| View previous topic :: View next topic |
| Author |
Message |
mrfabiolo
Tux's lil' helper
Joined: 02 Jan 2011
Posts: 90
|
 Posted: Wed Nov 26, 2014 7:07 pm Post subject: [RISOLTO] /etc/fstab partizione NTFS |
 |
|
Ho una partizione NTFS sull'hard disk:
Generalmente posso montarla senza problemi così:
| Code: | | sudo mount /dev/sda5 /archive |
Però anche se metto la riga in /etc/fstab non viene montata in automatico.
| Code: | ┌❨0 ✓❩─[mrlogick@tux]─[3, 636KB]─[20:06]
└[~] ➤ cat /etc/fstab
# /etc/fstab: static file system information.
#
# noatime turns off atimes for increased performance (atimes normally aren't
# needed); notail increases performance of ReiserFS (at the expense of storage
# efficiency). It's safe to drop the noatime options if you want and to
# switch between notail / tail freely.
#
# The root filesystem should have a pass number of either 0 or 1.
# All other filesystems should have a pass number of 0 or greater than 1.
#
# See the manpage fstab(5) for more information.
#
# <fs> <mountpoint> <type> <opts> <dump/pass>
# NOTE: If your BOOT partition is ReiserFS, add the notail option to opts.
/dev/sdb2 / ext4 noatime,discard 0 1
/dev/sdb1 none swap sw 0 0
/dev/sd5 /archive ntfs-3g defaults 0 0
/dev/cdrom /mnt/cdrom auto noauto,ro 0 0 |
| Code: | ┌❨0 ✓❩─[mrlogick@tux]─[3, 636KB]─[20:04]
└[~] ➤ sudo fdisk -l
Password:
Disk /dev/sda: 465.8 GiB, 500107862016 bytes, 976773168 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disklabel type: dos
Disk identifier: 0x5ccf1688
Partition 3 does not start on physical sector boundary.
Device Boot Start End Blocks Id System
/dev/sda1 * 2048 718847 358400 7 HPFS/NTFS/exFAT
/dev/sda2 718848 307202047 153241600 7 HPFS/NTFS/exFAT
/dev/sda3 307204094 976773119 334784513 5 Extended
/dev/sda5 567173120 976773119 204800000 7 HPFS/NTFS/exFAT
/dev/sda6 307206144 404862975 48828416 83 Linux
/dev/sda7 404865024 502521855 48828416 83 Linux
/dev/sda8 502523904 567173119 32324608 83 Linux
Partition table entries are not in disk order.
Disk /dev/sdb: 22.4 GiB, 24015495168 bytes, 46905264 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0x0003a70a
Device Boot Start End Blocks Id System
/dev/sdb1 2048 1050623 524288 82 Linux swap / Solaris
/dev/sdb2 1050624 46905263 22927320 83 Linux |
Last edited by mrfabiolo on Wed Nov 26, 2014 8:35 pm; edited 1 time in total |
|
| Back to top |
|
 |
pierino_89
Guru
Joined: 03 Oct 2009
Posts: 522
|
| Posted: Wed Nov 26, 2014 7:12 pm Post subject: Re: /etc/fstab partizione NTFS |
|
|
| mrfabiolo wrote: |
# /etc/fstab: static file system information.
#
# noatime turns off atimes for increased performance (atimes normally aren't
# needed); notail increases performance of ReiserFS (at the expense of storage
# efficiency). It's safe to drop the noatime options if you want and to
# switch between notail / tail freely.
#
# The root filesystem should have a pass number of either 0 or 1.
# All other filesystems should have a pass number of 0 or greater than 1.
#
# See the manpage fstab(5) for more information.
#
# <fs> <mountpoint> <type> <opts> <dump/pass>
# NOTE: If your BOOT partition is ReiserFS, add the notail option to opts.
/dev/sdb2 / ext4 noatime,discard 0 1
/dev/sdb1 none swap sw 0 0
/dev/sd 5 /archive ntfs-3g defaults 0 0
/dev/cdrom /mnt/cdrom auto noauto,ro 0 0[/code]
|
Manca una lettera 
_________________
Linux registered user 461710 |
|
| Back to top |
|
|
mrfabiolo
Tux's lil' helper
Joined: 02 Jan 2011
Posts: 90
|
| Posted: Wed Nov 26, 2014 8:34 pm Post subject: |
|
|
| Scusate... che vergogna. |
|
| Back to top |
|
|
pierino_89
Guru
Joined: 03 Oct 2009
Posts: 522
|
| Posted: Wed Nov 26, 2014 8:41 pm Post subject: |
|
|
Ma sì, capita a tutti  ... Visto che usi ntfs-3g, considera anche le opzioni "locale" (nel caso trovassi caratteri strani nei nomi file) e "permissions":
| Code: |
permissions
Set standard permissions on created files and use standard access control. This option is set by
default when a user mapping file is present.
locale=value
This option can be useful when wanting a language specific locale environment. It is however dis‐
couraged as it leads to files with untranslatable chars to not be visible. |
_________________
Linux registered user 461710 |
|
| Back to top |
|
|
|
Forum italiano (Italian)
