Gentoo Forums
Gentoo Forums
Gentoo Forums
Quick Search: in
RocketRaid 640 issue [SOLVED]
View unanswered posts
View posts from last 24 hours

 
Reply to topic    Gentoo Forums Forum Index Kernel & Hardware
View previous topic :: View next topic  
Author Message
esperto
Apprentice
Apprentice


Joined: 27 Dec 2004
Posts: 158
Location: Brazil

PostPosted: Mon Jan 02, 2017 5:22 pm    Post subject: RocketRaid 640 issue [SOLVED] Reply with quote

Hi all,

I've installed a rocketraid 640 card in my system, but I'm facing issues.
I've followed the wiki (https://wiki.gentoo.org/wiki/HighPoint_RocketRAID), compiled the correct module for my card, rr64x, but when I try to load the module dmesg shows the below and during the modprobe the system hangs and come back a few times.

Code:

[ 1676.028664] rr64x: disagrees about version of symbol module_layout
[ 1710.509984] rr64x: disagrees about version of symbol module_layout
[ 1781.745232] rr64x: disagrees about version of symbol module_layout
[ 1876.077336] rr64x: module license 'Proprietary' taints kernel.
[ 1876.077344] Disabling lock debugging due to kernel taint
[ 1876.077527] rr64x: module verification failed: signature and/or required key missing - tainting kernel
[ 1876.078412] rr64x:RocketRAID 64x SATA controller driver v1.1 
[ 1876.205607] rr64x:adapter at PCI 5:0:0, IRQ 17
[ 1876.217076] rr64x:adapter at PCI 6:0:0, IRQ 17
[ 1876.218774] rr64x:[0 0  ] start port.
[ 1876.218775] rr64x:[0 0  ] start port hard reset (probe 1).
[ 1876.418812] rr64x:[0 1  ] start port.
[ 1876.418814] rr64x:[0 1  ] start port hard reset (probe 1).
[ 1876.618855] rr64x:[1 0  ] start port.
[ 1876.618858] rr64x:[1 0  ] start port hard reset (probe 1).
[ 1876.717401] DMAR: DRHD: handling fault status reg 2
[ 1876.717404] DMAR: DMAR:[DMA Write] Request device [05:00.1] fault addr a7878000
               DMAR:[fault reason 05] PTE Write access is not set                                                       
[ 1876.818893] rr64x:[1 1  ] start port.
[ 1876.818895] rr64x:[1 1  ] start port hard reset (probe 1).
[ 1879.401361] rr64x:[0 1  ] failed to hard reset.
[ 1879.401378] rr64x:[0 1  ] failed to perform port hard reset.
[ 1879.420360] rr64x:[0 0  ] start port soft reset (probe 1).
[ 1879.921001] DMAR: DRHD: handling fault status reg 2
[ 1879.921004] DMAR: DMAR:[DMA Read] Request device [05:00.1] fault addr abb78000
               DMAR:[fault reason 06] PTE Read access is not set                                                         
[ 1881.422752] rr64x:[0 0 f] failed to send 1st FIS
[ 1881.423400] rr64x:[1 0  ] failed to hard reset.
[ 1881.423416] rr64x:[1 0  ] failed to perform port hard reset.
[ 1881.423418] rr64x:[0 0  ] start port hard reset (probe 2).
[ 1881.624481] rr64x:[1 1  ] failed to hard reset.
[ 1881.624504] rr64x:[1 1  ] failed to perform port hard reset.
[ 1881.773226] DMAR: DRHD: handling fault status reg 2
[ 1881.773238] DMAR: DMAR:[DMA Write] Request device [05:00.1] fault addr a7878000
