| View previous topic :: View next topic |
| Author |
Message |
Akaihiryuu
l33t
Joined: 08 May 2003
Posts: 794
Location: Columbus, OH
|
 Posted: Tue May 19, 2015 3:38 am Post subject: Hostapd problem |
 |
|
There was an update to hostapd today...since then I can't get it to work. Getting this:
| Code: | * Starting hostapd ...
Configuration file: /etc/hostapd/hostapd.conf
nl80211: Could not configure driver mode
nl80211: deinit ifname=wlan0 disabled_11b_rates=0
nl80211 driver initialization failed.
wlan0: interface state UNINITIALIZED->DISABLED
wlan0: AP-DISABLED
hostapd_free_hapd_data: Interface wlan0 wasn't started
* start-stop-daemon: failed to start `/usr/sbin/hostapd'
* Failed to start hostapd
* ERROR: hostapd failed to start |
This is my hostapd.conf (nothing has changed). I've been through it and don't see any problems and it worked before.
| Code: | interface=wlan0
bridge=br0
driver=nl80211
logger_syslog=-1
logger_syslog_level=2
logger_stdout=-1
logger_stdout_level=2
ctrl_interface=/var/run/hostapd
ctrl_interface_group=0
ssid=triforce
hw_mode=g
channel=7
beacon_int=100
dtim_period=2
max_num_sta=255
rts_threshold=2347
fragm_threshold=2346
macaddr_acl=1
accept_mac_file=/etc/hostapd/hostapd.accept
deny_mac_file=/etc/hostapd/hostapd.deny
auth_algs=3
ignore_broadcast_ssid=0
wmm_enabled=1
wmm_ac_bk_cwmin=4
wmm_ac_bk_cwmax=10
wmm_ac_bk_aifs=7
wmm_ac_bk_txop_limit=0
wmm_ac_bk_acm=0
wmm_ac_be_aifs=3
wmm_ac_be_cwmin=4
wmm_ac_be_cwmax=10
wmm_ac_be_txop_limit=0
wmm_ac_be_acm=0
wmm_ac_vi_aifs=2
wmm_ac_vi_cwmin=3
wmm_ac_vi_cwmax=4
wmm_ac_vi_txop_limit=94
wmm_ac_vi_acm=0
wmm_ac_vo_aifs=2
wmm_ac_vo_cwmin=2
wmm_ac_vo_cwmax=3
wmm_ac_vo_txop_limit=47
wmm_ac_vo_acm=0
wpa=3
wpa_passphrase=*******
wpa_key_mgmt=WPA-PSK
wpa_pairwise=TKIP
rsn_pairwise=CCMP
ieee80211n=1
ht_capab=[HT40-][HT40+][SHORT-GI-40][TX-STBC][RX-STBC1][DSSS_CCK-40]
eapol_key_index_workaround=0
own_ip_addr=192.168.0.1 |
|
|
| Back to top |
|
 |
bbgermany
Veteran
Joined: 21 Feb 2005
Posts: 1844
Location: Oranienburg/Germany
|
| Posted: Tue May 19, 2015 5:47 am Post subject: |
|
|
Hi,
Which version of hostapd do you use? Do you have net.wlan0 started?
I had issues with hostapd as long as i haven't set the following for net.wlan0 in my /etc/conf/net
| Code: |
preup() {
rfkill unblock all
}
|
Maybe this helps you a bit.
_________________
Desktop: Ryzen 5 5600G, 32GB, 2TB, RX7600
Notebook: Dell XPS 13 9370, 16GB, 1TB
Server #1: Ryzen 5 Pro 4650G, 64GB, 16.5TB
Server #2: Ryzen 4800H, 32GB, 22TB |
|
| Back to top |
|
|
Akaihiryuu
l33t
Joined: 08 May 2003
Posts: 794
Location: Columbus, OH
|
| Posted: Tue May 19, 2015 1:43 pm Post subject: |
|
|
| I completely shut down my bridge (net.br0) and then brought everything back up and it worked. I guess something was holding the interface in such a way that hostapd couldn't set things properly. I was originally just trying /etc/init.d/hostapd restart without doing anything else. I think I'm going to add the rfkill command to preup anyway though because I did have a block error at some point during my messing with it. |
|
| Back to top |
|
|
solamour
l33t
Joined: 21 Dec 2004
Posts: 698
Location: San Diego, CA
|
| Posted: Tue Jul 21, 2015 1:27 am Post subject: |
|
|
I'm having the same problem, but I'm not using any bridges. Basically, I updated from "hostapd-2.0-r1" to "hostapd-2.4-r2", and this is what I'm getting.
| Code: | # /etc/init.d/hostapd start
* Caching service dependencies ... [ ok ]
* Starting hostapd ...
Configuration file: /etc/hostapd/hostapd.conf
nl80211: Could not configure driver mode
nl80211: deinit ifname=wlp0s15f5u1u4 disabled_11b_rates=0
nl80211 driver initialization failed.
wlp0s15f5u1u4: interface state UNINITIALIZED->DISABLED
wlp0s15f5u1u4: AP-DISABLED
hostapd_free_hapd_data: Interface wlp0s15f5u1u4 wasn't started
* start-stop-daemon: failed to start `/usr/sbin/hostapd'
* Failed to start hostapd [ !! ]
* ERROR: hostapd failed to start
|
And I made sure nothing was blocked.
| Code: | # rfkill list
4: phy4: Wireless LAN
Soft blocked: no
Hard blocked: no
|
Here is the output in the verbose mode.
