| View previous topic :: View next topic |
| Author |
Message |
beerbellyswan
Tux's lil' helper
Joined: 01 May 2004
Posts: 128
Location: mendon, ny
|
 Posted: Tue Jun 19, 2018 9:15 pm Post subject: tg3 kernel module not loaded at boot prior to net.eth0 setup |
 |
|
Hi folks - this has been a problem for a couple years and im just now aggravated enough to resolve it. When i boot, the tg3 kernel module is not being loaded early on so the net.eth0 setup fails. Message from boot.log:
| Code: |
Executing: /lib64/rc/sh/openrc-run.sh /lib64/rc/sh/openrc-run.sh /etc/init.d/net.eth0 start
Bringing up interface eth0
Caching network module dependencies need dbus
Skipping module adsl due to missing program: /usr/sbin/adsl-start /usr/sbin/pppoe-start
Skipping module br2684ctl due to missing program: br2684ctl
Skipping module clip due to missing program: /usr/sbin/atmsigd
Skipping module ethtool due to missing program: ethtool
Skipping module netplugd due to missing program: /sbin/netplugd
Skipping module ifplugd due to missing program: /usr/sbin/ifplugd
Skipping module ipppd due to missing program: /usr/sbin/ipppd
Skipping module iwconfig due to missing program: /sbin/iwconfig
Skipping module firewalld due to missing program: firewall-cmd
Skipping module pump due to missing program: /sbin/pump
Loaded modules: apipa arping bonding l2tp tuntap bridge ccwgroup dummy hsr macvlan macchanger macnet wpa_supplicant ssidnet iproute2 pppd system vlan dhcpcd ip6rd ip6to4
ip link set dev eth0 up
ERROR: interface eth0 does not exist
Ensure that you have loaded the correct kernel module for your hardware
ERROR: net.eth0 failed to start
ERROR: cannot start netmount as net.eth0 would not start
|
my workaround to this point is to simply run this command after logging in:
| Code: |
rmmod tg3 && modprobe tg3 && ifconfig eth0
|
So tg3 is being loaded - but AFTER eth0 is being set up. I can't figure out why this is happening - any pointers? |
|
| Back to top |
|
 |
krinn
Watchman
Joined: 02 May 2003
Posts: 7470
|
| Posted: Tue Jun 19, 2018 10:41 pm Post subject: Re: tg3 kernel module not loaded at boot prior to net.eth0 s |
|
|
| beerbellyswan wrote: | | Code: |
rmmod tg3 && modprobe tg3 && ifconfig eth0
|
So tg3 is being loaded - but AFTER eth0 is being set up. I can't figure out why this is happening - any pointers? |
Why you rmmod it?
you just need ifconfig eth0 to make it start or the reload sequence is need? |
|
| Back to top |
|
|
beerbellyswan
Tux's lil' helper
Joined: 01 May 2004
Posts: 128
Location: mendon, ny
|
| Posted: Tue Jun 19, 2018 11:38 pm Post subject: |
|
|
@krinn - I remove it and reload it so that broadcom* starts using it. This is what it looks like when i first boot:
| Code: |
office /home/rdswan # lsmod|grep tg3
tg3 184320 0
libphy 77824 1 tg3
office /home/rdswan #
|
And when it looks like that, i get this message when trying to start eth0:
| Code: |
office /home/rdswan # /etc/init.d/net.eth0 start
* Executing: /lib64/rc/sh/openrc-run.sh /lib64/rc/sh/openrc-run.sh /etc/init.d/net.eth0 start
* Bringing up interface eth0
* Skipping module adsl due to missing program: /usr/sbin/adsl-start /usr/sbin/pppoe-start
* Skipping module br2684ctl due to missing program: br2684ctl
