Gentoo Forums :: View topic - [SOLVED]Cannot bring wireless interface up

[SOLVED]Cannot bring wireless interface up

View unanswered posts
View posts from last 24 hours

Gentoo Forums Forum Index

Networking & Security

View previous topic :: View next topic

Author

Message

Mr Victory
n00b
n00b

Joined: 10 May 2021
Posts: 3

Posted: Mon May 10, 2021 12:23 pm Post subject: [SOLVED]Cannot bring wireless interface up

Hello, I cannot bring my wireless interface up with this command:

Code:

ip link set wlp2s0 up

This problem occured as soon as I logged in to my freshly installed Gentoo system. I could connect to internet with net-setup within the livecd. After the installation ip link did not show my wireless interface, to solve this problem I compiled the kernel again with the rtl8723b module and ip link displayed the wireless interface as wlp2s0. My network card is Realtek Semiconductor Co., Ltd. RTL8723BE PCIe Wireless Network Adapter. What should I do to bring my wireless interface up?
ip link set wlp2s0 up prints no text and returns. If I try to initialise wpa_supplicant with the command below, I get

Code:

wpa_supplicant -B -i wlp2s0 -c /etc/wpa_supplicant/wpa_supplicant.conf

Code:

Successfully initialized wpa_supplicant
Could not set interface wlp2s0 flags (UP): Success
nl80211: Could not set interface 'wlp2s0' UP
nl80211: deinit ifname=wlp2s0 disabled_11b_rates=0
wlp2s0: Failed to initialize driver interface

ip -d link prints this:

Code:

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 promiscuity 0 minmtu 0 maxmtu 0 addrgenmode eui64 numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
2: enp1s0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 1000
link/ether 3c:52:82:db:8e:5f brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 9194 addrgenmode none numtxqueues 1 numrxqueues 1 gso_max_size 64000 gso_max_segs 64
3: wlp2s0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether f8:28:19:53:4b:c9 brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 256 maxmtu 2304 addrgenmode none numtxqueues 4 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
4: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/sit 0.0.0.0 brd 0.0.0.0 promiscuity 0 minmtu 1280 maxmtu 65555
sit ip6ip remote any local any ttl 64 nopmtudisc addrgenmode eui64 numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535

lspci -vvvk prints this:

Code:

00:00.0 Host bridge: Intel Corporation Xeon E3-1200 v5/E3-1500 v5/6th Gen Core Processor Host Bridge/DRAM Registers (rev 08)
Subsystem: Hewlett-Packard Company Xeon E3-1200 v5/E3-1500 v5/6th Gen Core Processor Host Bridge/DRAM Registers
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=10 <?>
Kernel driver in use: skl_uncore

00:02.0 VGA compatible controller: Intel Corporation Skylake GT2 [HD Graphics 520] (rev 07) (prog-if 00 [VGA controller])
DeviceName: Onboard IGD
Subsystem: Hewlett-Packard Company Skylake GT2 [HD Graphics 520]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 122
Region 0: Memory at de000000 (64-bit, non-prefetchable) [size=16M]
Region 2: Memory at c0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at f000 [size=64]
Expansion ROM at 000c0000 [virtual] [disabled] [size=128K]
Capabilities: [40] Vendor Specific Information: Len=0c <?>
Capabilities: [70] Express (v2) Root Complex Integrated Endpoint, MSI 00
   DevCap: MaxPayload 128 bytes, PhantFunc 0
      ExtTag- RBE+ FLReset+
   DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
      RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- FLReset-
      MaxPayload 128 bytes, MaxReadReq 128 bytes
   DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr- TransPend-
   DevCap2: Completion Timeout: Not Supported, TimeoutDis- NROPrPrP- LTR-
      10BitTagComp- 10BitTagReq- OBFF Not Supported, ExtFmt- EETLPPrefix-
      EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
      FRS-
      AtomicOpsCap: 32bit- 64bit- 128bitCAS-
   DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- OBFF Disabled,
      AtomicOpsCtl: ReqEn-
Capabilities: [ac] MSI: Enable+ Count=1/1 Maskable- 64bit-
   Address: fee01004 Data: 4021
Capabilities: [d0] Power Management version 2
   Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
   Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Process Address Space ID (PASID)
   PASIDCap: Exec+ Priv-, Max PASID Width: 14
   PASIDCtl: Enable- Exec- Priv-
Capabilities: [200 v1] Address Translation Service (ATS)
   ATSCap: Invalidate Queue Depth: 00
   ATSCtl: Enable-, Smallest Translation Unit: 00
Capabilities: [300 v1] Page Request Interface (PRI)
   PRICtl: Enable- Reset-
   PRISta: RF- UPRGI- Stopped-
   Page Request Capacity: 00008000, Page Request Allocation: 00000000
Kernel driver in use: i915

