| View previous topic :: View next topic |
| Author |
Message |
Tux12Fun
Apprentice
Joined: 16 Aug 2007
Posts: 156
|
 Posted: Mon Sep 19, 2016 8:02 pm Post subject: [SOVED] TP-LINK TL-WN851ND only on 2,4 Ghz with 20Mhz |
 |
|
Hi,
i bought a TP Link WiFi Card, but I can only use 2,4 Ghz with 20Mhz.
Is there anything missing that is causing the card to only operate on this settings?
I would like to use the N 300MBit. (Card should support 5Ghz or?)
Any hint is welcome.
Card: https://www.conrad.de/de/wlan-steckkarte-pci-300-mbits-tp-link-tl-wn851nd-995241.html
| Code: |
lspci -vvv
06:01.0 Network controller: Qualcomm Atheros AR9227 Wireless Network Adapter (rev 01)
Subsystem: Qualcomm Atheros AR9227 Wireless Network Adapter
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at f7200000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [40] #80 [0000]
Kernel driver in use: ath9k
|
| Code: |
Kenel Part
uname -a
Linux rechner1 4.0.4-gentoo #7 SMP Sat Jul 9 12:39:27 CEST 2016 x86_64 Intel(R) Core(TM) i5-3570K CPU @ 3.40GHz GenuineIntel GNU/Linux
.config
CONFIG_WLAN=y
# CONFIG_MAC80211_HWSIM is not set
# CONFIG_MWL8K is not set
CONFIG_ATH_COMMON=y
CONFIG_ATH_CARDS=y
# CONFIG_ATH_DEBUG is not set
# CONFIG_ATH5K is not set
# CONFIG_ATH5K_PCI is not set
CONFIG_ATH9K_HW=y
CONFIG_ATH9K_COMMON=y
CONFIG_ATH9K_BTCOEX_SUPPORT=y
CONFIG_ATH9K=y
CONFIG_ATH9K_PCI=y
CONFIG_ATH9K_AHB=y
# CONFIG_ATH9K_DEBUGFS is not set
# CONFIG_ATH9K_DYNACK is not set
# CONFIG_ATH9K_WOW is not set
CONFIG_ATH9K_RFKILL=y
CONFIG_ATH9K_CHANNEL_CONTEXT=y
CONFIG_ATH9K_PCOEM=y
# CONFIG_ATH9K_HTC is not set
|
Peering Partner is a "FritzBox 7390"
Displaying:
PC-Linux-192-168-0-21 192.168.0.21 A4:2B:B0:A6:5A:2B 30 / 50(Datarate MBs) 2,4 GHz / n / 20 MHz WPA2, 2 x 2
| Code: |
iwlist scan
wlp6s1 Scan completed :
Cell 01 - Address: 60:E3:27:E2:AD:FE
Channel:1
Frequency:2.412 GHz (Channel 1)
Quality=31/70 Signal level=-79 dBm
Encryption key:on
ESSID:"TP-LINK_E2ADFE"
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
9 Mb/s; 12 Mb/s; 18 Mb/s
Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s
Mode:Master
Extra:tsf=000001d7fa39bfef
Extra: Last beacon: 57ms ago
IE: Unknown: 000E54502D4C494E4B5F453241444645
IE: Unknown: 010882848B960C121824
IE: Unknown: 030101
IE: Unknown: 2A0100
IE: Unknown: 32043048606C
IE: Unknown: 2D1A6E101EFFFF000000000000000000000000000000000000000000
IE: Unknown: 3D1601050000000000000000000000000000000000000000
IE: WPA Version 1
Group Cipher : TKIP
Pairwise Ciphers (2) : TKIP CCMP
Authentication Suites (1) : PSK
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : TKIP
Pairwise Ciphers (2) : TKIP CCMP
Authentication Suites (1) : PSK
IE: Unknown: DD180050F2020101000003A4000027A4000042435E0062322F00
IE: Unknown: DD1E00904C336E101EFFFF000000000000000000000000000000000000000000
IE: Unknown: DD1A00904C3401050000000000000000000000000000000000000000
IE: Unknown: DD0600E04C0201E0
Cell 02 - Address: 24:65:11:73:9A:06
Channel:1
Frequency:2.412 GHz (Channel 1)
Quality=32/70 Signal level=-78 dBm
Encryption key:on
ESSID:"j3usjsi3lu345s56-2.4G" <<< My Network #1 (j3usjsi3lu345s56-5G) is missing ???
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
9 Mb/s; 12 Mb/s; 18 Mb/s
Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s
Mode:Master
Extra:tsf=0000000000156319
Extra: Last beacon: 57ms ago
IE: Unknown: 00156A3375736A7369336C753334357335362D322E3447
IE: Unknown: 010882848B960C121824
IE: Unknown: 030101
IE: Unknown: 0706444520010D14
IE: Unknown: 2A0102
IE: Unknown: 32043048606C
IE: Unknown: 2D1A8C011BFFFF000000000000000000000100000000000000000000
IE: Unknown: 3D1601000500000000000000000000000000000000000000
IE: Unknown: 7F080000000000000040
IE: Unknown: DD180050F2020101000003A4000027A4000042435E0062322F00
IE: Unknown: DD0900037F01010000FF7F
IE: Unknown: DD0C00040E010102010000000000
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : PSK
IE: WPA Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : TKIP
Authentication Suites (1) : PSK
Cell 03 - Address: E8:94:F6:52:61:32
Channel:7
Frequency:2.442 GHz (Channel 7)
Quality=41/70 Signal level=-69 dBm
Encryption key:on
ESSID:"TP-LINK"
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
9 Mb/s; 12 Mb/s; 18 Mb/s
Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s
Mode:Master
Extra:tsf=00000007616ff6f3
Extra: Last beacon: 57ms ago
IE: Unknown: 000754502D4C494E4B
IE: Unknown: 010882848B960C121824
IE: Unknown: 030107
IE: Unknown: 2A0102
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : CCMP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : PSK
IE: Unknown: 32043048606C
IE: Unknown: 2D1AEF111BFFFF000000000000000000008000000000000000000000
IE: Unknown: 331AEF111BFFFF000000000000000000008000000000000000000000
IE: Unknown: 3D1607070500000000000000000000000000000000000000
IE: Unknown: 341607070500000000000000000000000000000000000000
IE: Unknown: DD180050F2020101840003A4000027A4000042435E0062322F00
IE: Unknown: DD0900037F01010000FF7F
IE: Unknown: DD990050F204104A0001101044000102103B00010310470010000102030405060708090A0B0C0D0E0F1021000754502D4C494E4B10\
230009544C2D57523834314E10240003392E3010420003312E301054000800060050F204000110110019576972656C65737320526F75\
74657220544C2D57523834314E100800020086103C000101104900140024E26002000101600000020001600100020001
Cell 04 - Address: A0:F3:C1:05:65:F6
Channel:3
Frequency:2.422 GHz (Channel 3)
Quality=27/70 Signal level=-83 dBm
Encryption key:on
ESSID:"TP-LINK_0565F6"
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
9 Mb/s; 12 Mb/s; 18 Mb/s
Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s
Mode:Master
Extra:tsf=00000f740d50a145
Extra: Last beacon: 57ms ago
IE: Unknown: 000E54502D4C494E4B5F303536354636
IE: Unknown: 010882848B960C121824
IE: Unknown: 030103
IE: Unknown: 2A0100
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : CCMP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : PSK
IE: Unknown: 32043048606C
IE: Unknown: 2D1AEF1103FFFF0000000000000000000000000000000406E6E70D00
IE: Unknown: 331AEF1103FFFF0000000000000000000000000000000406E6E70D00
IE: Unknown: 3D1603051300000000000000000000000000000000000000
IE: Unknown: 341603051300000000000000000000000000000000000000
IE: Unknown: DD180050F2020101830003A4000027A4000042435E0062322F00
IE: Unknown: DD0900037F01010000FF7F
IE: Unknown: DD990050F204104A0001101044000102103B00010310470010000102030405060708090A0B0C0D0E0F1021000754502D4C494E4B10230009544C\
2D57523834314E10240003382E3010420003312E301054000800060050F204000110110019576972656C65737320526F7574657220544C2D575238\
34314E100800020086103C000101104900140024E26002000101600000020001600100020001
|
Line breaks added by NeddySeagoon
Last edited by Tux12Fun on Sat Sep 24, 2016 9:23 pm; edited 1 time in total |
|
| Back to top |
|
 |
Tux12Fun
Apprentice
Joined: 16 Aug 2007
Posts: 156
|
| Posted: Mon Sep 19, 2016 8:07 pm Post subject: |
|
|
Oh I've seen 2,4 Ghz only.
But 300 Mbit should be possible |
|
| Back to top |
|
|
Ant P.
Watchman
Joined: 18 Apr 2009
Posts: 6920
|
| Posted: Mon Sep 19, 2016 10:38 pm Post subject: |
|
|
That product page you linked says your card only supports 2.4GHz. Even so, it should be connecting at high speed automatically.
Can you install net-wireless/iw and post the output of `iw phy0 info` and `iw wlp6s1 info`? The older wireless-tools don't know about 802.11n. |
|
| Back to top |
|
|
Tux12Fun
Apprentice
Joined: 16 Aug 2007
Posts: 156
|
| Posted: Tue Sep 20, 2016 6:29 am Post subject: |
|
|
Thank you for your reply.
Yesterday I updated the kernel. But no change. Micro$$$ tells me that the Card is operating wit 150Mbit. 
Here is the output:
| Code: |
Wiphy phy0
max # scan SSIDs: 4
max scan IEs length: 2257 bytes
max # sched scan SSIDs: 0
max # match sets: 0
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports RSN-IBSS.
Device supports AP-side u-APSD.
Device supports T-DLS.
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP (00-0f-ac:4)
* 00-0f-ac:10
* GCMP (00-0f-ac:8)
* 00-0f-ac:9
* CMAC (00-0f-ac:6)
* 00-0f-ac:13
* 00-0f-ac:11
* 00-0f-ac:12
Available Antennas: TX 0x3 RX 0x3
Configured Antennas: TX 0x3 RX 0x3
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* WDS
* monitor
* P2P-client
* P2P-GO
* outside context of a BSS
Band 1:
Capabilities: 0x11ee
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 3839 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-15
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps (short preamble supported)
* 5.5 Mbps (short preamble supported)
* 11.0 Mbps (short preamble supported)
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 2412 MHz [1] (20.0 dBm)
* 2417 MHz [2] (20.0 dBm)
* 2422 MHz [3] (20.0 dBm)
* 2427 MHz [4] (20.0 dBm)
* 2432 MHz [5] (20.0 dBm)
* 2437 MHz [6] (20.0 dBm)
* 2442 MHz [7] (20.0 dBm)
* 2447 MHz [8] (20.0 dBm)
* 2452 MHz [9] (20.0 dBm)
* 2457 MHz [10] (20.0 dBm)
* 2462 MHz [11] (20.0 dBm)
* 2467 MHz [12] (20.0 dBm)
* 2472 MHz [13] (20.0 dBm)
* 2484 MHz [14] (disabled)
Supported commands:
* new_interface
* set_interface
* new_key
* start_ap
* new_station
* set_bss
* authenticate
* associate
* deauthenticate
* disassociate
* join_ibss
* remain_on_channel
* set_tx_bitrate_mask
* frame
* frame_wait_cancel
* set_wiphy_netns
* set_channel
* set_wds_peer
* tdls_mgmt
* tdls_oper
* probe_client
* set_noack_map
* register_beacons
* start_p2p_device
* set_mcast_rate
* channel_switch
* set_qos_map
* connect
* disconnect
Supported TX frame types:
* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
* IBSS: 0x40 0xb0 0xc0 0xd0
* managed: 0x40 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* mesh point: 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* P2P-device: 0x40 0xd0
software interface modes (can always be added):
* AP/VLAN
* monitor
valid interface combinations:
* #{ managed } <= 2048, #{ AP } <= 8, #{ P2P-client, P2P-GO } <= 1,
total <= 2048, #channels <= 1, STA/AP BI must match
* #{ WDS } <= 2048,
total <= 2048, #channels <= 1, STA/AP BI must match
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
Device supports TX status socket option.
Device supports HT-IBSS.
Device supports SAE with AUTHENTICATE command
Device supports low priority scan.
Device supports scan flush.
Device supports AP scan.
Device supports per-vif TX power setting
P2P GO supports CT window setting
Driver supports full state transitions for AP/GO clients
Driver supports a userspace MPM
Device supports active monitor (which will ACK incoming frames)
Driver/device bandwidth changes during BSS lifetime (AP/GO mode)
Device supports configuring vdev MAC-addr on create.
|
| Code: |
iwconfig
wlan1 IEEE 802.11 ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm
Retry short limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:on
wlp6s1 IEEE 802.11 ESSID:"j3usjsi3lu345s56-2.4G"
Mode:Managed Frequency:2.412 GHz Access Point: 24:65:11:73:9A:06
Bit Rate=6.5 Mb/s Tx-Power=19 dBm
Retry short limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=44/70 Signal level=-66 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:1 Invalid misc:437 Missed beacon:0
enp4s0 no wireless extensions.
wlan2 IEEE 802.11 ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm
Retry short limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:on
lo no wireless extensions.
hwsim0 no wireless extensions.
|
| Code: |
rechner1 thomas # iw wlp6s1 info
Interface wlp6s1
ifindex 3
wdev 0x1
addr a4:2b:b0:a6:5a:2b
ssid j3usjsi3lu345s56-2.4G
type managed
wiphy 0
channel 1 (2412 MHz), width: 20 MHz, center1: 2412 MHz
txpower 19.00 dBm
rechner1 thomas # iw wlan1 info
Interface wlan1
ifindex 4
wdev 0x100000001
addr 02:00:00:00:00:00
type managed
wiphy 1
txpower 0.00 dBm
rechner1 thomas # iw wlan2 info
Interface wlan2
ifindex 5
wdev 0x200000001
addr 02:00:00:00:01:00
type managed
wiphy 2
txpower 0.00 dBm
rechner1 thomas # iw hwsim0 info
command failed: No such device (-19)
|
| Code: |
06:01.0 Network controller: Qualcomm Atheros AR9227 Wireless Network Adapter (rev 01)
Subsystem: Qualcomm Atheros AR9227 Wireless Network Adapter
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at f7200000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [40] #80 [0000]
Kernel driver in use: ath9k
|
| Code: |
CONFIG_WLAN=y
CONFIG_WLAN_VENDOR_ADMTEK=y
# CONFIG_ADM8211 is not set
CONFIG_ATH_COMMON=y
CONFIG_WLAN_VENDOR_ATH=y
# CONFIG_ATH_DEBUG is not set
# CONFIG_ATH5K is not set
# CONFIG_ATH5K_PCI is not set
CONFIG_ATH9K_HW=y
CONFIG_ATH9K_COMMON=y
CONFIG_ATH9K_BTCOEX_SUPPORT=y
CONFIG_ATH9K=y
CONFIG_ATH9K_PCI=y
CONFIG_ATH9K_AHB=y
# CONFIG_ATH9K_DEBUGFS is not set
# CONFIG_ATH9K_DYNACK is not set
# CONFIG_ATH9K_WOW is not set
CONFIG_ATH9K_RFKILL=y
CONFIG_ATH9K_CHANNEL_CONTEXT=y
CONFIG_ATH9K_PCOEM=y
CONFIG_ATH9K_HTC=y
# CONFIG_ATH9K_HTC_DEBUGFS is not set
CONFIG_ATH9K_HWRNG=y
# CONFIG_CARL9170 is not set
# CONFIG_ATH6KL is not set
# CONFIG_AR5523 is not set
# CONFIG_WIL6210 is not set
# CONFIG_ATH10K is not set
# CONFIG_WCN36XX is not set
|
|
|
| Back to top |
|
|
NeddySeagoon
Administrator
Joined: 05 Jul 2003
Posts: 54237
Location: 56N 3W
|
| Posted: Tue Sep 20, 2016 7:10 am Post subject: |
|
|
Tux12Fun,
Please check your dmesg for something like | Code: | | 20/40 MHz operation not permitted on channel pri=1 sec=5 based on overlapping BSSes |
The spread spectrum on the 2.4GHz band means that each WiFi link is actually 5 channels wide, centred on the channel you are on
Your channel 7 actually uses channel 4.5 to channel 9.5.
This also means that there are really only 3 channels in the 2.4G band. Channels 1, 6 and 11
N operation may need two non overlapping channels and your iwlist scan shows channels 1, 3 and 7 in use already (+/- 2.5 channels)
The only free non overlapping channel you could have is channel 12 and that may not be permitted in your region.
You could try disabling auto scanning if you nave it enabled and see if you can force N mode that way.
_________________
Regards,
NeddySeagoon
Computer users fall into two groups:-
those that do backups
those that have never had a hard drive fail. |
|
| Back to top |
|
|
Tux12Fun
Apprentice
Joined: 16 Aug 2007
Posts: 156
|
| Posted: Tue Sep 20, 2016 7:27 pm Post subject: |
|
|
I can't see this message in dmesg.
I reconnected with wicd and this this the dmesg output
| Code: |
[ 33.233829] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: (null)
[ 42.149114] EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: (null)
[ 43.142404] nvidia-modeset: Allocated GPU:0 (GPU-15e389d2-59d6-d296-671a-966b15538ab6) @ PCI:0000:01:00.0
[ 46.963131] nvidia-uvm: Loaded the UVM driver in 8 mode, major device number 245
[ 120.090417] wlp6s1: authenticate with 24:65:11:73:9a:06
[ 120.112543] wlp6s1: send auth to 24:65:11:73:9a:06 (try 1/3)
[ 120.120380] wlp6s1: authenticated
[ 120.121107] wlp6s1: associate with 24:65:11:73:9a:06 (try 1/3)
[ 120.132527] wlp6s1: RX AssocResp from 24:65:11:73:9a:06 (capab=0x431 status=0 aid=2)
[ 120.132672] wlp6s1: associated
[47340.733526] wlp6s1: deauthenticating from 24:65:11:73:9a:06 by local choice (Reason: 3=DEAUTH_LEAVING)
[47348.988038] wlp6s1: authenticate with 24:65:11:73:9a:06
[47349.010082] wlp6s1: send auth to 24:65:11:73:9a:06 (try 1/3)
[47349.017641] wlp6s1: authenticated
[47349.017689] wlp6s1: associate with 24:65:11:73:9a:06 (try 1/3)
[47349.030770] wlp6s1: RX AssocResp from 24:65:11:73:9a:06 (capab=0x31 status=0 aid=2)
[47349.030887] wlp6s1: associated
rechner1 linux # dmesg | grep -i 'not permitted'
rechner1 linux #
|
|
|
| Back to top |
|
|
Tux12Fun
Apprentice
Joined: 16 Aug 2007
Posts: 156
|
| Posted: Sat Sep 24, 2016 9:23 pm Post subject: |
|
|
| I Changed to a 5Ghz Card an the Problem is gone. |
|
| Back to top |
|
|
|
Networking & Security