* Skipping module clip due to missing program: /usr/sbin/atmsigd
* Skipping module ethtool due to missing program: ethtool
* Skipping module netplugd due to missing program: /sbin/netplugd
* Skipping module ifplugd due to missing program: /usr/sbin/ifplugd
* Skipping module ipppd due to missing program: /usr/sbin/ipppd
* Skipping module iwconfig due to missing program: /sbin/iwconfig
* Skipping module firewalld due to missing program: firewall-cmd
* Skipping module pump due to missing program: /sbin/pump
* Loaded modules: apipa arping bonding l2tp tuntap bridge ccwgroup dummy hsr macvlan macchanger macnet wpa_supplicant ssidnet iproute2 pppd system vlan dhcpcd ip6rd ip6to4
* ip link set dev eth0 up
* ERROR: interface eth0 does not exist
* Ensure that you have loaded the correct kernel module for your hardware
* ERROR: net.eth0 failed to start
office /home/rdswan #
|
But when i remove it and reload it,it looks correct:
| Code: |
office /home/rdswan # rmmod tg3 && modprobe tg3
office /home/rdswan # lsmod|grep tg3
tg3 184320 0
libphy 77824 3 tg3,broadcom,bcm_phy_lib
office /home/rdswan #
|
and then eth0 starts right up:
| Code: |
office /home/rdswan # /etc/init.d/net.eth0 start
* Executing: /lib64/rc/sh/openrc-run.sh /lib64/rc/sh/openrc-run.sh /etc/init.d/net.eth0 start
* Bringing up interface eth0
* Skipping module adsl due to missing program: /usr/sbin/adsl-start /usr/sbin/pppoe-start
* Skipping module br2684ctl due to missing program: br2684ctl
* Skipping module clip due to missing program: /usr/sbin/atmsigd
* Skipping module ethtool due to missing program: ethtool
* Skipping module netplugd due to missing program: /sbin/netplugd
* Skipping module ifplugd due to missing program: /usr/sbin/ifplugd
* Skipping module ipppd due to missing program: /usr/sbin/ipppd
* Skipping module iwconfig due to missing program: /sbin/iwconfig
* Skipping module firewalld due to missing program: firewall-cmd
* Skipping module pump due to missing program: /sbin/pump
* Loaded modules: apipa arping bonding l2tp tuntap bridge ccwgroup dummy hsr macvlan macchanger macnet wpa_supplicant ssidnet iproute2 pppd system vlan dhcpcd ip6rd ip6to4
* ip link set dev eth0 up
* Configuring eth0 for MAC address 5C:F9:DD:6C:CC:26 ... [ ok ]
* dhcp ...
* Running dhcpcd ...
sending commands to master dhcpcd process [ ok ]
* received address 192.168.1.174/24 [ ok ]
* ip -4 route flush table cache dev eth0
* ip -6 route flush table cache dev eth0
office /home/rdswan #
|
So again - all the modules work, and so does the device. But somethings up with the ordering of it all... |
|
| Back to top |
|
|
Jaglover
Watchman
Joined: 29 May 2005
Posts: 8291
Location: Saint Amant, Acadiana
|
|
| Back to top |
|
|
russK
l33t
Joined: 27 Jun 2006
Posts: 665
|
| Posted: Wed Jun 20, 2018 3:02 am Post subject: |
|
|
Whole dmesg would help yes.
I'm wondering if it's firmware related.
Regards |
|
| Back to top |
|
|
beerbellyswan
Tux's lil' helper
Joined: 01 May 2004
Posts: 128
Location: mendon, ny
|
| Posted: Wed Jun 20, 2018 12:31 pm Post subject: |
|
|
I would think it's this part (which i assume is when tg3 is being added at boot):
| Code: |
[ 6.827496] igb: Copyright (c) 2007-2014 Intel Corporation.