00:14.0 USB controller: Intel Corporation Sunrise Point-LP USB 3.0 xHCI Controller (rev 21) (prog-if 30 [XHCI])
Subsystem: Hewlett-Packard Company Sunrise Point-LP USB 3.0 xHCI Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 125
Region 0: Memory at df210000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [70] Power Management version 2
   Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
   Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] MSI: Enable+ Count=1/8 Maskable- 64bit+
   Address: 00000000fee08004 Data: 4022
Kernel driver in use: xhci_hcd

00:16.0 Communication controller: Intel Corporation Sunrise Point-LP CSME HECI #1 (rev 21)
Subsystem: Hewlett-Packard Company Sunrise Point-LP CSME HECI
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at df22d000 (64-bit, non-prefetchable) [disabled] [size=4K]
Capabilities: [50] Power Management version 3
   Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
   Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] MSI: Enable- Count=1/1 Maskable- 64bit+
   Address: 0000000000000000 Data: 0000

00:17.0 SATA controller: Intel Corporation Sunrise Point-LP SATA Controller [AHCI mode] (rev 21) (prog-if 01 [AHCI 1.0])
Subsystem: Hewlett-Packard Company Sunrise Point-LP SATA Controller [AHCI mode]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 123
Region 0: Memory at df228000 (32-bit, non-prefetchable) [size=8K]
Region 1: Memory at df22c000 (32-bit, non-prefetchable) [size=256]
Region 2: I/O ports at f090 [size=8]
Region 3: I/O ports at f080 [size=4]
Region 4: I/O ports at f060 [size=32]
Region 5: Memory at df22b000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
   Address: fee02004 Data: 4022
Capabilities: [70] Power Management version 3
   Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
   Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
Kernel driver in use: ahci

00:1d.0 PCI bridge: Intel Corporation Sunrise Point-LP PCI Express Root Port #9 (rev f1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 120
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000efff [size=4K]
Memory behind bridge: df100000-df1fffff [size=1M]
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff [disabled]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
   PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
   DevCap: MaxPayload 256 bytes, PhantFunc 0
      ExtTag- RBE+
   DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
      RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
      MaxPayload 128 bytes, MaxReadReq 128 bytes
   DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
   LnkCap: Port #9, Speed 8GT/s, Width x1, ASPM L1, Exit Latency L1 <16us
      ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp+
   LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+
      ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
   LnkSta: Speed 2.5GT/s (downgraded), Width x1 (ok)
      TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
   SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
      Slot #12, PowerLimit 10.000W; Interlock- NoCompl+
   SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
      Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
   SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
      Changed: MRL- PresDet+ LinkState+
   RootCap: CRSVisible-
   RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
   RootSta: PME ReqID 0000, PMEStatus- PMEPending-
   DevCap2: Completion Timeout: Range ABC, TimeoutDis+ NROPrPrP- LTR+
      10BitTagComp- 10BitTagReq- OBFF Not Supported, ExtFmt- EETLPPrefix-
      EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
      FRS- LN System CLS Not Supported, TPHComp- ExtTPHComp- ARIFwd+
      AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
   DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- OBFF Disabled, ARIFwd-
      AtomicOpsCtl: ReqEn- EgressBlck-
   LnkCap2: Supported Link Speeds: 2.5-8GT/s, Crosslink- Retimer- 2Retimers- DRS-
   LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis-
      Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
      Compliance De-emphasis: -6dB
   LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete- EqualizationPhase1-
      EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
      Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
   Address: fee04004 Data: 4021
Capabilities: [90] Subsystem: Hewlett-Packard Company Sunrise Point-LP PCI Express Root Port
Capabilities: [a0] Power Management version 3
   Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
   Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v0] Null
Capabilities: [140 v1] Access Control Services
   ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd- EgressCtrl- DirectTrans-
   ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
Capabilities: [220 v1] Secondary PCI Express
   LnkCtl3: LnkEquIntrruptEn- PerformEqu-
   LaneErrStat: 0
Kernel driver in use: pcieport

