View previous topic :: View next topic |
Author |
Message |
samo Guru
Joined: 13 Mar 2004 Posts: 489
|
Posted: Wed Jan 30, 2013 9:33 pm Post subject: udev-197-r4: renamed eth0 to enp1s4 and enp0s4 [solved] |
|
|
Hi,
I've updated udev-197-r4. Now I have problems with my network interface.
/etc/init.d/net.enp0s4 and /etc/init.d/net.enp1s4 are added to the default runlevel
Code: | # rc-update show | grep net.enp
net.enp0s4 | default
net.enp1s4 | default |
The dmesg output looks interesting:
Code: | skge: 1.14 addr 0xec000000 irq 17 chip Yukon-Lite rev 7
skge 0000:01:04.0: eth0: addr 00:11:2f:d5:ff:75
systemd-udevd[710]: renamed network interface eth0 to enp1s4
forcedeth 0000:00:04.0: ifname eth0, PHY OUI 0x732 @ 1, addr 00:11:2f:d5:e4:b3
systemd-udevd[708]: renamed network interface eth0 to enp0s4
forcedeth 0000:00:04.0: enp0s4: no link during initialization
skge 0000:01:04.0: enp1s4: enabling interface
skge 0000:01:04.0: enp1s4: Link is up at 100 Mbps, full duplex, flow control both |
I have two network cards. Only one is connected. I wonder why eth0 is renamed twice. I think with udev-197 the network names should be persistent.
ifconfig looks good:
Code: | # ifconfig
enp0s4: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
inet 192.168.178.20 netmask 255.255.255.0 broadcast 192.168.178.255
ether 00:11:2f:d5:e4:b3 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
enp1s4: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.178.21 netmask 255.255.255.0 broadcast 192.168.178.255
ether 00:11:2f:d5:ff:75 txqueuelen 1000 (Ethernet)
RX packets 37 bytes 2670 (2.6 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 17 bytes 1166 (1.1 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 17
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 16436
inet 127.0.0.1 netmask 255.0.0.0
loop txqueuelen 0 (Lokale Schleife)
RX packets 1 bytes 80 (80.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 1 bytes 80 (80.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 |
But e.g. ping does not work.
Only after stopping net.enp0s4 and net.enp1s4 and restart of net.enp1s4 it works
/etc/conf.d/net looks like this:
Code: | modules="wpa_supplicant"
wpa_supplicant_wlan0="-Dwext -iwlan0 -c/etc/wpa_supplicant/wpa_supplicant.conf -f /var/log/wpa_supplicant.log -dd"
wpa_timeout_wlan0=60
config_enp0s4="192.168.178.20 netmask 255.255.255.0 broadcast 192.168.178.255"
config_enp1s4="192.168.178.21 netmask 255.255.255.0 broadcast 192.168.178.255"
config_wlan0="192.168.178.22/24"
routes_enp0s4="default via 192.168.178.1"
routes_enp1s4="default via 192.168.178.1"
routes_wlan0="default via 192.168.178.1"
dns_servers_enp0s4="208.67.222.222"
dns_servers_enp1s4="208.67.222.222"
dns_servers_wlan0="208.67.222.222"
rate_wlan0="5.5M auto" |
Does anybody knows how to configure the network card correctly? is there anywhere a good tutorial for setting up network cards with the new udev version?
Last edited by samo on Sat Feb 02, 2013 9:16 pm; edited 1 time in total |
|
Back to top |
|
|
Hu Moderator
Joined: 06 Mar 2007 Posts: 21607
|
Posted: Thu Jan 31, 2013 2:53 am Post subject: |
|
|
This looks like a fundamental misconfiguration of your network setup, not related to the udev names. You have three different devices all assigned addresses in the same subnet, and all of them set to be the default route. This might work if you take care never to have more than one of them started at any given time. |
|
Back to top |
|
|
gentoo_ram Guru
Joined: 25 Oct 2007 Posts: 474 Location: San Diego, California USA
|
Posted: Thu Jan 31, 2013 4:31 am Post subject: |
|
|
I agree. What is it you are trying to achieve by having 3 network interfaces all on the same subnet? |
|
Back to top |
|
|
samo Guru
Joined: 13 Mar 2004 Posts: 489
|
Posted: Thu Jan 31, 2013 5:42 am Post subject: |
|
|
I would like to use lan or wlan alternatively. Normally I want to be connected via wlan. lan is only used when wlan is not available or in case of problems with wlan.
Is it necessary to remove the configuration of the unused device in /etc/conf.d/net? Or is it sufficient to remove the init script /etc/init.d/net.enp0s4 from the default runlevel?
Removing the init script is not sufficient. The output of dmesg and ifconfig looks same like before. eth0 is still renamed twice. |
|
Back to top |
|
|
samo Guru
Joined: 13 Mar 2004 Posts: 489
|
Posted: Thu Jan 31, 2013 8:11 pm Post subject: |
|
|
Now I have removed the configuration of the unused device. But eth0 is still renamed twice.
rc.log gives following info now:
Code: | * Bringing up interface enp0s4
* No configuration specified; defaulting to DHCP
* dhcp ...
* Running udhcpc ...
* start-stop-daemon: failed to start `/bin/busybox'
[ !! ]
[ !! ]
* ERROR: net.enp0s4 failed to start
* Bringing up interface enp1s4
* 192.168.178.21 ... [ ok ]
* Adding routes
* default via 192.168.178.1 ... [ ok ] |
I wonder why dhcp is starting. I didn't configure it because I would like to use static addresses. Is this done automatically by udev? Can I change this behaviour? |
|
Back to top |
|
|
Hu Moderator
Joined: 06 Mar 2007 Posts: 21607
|
Posted: Thu Jan 31, 2013 11:22 pm Post subject: |
|
|
According to the upstream udev maintainers, eth0 is supposed to be renamed twice. Under their latest naming scheme, your kernel always names the Ethernet card ethN, then udev races in and renames it to something else. Sometimes, udev arrives fast enough to free up the name eth0 before the next card is discovered and named. Sometimes, it may not. Either way, it is normal for all your other applications to see the card appear under one name, then change names a moment later. It is strange that enp0s4 is brought up on DHCP, assuming that the network configuration you pasted earlier is still accurate. |
|
Back to top |
|
|
samo Guru
Joined: 13 Mar 2004 Posts: 489
|
Posted: Fri Feb 01, 2013 5:12 am Post subject: |
|
|
Not exactly. According the hints above I've removed the configuration for the unused enp0s4 device. Additionally I've renamed the wlan device according the new udev name. Now /etc/conf.d/net looks as follows:
Code: | modules="wpa_supplicant"
wpa_supplicant_wlp0s2f2u5="-Dwext -iwlp0s2f2u5 -c/etc/wpa_supplicant/wpa_supplicant.conf -f /var/log/wpa_supplicant.log -dd"
wpa_timeout_wlp0s2f2u5=60
config_enp1s4="192.168.178.21 netmask 255.255.255.0 broadcast 192.168.178.255"
config_wlp0s2f2u5="192.168.178.22/24"
routes_enp1s4="default via 192.168.178.1"
routes_wlp0s2f2u5="default via 192.168.178.1"
dns_servers_enp1s4="208.67.222.222"
dns_servers_wlp0s2f2u5="208.67.222.222"
rate_wlp0s2f2u5="5.5M auto" |
Following scripts are started in the default runlevel:
Code: | net.enp1s4 | default
net.wlp0s2f2u5 | default |
net.enp0s4 is not started.
Is there a way to check the dhcp configuration? |
|
Back to top |
|
|
samo Guru
Joined: 13 Mar 2004 Posts: 489
|
Posted: Sat Feb 02, 2013 9:16 pm Post subject: |
|
|
I've got a solution here |
|
Back to top |
|
|
|