| View previous topic :: View next topic |
| Author |
Message |
truekaiser
l33t
Joined: 05 Mar 2004
Posts: 801
|
 Posted: Sat May 14, 2016 5:14 am Post subject: Setting up Hostapd [Abandoned] |
 |
|
Edit: changed out the card with an atheros one.
I am trying to get hostapd to work on the following wireless card. Using the 8812au driver from, http://gpo.zugaina.org/net-wireless/rtl8812au with these options.
https://wikidevi.com/wiki/TP-LINK_Archer_T4UHoptions rtw_vht_enable=1 rtw_ht_enable=1 rtw_hwpwrp_detect=0
| Code: | Bus 008 Device 002: ID 2357:0103
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x2357
idProduct 0x0103
bcdDevice 0.00
iManufacturer 1 Realtek
iProduct 2 802.11n NIC
iSerial 3 123456
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 53
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 5
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 1
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
can't get debug descriptor: Resource temporarily unavailable
Device Status: 0x0002
(Bus Powered)
Remote Wakeup Enabled
|
Hostapd config Stuff with * in front i set myself. The rest is from the default file.
| Code: |
*interface=wlp0s16f1u2
*driver=nl80211
logger_syslog=-1
logger_syslog_level=2
logger_stdout=-1
logger_stdout_level=2
ctrl_interface=/var/run/hostapd
ctrl_interface_group=0
*ssid="actest"
*country_code=US
*hw_mode=a
*channel=36
beacon_int=100
dtim_period=2
max_num_sta=255
rts_threshold=2347
fragm_threshold=2346
*macaddr_acl=0
*auth_algs=1
wmm_ac_bk_cwmin=4
wmm_ac_bk_cwmax=10
wmm_ac_bk_aifs=7
wmm_ac_bk_txop_limit=0
wmm_ac_bk_acm=0
wmm_ac_be_aifs=3
wmm_ac_be_cwmin=4
wmm_ac_be_cwmax=10
wmm_ac_be_txop_limit=0
wmm_ac_be_acm=0
wmm_ac_vi_aifs=2
wmm_ac_vi_cwmin=3
wmm_ac_vi_cwmax=4
wmm_ac_vi_txop_limit=94
wmm_ac_vi_acm=0
wmm_ac_vo_aifs=2
wmm_ac_vo_cwmin=2
wmm_ac_vo_cwmax=3
wmm_ac_vo_txop_limit=47
wmm_ac_vo_acm=0
*ieee80211n=1
*ht_capab=[HT40+][SHORT-GI-20][SHORT-GI-40][MAX-AMSDU-7935]
*ieee80211ac=1
vht_oper_chwidth=1
vht_oper_centr_freq_seg0_idx=42
vht_oper_centr_freq_seg1_idx=159
eapol_key_index_workaround=0
eap_server=0
own_ip_addr=127.0.0.1
*wpa=2
*wpa_passphrase=******************************************
*wpa_key_mgmt=WPA-PSK WPA-PSK-SHA256
*wpa_pairwise=CCMP
*rsn_pairwise=CCMP
|
Hostapd errors out with this.