00:1d.1 PCI bridge: Intel Corporation Sunrise Point-LP PCI Express Root Port #10 (rev f1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 121
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000d000-0000dfff [size=4K]
Memory behind bridge: df000000-df0fffff [size=1M]
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff [disabled]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
   PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
   DevCap: MaxPayload 256 bytes, PhantFunc 0
      ExtTag- RBE+
   DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
      RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
      MaxPayload 128 bytes, MaxReadReq 128 bytes
   DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
   LnkCap: Port #10, Speed 8GT/s, Width x1, ASPM L1, Exit Latency L1 <16us
      ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp+
   LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+
      ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
   LnkSta: Speed 2.5GT/s (downgraded), Width x1 (ok)
      TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
   SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
      Slot #13, PowerLimit 10.000W; Interlock- NoCompl+
   SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
      Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
   SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
      Changed: MRL- PresDet- LinkState+
   RootCap: CRSVisible-
   RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
   RootSta: PME ReqID 0000, PMEStatus- PMEPending-
   DevCap2: Completion Timeout: Range ABC, TimeoutDis+ NROPrPrP- LTR+
      10BitTagComp- 10BitTagReq- OBFF Not Supported, ExtFmt- EETLPPrefix-
      EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
      FRS- LN System CLS Not Supported, TPHComp- ExtTPHComp- ARIFwd+
      AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
   DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR+ OBFF Disabled, ARIFwd-
      AtomicOpsCtl: ReqEn- EgressBlck-
   LnkCap2: Supported Link Speeds: 2.5-8GT/s, Crosslink- Retimer- 2Retimers- DRS-
   LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis-
      Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
      Compliance De-emphasis: -6dB
   LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete- EqualizationPhase1-
      EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
      Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
   Address: fee08004 Data: 4021
Capabilities: [90] Subsystem: Hewlett-Packard Company Sunrise Point-LP PCI Express Root Port
Capabilities: [a0] Power Management version 3
   Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
   Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v0] Null
Capabilities: [140 v1] Access Control Services
   ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd- EgressCtrl- DirectTrans-
   ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
Capabilities: [220 v1] Secondary PCI Express
   LnkCtl3: LnkEquIntrruptEn- PerformEqu-
   LaneErrStat: 0
Kernel driver in use: pcieport

00:1f.0 ISA bridge: Intel Corporation Sunrise Point-LP LPC Controller (rev 21)
Subsystem: Hewlett-Packard Company Sunrise Point-LP LPC Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0

00:1f.2 Memory controller: Intel Corporation Sunrise Point-LP PMC (rev 21)
Subsystem: Hewlett-Packard Company Sunrise Point-LP PMC
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at df224000 (32-bit, non-prefetchable) [size=16K]

00:1f.3 Audio device: Intel Corporation Sunrise Point-LP HD Audio (rev 21)
Subsystem: Hewlett-Packard Company Sunrise Point-LP HD Audio
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 16
Region 0: Memory at df220000 (64-bit, non-prefetchable) [size=16K]
Region 4: Memory at df200000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 3
   Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
   Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] MSI: Enable- Count=1/1 Maskable- 64bit+
   Address: 0000000000000000 Data: 0000
Kernel driver in use: snd_hda_intel

00:1f.4 SMBus: Intel Corporation Sunrise Point-LP SMBus (rev 21)
Subsystem: Hewlett-Packard Company Sunrise Point-LP SMBus
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 16
Region 0: Memory at df22a000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at f040 [size=32]
Kernel driver in use: i801_smbus

01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 10)
Subsystem: Hewlett-Packard Company RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at e000 [size=256]
Region 2: Memory at df104000 (64-bit, non-prefetchable) [size=4K]
Region 4: Memory at df100000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
   Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
   Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
   Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v2) Endpoint, MSI 01
   DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
      ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 10.000W
   DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
      RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
      MaxPayload 128 bytes, MaxReadReq 4096 bytes
   DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
   LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <64us
      ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
   LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+
      ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
   LnkSta: Speed 2.5GT/s (ok), Width x1 (ok)
      TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
   DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ NROPrPrP- LTR+
      10BitTagComp- 10BitTagReq- OBFF Via message/WAKE#, ExtFmt- EETLPPrefix-
      EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
      FRS- TPHComp- ExtTPHComp-
      AtomicOpsCap: 32bit- 64bit- 128bitCAS-
   DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR+ OBFF Disabled,
      AtomicOpsCtl: ReqEn-
   LnkCap2: Supported Link Speeds: 2.5GT/s, Crosslink- Retimer- 2Retimers- DRS-
   LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
      Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
      Compliance De-emphasis: -6dB
   LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1-
      EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
      Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [b0] MSI-X: Enable+ Count=4 Masked-
   Vector table: BAR=4 offset=00000000
   PBA: BAR=4 offset=00000800
Capabilities: [d0] Vital Product Data
   Not readable
Capabilities: [100 v2] Advanced Error Reporting
   UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
   UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
   UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
   CESta: RxErr+ BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
   CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
   AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn-
      MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
   HeaderLog: 00000000 00000000 00000000 00000000
Capabilities: [140 v1] Virtual Channel
   Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
   Arb: Fixed- WRR32- WRR64- WRR128-
   Ctrl: ArbSelect=Fixed
   Status: InProgress-
   VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
      Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
      Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
      Status: NegoPending- InProgress-
Capabilities: [160 v1] Device Serial Number 01-00-5f-8e-db-82-52-3c
Capabilities: [170 v1] Latency Tolerance Reporting
   Max snoop latency: 3145728ns
   Max no snoop latency: 3145728ns
Capabilities: [178 v1] L1 PM Substates
   L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+
         PortCommonModeRestoreTime=150us PortTPowerOnTime=150us
   L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1-
         T_CommonMode=0us LTR1.2_Threshold=0ns
   L1SubCtl2: T_PwrOn=10us
Kernel driver in use: r8169

02:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8723BE PCIe Wireless Network Adapter
Subsystem: Hewlett-Packard Company RTL8723BE PCIe Wireless Network Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at d000 [size=256]
Region 2: Memory at df000000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
   Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
   Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
   Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v2) Endpoint, MSI 00
   DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 <64us
      ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 10.000W
   DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
      RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
      MaxPayload 128 bytes, MaxReadReq 512 bytes
   DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
   LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <512ns, L1 <64us
      ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp-
   LnkCtl: ASPM Disabled; RCB 64 bytes, Disabled- CommClk+
      ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
   LnkSta: Speed 2.5GT/s (ok), Width x1 (ok)
      TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
   DevCap2: Completion Timeout: Not Supported, TimeoutDis+ NROPrPrP- LTR+
      10BitTagComp- 10BitTagReq- OBFF Via message/WAKE#, ExtFmt- EETLPPrefix-
      EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
      FRS- TPHComp- ExtTPHComp-
      AtomicOpsCap: 32bit- 64bit- 128bitCAS-
   DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis+ LTR+ OBFF Disabled,
      AtomicOpsCtl: ReqEn-
   LnkCap2: Supported Link Speeds: 2.5GT/s, Crosslink- Retimer- 2Retimers- DRS-
   LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
      Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
      Compliance De-emphasis: -6dB
   LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1-
      EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
      Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [100 v2] Advanced Error Reporting
   UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
   UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
   UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
   CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
   CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
   AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn-
      MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
   HeaderLog: 00000000 00000000 00000000 00000000
Capabilities: [140 v1] Device Serial Number 00-23-b7-fe-ff-4c-e0-00
Capabilities: [150 v1] Latency Tolerance Reporting
   Max snoop latency: 3145728ns
   Max no snoop latency: 3145728ns
Capabilities: [158 v1] L1 PM Substates
   L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+
         PortCommonModeRestoreTime=150us PortTPowerOnTime=150us
   L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1-
         T_CommonMode=0us LTR1.2_Threshold=0ns
   L1SubCtl2: T_PwrOn=10us
Kernel driver in use: rtl8723be

00:00.0 Host bridge: Intel Corporation Xeon E3-1200 v5/E3-1500 v5/6th Gen Core Processor Host Bridge/DRAM Registers (rev 08)
Subsystem: Hewlett-Packard Company Xeon E3-1200 v5/E3-1500 v5/6th Gen Core Processor Host Bridge/DRAM Registers
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=10 <?>
Kernel driver in use: skl_uncore

00:02.0 VGA compatible controller: Intel Corporation Skylake GT2 [HD Graphics 520] (rev 07) (prog-if 00 [VGA controller])
DeviceName: Onboard IGD
Subsystem: Hewlett-Packard Company Skylake GT2 [HD Graphics 520]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 122
Region 0: Memory at de000000 (64-bit, non-prefetchable) [size=16M]
Region 2: Memory at c0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at f000 [size=64]
Expansion ROM at 000c0000 [virtual] [disabled] [size=128K]
Capabilities: [40] Vendor Specific Information: Len=0c <?>
Capabilities: [70] Express (v2) Root Complex Integrated Endpoint, MSI 00
   DevCap: MaxPayload 128 bytes, PhantFunc 0
      ExtTag- RBE+ FLReset+
   DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
      RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- FLReset-
      MaxPayload 128 bytes, MaxReadReq 128 bytes
   DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr- TransPend-
   DevCap2: Completion Timeout: Not Supported, TimeoutDis- NROPrPrP- LTR-
      10BitTagComp- 10BitTagReq- OBFF Not Supported, ExtFmt- EETLPPrefix-
      EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
      FRS-
      AtomicOpsCap: 32bit- 64bit- 128bitCAS-
   DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- OBFF Disabled,
      AtomicOpsCtl: ReqEn-
Capabilities: [ac] MSI: Enable+ Count=1/1 Maskable- 64bit-
   Address: fee01004 Data: 4021
Capabilities: [d0] Power Management version 2
   Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
   Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Process Address Space ID (PASID)
   PASIDCap: Exec+ Priv-, Max PASID Width: 14
   PASIDCtl: Enable- Exec- Priv-
Capabilities: [200 v1] Address Translation Service (ATS)
   ATSCap: Invalidate Queue Depth: 00
   ATSCtl: Enable-, Smallest Translation Unit: 00
Capabilities: [300 v1] Page Request Interface (PRI)
   PRICtl: Enable- Reset-
   PRISta: RF- UPRGI- Stopped-
   Page Request Capacity: 00008000, Page Request Allocation: 00000000
Kernel driver in use: i915

00:14.0 USB controller: Intel Corporation Sunrise Point-LP USB 3.0 xHCI Controller (rev 21) (prog-if 30 [XHCI])
Subsystem: Hewlett-Packard Company Sunrise Point-LP USB 3.0 xHCI Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 125
Region 0: Memory at df210000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [70] Power Management version 2
   Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
   Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] MSI: Enable+ Count=1/8 Maskable- 64bit+
   Address: 00000000fee08004 Data: 4022
Kernel driver in use: xhci_hcd

00:16.0 Communication controller: Intel Corporation Sunrise Point-LP CSME HECI #1 (rev 21)
Subsystem: Hewlett-Packard Company Sunrise Point-LP CSME HECI
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at df22d000 (64-bit, non-prefetchable) [disabled] [size=4K]
Capabilities: [50] Power Management version 3
   Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
   Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] MSI: Enable- Count=1/1 Maskable- 64bit+
   Address: 0000000000000000 Data: 0000

00:17.0 SATA controller: Intel Corporation Sunrise Point-LP SATA Controller [AHCI mode] (rev 21) (prog-if 01 [AHCI 1.0])
Subsystem: Hewlett-Packard Company Sunrise Point-LP SATA Controller [AHCI mode]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 123
Region 0: Memory at df228000 (32-bit, non-prefetchable) [size=8K]
Region 1: Memory at df22c000 (32-bit, non-prefetchable) [size=256]
Region 2: I/O ports at f090 [size=8]
Region 3: I/O ports at f080 [size=4]
Region 4: I/O ports at f060 [size=32]
Region 5: Memory at df22b000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
   Address: fee02004 Data: 4022
Capabilities: [70] Power Management version 3
   Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
   Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
Kernel driver in use: ahci

00:1d.0 PCI bridge: Intel Corporation Sunrise Point-LP PCI Express Root Port #9 (rev f1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 120
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000efff [size=4K]
Memory behind bridge: df100000-df1fffff [size=1M]
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff [disabled]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
   PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
   DevCap: MaxPayload 256 bytes, PhantFunc 0
      ExtTag- RBE+
   DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
      RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
      MaxPayload 128 bytes, MaxReadReq 128 bytes
   DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
   LnkCap: Port #9, Speed 8GT/s, Width x1, ASPM L1, Exit Latency L1 <16us
      ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp+
   LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+
      ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
   LnkSta: Speed 2.5GT/s (downgraded), Width x1 (ok)
      TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
   SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
      Slot #12, PowerLimit 10.000W; Interlock- NoCompl+
   SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
      Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
   SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
      Changed: MRL- PresDet+ LinkState+
   RootCap: CRSVisible-
   RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
   RootSta: PME ReqID 0000, PMEStatus- PMEPending-
   DevCap2: Completion Timeout: Range ABC, TimeoutDis+ NROPrPrP- LTR+
      10BitTagComp- 10BitTagReq- OBFF Not Supported, ExtFmt- EETLPPrefix-
      EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
      FRS- LN System CLS Not Supported, TPHComp- ExtTPHComp- ARIFwd+
      AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
   DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- OBFF Disabled, ARIFwd-
      AtomicOpsCtl: ReqEn- EgressBlck-
   LnkCap2: Supported Link Speeds: 2.5-8GT/s, Crosslink- Retimer- 2Retimers- DRS-
   LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis-
      Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
      Compliance De-emphasis: -6dB
   LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete- EqualizationPhase1-
      EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
      Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
   Address: fee04004 Data: 4021
Capabilities: [90] Subsystem: Hewlett-Packard Company Sunrise Point-LP PCI Express Root Port
Capabilities: [a0] Power Management version 3
   Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
   Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v0] Null
Capabilities: [140 v1] Access Control Services
   ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd- EgressCtrl- DirectTrans-
   ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
Capabilities: [220 v1] Secondary PCI Express
   LnkCtl3: LnkEquIntrruptEn- PerformEqu-
   LaneErrStat: 0
Kernel driver in use: pcieport

00:1d.1 PCI bridge: Intel Corporation Sunrise Point-LP PCI Express Root Port #10 (rev f1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 121
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000d000-0000dfff [size=4K]
Memory behind bridge: df000000-df0fffff [size=1M]
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff [disabled]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
   PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
   DevCap: MaxPayload 256 bytes, PhantFunc 0
      ExtTag- RBE+
   DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
      RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
      MaxPayload 128 bytes, MaxReadReq 128 bytes
   DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
   LnkCap: Port #10, Speed 8GT/s, Width x1, ASPM L1, Exit Latency L1 <16us
      ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp+
   LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+
      ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
   LnkSta: Speed 2.5GT/s (downgraded), Width x1 (ok)
      TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
   SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
      Slot #13, PowerLimit 10.000W; Interlock- NoCompl+
   SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
      Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
   SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
      Changed: MRL- PresDet- LinkState+
   RootCap: CRSVisible-
   RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
   RootSta: PME ReqID 0000, PMEStatus- PMEPending-
   DevCap2: Completion Timeout: Range ABC, TimeoutDis+ NROPrPrP- LTR+
      10BitTagComp- 10BitTagReq- OBFF Not Supported, ExtFmt- EETLPPrefix-
      EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
      FRS- LN System CLS Not Supported, TPHComp- ExtTPHComp- ARIFwd+
      AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
   DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR+ OBFF Disabled, ARIFwd-
      AtomicOpsCtl: ReqEn- EgressBlck-
   LnkCap2: Supported Link Speeds: 2.5-8GT/s, Crosslink- Retimer- 2Retimers- DRS-
   LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis-
      Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
      Compliance De-emphasis: -6dB
   LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete- EqualizationPhase1-
      EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
      Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
   Address: fee08004 Data: 4021
Capabilities: [90] Subsystem: Hewlett-Packard Company Sunrise Point-LP PCI Express Root Port
Capabilities: [a0] Power Management version 3
   Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
   Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v0] Null
Capabilities: [140 v1] Access Control Services
   ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd- EgressCtrl- DirectTrans-
   ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
Capabilities: [220 v1] Secondary PCI Express
   LnkCtl3: LnkEquIntrruptEn- PerformEqu-
   LaneErrStat: 0
Kernel driver in use: pcieport

00:1f.0 ISA bridge: Intel Corporation Sunrise Point-LP LPC Controller (rev 21)
Subsystem: Hewlett-Packard Company Sunrise Point-LP LPC Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0

00:1f.2 Memory controller: Intel Corporation Sunrise Point-LP PMC (rev 21)
Subsystem: Hewlett-Packard Company Sunrise Point-LP PMC
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at df224000 (32-bit, non-prefetchable) [size=16K]

00:1f.3 Audio device: Intel Corporation Sunrise Point-LP HD Audio (rev 21)
Subsystem: Hewlett-Packard Company Sunrise Point-LP HD Audio
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 16
Region 0: Memory at df220000 (64-bit, non-prefetchable) [size=16K]
Region 4: Memory at df200000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 3
   Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
   Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] MSI: Enable- Count=1/1 Maskable- 64bit+
   Address: 0000000000000000 Data: 0000
Kernel driver in use: snd_hda_intel

00:1f.4 SMBus: Intel Corporation Sunrise Point-LP SMBus (rev 21)
Subsystem: Hewlett-Packard Company Sunrise Point-LP SMBus
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 16
Region 0: Memory at df22a000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at f040 [size=32]
Kernel driver in use: i801_smbus

01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 10)
Subsystem: Hewlett-Packard Company RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at e000 [size=256]
Region 2: Memory at df104000 (64-bit, non-prefetchable) [size=4K]
Region 4: Memory at df100000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
   Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
   Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
   Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v2) Endpoint, MSI 01
   DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
      ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 10.000W
   DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
      RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
      MaxPayload 128 bytes, MaxReadReq 4096 bytes
   DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
   LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <64us
      ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
   LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+
      ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
   LnkSta: Speed 2.5GT/s (ok), Width x1 (ok)
      TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
   DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ NROPrPrP- LTR+
      10BitTagComp- 10BitTagReq- OBFF Via message/WAKE#, ExtFmt- EETLPPrefix-
      EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
      FRS- TPHComp- ExtTPHComp-
      AtomicOpsCap: 32bit- 64bit- 128bitCAS-
   DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR+ OBFF Disabled,
      AtomicOpsCtl: ReqEn-
   LnkCap2: Supported Link Speeds: 2.5GT/s, Crosslink- Retimer- 2Retimers- DRS-
   LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
      Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
      Compliance De-emphasis: -6dB
   LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1-
      EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
      Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [b0] MSI-X: Enable+ Count=4 Masked-
   Vector table: BAR=4 offset=00000000
   PBA: BAR=4 offset=00000800
Capabilities: [d0] Vital Product Data
   Not readable
Capabilities: [100 v2] Advanced Error Reporting
   UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
   UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
   UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
   CESta: RxErr+ BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
   CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
   AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn-
      MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
   HeaderLog: 00000000 00000000 00000000 00000000
Capabilities: [140 v1] Virtual Channel
   Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
   Arb: Fixed- WRR32- WRR64- WRR128-
   Ctrl: ArbSelect=Fixed
   Status: InProgress-
   VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
      Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
      Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
      Status: NegoPending- InProgress-
Capabilities: [160 v1] Device Serial Number 01-00-5f-8e-db-82-52-3c
Capabilities: [170 v1] Latency Tolerance Reporting
   Max snoop latency: 3145728ns
   Max no snoop latency: 3145728ns
Capabilities: [178 v1] L1 PM Substates
   L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+
         PortCommonModeRestoreTime=150us PortTPowerOnTime=150us
   L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1-
         T_CommonMode=0us LTR1.2_Threshold=0ns
   L1SubCtl2: T_PwrOn=10us
Kernel driver in use: r8169

02:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8723BE PCIe Wireless Network Adapter
Subsystem: Hewlett-Packard Company RTL8723BE PCIe Wireless Network Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at d000 [size=256]
Region 2: Memory at df000000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
   Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
   Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
   Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v2) Endpoint, MSI 00
   DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 <64us
      ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 10.000W
   DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
      RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
      MaxPayload 128 bytes, MaxReadReq 512 bytes
   DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
   LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <512ns, L1 <64us
      ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp-
   LnkCtl: ASPM Disabled; RCB 64 bytes, Disabled- CommClk+
      ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
   LnkSta: Speed 2.5GT/s (ok), Width x1 (ok)
      TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
   DevCap2: Completion Timeout: Not Supported, TimeoutDis+ NROPrPrP- LTR+
      10BitTagComp- 10BitTagReq- OBFF Via message/WAKE#, ExtFmt- EETLPPrefix-
      EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
      FRS- TPHComp- ExtTPHComp-
      AtomicOpsCap: 32bit- 64bit- 128bitCAS-
   DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis+ LTR+ OBFF Disabled,
      AtomicOpsCtl: ReqEn-
   LnkCap2: Supported Link Speeds: 2.5GT/s, Crosslink- Retimer- 2Retimers- DRS-
   LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
      Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
      Compliance De-emphasis: -6dB
   LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1-
      EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
      Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [100 v2] Advanced Error Reporting
   UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
   UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
   UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
   CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
   CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
   AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn-
      MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
   HeaderLog: 00000000 00000000 00000000 00000000
Capabilities: [140 v1] Device Serial Number 00-23-b7-fe-ff-4c-e0-00
Capabilities: [150 v1] Latency Tolerance Reporting
   Max snoop latency: 3145728ns
   Max no snoop latency: 3145728ns
Capabilities: [158 v1] L1 PM Substates
   L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+
         PortCommonModeRestoreTime=150us PortTPowerOnTime=150us
   L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1-
         T_CommonMode=0us LTR1.2_Threshold=0ns
   L1SubCtl2: T_PwrOn=10us
Kernel driver in use: rtl8723be

Last edited by Mr Victory on Mon May 10, 2021 1:32 pm; edited 1 time in total

alamahant
Advocate

Joined: 23 Mar 2019
Posts: 3879

Posted: Mon May 10, 2021 12:28 pm Post subject:

Hi
do you have these

Code:

/lib/firmware/rtlwifi/rtl8723befw.bin
/lib/firmware/rtlwifi/rtl8723befw_36.bin

?
If not plz run

Code:

emerge -av linux-firmware

_________________

NeddySeagoon
Administrator

Joined: 05 Jul 2003
Posts: 54216
Location: 56N 3W

Posted: Mon May 10, 2021 12:40 pm Post subject:

Mr Victory, Welcome to Gentoo. What alamahant pointed to is required but may not be sufficient. It depends how your kernel is compiled. The firmware will be loaded at the time the kernel module is initialised, so it has to be accessible then. When the kernel driver is configured as <M>, the firmware can be read from /lib/firmware.That works. When the kernel driver is configured as <*> then the driver will be initalised before root is mounted. Thus /lib/firmware is not available. The firmware must be built into the kernel binary. _________________ Regards, NeddySeagoon Computer users fall into two groups:- those that do backups those that have never had a hard drive fail.

Mr Victory
n00b
n00b

Joined: 10 May 2021
Posts: 3

Posted: Mon May 10, 2021 1:05 pm Post subject:

First of all, thanks for the instant support! I expected to wait for a day for a reply but I got 2 replies in 20 minutes.
I have rtl8723befw_36.bin and rtl8723befw.bin files. I had manually compiled my kernel with the instructions from the Handbook and added support for my wireless card as <*>. I will recompile the kernel with <M> and try again. I guess the firmware is not loaded according to dmesg, there are relevant lines:

Code:

[ 1.068131] rtl8723be: Using firmware rtlwifi/rtl8723befw_36.bin
[ 1.068413] rtl8723be 0000:02:00.0: Direct firmware load for rtlwifi/rtl8723befw_36.bin failed with error -2
[ 1.068419] rtl8723be 0000:02:00.0: Direct firmware load for rtlwifi/rtl8723befw.bin failed with error -2
[ 1.068420] rtlwifi: Loading alternative firmware rtlwifi/rtl8723befw.bin
[ 1.068421] rtlwifi: Selected firmware is not available
[ 1.068886] ieee80211 phy0: Selected rate control algorithm 'rtl_rc'
[ 1.069118] rtlwifi: rtlwifi: wireless switch is on

NeddySeagoon
Administrator

Joined: 05 Jul 2003
Posts: 54216
Location: 56N 3W

Posted: Mon May 10, 2021 1:15 pm Post subject:

Mr Victory,

Timing is just luck. Its who is around and when. Gentoo spans the world so you do need to wait 24 hours for everyone to see your posts.

Your dmesg confirms the guesswork.

When you reoot into your new kernel, run the command

Code:

uname -a

and look at the date and time.
Check that you are actually running the new kernel. Its very easy to boot into the old kernel still.
If that happens, you will have fixed your problem but won't know it.
_________________
Regards,

NeddySeagoon

Computer users fall into two groups:-
those that do backups
those that have never had a hard drive fail.

Mr Victory
n00b
n00b

Joined: 10 May 2021
Posts: 3

Posted: Mon May 10, 2021 1:30 pm Post subject: Solved

I compiled the kernel again but with <M> instead of <*> for the wireless card, rebooted, checked that I was running the newer kernel, loaded the module with modprobe rtl8723be and ip link showed the interface UP. I configured network with wpa_supplicant and I could ping 1.1.1.1. Thanks again for the support.

Display posts from previous:

	Gentoo Forums Forum Index Networking & Security	All times are GMT
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum

Copyright 2001-2024 Gentoo Foundation, Inc. Designed by Kyle Manna © 2003; Style derived from original subSilver theme. | Hosting by Gossamer Threads Inc. © | Powered by phpBB 2.0.23-gentoo-p11 © 2001, 2002 phpBB Group
Privacy Policy