               DMAR:[fault reason 05] PTE Write access is not set                                                       
[ 1884.433475] rr64x:[0 0  ] start port soft reset (probe 2).
[ 1884.934117] DMAR: DRHD: handling fault status reg 2
[ 1884.934120] DMAR: DMAR:[DMA Read] Request device [05:00.1] fault addr abb78000
               DMAR:[fault reason 06] PTE Read access is not set                                                         
[ 1886.435920] rr64x:[0 0 f] failed to send 1st FIS
[ 1886.624533] rr64x:[0 0  ] start port hard reset (probe 3).
[ 1886.974309] DMAR: DRHD: handling fault status reg 2
[ 1886.974317] DMAR: DMAR:[DMA Write] Request device [05:00.1] fault addr a7878000
               DMAR:[fault reason 05] PTE Write access is not set                                                       
[ 1889.833572] rr64x:[0 0  ] start port soft reset (probe 3).
[ 1890.334227] DMAR: DRHD: handling fault status reg 2
[ 1890.334230] DMAR: DMAR:[DMA Read] Request device [05:00.1] fault addr abb78000
               DMAR:[fault reason 06] PTE Read access is not set                                                         
[ 1891.835986] rr64x:[0 0 f] failed to send 1st FIS
[ 1891.836251] psmouse serio1: Wheel Mouse at isa0060/serio1/input0 lost synchronization, throwing 1 bytes away.
[ 1891.836607] rr64x:[0 0  ] start port hard reset (probe 4).
[ 1892.186621] DMAR: DRHD: handling fault status reg 2
[ 1892.186640] DMAR: DMAR:[DMA Write] Request device [05:00.1] fault addr a7878000
               DMAR:[fault reason 05] PTE Write access is not set                                                       
[ 1894.841721] rr64x:[0 0  ] start port soft reset (probe 4).
[ 1895.342358] DMAR: DRHD: handling fault status reg 2
[ 1895.342362] DMAR: DMAR:[DMA Read] Request device [05:00.1] fault addr abb78000
               DMAR:[fault reason 06] PTE Read access is not set                                                         
[ 1896.844145] rr64x:[0 0 f] failed to send 1st FIS
[ 1896.844165] rr64x:[0 0  ] start port hard reset (probe 5).
[ 1897.194096] DMAR: DRHD: handling fault status reg 2
[ 1897.194109] DMAR: DMAR:[DMA Write] Request device [05:00.1] fault addr a7878000
               DMAR:[fault reason 05] PTE Write access is not set
[ 1899.849797] rr64x:[0 0  ] start port soft reset (probe 5).
[ 1900.350442] DMAR: DRHD: handling fault status reg 2
[ 1900.350445] DMAR: DMAR:[DMA Read] Request device [05:00.1] fault addr abb78000
               DMAR:[fault reason 06] PTE Read access is not set
[ 1901.852201] rr64x:[0 0 f] failed to send 1st FIS
[ 1902.052856] rr64x:[0 0  ] start port hard reset (probe 6).
[ 1902.402941] DMAR: DRHD: handling fault status reg 2
[ 1902.402947] DMAR: DMAR:[DMA Write] Request device [05:00.1] fault addr a7878000
               DMAR:[fault reason 05] PTE Write access is not set
[ 1905.097929] rr64x:[0 0  ] start port soft reset (probe 6).
[ 1905.598583] DMAR: DRHD: handling fault status reg 2
[ 1905.598587] DMAR: DMAR:[DMA Read] Request device [05:00.1] fault addr abb78000