| Code: | # /usr/sbin/hostapd -dd /etc/hostapd/hostapd.conf
random: Trying to read entropy from /dev/random
Configuration file: /etc/hostapd/hostapd.conf
ctrl_interface_group=0
rfkill: initial event: idx=4 type=1 op=0 soft=0 hard=0
nl80211: Supported cipher 00-0f-ac:1
nl80211: Supported cipher 00-0f-ac:5
nl80211: Supported cipher 00-0f-ac:2
nl80211: Supported cipher 00-0f-ac:4
nl80211: Using driver-based off-channel TX
nl80211: interface wlp0s15f5u1u4 in phy phy4
nl80211: Set mode ifindex 10 iftype 3 (AP)
nl80211: Setup AP(wlp0s15f5u1u4) - device_ap_sme=0 use_monitor=0
nl80211: Subscribe to mgmt frames with AP handle 0x9424830
nl80211: Register frame type=0xb0 (WLAN_FC_STYPE_AUTH) nl_handle=0x9424830 match=
nl80211: Register frame command failed (type=176): ret=-114 (Operation already in progress)
nl80211: Register frame match - hexdump(len=0): [NULL]
nl80211: Could not configure driver mode
nl80211: deinit ifname=wlp0s15f5u1u4 disabled_11b_rates=0
nl80211: Remove monitor interface: refcount=0
nl80211: Remove beacon (ifindex=10)
netlink: Operstate: ifindex=10 linkmode=0 (kernel-control), operstate=6 (IF_OPER_UP)
nl80211 driver initialization failed.
hostapd_interface_deinit_free(0x9421720)
hostapd_interface_deinit_free: num_bss=1 conf->num_bss=1
hostapd_interface_deinit(0x9421720)
wlp0s15f5u1u4: interface state UNINITIALIZED->DISABLED
hostapd_bss_deinit: deinit bss wlp0s15f5u1u4
wlp0s15f5u1u4: AP-DISABLED
hostapd_cleanup(hapd=0x9423f10 (wlp0s15f5u1u4))
hostapd_free_hapd_data: Interface wlp0s15f5u1u4 wasn't started
hostapd_interface_deinit_free: driver=(nil) drv_priv=(nil) -> hapd_deinit
hostapd_interface_free(0x9421720)
hostapd_interface_free: free hapd 0x9423f10
hostapd_cleanup_iface(0x9421720)
hostapd_cleanup_iface_partial(0x9421720)
hostapd_cleanup_iface: free iface=0x9421720
|
And the config file as a reference.
| Code: | interface=wlp0s15f5u1u4
driver=nl80211
logger_syslog=-1
logger_syslog_level=2
logger_stdout=-1
logger_stdout_level=2
ctrl_interface=/var/run/hostapd
ctrl_interface_group=0
hw_mode=g
beacon_int=100
dtim_period=2
max_num_sta=255
rts_threshold=2347
fragm_threshold=2346
macaddr_acl=0
auth_algs=3
ignore_broadcast_ssid=0
wmm_enabled=1
wmm_ac_bk_cwmin=4
wmm_ac_bk_cwmax=10
wmm_ac_bk_aifs=7
wmm_ac_bk_txop_limit=0
wmm_ac_bk_acm=0
wmm_ac_be_aifs=3
wmm_ac_be_cwmin=4
wmm_ac_be_cwmax=10
wmm_ac_be_txop_limit=0
wmm_ac_be_acm=0
wmm_ac_vi_aifs=2
wmm_ac_vi_cwmin=3
wmm_ac_vi_cwmax=4
wmm_ac_vi_txop_limit=94
wmm_ac_vi_acm=0
wmm_ac_vo_aifs=2
wmm_ac_vo_cwmin=2
wmm_ac_vo_cwmax=3
wmm_ac_vo_txop_limit=47
wmm_ac_vo_acm=0
eapol_key_index_workaround=0
eap_server=0
own_ip_addr=127.0.0.1
ssid=...
channel=1
wpa=3
wpa_passphrase=...
wpa_key_mgmt=WPA-PSK
wpa_pairwise=TKIP CCMP
rsn_pairwise=CCMP
accept_mac_file=/etc/hostapd/hostapd.accept
|
I'm not sure how to proceed from here. I'd appreciate any suggestions.
__
sol |
|
| Back to top |
|
|
solamour
l33t
Joined: 21 Dec 2004
Posts: 698
Location: San Diego, CA
|
| Posted: Tue Jul 21, 2015 8:17 pm Post subject: |
|
|
My problem is gone now. First, I pulled out the USB WiFi device that I was using with hostapd and inserted it again, not particularly I knew what I was doing but just to make sure I didn't miss anything obvious. That didn't solve the problem, but it now gave me a different error message.
| Code: | | VLAN: vlan_set_name_type: SET_VLAN_NAME_TYPE_CMD name_type=2 failed: Package not installed |
Quick research revealed that I needed CONFIG_VLAN_8021Q in the kernel, so I enabled the following. Not sure I really needed CONFIG_VLAN_8021Q_GVRP and CONFIG_VLAN_8021Q_MVRP, but well, I just enabled them while I was there.
| Code: | Networking support
Networking options
802.1Q/802.1ad VLAN Support (CONFIG_VLAN_8021Q)
GVRP (GARP VLAN Registration Protocol) support (CONFIG_VLAN_8021Q_GVRP)
MVRP (Multiple VLAN Registration Protocol) support (CONFIG_VLAN_8021Q_MVRP)
|
I rebooted the system, and the newer version of hostapd worked just as well as the old one.
__
sol |
|
| Back to top |
|
|
|
Networking & Security
