| View previous topic :: View next topic |
| Author |
Message |
Goshanecr
Apprentice
Joined: 17 Aug 2005
Posts: 158
Location: Russia
|
 Posted: Tue May 22, 2018 7:32 pm Post subject: zram strange issue |
 |
|
Good day!
I'm setup zram with wiki.
/etc/conf.d/zram-init
| Code: | load_on_start="yes"
unload_on_stop="yes"
num_devices="1"
type0="swap"
flag0=
size0="192"
maxs0=1
algo0=lz4
|
zramctl
| Code: |
NAME ALGORITHM DISKSIZE DATA COMPR TOTAL STREAMS MOUNTPOINT
/dev/zram0 lz4 192M 191,8M 61,5M 65,4M 1 [SWAP] |
cat /proc/swaps
| Code: | Filename Type Size Used Priority
/dev/sda3 partition 1048572 183948 -2
/dev/zram0 partition 196604 196348 16383
|
And my question is illustrated in zramctl and /proc/swaps output. Why when my zram based swap has 192MB and from zramctl output it compressed size just 61.5MB but it used full and start swapping to disk based swap?!!
I think that for example if I have 100Mb zram based swap with approximately compression ratio 3, then system can fill it to 300MB uncompressed data, but there I have strange statistics.
Please somebody explain that issue to me. Maybe I'm misunderstanding something? |
|
| Back to top |
|
 |
Zucca
Moderator
Joined: 14 Jun 2007
Posts: 3345
Location: Rasi, Finland
|
| Posted: Tue May 22, 2018 7:53 pm Post subject: |
|
|
If your only usage for zram is swap, then I'd suggest you to move to zswap. It's hazzle-free and, as the name suggests, meant for compressing swap (only).
You can search the kernel documentation for it by running | Code: | | find /usr/src/ -type f -name 'zswap.txt' |
There isn't Gentoo wiki page for it (yet). But Arch wiki page shoud get you started too.
As for the strange behaviour of your zram... I don't have any idea atm...
_________________
..: Zucca :..
Gentoo IRC channels reside on Libera.Chat.
--
| Quote: | | I am NaN! I am a man! |
|
|
| Back to top |
|
|
Goshanecr
Apprentice
Joined: 17 Aug 2005
Posts: 158
Location: Russia
|
| Posted: Tue May 22, 2018 8:02 pm Post subject: |
|
|
Yes, my usage of zram only for swap, but not for additional swap space, but for something like "Trying to expand low RAM amount by cost of some CPU time".
Now I want to understand why zram based swap show compression from zramctl output, but when size of DATA section equals size of zram it ends up, but COMPR section shows more than 3x lower amount.
| Zucca wrote: | | ... then I'd suggest you to move to zswap. It's hazzle-free and, as the name suggests, meant for compressing swap (only). |
Zucca thanks for suggestion! When I solve that issue, I'm try to use zswap for disk based swap also and maybe will have zram swap + zswap  |
|
| Back to top |
|
|
Goshanecr
Apprentice
Joined: 17 Aug 2005
Posts: 158
Location: Russia
|
| Posted: Tue May 22, 2018 8:19 pm Post subject: |
|
|
Maybe I understand.... If I think right, amount of ram allocated to zram not piece which cuts from ram, but final size of data (uncompressed) which will fits in it, and amount of ram allocated to it dynamically changes with type of data stored on it, but not more than allocated amount.
So for example if I have 256MB ram and I give 100MB to zram which fills with data with compression ratio 2x, so it consumes 50MB, and I have in that case 256-50+100=306MB virtually RAM.
Am I right? If so, is it possible to set target minimum compression ratio for data stored on zram swap, if not then it sends to backend swap? |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Kernel & Hardware