| Code: | random: Trying to read entropy from /dev/random
Configuration file: /etc/hostapd/hostapd.conf
ctrl_interface_group=0
rfkill: Cannot open RFKILL control device
nl80211: RFKILL status not available
nl80211: Supported cipher 00-0f-ac:1
nl80211: Supported cipher 00-0f-ac:5
nl80211: Supported cipher 00-0f-ac:2
nl80211: Supported cipher 00-0f-ac:4
nl80211: Using driver-based off-channel TX
nl80211: interface wlp0s16f1u2 in phy phy2
nl80211: Set mode ifindex 8 iftype 3 (AP)
nl80211: Setup AP(wlp0s16f1u2) - device_ap_sme=1 use_monitor=1
nl80211: Enable Probe Request reporting nl_preq=0x1748a40
nl80211: Register frame type=0x40 (WLAN_FC_STYPE_PROBE_REQ) nl_handle=0x1748a40 match=
nl80211: Add own interface ifindex 8
nl80211: if_indices[16]: 8
phy: phy2
BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits)
wlp0s16f1u2: interface state UNINITIALIZED->COUNTRY_UPDATE
Previous country code US, new country code US
nl80211: Regulatory information - country=US
nl80211: 2402-2472 @ 40 MHz 30 mBm
nl80211: 5170-5250 @ 80 MHz 23 mBm
nl80211: 5250-5330 @ 80 MHz 23 mBm (DFS)
nl80211: 5490-5730 @ 160 MHz 23 mBm (DFS)
nl80211: 5735-5835 @ 80 MHz 30 mBm
nl80211: 57240-63720 @ 2160 MHz 40 mBm
nl80211: Added 802.11b mode based on 802.11g information
Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=30 dBm
Allowed channel: mode=2 chan=36 freq=5180 MHz max_tx_power=23 dBm
Allowed channel: mode=2 chan=38 freq=5190 MHz max_tx_power=23 dBm
Allowed channel: mode=2 chan=40 freq=5200 MHz max_tx_power=23 dBm
Allowed channel: mode=2 chan=42 freq=5210 MHz max_tx_power=23 dBm
Allowed channel: mode=2 chan=44 freq=5220 MHz max_tx_power=23 dBm
Allowed channel: mode=2 chan=46 freq=5230 MHz max_tx_power=23 dBm
Allowed channel: mode=2 chan=48 freq=5240 MHz max_tx_power=23 dBm
Allowed channel: mode=2 chan=149 freq=5745 MHz max_tx_power=30 dBm
Allowed channel: mode=2 chan=153 freq=5765 MHz max_tx_power=30 dBm
Allowed channel: mode=2 chan=157 freq=5785 MHz max_tx_power=30 dBm
Allowed channel: mode=2 chan=161 freq=5805 MHz max_tx_power=30 dBm
Allowed channel: mode=2 chan=165 freq=5825 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=30 dBm
hw vht capab: 0x0, conf vht capab: 0x0
wlp0s16f1u2: interface state COUNTRY_UPDATE->HT_SCAN
Scan for neighboring BSSes prior to enabling 40 MHz channel
40 MHz affected channel range: [5170,5210] MHz
wlp0s16f1u2: nl80211: scan request
nl80211: Scan frequency 5180 MHz
nl80211: Scan frequency 5190 MHz
nl80211: Scan frequency 5200 MHz
nl80211: Scan frequency 5210 MHz
Scan requested (ret=0) - scan timeout 10 seconds
Interface initialization will be completed in a callback
ctrl_iface not configured!
random: Got 20/20 bytes from /dev/random
RTM_NEWLINK: ifi_index=8 ifname=wlp0s16f1u2 operstate=2 linkmode=0 ifi_family=0 ifi_flags=0x1003 ([UP])
nl80211: Event message available
nl80211: Drv Event 33 (NL80211_CMD_TRIGGER_SCAN) received for wlp0s16f1u2
wlp0s16f1u2: nl80211: Scan trigger
wlp0s16f1u2: Event SCAN_STARTED (47) received
Unknown event 47
nl80211: Event message available
nl80211: Drv Event 34 (NL80211_CMD_NEW_SCAN_RESULTS) received for wlp0s16f1u2
wlp0s16f1u2: nl80211: New scan results available
nl80211: Scan included frequencies: 5180 5190 5200 5210
wlp0s16f1u2: Event SCAN_RESULTS (3) received
nl80211: Received scan results (5 BSSes)
HT40: control channel: 36 secondary channel: 40