               DMAR:[fault reason 06] PTE Read access is not set
[ 1907.100317] rr64x:[0 0 f] failed to send 1st FIS
[ 1907.298970] rr64x:[0 0  ] start port hard reset (probe 7).
[ 1907.648997] DMAR: DRHD: handling fault status reg 2
[ 1907.649010] DMAR: DMAR:[DMA Write] Request device [05:00.1] fault addr a7878000
               DMAR:[fault reason 05] PTE Write access is not set
[ 1910.434086] rr64x:[0 0  ] start port soft reset (probe 7).
[ 1910.934724] DMAR: DRHD: handling fault status reg 2
[ 1910.934727] DMAR: DMAR:[DMA Read] Request device [05:00.1] fault addr abb78000
               DMAR:[fault reason 06] PTE Read access is not set
[ 1912.436459] rr64x:[0 0 f] failed to send 1st FIS
[ 1912.437094] rr64x:[0 0  ] start port hard reset (probe 8).
[ 1912.787235] DMAR: DRHD: handling fault status reg 2
[ 1912.787248] DMAR: DMAR:[DMA Write] Request device [05:00.1] fault addr a7878000
               DMAR:[fault reason 05] PTE Write access is not set
[ 1915.442163] rr64x:[0 0  ] start port soft reset (probe 8).
[ 1915.942832] DMAR: DRHD: handling fault status reg 2
[ 1915.942836] DMAR: DMAR:[DMA Read] Request device [05:00.1] fault addr abb78000
               DMAR:[fault reason 06] PTE Read access is not set
[ 1917.444575] rr64x:[0 0 f] failed to send 1st FIS
[ 1917.644237] rr64x:[0 0  ] start port hard reset (probe 9).
[ 1917.994313] DMAR: DRHD: handling fault status reg 2
[ 1917.994319] DMAR: DMAR:[DMA Write] Request device [05:00.1] fault addr a7878000
               DMAR:[fault reason 05] PTE Write access is not set
[ 1920.850289] rr64x:[0 0  ] start port soft reset (probe 9).
[ 1921.350925] DMAR: DRHD: handling fault status reg 2
[ 1921.350928] DMAR: DMAR:[DMA Read] Request device [05:00.1] fault addr abb78000
               DMAR:[fault reason 06] PTE Read access is not set
[ 1922.852679] rr64x:[0 0 f] failed to send 1st FIS
[ 1922.852717] rr64x:[0 0  ] start port hard reset (probe 10).
[ 1923.202702] DMAR: DRHD: handling fault status reg 2
[ 1923.202706] DMAR: DMAR:[DMA Write] Request device [05:00.1] fault addr a7878000
               DMAR:[fault reason 05] PTE Write access is not set
[ 1925.858407] rr64x:[0 0  ] start port soft reset (probe a).
[ 1926.359049] DMAR: DRHD: handling fault status reg 2
[ 1926.359053] DMAR: DMAR:[DMA Read] Request device [05:00.1] fault addr abb78000
               DMAR:[fault reason 06] PTE Read access is not set
[ 1927.860820] rr64x:[0 0 f] failed to send 1st FIS
[ 1927.860850] rr64x:[0 0  ] start port hard reset (probe 11).
[ 1928.210819] DMAR: DRHD: handling fault status reg 2
[ 1928.210824] DMAR: DMAR:[DMA Write] Request device [05:00.1] fault addr a7878000
               DMAR:[fault reason 05] PTE Write access is not set
[ 1930.866557] rr64x:[0 0  ] start port soft reset (probe b).
[ 1931.367195] DMAR: DRHD: handling fault status reg 2
[ 1931.367199] DMAR: DMAR:[DMA Read] Request device [05:00.1] fault addr abb78000
               DMAR:[fault reason 06] PTE Read access is not set
[ 1932.868936] rr64x:[0 0 f] failed to send 1st FIS


I guess the first few messages give a hint, by what should I do? Does anyone here have experience with this card? I've got another system with windows and when the card was installed there, it seems to work fine.
I don't need the hardware RAID (or hardware-ish RAID) to work, I actually only need the extra ports.

for reference, this is the relevant part of lspci -v output (this card has a PLX chip, which the driver loads fine, a marvell IDE/SATA controller, which also seems to load fine, altough I cannot see new drives in /dev (only seeing sda), and the RocketRAID controller is seen by lspci but the kernel module seems not to load)

Code:

03:00.0 PCI bridge: PLX Technology, Inc. PEX 8608 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba) (prog-if 00 [Normal decode])
        Flags: bus master, fast devsel, latency 0, IRQ 16
        Memory at f7200000 (32-bit, non-prefetchable) [size=128K]
        Bus: primary=03, secondary=04, subordinate=08, sec-latency=0
        I/O behind bridge: 0000d000-0000efff
        Memory behind bridge: f7000000-f71fffff
        Capabilities: [40] Power Management version 3
        Capabilities: [48] MSI: Enable- Count=1/4 Maskable+ 64bit+
        Capabilities: [68] Express Upstream Port, MSI 00
        Capabilities: [a4] Subsystem: PLX Technology, Inc. PEX 8608 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch
        Kernel driver in use: pcieport

04:01.0 PCI bridge: PLX Technology, Inc. PEX 8608 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba) (prog-if 00 [Normal decode])
        Flags: bus master, fast devsel, latency 0, IRQ 17
        Bus: primary=04, secondary=05, subordinate=05, sec-latency=0
        I/O behind bridge: 0000e000-0000efff
        Memory behind bridge: f7100000-f71fffff
        Capabilities: [40] Power Management version 3
        Capabilities: [48] MSI: Enable- Count=1/4 Maskable+ 64bit+
        Capabilities: [68] Express Downstream Port (Slot+), MSI 00
        Capabilities: [a4] Subsystem: PLX Technology, Inc. PEX 8608 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch
        Kernel driver in use: pcieport

04:05.0 PCI bridge: PLX Technology, Inc. PEX 8608 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba) (prog-if 00 [Normal decode])
        Flags: bus master, fast devsel, latency 0, IRQ 17
        Bus: primary=04, secondary=06, subordinate=06, sec-latency=0
        I/O behind bridge: 0000d000-0000dfff
        Memory behind bridge: f7000000-f70fffff
        Capabilities: [40] Power Management version 3
        Capabilities: [48] MSI: Enable- Count=1/4 Maskable+ 64bit+
        Capabilities: [68] Express Downstream Port (Slot+), MSI 00
        Capabilities: [a4] Subsystem: PLX Technology, Inc. PEX 8608 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch
        Kernel driver in use: pcieport

04:07.0 PCI bridge: PLX Technology, Inc. PEX 8608 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba) (prog-if 00 [Normal decode])
        Flags: bus master, fast devsel, latency 0, IRQ 19
        Bus: primary=04, secondary=07, subordinate=07, sec-latency=0
        Capabilities: [40] Power Management version 3
        Capabilities: [48] MSI: Enable- Count=1/4 Maskable+ 64bit+
        Capabilities: [68] Express Downstream Port (Slot+), MSI 00
        Capabilities: [a4] Subsystem: PLX Technology, Inc. PEX 8608 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch
        Kernel driver in use: pcieport

04:09.0 PCI bridge: PLX Technology, Inc. PEX 8608 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba) (prog-if 00 [Normal decode])
        Flags: bus master, fast devsel, latency 0, IRQ 17
        Bus: primary=04, secondary=08, subordinate=08, sec-latency=0
        Capabilities: [40] Power Management version 3
        Capabilities: [48] MSI: Enable- Count=1/4 Maskable+ 64bit+
        Capabilities: [68] Express Downstream Port (Slot+), MSI 00
        Capabilities: [a4] Subsystem: PLX Technology, Inc. PEX 8608 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch
        Kernel driver in use: pcieport

05:00.0 RAID bus controller: HighPoint Technologies, Inc. RocketRAID 640 4 Port SATA-III Controller (rev 01)
        Subsystem: HighPoint Technologies, Inc. RocketRAID 640 4 Port SATA-III Controller
        Flags: bus master, fast devsel, latency 0, IRQ 17
        I/O ports at e090 [size=8]
        I/O ports at e080 [size=4]
        I/O ports at e070 [size=8]
        I/O ports at e060 [size=4]
        I/O ports at e050 [size=16]
        Memory at f7121000 (32-bit, non-prefetchable) [size=2K]
        Expansion ROM at f7110000 [disabled] [size=64K]
        Capabilities: [40] Power Management version 3
        Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit-
        Capabilities: [70] Express Legacy Endpoint, MSI 00

