| View previous topic :: View next topic |
| Author |
Message |
Sigma Kappa
n00b
Joined: 04 Mar 2012
Posts: 45
|
 Posted: Thu Sep 12, 2013 12:20 pm Post subject: wlan0: link is not ready |
 |
|
Hi,
the problem I encountered is "link is not ready". The appropriate "dmesg" and "rc.log" are listed below --- that's as far as I could get..
By passing the appropriate parameter to kernel I made sure network interfaces are not renamed.
My /etc/conf.d/net:
| Code: | # This blank configuration will automatically use DHCP for any net.*
# scripts in /etc/init.d. To create a more complete configuration,
# please review /usr/share/doc/openrc*/net.example* and save your configuration
# in /etc/conf.d/net (this file :]!).
modules="wpa_supplicant"
wpa_supplicant_wlan0="-iwlan0 -Dwext -c/etc/wpa_supplicant/wpa_supplicant.conf -d"
wpa_supplicant_wlan1="-iwlan1 -Dwext -c/etc/wpa_supplicant/wpa_supplicant.conf -d"
config_wlan0="dhcp"
config_wlan1="dhcp"
|
My wpa_supplicant.conf:
| Code: |
# wpa_supplicant -iwlan0 -c/etc/wpa_supplicant/wpa_supplicant.conf -d
ctrl_interface=/var/run/wpa_supplicant
ctrl_interface_group=wheel
update_config=1
# ap_scan=1
network={
ssid="mySSID"
psk="myPassphrase"
priority=5
}
|
| Code: |
rc shutdown logging started at Thu Sep 12 21:58:32 2013
* Caching service dependencies ...
[ ok ]
* Stopping local
[ ok ]
* Stopping gdm ...
[ ok ]
* Saving random seed ...
[ ok ]
* Deactivating additional swap space ...
[ ok ]
* Stopping syslog-ng ...
[ ok ]
* Bringing down interface wlan0
* Removing addresses
* Stopping wpa_cli on wlan0 ...
[ ok ]
* Stopping wpa_supplicant on wlan0 ...
[ ok ]
* Bringing down interface lo
* Removing addresses
* ::1
* Stopping D-BUS system messagebus ...
[ ok ]
* Unmounting loop devices
* Unmounting filesystems
* Unmounting /boot ...
[ ok ]
* Deactivating swap devices ...
[ ok ]
* Stopping udev ...
[ ok ]
* Setting hardware clock using the system clock [UTC] ...
[ ok ]
rc shutdown logging stopped at Thu Sep 12 21:58:34 2013
rc shutdown logging started at Thu Sep 12 21:58:32 2013
* Caching service dependencies ...
[ ok ]
* Stopping local
[ ok ]
* Stopping gdm ...
[ ok ]
* Saving random seed ...
[ ok ]
* Deactivating additional swap space ...
[ ok ]
* Stopping syslog-ng ...
[ ok ]
* Bringing down interface wlan0
* Removing addresses
* Stopping wpa_cli on wlan0 ...
[ ok ]
* Stopping wpa_supplicant on wlan0 ...
[ ok ]
* Bringing down interface lo
* Removing addresses
* ::1
* Stopping D-BUS system messagebus ...
[ ok ]
* Unmounting loop devices
* Unmounting filesystems
* Unmounting /boot ...
[ ok ]
* Deactivating swap devices ...
[ ok ]
* Stopping udev ...
[ ok ]
* Setting hardware clock using the system clock [UTC] ...
[ ok ]
rc shutdown logging stopped at Thu Sep 12 21:58:34 2013
rc boot logging started at Thu Sep 12 21:59:03 2013
* Setting system clock using the hardware clock [UTC] ...
[ ok ]
* Autoloaded 0 module(s)
* Checking local filesystems ...
/dev/sda7: clean, 397897/3670016 files, 1864997/14653696 blocks
/dev/sda5: clean, 35/25688 files, 24124/102400 blocks
[ ok ]
* Remounting root filesystem read/write ...
[ ok ]
* Remounting filesystems ...
[ ok ]
* Updating /etc/mtab ...
[ ok ]
* Activating swap devices ...
[ ok ]
* Mounting local filesystems ...
[ ok ]
* Configuring kernel parameters ...
[ ok ]
* Creating user login records ...
[ ok ]
* Cleaning /var/run ...
[ ok ]
* Wiping /tmp directory ...
[ ok ]
* Setting hostname to hp05_202 ...
[ ok ]
* Setting terminal encoding [UTF-8] ...
[ ok ]
* Setting keyboard mode [UTF-8] ...
[ ok ]
* Loading key mappings [us] ...
[ ok ]
* Bringing up interface lo
* 127.0.0.1/8 ...
[ ok ]
* Adding routes
* 127.0.0.0/8 via 127.0.0.1 ...
[ ok ]
* Mounting misc binary format filesystem ...
[ ok ]
* Loading custom binary format handlers ...
[ ok ]
* Activating additional swap space ...
[ ok ]
* setting up tmpfiles.d entries ...
[ ok ]
* Initializing random number generator ...
