| View previous topic :: View next topic |
| Author |
Message |
fresherthanever
n00b
Joined: 11 Nov 2013
Posts: 40
Location: Houston
|
 Posted: Thu Sep 10, 2015 2:16 am Post subject: eudev and noob question |
 |
|
I recently decided to give eudev a go and drift yet a little further from systemd, but I can't figure out how to get my box to connect to the internet on boot. I have wpa_supplicant and I use dhcp previously, but whenever I run wpa_supplicant -Dnl80211 -iwlan0 -c/etc/wpa_supplicant/wpa_supplicant.conf -B && dhcpcd, I still can't connect on boot. I can only acquire a lease when I unplug the network adapter and plug it back in, and oddly, if wpa_supplicant and dhcpcd have not been started already while I manually reset my adapter it will also not connect until reboot, though the network worked fine while using sysctl-udev.
I am running the Tenda W311U, so I'm using kernel modules rt2800usb/rt2800lib, they are loaded on boot. In the kernel I have set net.ifnames=0 so I have wlan0/eth0 naming schemes.
When I have some more time, I can fill in the details, (e.g., the dmesg, ifconfig, conf.d/net).
_________________
Specs: AMD FX-6100|ASUS M5A97 AM3+|XFX AMD Radeon HD 6870|1TB 7200RPM/500GB 7200RPM|8GB DDR3 1600MHz |
|
| Back to top |
|
 |
fresherthanever
n00b
Joined: 11 Nov 2013
Posts: 40
Location: Houston
|
| Posted: Fri Sep 11, 2015 2:17 am Post subject: |
|
|
dmesg:
| Code: | [ 8.185542] udevd[3403]: starting version 3.1.2
[ 8.806426] usb 4-1: reset high-speed USB device number 2 using ehci-pci
[ 8.947062] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3070, rev 0201 detected
[ 8.947148] kvm: Nested Virtualization enabled
[ 8.947152] kvm: Nested Paging enabled
[ 8.976528] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0005 detected
[ 8.976867] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 8.977115] usbcore: registered new interface driver rt2800usb
[ 10.305054] cfg80211: Calling CRDA to update world regulatory domain
[ 10.576666] cfg80211: World regulatory domain updated:
[ 10.576671] cfg80211: DFS Master region: unset
[ 10.576671] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 10.576678] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.576679] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.576680] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.576682] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 10.576685] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 10.576687] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 10.576689] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.576691] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 10.670132] Adding 4194300k swap on /dev/sda3. Priority:-1 extents:1 across:4194300k FS
[ 11.168787] EXT4-fs (sda4): re-mounted. Opts: (null)
[ 11.223015] EXT4-fs (sda6): re-mounted. Opts: (null)
[ 11.240261] mount (3759) used greatest stack depth: 12632 bytes left
[ 11.407562] EXT2-fs (sda5): warning: mounting unchecked fs, running e2fsck is recommended
[ 12.660399] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'
[ 12.739151] ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.29
[ 13.084111] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 13.084273] ip (4169) used greatest stack depth: 10720 bytes left
[ 13.321235] r8169 0000:02:00.0 eth0: link down
[ 13.321276] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 13.394357] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready |
Kernel options:
| Code: | | \vmlinuz-4.1.5.efi ro root=/dev/sda4 dolvm net.ifnames=0 initrd=\initramfs-4.1.5.img |
(I use UEFI & rEFInd)
rc-update show:
| Code: | alsasound | boot
binfmt | boot
bootmisc | boot
devfs | sysinit
dhcpcd | default
dmesg | sysinit
fsck | boot
hostname | boot default
hwclock | boot
keymaps | boot
killprocs | shutdown
kmod-static-nodes | sysinit
local | default
localmount | boot
loopback | boot
modules | boot
mount-ro | shutdown
mtab | boot
net.wlan0 | default
netmount | default
procfs | boot
root | boot
savecache | shutdown
swap | boot
swapfiles | boot
sysctl | boot
sysfs | sysinit
termencoding | boot
tmpfiles.dev | sysinit
tmpfiles.setup | boot
udev | sysinit
urandom | boot
|
_________________
Specs: AMD FX-6100|ASUS M5A97 AM3+|XFX AMD Radeon HD 6870|1TB 7200RPM/500GB 7200RPM|8GB DDR3 1600MHz |
|
| Back to top |
|
|
charles17
Advocate
Joined: 02 Mar 2008
Posts: 3664
|
| Posted: Fri Sep 11, 2015 6:22 am Post subject: |
|
|
| fresherthanever wrote: | | rc-update show: |
There seems to be net.wlan0 and dhcpcd both in runlevel default.
You'd better decide for one of them, since when using netifrc you need not have dhcpcd in the runlevel.
rc-config show --all should show you which services successfully started.
What about ifconfig -a? |
|
| Back to top |
|
|
fresherthanever
n00b
Joined: 11 Nov 2013
Posts: 40
Location: Houston
|
| Posted: Wed Sep 16, 2015 8:30 pm Post subject: |
|
|
| charles17 wrote: | | fresherthanever wrote: | | rc-update show: |
There seems to be net.wlan0 and dhcpcd both in runlevel default.
You'd better decide for one of them, since when using netifrc you need not have dhcpcd in the runlevel.
rc-config show --all should show you which services successfully started.
What about ifconfig -a? |
Thanks, apologies for the long wait.
My sudo rc-config show --all doesnt bring up dhcpcd:
| Code: | Status of init scripts in runlevel "boot"
alsasound [started]
binfmt [started]
bootmisc [started]
fsck [started]
hostname [started]
hwclock [started]
keymaps [started]
localmount [started]
loopback [started]
modules [started]
mtab [started]
procfs [started]
root [started]
swap [started]
swapfiles [started]
sysctl [started]
termencoding [started]
tmpfiles.setup [started]
urandom [started]
Status of init scripts in runlevel "default"
hostname [started]
local [started]
netmount [stopped]
net.wlan0 [stopped]
Status of init scripts in runlevel "shutdown"
killprocs [stopped]
mount-ro [stopped]
savecache [stopped]
Status of init scripts in runlevel "sysinit"
devfs [started]
dmesg [started]
kmod-static-nodes [started]
sysfs [started]
tmpfiles.dev [started]
udev [started]
|
my interfaces:
| Code: | eth0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
inet6 fe80::d40f:f61f:769d:29a2 prefixlen 64 scopeid 0x20<link>
ether c8:60:00:14:cc:6d txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
eth1: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
inet6 fe80::70bb:9bc8:7507:cb8 prefixlen 64 scopeid 0x20<link>
ether 68:05:ca:01:7d:d7 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 40 memory 0xfe8c0000-fe8e0000
gre0: flags=128<NOARP> mtu 1476
unspec 00-00-00-00-62-62-3A-39-00-00-00-00-00-00-00-00 txqueuelen 0 (UNSPEC)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
gretap0: flags=4098<BROADCAST,MULTICAST> mtu 1462
inet6 fe80::24b:5bfc:8a9e:b148 prefixlen 64 scopeid 0x20<link>
ether 00:00:00:00:00:00 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
ip6_vti0: flags=128<NOARP> mtu 1500
unspec 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 txqueuelen 0 (UNSPEC)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
ip6gre0: flags=128<NOARP> mtu 1448
unspec 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 txqueuelen 0 (UNSPEC)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
ip6tnl0: flags=128<NOARP> mtu 1452
unspec 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 txqueuelen 0 (UNSPEC)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 0 (Local Loopback)
RX packets 56 bytes 3864 (3.7 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 56 bytes 3864 (3.7 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
sit0: flags=128<NOARP> mtu 1480
sit txqueuelen 0 (IPv6-in-IPv4)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
tunl0: flags=128<NOARP> mtu 1480
tunnel txqueuelen 0 (IPIP Tunnel)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.1.7 netmask 255.255.255.0 broadcast 192.168.1.255
inet6 fe80::319b:d686:d22a:189b prefixlen 64 scopeid 0x20<link>
ether c8:3a:35:cb:0c:91 txqueuelen 1000 (Ethernet)
RX packets 48113 bytes 61620183 (58.7 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 32783 bytes 4625355 (4.4 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
|
The inconvienent thing is that I have to unplug my adapter each time and plug it back in for the service to restart, I can't do it from terminal. rfkill list wifi agrees with the assessment that nothing is soft/hard blocked on my system.
Thanks 
_________________
Specs: AMD FX-6100|ASUS M5A97 AM3+|XFX AMD Radeon HD 6870|1TB 7200RPM/500GB 7200RPM|8GB DDR3 1600MHz |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Networking & Security