[ 6.834278] pcnet32: pcnet32.c:v1.35 21.Apr.2008 tsbogend@alpha.franken.de
[ 6.845812] sky2: driver version 1.30
[ 6.862417] tg3.c:v3.137 (May 11, 2014)
[ 6.869818] libphy: tg3 mdio bus: probed
[ 6.869820] tg3 0000:03:00.0: No PHY devices
[ 6.869849] tg3 0000:03:00.0: Problem fetching invariants of chip, aborting
[ 6.880776] scsi 6:0:0:0: Direct-Access Generic- SD/MMC 1.00 PQ: 0 ANSI: 0
|
Later on i see better messaging (which i assume is when tg3 is removed/added manually be me):
| Code: |
[ 30.834074] caller _nv001169rm+0xe3/0x1d0 [nvidia] mapping multiple BARs
[ 30.996897] nvidia-modeset: Allocated GPU:0 (GPU-c6a60c2d-f350-339c-2f3d-2d4947294efa) @ PCI:0000:01:00.0
[ 225.640546] tg3.c:v3.137 (May 11, 2014)
[ 225.671773] libphy: tg3 mdio bus: probed
[ 225.731489] Broadcom BCM57780 300:01: attached PHY driver [Broadcom BCM57780] (mii_bus:phy_addr=300:01, irq=POLL)
[ 225.731888] tg3 0000:03:00.0 eth0: Tigon3 [partno(BCM57788) rev 57780001] (PCI Express) MAC address 5c:f9:dd:6c:cc:26
[ 225.731891] tg3 0000:03:00.0 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[ 225.731893] tg3 0000:03:00.0 eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[ 225.928849] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 225.929430] tg3 0000:03:00.0 eth0: Link is down
[ 230.049090] tg3 0000:03:00.0 eth0: Link is up at 1000 Mbps, full duplex
[ 230.049092] tg3 0000:03:00.0 eth0: Flow control is off for TX and off for RX
[ 230.049103] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
|
For the complete dmesg:
https://paste.pound-python.org/show/ux7isNsDxqfiMYLrA3L3/ |
|
| Back to top |
|
|
krinn
Watchman
Joined: 02 May 2003
Posts: 7470
|
| Posted: Wed Jun 20, 2018 2:48 pm Post subject: |
|
|
| Code: | [ 0.019269] core: PMU erratum BJ122, BV98, HSD29 workaround disabled, HT off
[ 0.009501] core: PEBS disabled due to CPU errata, please upgrade microcode
[ 0.035760] pci 0000:00:01.0: ASPM: current common clock configuration is broken, reconfiguring
[ 0.041997] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0
[ 0.042215] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0
[ 0.042431] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0
|
This make a lot of, well, shit.
The problem with the tg3 is certainly because the bios didn't assign an irq to the card when the driver gets load (the card use either LNKE LNKF or LNKG which are invalid with an irq0 set, irq0 should be the one for the timer, and it's never good to share this one with other devices)
On next attempt, it succeed by polling irq.
What you could do:
* update your bios (but i could guess your m/b manufacturer sucks so much that i wouldn't be surprise no update exist).
* boot with irqpoll=yes set (a workaround, certainly the one that could easy solve your issue)
* you should update microcode earlier (yes sadly, initrd method), cpu is update but the PEBS error comes prior the update (i don't have any idea of what this does, but this doesn't still look good)
* try switching to hpet timer (at least 100% working for me) you can set it in kernel or boot with clocksource=hpet)
* kick your m/b manufacturer's ass, he really deserve it
* your bios should have a "pnp bios" feature, enable it if disable, disable it if enable (yeah i know, weak, but with buggy bios, that's to try)
* use your own kernel rather than genkernel (i never trust something i couldn't understand, and i have never understand genkernel)
* as an easy test, use a livecd (sysrescuecd is pretty nice), to see how its kernel handle your, well, mess.
* some bios offer acpi versions implementation, try switch this too
* i think i remember someone showing a doc on howto fix ACPI, but i cannot point you to it
who the hell has done this shitty board? |
|
| Back to top |
|
|
beerbellyswan
Tux's lil' helper
Joined: 01 May 2004
Posts: 128
Location: mendon, ny
|
| Posted: Wed Jun 20, 2018 8:25 pm Post subject: |
|
|
Thanks for the detailed list of potential culprits krinn - unfortunately I dont think that's the problem. The m/b manufacturer is DELL, and the BIOS is the latest version of it (i did just check). I also tried booting in with the two options (irqpoll=yes clocksource=hpet), but neither worked. Not sure what you mean by "update microcode earlier" so i didn't try that
latest dmesg here:
https://paste.pound-python.org/show/PfW2RBPlIeXp6rXZoBks/ |
|
| Back to top |
|
|
russK
l33t
Joined: 27 Jun 2006
Posts: 665
|
|
| Back to top |
|
|
beerbellyswan
Tux's lil' helper
Joined: 01 May 2004
Posts: 128
Location: mendon, ny
|
| Posted: Thu Jun 21, 2018 12:51 pm Post subject: |
|
|
| @russK - yep, i tried that as well with no luck. the same exact messaging exists during boot. |
|
| Back to top |
|
|
|
Networking & Security