Completing interface initialization
Mode: IEEE 802.11a Channel: 36 Frequency: 5180 MHz
DFS 0 channels required radar detection
Could not set channel for kernel driver
Interface initialization failed
wlp0s16f1u2: interface state HT_SCAN->DISABLED
wlp0s16f1u2: AP-DISABLED
hostapd_interface_deinit_free(0x1748010)
hostapd_interface_deinit_free: num_bss=1 conf->num_bss=1
hostapd_interface_deinit(0x1748010)
wlp0s16f1u2: interface state DISABLED->DISABLED
hostapd_bss_deinit: deinit bss wlp0s16f1u2
wlp0s16f1u2: Deauthenticate all stations
nl80211: sta_remove -> DEL_STATION wlp0s16f1u2 ff:ff:ff:ff:ff:ff --> -22 (Invalid argument)
wlp0s16f1u2: AP-DISABLED
hostapd_cleanup(hapd=0x174bb80 (wlp0s16f1u2))
hostapd_free_hapd_data: Interface wlp0s16f1u2 wasn't started
hostapd_interface_deinit_free: driver=0x4edd80 drv_priv=0x174ca60 -> hapd_deinit
nl80211: deinit ifname=wlp0s16f1u2 disabled_11b_rates=0
nl80211: Disable Probe Request reporting nl_preq=0x8888888889fc02c9
nl80211: Remove monitor interface: refcount=0
nl80211: Remove beacon (ifindex=8)
netlink: Operstate: ifindex=8 linkmode=0 (kernel-control), operstate=6 (IF_OPER_UP)
nl80211: Set mode ifindex 8 iftype 2 (STATION)
nl80211: Teardown AP(wlp0s16f1u2) - device_ap_sme=1 use_monitor=1
hostapd_interface_free(0x1748010)
hostapd_interface_free: free hapd 0x174bb80
hostapd_cleanup_iface(0x1748010)
hostapd_cleanup_iface_partial(0x1748010)
hostapd_cleanup_iface: free iface=0x1748010
|
And iw list
| Code: | Wiphy phy2
max # scan SSIDs: 9
max scan IEs length: 2304 bytes
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP (00-0f-ac:4)
Available Antennas: TX 0 RX 0
Supported interface modes:
* IBSS
* managed
* AP
* monitor
* P2P-client
* P2P-GO
Band 1:
Capabilities: 0x1862
HT20/HT40
Static SM Power Save
RX HT20 SGI
RX HT40 SGI
No RX STBC
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 16 usec (0x07)
HT TX/RX MCS rate indexes supported: 0-15, 32
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps
* 5.5 Mbps
* 11.0 Mbps
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 2412 MHz [1] (30.0 dBm)
* 2417 MHz [2] (30.0 dBm)
* 2422 MHz [3] (30.0 dBm)
* 2427 MHz [4] (30.0 dBm)
* 2432 MHz [5] (30.0 dBm)
* 2437 MHz [6] (30.0 dBm)
* 2442 MHz [7] (30.0 dBm)
* 2447 MHz [8] (30.0 dBm)
* 2452 MHz [9] (30.0 dBm)
* 2457 MHz [10] (30.0 dBm)
* 2462 MHz [11] (30.0 dBm)
* 2467 MHz [12] (disabled)
* 2472 MHz [13] (disabled)
* 2484 MHz [14] (disabled)
Band 2:
Capabilities: 0x1862
HT20/HT40
Static SM Power Save
RX HT20 SGI
RX HT40 SGI
No RX STBC
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 16 usec (0x07)
HT TX/RX MCS rate indexes supported: 0-15, 32
Bitrates (non-HT):
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 5170 MHz [34] (disabled)
* 5180 MHz [36] (23.0 dBm)
* 5190 MHz [38] (23.0 dBm)
* 5200 MHz [40] (23.0 dBm)
* 5210 MHz [42] (23.0 dBm)
* 5220 MHz [44] (23.0 dBm)
* 5230 MHz [46] (23.0 dBm)
* 5240 MHz [48] (23.0 dBm)
* 5260 MHz [52] (23.0 dBm) (radar detection)
DFS state: usable (for 2719 sec)
DFS CAC time: 60000 ms
* 5280 MHz [56] (23.0 dBm) (radar detection)
DFS state: usable (for 2719 sec)
DFS CAC time: 60000 ms
* 5300 MHz [60] (23.0 dBm) (radar detection)
DFS state: usable (for 2719 sec)
DFS CAC time: 60000 ms
* 5320 MHz [64] (23.0 dBm) (radar detection)
DFS state: usable (for 2719 sec)
DFS CAC time: 60000 ms
* 5500 MHz [100] (23.0 dBm) (radar detection)