[ ok ]
rc boot logging stopped at Thu Sep 12 21:59:05 2013
rc default logging started at Thu Sep 12 21:59:05 2013
* Starting D-BUS system messagebus ...
[ ok ]
* Bringing up interface wlan0
* Starting wpa_supplicant on wlan0 ...
Initializing interface 'wlan0' conf '/etc/wpa_supplicant/wpa_supplicant.conf' driver 'wext' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' -> '/etc/wpa_supplicant/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
ctrl_interface_group='wheel'
update_config=1
Priority group 5
id=0 ssid='SSID'
WEXT: cfg80211-based driver detected
ioctl[SIOCSIWMODE]: Operation not supported
Could not configure driver to use managed mode
ioctl[SIOCGIWRANGE]: Operation not supported
ioctl[SIOCGIWMODE]: Operation not supported
ioctl[SIOCSIWAP]: Operation not supported
WEXT: Failed to clear to disconnect
netlink: Operstate: linkmode=1, operstate=5
Own MAC address: d0:df:9a:0f:e1:66
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
ioctl[SIOCSIWENCODEEXT]: Operation not supported
Driver did not support SIOCSIWENCODEEXT, trying SIOCSIWENCODE
ioctl[SIOCSIWENCODE]: Operation not supported
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
ioctl[SIOCSIWENCODEEXT]: Operation not supported
Driver did not support SIOCSIWENCODEEXT, trying SIOCSIWENCODE
ioctl[SIOCSIWENCODE]: Operation not supported
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
ioctl[SIOCSIWENCODEEXT]: Operation not supported
Driver did not support SIOCSIWENCODEEXT, trying SIOCSIWENCODE
ioctl[SIOCSIWENCODE]: Operation not supported
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
ioctl[SIOCSIWENCODEEXT]: Operation not supported
Driver did not support SIOCSIWENCODEEXT, trying SIOCSIWENCODE
ioctl[SIOCSIWENCODE]: Operation not supported
wpa_driver_wext_set_countermeasures
RSN: flushing PMKID list in the driver
Setting scan request: 0 sec 100000 usec
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: Supplicant port status: Unauthorized
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: Supplicant port status: Unauthorized
EAPOL: Supplicant port status: Unauthorized
ctrl_interface_group=10 (from group name 'wheel')
Added interface wlan0
Daemonize..
[ ok ]
* Starting wpa_cli on wlan0 ...
[ ok ]
* Backgrounding ... ...
* WARNING: net.wlan0 has started, but is inactive
* WARNING: netmount is scheduled to start when net.wlan0 has started
* Checking your configfile (/etc/syslog-ng/syslog-ng.conf) ...
[ ok ]
* Starting syslog-ng ...
[ ok ]
* Setting up gdm ...
[ ok ]
* Starting local
[ ok ]
rc default logging stopped at Thu Sep 12 21:59:08 2013
[ 7.522491] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
|
[/code] |
|
| Back to top |
|
 |
quilosaq
Veteran
Joined: 22 Dec 2009
Posts: 1522
|
| Posted: Thu Sep 12, 2013 6:29 pm Post subject: |
|
|
What's the output of | Code: | | dmesg | grep firmware |
? |
|
| Back to top |
|
|
Sigma Kappa
n00b
Joined: 04 Mar 2012
Posts: 45
|
| Posted: Fri Sep 13, 2013 9:12 am Post subject: |
|
|
| Code: | | dmesg | grep firmware |
yields these two lines:
| Code: |
ieee80211 phy0: rt2x00lib_request_firmware: Info -- Loading firmware file 'rt2860.bin'
ieee80211 phy0: rt2x00lib_request_firmware: Firmware detected - version: 0.34
|
|
|
| Back to top |
|
|
quilosaq
Veteran
Joined: 22 Dec 2009
Posts: 1522
|
| Posted: Fri Sep 13, 2013 4:33 pm Post subject: |
|
|
| Step to step. ¿? |
|
| Back to top |
|
|
Sigma Kappa
n00b
Joined: 04 Mar 2012
Posts: 45
|
| Posted: Tue Sep 17, 2013 7:14 am Post subject: |
|
|
| Code: | eth0: flags=4098<BROADCAST,MULTICAST> mtu 1500
ether 2c:41:38:9d:85:d7 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 20 memory 0xfe500000-fe520000
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
loop txqueuelen 0 (Local Loopback)
RX packets 28 bytes 1904 (1.8 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 28 bytes 1904 (1.8 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
tunl0: flags=128<NOARP> mtu 0
tunnel txqueuelen 0 (IPIP Tunnel)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
wlan0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether d0:df:9a:0f:e1:66 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
|
|
|
| Back to top |
|
|
Sigma Kappa
n00b
Joined: 04 Mar 2012
Posts: 45
|
| Posted: Tue Sep 17, 2013 7:31 am Post subject: |
|
|
OK, now I\m writing from my Gentoo box! 
I compiled rt2800pci as a module, without any change to the above wpa_supplicant.conf and /et/conf.d/net.
Thank you all. |
|
| Back to top |
|
|
|
Networking & Security
