View previous topic :: View next topic |
Author |
Message |
sensi_tuX n00b
Joined: 18 Dec 2004 Posts: 46
|
Posted: Sat Mar 26, 2016 3:47 pm Post subject: Problems to configure wifi |
|
|
Hi guys,
im having some troubles configuring my wifi. Im having a Intel Centrino N-135 chipset and was following the howtos on
https://wiki.gentoo.org/wiki/Wifi and https://wiki.gentoo.org/wiki/Wpa_supplicant but still cant figure out what im missing/doing wrong.
I want to log in into my home wlan with wpa_gui but getting always the message "could not get status from wpa_supplicant". No matter if im starting with root or any other user. Its also no adapter and network shown what i could choose...
Output of my iwconfig:
Code: |
enp4s0f2 no wireless extensions.
lo no wireless extensions.
wlp3s0 IEEE 802.11bgn ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm
Retry short limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
|
wlp3s0 is the wifi device.
Code: |
tree /sys/class/net
/sys/class/net
├── enp4s0f2 -> ../../devices/pci0000:00/0000:00:1c.3/0000:04:00.2/net/enp4s0f2
├── lo -> ../../devices/virtual/net/lo
└── wlp3s0 -> ../../devices/pci0000:00/0000:00:1c.2/0000:03:00.0/net/wlp3s0
|
ifconfig -a
Code: |
enp4s0f2: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.0.12 netmask 255.255.255.0 broadcast 192.168.0.255
inet6 fe80::f46c:f97:7ddd:7479 prefixlen 64 scopeid 0x20<link>
inet6 2001:4d50:48d:9900:59cb:bf6c:350f:af9d prefixlen 64 scopeid 0x0<global>
inet6 2001:4d50:48d:9900:290:f5ff:fee0:3196 prefixlen 128 scopeid 0x0<global>
ether 00:90:f5:e0:32:96 txqueuelen 1000 (Ethernet)
RX packets 8004 bytes 5775679 (5.5 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 5901 bytes 761231 (743.3 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1 (Local Loopback)
RX packets 4 bytes 240 (240.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 4 bytes 240 (240.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
wlp3s0: flags=4098<BROADCAST,MULTICAST> mtu 1500
ether 0c:d2:92:48:7e:a7 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
|
lshw | grep -i driver
Code: |
configuration: driver=ivb_uncore
configuration: driver=pcieport
configuration: driver=i915 latency=0
configuration: driver=xhci_hcd latency=0
configuration: driver=ehci-pci latency=0
configuration: driver=snd_hda_intel latency=0
configuration: driver=pcieport
configuration: driver=pcieport
configuration: broadcast=yes driver=iwlwifi driverversion=4.5.0-gentoo firmware=18.168.6.1 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn
configuration: driver=pcieport
configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8411-1_0.0.3 06/18/12 ip=192.168.0.12 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s
configuration: driver=ehci-pci latency=0
configuration: driver=lpc_ich latency=0
configuration: driver=ahci latency=0
|
Code: |
ifconfig -v wlp3s0 up
|
==> No output...
less /etc/conf.d/net
Code: |
config_enp4s0f2="dhcp"
dhcpcd_enp4s0f2="-t 10"
modules_wlp3s0="wpa_supplicant"
config_wlp3s0="dhcp"
|
Any hints what im missing or doing wrong here? |
|
Back to top |
|
|
astroe n00b
Joined: 12 Aug 2004 Posts: 14 Location: Bucharest, Romania
|
Posted: Tue Mar 29, 2016 7:56 am Post subject: |
|
|
Do you also have something like:
Code: | wpa_supplicant_wlp3s0="-Dwext" |
in your /etc/conf.d/net ? [/code] |
|
Back to top |
|
|
charles17 Advocate
Joined: 02 Mar 2008 Posts: 3664
|
Posted: Tue Mar 29, 2016 8:22 am Post subject: |
|
|
Please see the iwlwifi article. It should tell you everything you need to know about the Centrino Wireless-N 135.
Then come back with all information from the Check the setup section. |
|
Back to top |
|
|
|