DFS state: usable (for 2719 sec)
DFS CAC time: 60000 ms
* 5520 MHz [104] (23.0 dBm) (radar detection)
DFS state: usable (for 2719 sec)
DFS CAC time: 60000 ms
* 5540 MHz [108] (23.0 dBm) (radar detection)
DFS state: usable (for 2719 sec)
DFS CAC time: 60000 ms
* 5560 MHz [112] (23.0 dBm) (radar detection)
DFS state: usable (for 2719 sec)
DFS CAC time: 60000 ms
* 5580 MHz [116] (23.0 dBm) (radar detection)
DFS state: usable (for 2719 sec)
DFS CAC time: 60000 ms
* 5600 MHz [120] (23.0 dBm) (radar detection)
DFS state: usable (for 2719 sec)
DFS CAC time: 60000 ms
* 5620 MHz [124] (23.0 dBm) (radar detection)
DFS state: usable (for 2719 sec)
DFS CAC time: 60000 ms
* 5640 MHz [128] (23.0 dBm) (radar detection)
DFS state: usable (for 2719 sec)
DFS CAC time: 60000 ms
* 5660 MHz [132] (23.0 dBm) (radar detection)
DFS state: usable (for 2719 sec)
DFS CAC time: 60000 ms
* 5680 MHz [136] (23.0 dBm) (radar detection)
DFS state: usable (for 2719 sec)
DFS CAC time: 60000 ms
* 5700 MHz [140] (23.0 dBm) (radar detection)
DFS state: usable (for 2719 sec)
DFS CAC time: 60000 ms
* 5745 MHz [149] (30.0 dBm)
* 5765 MHz [153] (30.0 dBm)
* 5785 MHz [157] (30.0 dBm)
* 5805 MHz [161] (30.0 dBm)
* 5825 MHz [165] (30.0 dBm)
* 5920 MHz [184] (disabled)
* 5940 MHz [188] (disabled)
* 5960 MHz [192] (disabled)
* 5980 MHz [196] (disabled)
* 6000 MHz [200] (disabled)
* 6020 MHz [204] (disabled)
* 6040 MHz [208] (disabled)
* 6060 MHz [212] (disabled)
* 6080 MHz [216] (disabled)
Supported commands:
* new_interface
* set_interface
* new_key
* start_ap
* new_station
* set_bss
* join_ibss
* set_pmksa
* del_pmksa
* flush_pmksa
* remain_on_channel
* frame
* set_channel
* connect
* disconnect
Supported TX frame types:
* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
* IBSS: 0xd0
* managed: 0x40 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
software interface modes (can always be added):
* monitor
interface combinations are not supported
Device supports scan flush.
|
Last edited by truekaiser on Thu May 19, 2016 1:50 am; edited 1 time in total |
|
| Back to top |
|
 |
khayyam
Watchman
Joined: 07 Jun 2012
Posts: 6227
Location: Room 101
|
| Posted: Sat May 14, 2016 12:57 pm Post subject: Re: Setting up Hostapd |
|
|
| truekaiser wrote: | | iw list: | Supported interface modes:
* IBSS
* managed
* AP
* monitor
* P2P-client
* P2P-GO |
|
truekaiser ... the first thing I notice is that this particular driver doesn't report it supporting 'AP/VLAN' and this would be needed for a monitor (use_monitor=1). I suspect this is why it reports that it can't set the channel. I might get a better idea if you pastebin'd the following:
| Code: | | hostapd -dtB /etc/hostapd/hostapd.conf |
best ... khay |
|
| Back to top |
|
|
truekaiser
l33t
Joined: 05 Mar 2004
Posts: 801
|
| Posted: Sat May 14, 2016 3:05 pm Post subject: Re: Setting up Hostapd |
|
|
| khayyam wrote: | | truekaiser wrote: | | iw list: | Supported interface modes:
* IBSS
* managed
* AP
* monitor
* P2P-client
* P2P-GO |
|
truekaiser ... the first thing I notice is that this particular driver doesn't report it supporting 'AP/VLAN' and this would be needed for a monitor (use_monitor=1). I suspect this is why it reports that it can't set the channel. I might get a better idea if you pastebin'd the following:
| Code: | | hostapd -dtB /etc/hostapd/hostapd.conf |
best ... khay |
here you go.
| Code: | 1463240658.491349: random: Trying to read entropy from /dev/random
1463240658.491461: Configuration file: /etc/hostapd/hostapd.conf
1463240658.492257: ctrl_interface_group=0
1463240658.493783: rfkill: Cannot open RFKILL control device
1463240658.493800: nl80211: RFKILL status not available
1463240658.494091: nl80211: Supported cipher 00-0f-ac:1
1463240658.494108: nl80211: Supported cipher 00-0f-ac:5
1463240658.494120: nl80211: Supported cipher 00-0f-ac:2
1463240658.494127: nl80211: Supported cipher 00-0f-ac:4
1463240658.494240: nl80211: Using driver-based off-channel TX
1463240658.494272: nl80211: interface wlp0s16f1u2 in phy phy2
1463240658.494308: nl80211: Set mode ifindex 8 iftype 3 (AP)
1463240658.494359: nl80211: Setup AP(wlp0s16f1u2) - device_ap_sme=1 use_monitor=1
1463240658.494387: nl80211: Enable Probe Request reporting nl_preq=0x203ba40
1463240658.494396: nl80211: Register frame type=0x40 (WLAN_FC_STYPE_PROBE_REQ) nl_handle=0x203ba40 match=
1463240658.494960: nl80211: Add own interface ifindex 8
1463240658.494977: nl80211: if_indices[16]: 8
1463240658.495012: phy: phy2
1463240658.495026: BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits)
1463240658.495122: wlp0s16f1u2: interface state UNINITIALIZED->COUNTRY_UPDATE
1463240658.495205: Previous country code US, new country code US
1463240658.495586: nl80211: Regulatory information - country=US
1463240658.495601: nl80211: 2402-2472 @ 40 MHz 30 mBm
1463240658.495617: nl80211: 5170-5250 @ 80 MHz 23 mBm
1463240658.495633: nl80211: 5250-5330 @ 80 MHz 23 mBm (DFS)
1463240658.495648: nl80211: 5490-5730 @ 160 MHz 23 mBm (DFS)
1463240658.495662: nl80211: 5735-5835 @ 80 MHz 30 mBm
1463240658.495675: nl80211: 57240-63720 @ 2160 MHz 40 mBm
1463240658.495733: nl80211: Added 802.11b mode based on 802.11g information
1463240658.495749: hw vht capab: 0x0, conf vht capab: 0x0
1463240658.495761: wlp0s16f1u2: interface state COUNTRY_UPDATE->HT_SCAN
1463240658.495772: Scan for neighboring BSSes prior to enabling 40 MHz channel
1463240658.495783: 40 MHz affected channel range: [5170,5210] MHz
1463240658.495803: wlp0s16f1u2: nl80211: scan request
1463240658.495873: Scan requested (ret=0) - scan timeout 10 seconds
1463240658.495891: Interface initialization will be completed in a callback
1463240658.495902: ctrl_iface not configured!
|
That's interesting because it says it supports Ap mode in that list and in supported RX frame types it has this.
| Code: | | * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 |
I am just scratching my head because others have reported being able to set up AP's with this chip and i want to set up an AC ap. |
|
| Back to top |
|
|
truekaiser
l33t
Joined: 05 Mar 2004
Posts: 801
|
| Posted: Sun May 15, 2016 12:14 am Post subject: |
|
|
I forgot to add.
| Code: | config_enp1s0="dhcp"
#brctl_br0="setfd 0
#sethello 2
#stp on"
#bridge_br0="wlp0s16f1u2 enp1s0"
#config_enp1s0="null"
#config_wlp0s16f1u2="null" #address needed for hostapd
#config_br0="dhcp"
#rc_net_br0_need="net.enp1s0 net.wlp0s16f1u2"
#needed for hostapd
modules_wlp0s16f1u2="!iwconfig !wpa_supplicant"
config_wlp0s16f1u2="192.168.0.2/24"
channel_wlp0s16f1u2="1"
essid_wlp0s16f1u2="test"
mode_wlp0s16f1u2="master"
|
The ultimate goal here is to have the system act as a wireless access point to my existing router, not replace it. So I want it as a plain bridge to pass dhcp over to the connecting clients. As well as the system acting as a nas point.
Should i also post a kernel config? I configured it to this https://wiki.gentoo.org/wiki/AC1200_Wireless_Adapters |
|
| Back to top |
|
|
|
Networking & Security
