Gentoo Forums
Gentoo Forums
Gentoo Forums
Quick Search: in
[SOVED] TP-LINK TL-WN851ND only on 2,4 Ghz with 20Mhz
View unanswered posts
View posts from last 24 hours

 
Reply to topic    Gentoo Forums Forum Index Networking & Security
View previous topic :: View next topic  
Author Message
Tux12Fun
Apprentice
Apprentice


Joined: 16 Aug 2007
Posts: 156

PostPosted: Mon Sep 19, 2016 8:02 pm    Post subject: [SOVED] TP-LINK TL-WN851ND only on 2,4 Ghz with 20Mhz Reply with quote

Hi,

i bought a TP Link WiFi Card, but I can only use 2,4 Ghz with 20Mhz.

Is there anything missing that is causing the card to only operate on this settings?

I would like to use the N 300MBit. (Card should support 5Ghz or?)

Any hint is welcome.

Card: https://www.conrad.de/de/wlan-steckkarte-pci-300-mbits-tp-link-tl-wn851nd-995241.html

Code:

lspci -vvv
06:01.0 Network controller: Qualcomm Atheros AR9227 Wireless Network Adapter (rev 01)
        Subsystem: Qualcomm Atheros AR9227 Wireless Network Adapter
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 168, Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 18
        Region 0: Memory at f7200000 (32-bit, non-prefetchable) [size=64K]
        Capabilities: [40] #80 [0000]
        Kernel driver in use: ath9k


Code:

Kenel Part

uname -a
Linux rechner1 4.0.4-gentoo #7 SMP Sat Jul 9 12:39:27 CEST 2016 x86_64 Intel(R) Core(TM) i5-3570K CPU @ 3.40GHz GenuineIntel GNU/Linux

.config

CONFIG_WLAN=y
# CONFIG_MAC80211_HWSIM is not set
# CONFIG_MWL8K is not set
CONFIG_ATH_COMMON=y
CONFIG_ATH_CARDS=y
# CONFIG_ATH_DEBUG is not set
# CONFIG_ATH5K is not set
# CONFIG_ATH5K_PCI is not set
CONFIG_ATH9K_HW=y
CONFIG_ATH9K_COMMON=y
CONFIG_ATH9K_BTCOEX_SUPPORT=y
CONFIG_ATH9K=y
CONFIG_ATH9K_PCI=y
CONFIG_ATH9K_AHB=y
# CONFIG_ATH9K_DEBUGFS is not set
# CONFIG_ATH9K_DYNACK is not set
# CONFIG_ATH9K_WOW is not set
CONFIG_ATH9K_RFKILL=y
CONFIG_ATH9K_CHANNEL_CONTEXT=y
CONFIG_ATH9K_PCOEM=y
# CONFIG_ATH9K_HTC is not set



Peering Partner is a "FritzBox 7390"
Displaying:
PC-Linux-192-168-0-21 192.168.0.21 A4:2B:B0:A6:5A:2B 30 / 50(Datarate MBs) 2,4 GHz / n / 20 MHz WPA2, 2 x 2


Code:

iwlist scan

wlp6s1    Scan completed :
          Cell 01 - Address: 60:E3:27:E2:AD:FE
                    Channel:1
                    Frequency:2.412 GHz (Channel 1)
                    Quality=31/70  Signal level=-79 dBm 
                    Encryption key:on
                    ESSID:"TP-LINK_E2ADFE"
                    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
                              9 Mb/s; 12 Mb/s; 18 Mb/s
                    Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s
                    Mode:Master
                    Extra:tsf=000001d7fa39bfef
                    Extra: Last beacon: 57ms ago
                    IE: Unknown: 000E54502D4C494E4B5F453241444645
                    IE: Unknown: 010882848B960C121824
                    IE: Unknown: 030101
                    IE: Unknown: 2A0100
                    IE: Unknown: 32043048606C
                    IE: Unknown: 2D1A6E101EFFFF000000000000000000000000000000000000000000
                    IE: Unknown: 3D1601050000000000000000000000000000000000000000
                    IE: WPA Version 1
                        Group Cipher : TKIP
                        Pairwise Ciphers (2) : TKIP CCMP
                        Authentication Suites (1) : PSK
                    IE: IEEE 802.11i/WPA2 Version 1
                        Group Cipher : TKIP
                        Pairwise Ciphers (2) : TKIP CCMP
                        Authentication Suites (1) : PSK
                    IE: Unknown: DD180050F2020101000003A4000027A4000042435E0062322F00
                    IE: Unknown: DD1E00904C336E101EFFFF000000000000000000000000000000000000000000
                    IE: Unknown: DD1A00904C3401050000000000000000000000000000000000000000
                    IE: Unknown: DD0600E04C0201E0
          Cell 02 - Address: 24:65:11:73:9A:06
                    Channel:1
                    Frequency:2.412 GHz (Channel 1)
                    Quality=32/70  Signal level=-78 dBm 
                    Encryption key:on
                    ESSID:"j3usjsi3lu345s56-2.4G"                                       <<< My Network #1 (j3usjsi3lu345s56-5G) is missing ???
                    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
                              9 Mb/s; 12 Mb/s; 18 Mb/s
                    Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s
                    Mode:Master
                    Extra:tsf=0000000000156319
                    Extra: Last beacon: 57ms ago
                    IE: Unknown: 00156A3375736A7369336C753334357335362D322E3447
                    IE: Unknown: 010882848B960C121824
                    IE: Unknown: 030101
                    IE: Unknown: 0706444520010D14
                    IE: Unknown: 2A0102
                    IE: Unknown: 32043048606C
                    IE: Unknown: 2D1A8C011BFFFF000000000000000000000100000000000000000000
                    IE: Unknown: 3D1601000500000000000000000000000000000000000000
                    IE: Unknown: 7F080000000000000040
                    IE: Unknown: DD180050F2020101000003A4000027A4000042435E0062322F00
                    IE: Unknown: DD0900037F01010000FF7F
                    IE: Unknown: DD0C00040E010102010000000000
                    IE: IEEE 802.11i/WPA2 Version 1
                        Group Cipher : TKIP
                        Pairwise Ciphers (1) : CCMP
                        Authentication Suites (1) : PSK
                    IE: WPA Version 1
                        Group Cipher : TKIP
                        Pairwise Ciphers (1) : TKIP
                        Authentication Suites (1) : PSK
          Cell 03 - Address: E8:94:F6:52:61:32
                    Channel:7
                    Frequency:2.442 GHz (Channel 7)
                    Quality=41/70  Signal level=-69 dBm 
                    Encryption key:on
                    ESSID:"TP-LINK"
                    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
                              9 Mb/s; 12 Mb/s; 18 Mb/s
                    Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s
                    Mode:Master
                    Extra:tsf=00000007616ff6f3
                    Extra: Last beacon: 57ms ago
                    IE: Unknown: 000754502D4C494E4B
                    IE: Unknown: 010882848B960C121824
                    IE: Unknown: 030107
                    IE: Unknown: 2A0102
                    IE: IEEE 802.11i/WPA2 Version 1
                        Group Cipher : CCMP
                        Pairwise Ciphers (1) : CCMP
                        Authentication Suites (1) : PSK
                    IE: Unknown: 32043048606C
                    IE: Unknown: 2D1AEF111BFFFF000000000000000000008000000000000000000000
                    IE: Unknown: 331AEF111BFFFF000000000000000000008000000000000000000000
                    IE: Unknown: 3D1607070500000000000000000000000000000000000000
                    IE: Unknown: 341607070500000000000000000000000000000000000000
                    IE: Unknown: DD180050F2020101840003A4000027A4000042435E0062322F00
                    IE: Unknown: DD0900037F01010000FF7F
                    IE: Unknown: DD990050F204104A0001101044000102103B00010310470010000102030405060708090A0B0C0D0E0F1021000754502D4C494E4B10\
                                           230009544C2D57523834314E10240003392E3010420003312E301054000800060050F204000110110019576972656C65737320526F75\
                                           74657220544C2D57523834314E100800020086103C000101104900140024E26002000101600000020001600100020001
          Cell 04 - Address: A0:F3:C1:05:65:F6
                    Channel:3
                    Frequency:2.422 GHz (Channel 3)
                    Quality=27/70  Signal level=-83 dBm 
                    Encryption key:on
                    ESSID:"TP-LINK_0565F6"
                    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
                              9 Mb/s; 12 Mb/s; 18 Mb/s
                    Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s
                    Mode:Master
                    Extra:tsf=00000f740d50a145
                    Extra: Last beacon: 57ms ago
                    IE: Unknown: 000E54502D4C494E4B5F303536354636
                    IE: Unknown: 010882848B960C121824
                    IE: Unknown: 030103
                    IE: Unknown: 2A0100
                    IE: IEEE 802.11i/WPA2 Version 1
                        Group Cipher : CCMP
                        Pairwise Ciphers (1) : CCMP
                        Authentication Suites (1) : PSK
                    IE: Unknown: 32043048606C
                    IE: Unknown: 2D1AEF1103FFFF0000000000000000000000000000000406E6E70D00
                    IE: Unknown: 331AEF1103FFFF0000000000000000000000000000000406E6E70D00
                    IE: Unknown: 3D1603051300000000000000000000000000000000000000
                    IE: Unknown: 341603051300000000000000000000000000000000000000
                    IE: Unknown: DD180050F2020101830003A4000027A4000042435E0062322F00
                    IE: Unknown: DD0900037F01010000FF7F
                    IE: Unknown: DD990050F204104A0001101044000102103B00010310470010000102030405060708090A0B0C0D0E0F1021000754502D4C494E4B10230009544C\
                                           2D57523834314E10240003382E3010420003312E301054000800060050F204000110110019576972656C65737320526F7574657220544C2D575238\
                                           34314E100800020086103C000101104900140024E26002000101600000020001600100020001




Line breaks added by NeddySeagoon


Last edited by Tux12Fun on Sat Sep 24, 2016 9:23 pm; edited 1 time in total
Back to top
View user's profile Send private message
Tux12Fun
Apprentice
Apprentice


Joined: 16 Aug 2007
Posts: 156

PostPosted: Mon Sep 19, 2016 8:07 pm    Post subject: Reply with quote

Oh I've seen 2,4 Ghz only.

But 300 Mbit should be possible
Back to top
View user's profile Send private message
Ant P.
Watchman
Watchman


Joined: 18 Apr 2009
Posts: 5919

PostPosted: Mon Sep 19, 2016 10:38 pm    Post subject: Reply with quote

That product page you linked says your card only supports 2.4GHz. Even so, it should be connecting at high speed automatically.

Can you install net-wireless/iw and post the output of `iw phy0 info` and `iw wlp6s1 info`? The older wireless-tools don't know about 802.11n.
Back to top
View user's profile Send private message
Tux12Fun
Apprentice
Apprentice


Joined: 16 Aug 2007
Posts: 156

PostPosted: Tue Sep 20, 2016 6:29 am    Post subject: Reply with quote

Thank you for your reply.

Yesterday I updated the kernel. But no change. Micro$$$ tells me that the Card is operating wit 150Mbit. :(

Here is the output:
Code:

Wiphy phy0
        max # scan SSIDs: 4
        max scan IEs length: 2257 bytes
        max # sched scan SSIDs: 0
        max # match sets: 0
        max # scan plans: 1
        max scan plan interval: -1
        max scan plan iterations: 0
        Retry short limit: 7
        Retry long limit: 4
        Coverage class: 0 (up to 0m)
        Device supports RSN-IBSS.
        Device supports AP-side u-APSD.
        Device supports T-DLS.
        Supported Ciphers:
                * WEP40 (00-0f-ac:1)
                * WEP104 (00-0f-ac:5)
                * TKIP (00-0f-ac:2)
                * CCMP (00-0f-ac:4)
                * 00-0f-ac:10
                * GCMP (00-0f-ac:8)
                * 00-0f-ac:9
                * CMAC (00-0f-ac:6)
                * 00-0f-ac:13
                * 00-0f-ac:11
                * 00-0f-ac:12
        Available Antennas: TX 0x3 RX 0x3
        Configured Antennas: TX 0x3 RX 0x3
        Supported interface modes:
                 * IBSS
                 * managed
                 * AP
                 * AP/VLAN
                 * WDS
                 * monitor
                 * P2P-client
                 * P2P-GO
                 * outside context of a BSS
        Band 1:
                Capabilities: 0x11ee
                        HT20/HT40
                        SM Power Save disabled
                        RX HT20 SGI
                        RX HT40 SGI
                        TX STBC
                        RX STBC 1-stream
                        Max AMSDU length: 3839 bytes
                        DSSS/CCK HT40
                Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
                Minimum RX AMPDU time spacing: 8 usec (0x06)
                HT TX/RX MCS rate indexes supported: 0-15
                Bitrates (non-HT):
                        * 1.0 Mbps
                        * 2.0 Mbps (short preamble supported)
                        * 5.5 Mbps (short preamble supported)
                        * 11.0 Mbps (short preamble supported)
                        * 6.0 Mbps
                        * 9.0 Mbps
                        * 12.0 Mbps
                        * 18.0 Mbps
                        * 24.0 Mbps
                        * 36.0 Mbps
                        * 48.0 Mbps
                        * 54.0 Mbps
                Frequencies:
                        * 2412 MHz [1] (20.0 dBm)
                        * 2417 MHz [2] (20.0 dBm)
                        * 2422 MHz [3] (20.0 dBm)
                        * 2427 MHz [4] (20.0 dBm)
                        * 2432 MHz [5] (20.0 dBm)
                        * 2437 MHz [6] (20.0 dBm)
                        * 2442 MHz [7] (20.0 dBm)
                        * 2447 MHz [8] (20.0 dBm)
                        * 2452 MHz [9] (20.0 dBm)
                        * 2457 MHz [10] (20.0 dBm)
                        * 2462 MHz [11] (20.0 dBm)
                        * 2467 MHz [12] (20.0 dBm)
                        * 2472 MHz [13] (20.0 dBm)
                        * 2484 MHz [14] (disabled)
        Supported commands:
                 * new_interface
                 * set_interface
                 * new_key
                 * start_ap
                 * new_station
                 * set_bss
                 * authenticate
                 * associate
                 * deauthenticate
                 * disassociate
                 * join_ibss
                 * remain_on_channel
                 * set_tx_bitrate_mask
                 * frame
                 * frame_wait_cancel
                 * set_wiphy_netns
                 * set_channel
                 * set_wds_peer
                 * tdls_mgmt
                 * tdls_oper
                 * probe_client
                 * set_noack_map
                 * register_beacons
                 * start_p2p_device
                 * set_mcast_rate
                 * channel_switch
                 * set_qos_map
                 * connect
                 * disconnect
        Supported TX frame types:
                 * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
                 * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
                 * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
                 * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
                 * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
                 * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
                 * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
                 * P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
        Supported RX frame types:
                 * IBSS: 0x40 0xb0 0xc0 0xd0
                 * managed: 0x40 0xd0
                 * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
                 * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
                 * mesh point: 0xb0 0xc0 0xd0
                 * P2P-client: 0x40 0xd0
                 * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
                 * P2P-device: 0x40 0xd0
        software interface modes (can always be added):
                 * AP/VLAN
                 * monitor
        valid interface combinations:
                 * #{ managed } <= 2048, #{ AP } <= 8, #{ P2P-client, P2P-GO } <= 1,
                   total <= 2048, #channels <= 1, STA/AP BI must match
                 * #{ WDS } <= 2048,
                   total <= 2048, #channels <= 1, STA/AP BI must match
        HT Capability overrides:
                 * MCS: ff ff ff ff ff ff ff ff ff ff
                 * maximum A-MSDU length
                 * supported channel width
                 * short GI for 40 MHz
                 * max A-MPDU length exponent
                 * min MPDU start spacing
        Device supports TX status socket option.
        Device supports HT-IBSS.
        Device supports SAE with AUTHENTICATE command
        Device supports low priority scan.
        Device supports scan flush.
        Device supports AP scan.
        Device supports per-vif TX power setting
        P2P GO supports CT window setting
        Driver supports full state transitions for AP/GO clients
        Driver supports a userspace MPM
        Device supports active monitor (which will ACK incoming frames)
        Driver/device bandwidth changes during BSS lifetime (AP/GO mode)
        Device supports configuring vdev MAC-addr on create.


Code:

iwconfig
wlan1     IEEE 802.11  ESSID:off/any 
          Mode:Managed  Access Point: Not-Associated   Tx-Power=0 dBm   
          Retry short limit:7   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:on
         
wlp6s1    IEEE 802.11  ESSID:"j3usjsi3lu345s56-2.4G" 
          Mode:Managed  Frequency:2.412 GHz  Access Point: 24:65:11:73:9A:06   
          Bit Rate=6.5 Mb/s   Tx-Power=19 dBm   
          Retry short limit:7   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
          Link Quality=44/70  Signal level=-66 dBm 
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:1  Invalid misc:437   Missed beacon:0

enp4s0    no wireless extensions.

wlan2     IEEE 802.11  ESSID:off/any 
          Mode:Managed  Access Point: Not-Associated   Tx-Power=0 dBm   
          Retry short limit:7   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:on
         
lo        no wireless extensions.

hwsim0    no wireless extensions.



Code:

rechner1 thomas # iw wlp6s1 info
Interface wlp6s1
        ifindex 3
        wdev 0x1
        addr a4:2b:b0:a6:5a:2b
        ssid j3usjsi3lu345s56-2.4G
        type managed
        wiphy 0
        channel 1 (2412 MHz), width: 20 MHz, center1: 2412 MHz
        txpower 19.00 dBm
rechner1 thomas # iw wlan1 info
Interface wlan1
        ifindex 4
        wdev 0x100000001
        addr 02:00:00:00:00:00
        type managed
        wiphy 1
        txpower 0.00 dBm
rechner1 thomas # iw wlan2 info
Interface wlan2
        ifindex 5
        wdev 0x200000001
        addr 02:00:00:00:01:00
        type managed
        wiphy 2
        txpower 0.00 dBm
rechner1 thomas # iw hwsim0 info
command failed: No such device (-19)



Code:

06:01.0 Network controller: Qualcomm Atheros AR9227 Wireless Network Adapter (rev 01)
        Subsystem: Qualcomm Atheros AR9227 Wireless Network Adapter
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 168, Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 18
        Region 0: Memory at f7200000 (32-bit, non-prefetchable) [size=64K]
        Capabilities: [40] #80 [0000]
        Kernel driver in use: ath9k



Code:

CONFIG_WLAN=y
CONFIG_WLAN_VENDOR_ADMTEK=y
# CONFIG_ADM8211 is not set
CONFIG_ATH_COMMON=y
CONFIG_WLAN_VENDOR_ATH=y
# CONFIG_ATH_DEBUG is not set
# CONFIG_ATH5K is not set
# CONFIG_ATH5K_PCI is not set
CONFIG_ATH9K_HW=y
CONFIG_ATH9K_COMMON=y
CONFIG_ATH9K_BTCOEX_SUPPORT=y
CONFIG_ATH9K=y
CONFIG_ATH9K_PCI=y
CONFIG_ATH9K_AHB=y
# CONFIG_ATH9K_DEBUGFS is not set
# CONFIG_ATH9K_DYNACK is not set
# CONFIG_ATH9K_WOW is not set
CONFIG_ATH9K_RFKILL=y
CONFIG_ATH9K_CHANNEL_CONTEXT=y
CONFIG_ATH9K_PCOEM=y
CONFIG_ATH9K_HTC=y
# CONFIG_ATH9K_HTC_DEBUGFS is not set
CONFIG_ATH9K_HWRNG=y
# CONFIG_CARL9170 is not set
# CONFIG_ATH6KL is not set
# CONFIG_AR5523 is not set
# CONFIG_WIL6210 is not set
# CONFIG_ATH10K is not set
# CONFIG_WCN36XX is not set
Back to top
View user's profile Send private message
NeddySeagoon
Administrator
Administrator


Joined: 05 Jul 2003
Posts: 43765
Location: 56N 3W

PostPosted: Tue Sep 20, 2016 7:10 am    Post subject: Reply with quote

Tux12Fun,

Please check your dmesg for something like
Code:
20/40 MHz operation not permitted on channel pri=1 sec=5 based on overlapping BSSes


The spread spectrum on the 2.4GHz band means that each WiFi link is actually 5 channels wide, centred on the channel you are on
Your channel 7 actually uses channel 4.5 to channel 9.5.
This also means that there are really only 3 channels in the 2.4G band. Channels 1, 6 and 11

N operation may need two non overlapping channels and your iwlist scan shows channels 1, 3 and 7 in use already (+/- 2.5 channels)
The only free non overlapping channel you could have is channel 12 and that may not be permitted in your region.

You could try disabling auto scanning if you nave it enabled and see if you can force N mode that way.
_________________
Regards,

NeddySeagoon

Computer users fall into two groups:-
those that do backups
those that have never had a hard drive fail.
Back to top
View user's profile Send private message
Tux12Fun
Apprentice
Apprentice


Joined: 16 Aug 2007
Posts: 156

PostPosted: Tue Sep 20, 2016 7:27 pm    Post subject: Reply with quote

I can't see this message in dmesg.

I reconnected with wicd and this this the dmesg output

Code:

[   33.233829] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: (null)
[   42.149114] EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: (null)
[   43.142404] nvidia-modeset: Allocated GPU:0 (GPU-15e389d2-59d6-d296-671a-966b15538ab6) @ PCI:0000:01:00.0
[   46.963131] nvidia-uvm: Loaded the UVM driver in 8 mode, major device number 245
[  120.090417] wlp6s1: authenticate with 24:65:11:73:9a:06
[  120.112543] wlp6s1: send auth to 24:65:11:73:9a:06 (try 1/3)
[  120.120380] wlp6s1: authenticated
[  120.121107] wlp6s1: associate with 24:65:11:73:9a:06 (try 1/3)
[  120.132527] wlp6s1: RX AssocResp from 24:65:11:73:9a:06 (capab=0x431 status=0 aid=2)
[  120.132672] wlp6s1: associated
[47340.733526] wlp6s1: deauthenticating from 24:65:11:73:9a:06 by local choice (Reason: 3=DEAUTH_LEAVING)
[47348.988038] wlp6s1: authenticate with 24:65:11:73:9a:06
[47349.010082] wlp6s1: send auth to 24:65:11:73:9a:06 (try 1/3)
[47349.017641] wlp6s1: authenticated
[47349.017689] wlp6s1: associate with 24:65:11:73:9a:06 (try 1/3)
[47349.030770] wlp6s1: RX AssocResp from 24:65:11:73:9a:06 (capab=0x31 status=0 aid=2)
[47349.030887] wlp6s1: associated
rechner1 linux # dmesg | grep -i 'not permitted'
rechner1 linux #
Back to top
View user's profile Send private message
Tux12Fun
Apprentice
Apprentice


Joined: 16 Aug 2007
Posts: 156

PostPosted: Sat Sep 24, 2016 9:23 pm    Post subject: Reply with quote

I Changed to a 5Ghz Card an the Problem is gone.
Back to top
View user's profile Send private message
Display posts from previous:   
Reply to topic    Gentoo Forums Forum Index Networking & Security All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum