate with 2c:30:33:32:3f:90
[ 6655.339980] wlp2s0: send auth to 2c:30:33:32:3f:90 (try 1/3)
[ 6655.342137] wlp2s0: authenticated
[ 6655.342337] wlp2s0: associating with AP with corrupt probe response
[ 6655.342395] wlp2s0: associate with 2c:30:33:32:3f:90 (try 1/3)
[ 6655.349981] wlp2s0: RX AssocResp from 2c:30:33:32:3f:90 (capab=0x411 status=0 aid=1)
[ 6655.353208] wlp2s0: associated
[ 6655.353433] wlp2s0: deauthenticating from 2c:30:33:32:3f:90 by local choice (Reason: 3=DEAUTH_LEAVING)

[/url]
Back to top
View user's profile Send private message
Jaglover
Watchman
Watchman


Joined: 29 May 2005
Posts: 7250
Location: Saint Amant, Acadiana

PostPosted: Sat Dec 30, 2017 2:47 am    Post subject: Reply with quote

It sounds like your wpa_supplicant is started in two (or more) ways. Make sure there is only one service that starts it.
_________________
Please learn how to denote units correctly!
Back to top
View user's profile Send private message
yx681745
n00b
n00b


Joined: 29 Dec 2017
Posts: 10

PostPosted: Sat Dec 30, 2017 3:11 am    Post subject: Reply with quote

Good news is
Code:

wpa_supplicant -B -c /etc/wpa_supplicant/wpa_supplicant.conf -D nl80211,wext -dd -f /var/log/wpa.log -i wlp2s0 -t

finally there is some reaction from wpa_gui and I can access to wpa_cli as well.
Bad news is after connecting to a Wifi there in no internet access still.

Code:
wpa_cli -i wlp2s0
> enable net 2
OK
<3>CTRL-EVENT-TERMINATING
Connection to wpa_supplicant lost - trying to reconnect
Connection to wpa_supplicant re-established
<3>CTRL-EVENT-SCAN-STARTED
<3>CTRL-EVENT-REGDOM-CHANGE init=BEACON_HINT type=UNKNOWN
<3>CTRL-EVENT-REGDOM-CHANGE init=BEACON_HINT type=UNKNOWN
<3>CTRL-EVENT-REGDOM-CHANGE init=BEACON_HINT type=UNKNOWN
<3>CTRL-EVENT-SCAN-RESULTS
<3>SME: Trying to authenticate with 2c:30:33:32:3f:94 (SSID='NETGEAR46-5G' freq=5745 MHz)
<3>Trying to associate with 2c:30:33:32:3f:94 (SSID='NETGEAR46-5G' freq=5745 MHz)
<3>Associated with 2c:30:33:32:3f:94
<3>CTRL-EVENT-SUBNET-STATUS-UPDATE status=0
<3>CTRL-EVENT-REGDOM-CHANGE init=COUNTRY_IE type=COUNTRY alpha2=CN
<3>WPA: Key negotiation completed with 2c:30:33:32:3f:94 [PTK=CCMP GTK=CCMP]
<3>CTRL-EVENT-CONNECTED - Connection to 2c:30:33:32:3f:94 completed [id=1 id_str=]


should I ln dhcp to wlp2s0?
Back to top
View user's profile Send private message
yx681745
n00b
n00b


Joined: 29 Dec 2017
Posts: 10

PostPosted: Sat Dec 30, 2017 3:40 am    Post subject: Reply with quote

After
Code:
dhcpcd wlp2s0

Problem solved!
Thank you @Jaglover @fedeliallalinea
However I want to know how cant I let gentoo automatically switch to wireless when I unplug. Is there a script can help do this?
Back to top
View user's profile Send private message
Jaglover
Watchman
Watchman


Joined: 29 May 2005
Posts: 7250
Location: Saint Amant, Acadiana

PostPosted: Sat Dec 30, 2017 3:53 am    Post subject: Reply with quote

I'm using wicd myself, does exactly that. Again, make sure only wicd will manage your connections if you choose to use it.

Code:
* net-misc/wicd
     Available versions:  1.7.4-r3 {X ambiance doc gnome-shell +gtk ioctl libnotify mac4lin ncurses nls +pm-utils PYTHON_TARGETS="python2_7"}
     Homepage:            https://launchpad.net/wicd
     Description:         A lightweight wired and wireless network manager for Linux

_________________
Please learn how to denote units correctly!
Back to top
View user's profile Send private message
yx681745
n00b
n00b


Joined: 29 Dec 2017
Posts: 10

PostPosted: Sat Dec 30, 2017 3:55 am    Post subject: Reply with quote

Reminder That if anyone using ath_10k_pci you should add -D wext when starting wpa_supplicant service.
Back to top
View user's profile Send private message
yx681745
n00b
n00b


Joined: 29 Dec 2017
Posts: 10

PostPosted: Sat Dec 30, 2017 4:34 am    Post subject: Reply with quote

I will check that package later, should I delete dhcp service from startip when configuring wicd?
Appreciate for your help again and I will tag this thread solved. I like your signature btw :twisted:
Back to top
View user's profile Send private message
Display posts from previous:   
Reply to topic    Gentoo Forums Forum Index Networking & Security All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum