View previous topic :: View next topic |
Author |
Message |
moodsx n00b
Joined: 23 Jul 2016 Posts: 13
|
Posted: Sat Jul 23, 2016 12:23 am Post subject: [gelöst] wlan wpa_supplicant |
|
|
Hallo Leute,
habe ein Problem bei der config meines wlan-adapters.
Folgendes habe ich verbrochen:
/etc/conf.d/net:
Code: | modules="wpa_supplicant"
wpa_supplicant_wlp2s0="-Dath9k"
config_wlp2s0="dhcp"
|
/etc/wpa_supplicant/wpa_supplicant.conf
Code: | ctrl_interface=/var/run/wpa_supplicant
ctrl_interface_group=0
ap_scan=1
network={
ssid="my essid"
psk="my key"
proto=WPA
key_mgmt=WPA-PSK
group=CCMP TKIP
pairwise=CCMP TKIP
priority=1
}
|
Nach einem restart (/etc/init.d/net.wlp2s0 restart) erhalte ich das:
Code: | * Bringing up interface wlp2s0
* Starting wpa_supplicant on wlp2s0 ...
Successfully initialized wpa_supplicant
wlp2s0: Unsupported driver 'ath9k'
* start-stop-daemon: failed to start `/usr/sbin/wpa_supplicant' [ !! ]
* ERROR: net.wlp2s0 failed to start
|
lspci:
Code: | 02:00.0 Network controller: Qualcomm Atheros AR9485 Wireless Network Adapter (rev 01) |
Treiber: ath9k und ein:
spuckt mir auch alle verfügbaren wlans in der Umgebung aus.
Hat jemand einen Tipp für mich wo hier das Problem liegt?
Danke für Eure Hilfe.
MfG moodsx
Last edited by moodsx on Sat Jul 23, 2016 1:05 pm; edited 1 time in total |
|
Back to top |
|
|
Fijoldar Apprentice
Joined: 10 Apr 2013 Posts: 248
|
Posted: Sat Jul 23, 2016 8:14 am Post subject: |
|
|
Hallo moodsx,
diese Zeile hier würde ich mal weglassen:
Code: | wpa_supplicant_wlp2s0="-Dath9k" |
Funktioniert es dann? |
|
Back to top |
|
|
moodsx n00b
Joined: 23 Jul 2016 Posts: 13
|
Posted: Sat Jul 23, 2016 8:23 am Post subject: |
|
|
Nein, leider nicht. Ein restart nach dem entfernen der Zeile:
Code: | * Caching service dependencies ... [ ok ]
* Bringing up interface wlp2s0
* Starting wpa_supplicant on wlp2s0 ...
Successfully initialized wpa_supplicant
rfkill: WLAN soft blocked
rfkill: WLAN hard blocked [ ok ]
* Starting wpa_cli on wlp2s0 ... [ ok ]
* Backgrounding ... ...
* WARNING: net.wlp2s0 has started, but is inactive |
Ein iwconfig zeigt keinerlei config des adapters:
Code: | wlp2s0 IEEE 802.11bgn ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=off
Retry short limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
|
|
|
Back to top |
|
|
moodsx n00b
Joined: 23 Jul 2016 Posts: 13
|
Posted: Sat Jul 23, 2016 1:04 pm Post subject: |
|
|
Hat sich erledigt, lag an meiner Kernel config. Was genau, kein Schimmer, habe das ganze Untergedöhns vom Treibermodul mit genommen und nu läuft das Teil.
Danke an alle die versucht haben zu helfen. |
|
Back to top |
|
|
|