05:00.1 IDE interface: Marvell Technology Group Ltd. 88SE912x IDE Controller (rev 11) (prog-if 8f [Master SecP SecO PriP PriO])
        Subsystem: Marvell Technology Group Ltd. 88SE912x IDE Controller
        Flags: bus master, fast devsel, latency 0, IRQ 18
        I/O ports at e040 [size=8]
        I/O ports at e030 [size=4]
        I/O ports at e020 [size=8]
        I/O ports at e010 [size=4]
        I/O ports at e000 [size=16]
        Memory at f7120000 (32-bit, non-prefetchable) [size=16]
        Expansion ROM at f7100000 [disabled] [size=64K]
        Capabilities: [40] Power Management version 3
        Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit-
        Capabilities: [70] Express Legacy Endpoint, MSI 00
        Kernel driver in use: pata_marvell
        Kernel modules: pata_marvell, pata_acpi, ata_generic

06:00.0 RAID bus controller: HighPoint Technologies, Inc. RocketRAID 640 4 Port SATA-III Controller (rev 01)
        Subsystem: HighPoint Technologies, Inc. RocketRAID 640 4 Port SATA-III Controller
        Flags: bus master, fast devsel, latency 0, IRQ 17
        I/O ports at d090 [size=8]
        I/O ports at d080 [size=4]
        I/O ports at d070 [size=8]
        I/O ports at d060 [size=4]
        I/O ports at d050 [size=16]
        Memory at f7021000 (32-bit, non-prefetchable) [size=2K]
        Expansion ROM at f7010000 [disabled] [size=64K]
        Capabilities: [40] Power Management version 3
        Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit-
        Capabilities: [70] Express Legacy Endpoint, MSI 00

06:00.1 IDE interface: Marvell Technology Group Ltd. 88SE912x IDE Controller (rev 11) (prog-if 8f [Master SecP SecO PriP PriO])
        Subsystem: Marvell Technology Group Ltd. 88SE912x IDE Controller
        Flags: bus master, fast devsel, latency 0, IRQ 18
        I/O ports at d040 [size=8]
        I/O ports at d030 [size=4]
        I/O ports at d020 [size=8]
        I/O ports at d010 [size=4]
        I/O ports at d000 [size=16]
        Memory at f7020000 (32-bit, non-prefetchable) [size=16]
        Expansion ROM at f7000000 [disabled] [size=64K]
        Capabilities: [40] Power Management version 3
        Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit-
        Capabilities: [70] Express Legacy Endpoint, MSI 00
        Kernel driver in use: pata_marvell
        Kernel modules: pata_marvell, pata_acpi, ata_generic


Oh, my kernel is gentoo-sources 4.4.26, compiled via genkernel.

thanks in advance.
_________________
nasci pelado, careca e sem dente, o que vier é lucro


Last edited by esperto on Sat Jan 07, 2017 3:45 pm; edited 1 time in total
Back to top
View user's profile Send private message
NeddySeagoon
Administrator
Administrator


Joined: 05 Jul 2003
Posts: 43591
Location: 56N 3W

PostPosted: Mon Jan 02, 2017 6:10 pm    Post subject: Reply with quote

esperto,

Code:
[ 1676.028664]rr64x: disagrees about version of symbol module_layout


The kernel symbol called module_layout differs between your running kernel and the rr64x module you just loaded.

Code:
[ 1876.077527]rr64x: module verification failed: signature and/or required key missing - tainting kernel

Also, the module is not signed ad your kernel expects it to be.

You need to fix module_layout but it looks like you have unsigned modules set to be only a warning, so loading went ahead anyway.

Rebuild your kernel and the rr64x module, starting with make clean.
This will ensure that there are no old binaries lying around for make to reuse.
_________________
Regards,

NeddySeagoon

Computer users fall into two groups:-
those that do backups
those that have never had a hard drive fail.
Back to top
View user's profile Send private message
esperto
Apprentice
Apprentice


Joined: 27 Dec 2004
Posts: 158
Location: Brazil

PostPosted: Mon Jan 02, 2017 9:34 pm    Post subject: Reply with quote

NeddySeagoon,

Thanks for the quick answer!
as I had to recompile the kernel, I decided to update it, since the new 4.4.39 is out.

After recompiling the kernel and rr64x module, I don't see the signature verification error anymore (removed the requirement for signature with menuconfig), but I still get the "rr64x: disagrees about version of symbol module_layout"

I`m sure that the module is compiling against the correct kernel source, because I recompiled virtualbox-modules at the same time (emerge rr64x virtualbox-modules) and virtualbox modules are loading fine.

Any suggestions?
_________________
nasci pelado, careca e sem dente, o que vier é lucro
Back to top
View user's profile Send private message
esperto
Apprentice
Apprentice


Joined: 27 Dec 2004
Posts: 158
Location: Brazil

PostPosted: Sat Jan 07, 2017 3:44 pm    Post subject: Reply with quote

So after some more tests I solved it, the "symbol modul_layout" apparently vanished after disabling ccache feature, and the main problem was actually "DMAR: DRHD: handling fault status reg 2 ", which was caused by the driver trying to access a protected memory address, and disabling intel_iommu on boot (added intel_iommu=off to grub.cfg) the message went away and the card found the hard drive plugged in

Code:

[ 1520.604386] rr64x: module license 'Proprietary' taints kernel.
[ 1520.604399] Disabling lock debugging due to kernel taint
[ 1520.605476] rr64x:RocketRAID 64x SATA controller driver v1.1 
[ 1520.734179] rr64x:adapter at PCI 5:0:0, IRQ 17
[ 1520.745666] rr64x:adapter at PCI 6:0:0, IRQ 17
[ 1520.747406] rr64x:[0 0  ] start port.
[ 1520.747407] rr64x:[0 0  ] start port hard reset (probe 1).
[ 1520.947447] rr64x:[0 1  ] start port.
[ 1520.947449] rr64x:[0 1  ] start port hard reset (probe 1).
[ 1521.147493] rr64x:[1 0  ] start port.
[ 1521.147495] rr64x:[1 0  ] start port hard reset (probe 1).
[ 1521.347537] rr64x:[1 1  ] start port.
[ 1521.347540] rr64x:[1 1  ] start port hard reset (probe 1).
[ 1523.922222] rr64x:[0 0  ] start port soft reset (probe 1).
[ 1524.574876] rr64x:[0 1  ] failed to hard reset.
[ 1524.574885] rr64x:[0 1  ] failed to perform port hard reset.
[ 1524.754306] rr64x:[0 0  ] port started successfully.
[ 1524.754315] rr64x:[0 0 0] device probed successfully.
[ 1524.804298] rr64x:[1 0  ] failed to hard reset.
[ 1524.804309] rr64x:[1 0  ] failed to perform port hard reset.
[ 1525.005272] rr64x:[1 1  ] failed to hard reset.
[ 1525.005290] rr64x:[1 1  ] failed to perform port hard reset.
[ 1525.005672] scsi host10: rr64x
[ 1525.007288] scsi 10:0:0:0: Direct-Access     ATA      ST3200822AS      3.01 PQ: 0 ANSI: 5
[ 1525.014694] sd 10:0:0:0: Attached scsi generic sg1 type 0
[ 1525.014821] sd 10:0:0:0: [sdb] 390719855 512-byte logical blocks: (200 GB/186 GiB)
[ 1525.014854] sd 10:0:0:0: [sdb] Write Protect is off
[ 1525.014860] sd 10:0:0:0: [sdb] Mode Sense: 2f 00 00 00
[ 1525.014882] sd 10:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 1525.016592]  sdb: sdb1 sdb2 sdb3 sdb4
[ 1525.017401] sd 10:0:0:0: [sdb] Attached SCSI disk

_________________
nasci pelado, careca e sem dente, o que vier é lucro
Back to top
View user's profile Send private message
Display posts from previous:   
Reply to topic    Gentoo Forums Forum Index Kernel & Hardware All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum